Usb device reconnects routinely

Hi!
I have a USB MIDI keyboard - M-AUDIO Keystation Pro 88.
A while ago I used to use another linux distro (Ubuntu) and everything went fine. Then I switched (back) to Arch Linux, and here's what's gone wrong: my keyboard  began to reconnect all the time, even while I'm actually playing and it's quite annoying .
Here's a cut from everything.log:
Aug 28 04:49:14 brainburner kernel: usb 6-1: USB disconnect, address 79
Aug 28 04:49:14 brainburner kernel: usb 6-1: new full speed USB device using uhci_hcd and address 80
Aug 28 04:49:15 brainburner kernel: usb 6-1: configuration #1 chosen from 1 choice
Is there any way to fix this behavior?
Thanks in advance for any help.

I think in Ubuntu it's a 2.6.29 branch - I haven't tried installing it here, I just use the "stock" kernel (2.6.30). And I don't even know the version of X or driver in Ubuntu .
As for lsmod - do I need to run it with device unplugged after reboot? I did that without rebooting, just unplugged the device, lsmod, plugged in device, lsmod and diff - the outputs were equal. But it is just a USB-MIDI device. lsmod shows these:
yurique@brainburner:~$ lsmod | grep usb
usbhid 40608 0
hid 42496 1 usbhid
btusb 12632 0
bluetooth 56676 1 btusb
snd_usb_audio 86304 0
snd_usb_lib 17252 1 snd_usb_audio
snd_rawmidi 21856 2 snd_seq_midi,snd_usb_lib
snd_hwdep 7656 2 snd_usb_audio,snd_hda_codec
snd_pcm 73672 6 snd_usb_audio,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd 58436 20 snd_usb_audio,snd_rawmidi,snd_hda_codec_realtek,snd_seq_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_hwdep,snd_pcm,snd_timer
usbcore 150192 7 usbhid,btusb,snd_usb_audio,snd_usb_lib,uhci_hcd,ehci_hcd
yurique@brainburner:~$ lsmod | grep midi
snd_seq_midi 6848 0
snd_rawmidi 21856 2 snd_seq_midi,snd_usb_lib
snd_seq_midi_event 7012 2 snd_seq_midi,snd_seq_oss
snd_seq 53744 9 snd_seq_midi,snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 6768 5 snd_seq_midi,snd_rawmidi,snd_seq_dummy,snd_seq_oss,snd_seq
snd 58436 20 snd_usb_audio,snd_rawmidi,snd_hda_codec_realtek,snd_seq_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_hwdep,snd_pcm,snd_timer
p.s. sorry for the long delay
Last edited by yurique (2009-09-01 15:25:33)

Similar Messages

  • Please help me, USB Devices instantly disconnect/reconnect when using keyboard

    I own a Lenovo 3000 C200. IIf I start typing while I have any USB device plugged in (USB mouse, Removable HDD, etc), the USB device instantly disconnects and reconnects again. As long as I don't touch my keyboard, the USB device will work fine. I have noticed that this does not happen when I press the the other keys like the Lenovo care button, volume increase / decrease key, etc. and doesn't happen when I use the touchpad. I have not dropped or damaged my machine in any way.
    At the beginning, thinking it might be a windows problem, I had re-installed windows (XP) with no drivers installed and the problem persisted. I installed the latest update available for the BIOS still with no luck. I have checked the BIOS, however there is nothing related in anyway that can be configured.
    Just now I have noticed that the problem begins, as soon as I turn on the machine. Hardware problem perhapsI
    Please help me.
    Moderator Note; Message Subject edited
    Message Edited by andyP on 08-18-2008 08:58 PM

    This happened to me exactly the same, you must updated the latest bios version 2.06.
    Now go to the Lenovo website to download the oldest version 1.02  and the 1.08, first flash the 1.02 then flash again using the 1.08 that it, don't use the 2.06 which is the porblem source file for some 3000 notebooks.

  • Windows 7 keeps freezing, disconnecting/reconnecting USB devices

    Last week, a lightning strike near where I live caused a power surge and as a result, my ethernet card was fried.  I took my computer (iMac) to a store to have it repaired, and they wound up replacing the entire motherboard (a bit extreme in my opinion, but what do I know).
    When I got it back today, sure the ethernet problem was solved, but I noticed that my taskbar was acting weird - specifically the icons in the notification tray.  Lots of them were "blank", meaning there were just empty spaces that would highlight when I hovered the cursor over them, but nothing happened when I clicked them.
    Then I discovered that clicking any of the icons in the notification tray almost immediately froze the computer.  Frozen, as in completely unresponsive to the point where my only option was to manually shut off the computer.  That happened twice.
    My solution was to reboot in safe mode and run system restore to an earlier point.  That fixed the notification tray problem (no more freezing, and the icons were all back), but the computer still keeps freezing at random intervals.  Again, my only solution is to manually shut it off by holding down the power button, which I hate doing because I know it's bad for the hard drive.  Sometimes it froze as soon as the welcome screen.  I tried running a virus scan, but again it froze in the middle of the process.
    On top of the constant freezing, it keeps disconnecting/reconnecting my usb devices.  My mouse and keyboard will suddenly drop out for five seconds and then start working again.  This constantly happens, to the tune of several "disconnect" sounds playing over the speakers.
    What the heck is going on?  I tried re-installing the Boot Camp drivers, but that didn't work.  I have my Windows 7 CD and backed up files, so if worse comes to worst I can do a clean install of Windows, but I'd rather not have to spend a day re-building my computer, and I'd REALLY rather not take it back in for another repair, since that took a week and I need this for my work.
    Any ideas on what I should do?  I'm out of town on my laptop for the weekend, and I'd like to have a game plan for when I get back.

    I'm very excited to finally have a solution for this problem. Thank You Balaji for figuring this out. I've been struggling with this for a number of years, and had only one USB Hard Drive that worked. I too have VMware workstation, and had the missing files
    in "c:\windows\inf." I can say with certainty that I did not delete the files from that folder, but something is common in both of our situations. Maybe it has to do with VMware, and some of it's updates over the years. I'm also using nCompute to share out
    a networked desktop via the wire. 
    One more thing worthy of mention is this machine was an update from Windows Vista, and the USB hard drive that worked was configured back than. So although I could never add another HD, at least I had the one.
    Now with having copied over the files, I can plugin other USB enclosures with different drives and they too are working.
    Like you mentioned, it was always possible to use USB devices within my Virtual Machines, so it was clear that the USB ports were functional. I actually got the files from a clean Windows 7 VM, copying out the \windows\inf folder and doing a compare between
    the the real one and the virtual one. I found the two missing files you mentioned, along with 8 others. I went ahead and included them all in your fix.
    It worked, Amazing. Thanks again. :O)

  • Envy Touchsmart 15-j105sa Continuous USB Device Dropout and Reconnect

    New Envy Touchsmart 15-j105sa running an up to date version of Windows 8.1.  All HP driver and Windows updates completed prior to installing software and other USB devices except for USB WiFi adaptor and software.
    USB 2.0 HDD keeps disconnecting from the port and then re-connecting.  This happens continuously about once every 30sec.  It re-connects after about 10sec and then disconnects again after about 30sec.  When connected everything seems to be working fine.  Access to the HDD is OK, it shows normally in Device Manager and Safe Disconnect.
    I have uninstalled the USB drivers and restarted.  The problem persists.  I have powered the USB HDD externally.  The problem persists.  I have tried connecting to 3 of the 4 USB ports.  The problem persists.  The USB 2.0 HDD works normally on other Laptops.  When data is being transferred the dropout does not occur.  It appears to be associated with idle time on the USB HDD.
    I don't get the problem when I attach a USB 3.0 HDD.  It stays connected with no dropout.  Flash drives don't have the problem.
    I also have a similar issue connecting a USB Alfa WiFi Adaptor.
    UPDATE:  The problem is related to an External Combo Drive.  2.5" Sata to USB /eSata HDD External Enclosure.  As long as the HDD is being accessed then there is no dropout.  As soon as the disc becomes idle I get a cycle of disconnects and reconnects as described above.  I would like to understand the cause of this issue because it will help solve the massive connect/disconnect hunting that I get with my external USB wifi adaptor.  Once the Alfa Wifi adaptor gets happy with its connection the hunting stops and it behaves normally.

    Are you using the charging USB 3.0 ports or the standard USB 3.0 port to connect the device?
    Charging ports have a + next to them. It really should not make a difference, but it might with your keyboard since it does require more power then, perhaps a mouse.
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Power to USB Devices

    My rMBP will recognize and utilize both the Apple USB Superdrive, and a Pioneer BDR-XD05W, as such laptops have extra power via the USB port.  My new Mac Pro will only recognize the Pioneer (which is USB3 compatible) via the USB2 on the connected TBolt Apple display (which is where I have regularly used the Apple drive, it being only rated for USB2.)
    Are none of the onboard nMP USB ports capable of providing the needed power?  Guess I will be getting a Pioneer power adaptor.
    Ernie

    After consulting a Genius at the Apple Store, where I was told the ports on the new Mac Pro should provide the needed power, proceeded to make other tests to see when and if it would be recognized.
    I disconnected every USB device from the nMP, and then connected the Pioneer drive to various of the USB ports that should provide USB3.  The device was now recognized on all of them.  I then reconnected a powered USB3 drive I am using routinely, and then two other cables not active at the moment.  Recognition of the Pioneer was not disturbed by this.  I will have to experiment in time to see what if any activity can change this.
    I find the document linked below confusing as to possible sequencing issues with USB connections:
    Apple Computers and Displays: Powering peripherals through USB
    Ernie

  • USB device keeps disconnecting/connecting after upgrading to Windows 8.1

    I have a device(Pedal for Sim Racing) connected via USB, everything is working fine in Windows 7 and 8 but after upgrading my machine to Windows 8.1 the device keeps disconnecting and connecting for like every 2 seconds. But after I open the Property Sheet
    in Game Controllers panel the disconnection issue was gone, if I reconnect the device the issue persist. Other people who have similar device also encounters the same issue after upgrading to windows 8.1. The issue persist with or without the device driver
    installed. 
    Any idea, what might cause this? 
    Best regards
    mark

    I'v got this exact same problem with my Win 7 desktop.  I've also got pedals and wheel but don't see it as different than all the other USB devices.  I'm using a bunch of USB, but no hubs, including 3 external storage hard drives. But the momentary
    disconnect appears in all devices as best as i can see..even my long time trouble free head phones..keyboard..and all.  Sometimes the sound goes away and if I unplug and replug them the sound comes back, and other times I have to exit and re enter the
    game. I also get video crashes ..maybe not related.IDK..and have to restart all, because I've got three black screens in Eyefinity. For years my system was trouble free and its just slowly started getting worse. I've thought it had to do with system "sleep"
    etc but long ago went to never sleep max performance etc..Makes no difference. Keep thinking its my hardware or my house wiring etc..But can't seem to solve it. I replaced my Mobo/chip/ram maybe 6 months ago and that appears to have not helped.  It seems
    to be getting worse. I hate to start replacing parts piece by piece..cost a lot of money and sometimes doesn't help.
    When I'm playing a game I can often hear "faint" sound of USB connect disconnect happening with regularity..that little bing/boink sound etc..So it must just be constantly happening...Seems weird. Didn't have anything like this happening years
    ago with pretty much the same hardware and same Win7 with the continuing updates etc.
    What can be causing this common problem?

  • My hp photosmart premium all in one keeps telling me randomly to remove my usb device.

    My HP 309 all in one Photo smart Premium Wireless Printer,gives me a remove your usb device reading .None is attached.
    I can reboot it and it goes away ; but returns later.I even connected one and removed it but it did not help.
    I also can"t get my auto feeder to work.I took it to Best Buy and he didn't know what to do either.

    Hello there! Welcome to the forums @mrsddavis ,
    I read your post about the troubles you're having with the printer telling you to "remove a USB device", when you do not have a USB device plugged into the unit. I have a couple suggestions that I hope will help you. You may have tried all of the steps to my first idea, if so move on to the second one. Also, the second step will be in a private message to you, as it cannot be posted publicly.  In regards to the ADF not working, let me know what the problem is, for example, will it pull in paper and then jam, or will it not pull paper in at all? Let me know so I can research that problem for you.
    If you are not sure how to check your forum messages this post, has instructions.
    Power reset:
    Press the Power button to turn on the product.
    With the product turned on, disconnect the power cord from the rear of the product.
    Unplug the power cord from the wall outlet.
    Wait at least 30 seconds.
    Plug the power cord back into the wall outlet.
    Reconnect the power cord to the rear of the product.
    If the product does not turn on by itself, press the Power button to turn it on.
    Ensure the printer is plugged in directly to the wall outlet, avoiding power bars and surge protectors. This ensures the printer is receiving full power and may help greatly.
    Good luck, I hope this helps
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • USB Device Not Recognized - is my iPod toast?

    Got a new computer recently with Win XP. When I try to connect my iPod with a USB adapter I keep getting "USB Device not Recognized" and if I click that I get "Try reconnecting the device. If Windows still does not recognize it, replace the device."
    I can connect other USB devices like my compact flash cards etc. The iPod was working on my old computer.
    Any ideas??
    Thanks in advance for any help!!!

    I had a new ipod and windows wasnt recognizing it or giving me the message "new hardware found" and then telling me the drivers were missing... this is what I did and it fixed my problem.
    1. go to www.driverguide.com and sign up (for free)
    2. download usbstor.sys & usbstor.inf (and take note of where you download them to)
    3. update drivers by selecting folder you downloaded the two files to
    4. restart computer
    5. open itunes and then connect ipod
    good luck
    -jackie

  • Can't attach USB devices in Windows XP Mode

    I am still trying to set up my new Probook G1 450.  It is presently in the original Win 7 Pro 64-bit OS.
    I am trying to use Windows XP Mode.  I can set up XP Mode, but I can't get USB access under it. But for me, the whole point of getting XP Mode is to be able to run two key programs which require USB access. The USB devices have been successfully installed in Win 7 (it's the programs that require XP Mode).
    I have tried with VMLiteXPMode, Virtual Box, and finally with Windows Virtual PC. The results are about the same. I am presently trying Windox Virtual PC. When I access the USB button on the top of the XP Mode box, there is a list of all the USB devices. This looks like things are fine. All the devices are there. Hooray. Oops, too soon! It still doesn't work. One still has to "attach" the USB device, by clicking its listing under USB devices. When I do this, I get the following error message:
    "Could not attach the USB device. You can attach the USB to a different USB port or restart the virtual machine and try again."
    Yes, I can and have done all those things, and  I get the same error message again and again and again. This is true for all USB devices (except the USB mouse, which works perfectly and automatically in XP mode and is *not* listed under USB):
    * Epson Perfection scanner 
    * HP Laserject printer
    * the computer's own HP HD Webcam,
    and
    * the computer's own Wireless/Bluetooth Device
    For example, the scanner and printer will work well in the host machine, where I have installed them, but they can't be "attached" in XP Mode.
    Notes:
    * I have enabled "integration features"
    * I have tried disconnecting and reconnecting the devices.
    * If I try to install the printer in XP Mode, I can't do that, because this requires, at some point, the printer being plugged in to the USB. And I get the above error message when I try to attach it.
    Also I have already had to deal with one driver issue (it came with the wrong driver for wireless; the right driver wasn't on the HP support page and couldn't be obtained by the computer's own "update' function),  but when I finally discovered the right driver, wireless worked flawlessly
    There is yet another possible driver issue, but I'll leave that for another topic later. One thing at a time.

    @comvox 
    ‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
    If you are unfamiliar with the Forum's private messaging please click here to learn more.
    Thank you,
    Omar
    I Work for HP

  • HT201401 MTP USB Device not installed

    Hello -
    I'm new to this community message board.
    I recently started having this problem about two months ago.  Up til that time I didn't have this problem.
    When I would connect my iPhone 4S to my windows 7 computer, the folder files would pop up and ask if I wanted to open the files from the iPhone connection through the USB port that I have always used.
    It started two months ago, that when I connected my iPhone in the same way that I have always connected through the USB port, that instead Windows would recognize the connection but attempt to install the drivers. A message always comes up saying that Windows can not install the MTP USB Device because It can not load the drivers for this device and Code 31.
    I've searched the web for solutions but have not found any that fix this problem. These are troubleshooting things that I have tried:
    I have downloaded and installed the lastest iTunes application.
    I have upgraded the iPhone to the lastest IOS
    I have reset the iPhone, then reconnected to USB port on computer
    I have connected the iPhone to another USB port on my computer
    I have selected an earlier Windows System Restore point at a time before this problem existed and restored my computer
    I have used the Windows 7 installation disk to repair the Windows Operating System
    I have uninstalled the drivers for the iPhone in Device Manager, restarted the computer and then connected the iPhone and USB cable to the computer.
    I have used another USB Cable to connect the iPhone to the computer.
    I have looked in Control Panel under Devices - the Apple Mobil Device Driver is displayed with no problems. However the iPhone is displayed with a triangle and an exclamation mark in the triangle.
    I have viewed Device Manager in Windows 7 and looked in these categories: Universeral Serial Bus Controller - everything is okay, no triangles with exlamation marks in them or any other markings on any of the Standard Enhanced PCI to USB Controllers. The Category in Device Manager called Human Interface Devices also looks okay.
    In Device Manager the category Portable Devices lists H:\, MTP USB Device, WPD File System Device Driver all have the small yellow triangle with the exclamation mark in the triangle. When I double click to open these devices up in Device Manager they all say the device is not working properly because windows can not load the drivers required for this device. (Code 31).
    Windows 7 still does not recognize the iPhone as it use to do with the open file window that pops-up when the iPhone is connected to computer. Windows shows these drivers for the iPhone on my computer and these show up in the properties of the MTP USB Device - which is what Windows 7 calls the iPhone connection.
    UMDF\WpdMtpdDr.dll
    winusb.sys
    WUDFRd.sys
    WpdMtp.dll
    WpdMtpUS.dll
    So has anyone had this problem of Windows giving error message “can not load drivers for this device and Code 31” and is there a fix?
    Thank you if you can help with this problem.

    I had the same iss - it's a known issue whereby Windows attempts to use the wrong driver to access the phone.
    BACK UP YOUR REGISTRY!!! Editing the registry can be (read: IS) dangerous and can cause no end of pain if done incorrectly.(But dont wort..i did it...)
    - To Back Up your Registry: Click Start menu and click "Run". Type "regedit". Click File, then choose export and type "iphone driver fix registry backup".
    - Click Export and let it export the the registry to a file.
    - To fix the issue: Follow the folder tree on the left to: hkeylocalmachine > system > current control set > control > class
    - Find “{EEC5AD98-8080-425F-922A-DABF3DE3F69A}” down the LEFT hand side and click on it.
    - Under the list on the RIGHT hand side find "UpperFilters"
    - Right-Click UpperFilters and click delete
    - Close the registry editor and restart your PC (without the iphone attached).
    - Once restarted and logged back in, plug in your iphone and voila!  Windows will actually choose the correct driver and you'll be in like flynn.

  • Windows won't recognize my iPod - USB device not recognized

    This is really frustrating. So I got a 4gb iPod nano on Saturday, took it home, set it up and everything was going just fine, no worry's. About 4 hours later I went to adjust my songs and it would not come up in iTunes. A little pop-up box said that the "USB device not recognized - one of the USB devices attached to this computer has malfunctioned and windows does not recognize it." After owning my iPod for less than an afternoon, I now have an ipod that I can do nothing to including change the music, charge it, etc. It works normally otherwise, it just won't connect to my computer. I then plugged in my older 256mb usb stick, and the same message, it too does not get recognized by windows. So I then tried a brand new 1gb usb stick that I had and the same result, not recognized by windows. I updated my itunes to the latest one after purchasing my ipod (version 7.4.3.1) and have looked up everything that I can and tried everything I saw to try, but nothing, absolutely nothing, worked. However my usb mouse, usb joystick, and usb printer all still work, but my moniter that has four usb outlets on it causes the same message, if I plug in the cable that connects one usb on my computer to the four on my moniter, windows can not recognize it. When I look in my device manager at the "unknown device" under the usb controller list it says that there is not driver for it, however I know that the drivers are either on my computer or built into windows. Any help? Anybody have an idea about what to do? Is it something in my windows registry has changed because of the new itunes, etc.?

    Now that I've had some sleep, I realise I didn't really provide information that may lead to some specific help. Here goes - when I first plugged in the ipod nano (8gb), It displayed the screen it was supposed to - I could see the lightning bolt through the battery icon and knew it was charging. The icon for the ipod also appeared in the left-hand listing in itunes (in the section that existed under Library, before the sections Store and Playlists). This section now does not appear (I can't remember the title of this section, but it might have been 'devices'). In fact, I'm pretty sure this problem started when I clicked on this icon - nothing happened and it disappeared - so did the display on the ipod, which is not just the apple. This means itunes has only Library, Store and Playlist in the left-hand colunm. While I accept that computers do not work on normal logic, this seems to me to indicate that the drivers are fine, the system is fine, my laptop is fine - its the ipod or the usb cord. This morning as I tried again, this time my laptop gave me the option to 'click on the balloon to solve the problem' - let me quote: "One of the USB devices attached to this computer has malfunctioned, and Windows does not recognise it. Try reconnecting the device. If Windows still does not recognise it, replace the device". Come on folks - one of you will surely know how to fix this (short of me taking the ipod back to the store to get my money back).

  • USB devices all of a sudden no longer recognized in windows 7

    Hi,
    I am using a HP Pavilion Simline s5550nl edition with windows 7 home premium (64-bit) since 1.5 years. Never had any problems until 3 days ago. Since 3 days suddenly some new devices, already plugged-in devices and previously used devices are no longer recognized (USB-device not recognized-error after plug-in).
    I used an USB-mouse, USB-keyboard, Smartcard-reader, Sony Story 1.5TB External HDD, USB WebCam. They al worked fine.
    3 Days ago I bought a WD Elements 2 TB External HDD. After plugging in, it was not recognized at first. Replugging it in it was recognized, but trying to open the drive in Explorer, it gave a not-formatted-error (while the disk should have been pre-formatted for Windows 7). However, i tried to format the disk, but it could not reach it any more. After rebooting the system the WD elements HDD gave the USB-device-not-recognized-error, using all other USB-ports didn't change that. In fact my Sony External HDD was no longer reachable either. Unplugging and replugging it in gave the same USB-device-not-recognized-error. Trying previously flawless working USB-devices all gave the same USB-device-not-recognized-errors (USB-flash disk 4GB, External HDD 2.5inch 160GB, USB-/card reader HUB, iPhone).
    I then tried to connect my Sony and WD external HDD on my other computer with windows XP SP3. They were recognized within seconds and working fine (also the WD elements External HDD indeed turned out to be pre-formatted).
    Strangely enough my USB-mouse, USB-keyboard and smartcard-reader kept being recognized at plug-in. Furthermore, my printers (connected over LAN) and NAS (connected over LAN) were usable without any problem. I did not encounter any other problems in functionality of windows. I then thought it might be a corrupted general USB-driver for mass-storage or something, so I started to google this problem. Things I have done so far (before each step I unplugged all USB-devices, rebooted and reconnected the devices):
    - Turning computer off, unplug power-cable for 2 minutes, reboot.
    - Updating BIOS to version 6.04 (was running version 6.02).
    - Uninstalling all USB-devices/mainhubs etc in devicemanagement, automatic reinstallation at restart.
    - Try installing newer USB-drivers for mainhubs, messages the installed drivers are already the latest.
    - Uninstalling all 'hidden' USB-devices.
    - Trying to go back to configuration of 1 day ago (maximum i could go back), resulted in an error that  the file might be corrupted.
    - Turning computer off, unplug power-cable overnight, reboot.
    - Running HP-systemdiagnostics: all passed.
    - Running Norman anti-virus scan (latest update): no infection.
    - Again uninstalling all USB-devices/mainhubs etc, automatic reinstallation at restart.
    I also noticed that during the night before this malfunction appeared (so actually several hours), on january 20th, an automated microsoft critical update was installed (some anti-spyware definition update). I am now thinking it might still be a driver-problem of some sort of general USB-mass storage driver or due to this microsoft update or maybe some clever virus.
    I no ordered a Recovery disk (never had to use one, so did not jet own one), to recover windows and if that doesn't help reinstall it. However I hope that anyone can bring up a solution that I am overlooking?
    D. Berks

    OK, meanwhile I found that only uninstalling the USB2-driver enables the USB-ports again. Uninstalling it makes al devices recognizable, whil reintsalling it immediately makes all USB-devices unrecognizable.
    I tried updating the driver to the latest version, deleting it (after reboot an automated reinstall is triggered), but nothing helps. As if soething that stays in the system makes USB2 to corrupt USB-channeling or something.
    I strongly believe that it has something to do with the windows-update, but I can nowhere as a question about it to microsoft (will cost 70 euro's!).
    Does anybody knows what this could be? Or better: knows of a solution?
    Tanks,
    D. Berks

  • USB Device Not Recognized  - Windows XP

    The IPOD 5G and my computer were working just fine until the computer stopped detecting the IPOD. I get this message:
    USB Device not Recognized. The USB device attached to this computer has malfuctioned and Windows does not recognize itit. Try reconnecting the divice(ipod) If Windows still does not recognize it, replace the device."
    IPOD still works and is recognized by my work laptop. What driver needs to be installed for the ipod to be recongized?
    Help me
      Windows XP  

    Someone here said that you need two drivers usbstor.sys and usbstor.inf I found them at driverguide.com. I have not tried to load them yet but I will probply tommorrow.My coumputer will not see ipod as a hard drive, it loads video fine and all my music but no pics.

  • I can no longer charge my iPhone5 through either of my macbook pros. I get the error message that a USB device is using too much power. Can anyone help?

    I can no longer charge my iPhone5 through either of my macbook pros. I get the error message that a USB device is using too much power. Can anyone help?

    I reconnected the original powered hub that I thought probably caused the problem and this time it shut down the whole computer. When I rebooted everything now works perfectly. The system reset. I tried another powered hub and it didn't have the same effect so the old one is heading for the bin and with fingers crossed all systems are now working perfectly. Trying to reset PRAM or reset the SMC didn't work but causing the same power issue did. Thanks for your input though. It did get me to think what was the original cause.
    Cheers
    Guy

  • Problem with usb devices

    hi guys,
    i have a problem with my usb devices.
    the dmesg:
    Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009
    Command line: root=/dev/sda5 vga=0x0361 ro
    KERNEL supported cpus:
    Intel GenuineIntel
    AMD AuthenticAMD
    Centaur CentaurHauls
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
    BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
    BIOS-e820: 000000007fed0000 - 000000007fee3000 (ACPI NVS)
    BIOS-e820: 000000007fee3000 - 0000000080000000 (reserved)
    BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
    BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
    BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
    DMI present.
    Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
    e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    last_pfn = 0x7fed0 max_arch_pfn = 0x100000000
    MTRR default type: uncachable
    MTRR fixed ranges enabled:
    00000-9FFFF write-back
    A0000-BFFFF uncachable
    C0000-FFFFF write-protect
    MTRR variable ranges enabled:
    0 base 000000000 mask F80000000 write-back
    1 base 07FF00000 mask FFFF00000 uncachable
    2 disabled
    3 disabled
    4 disabled
    5 disabled
    6 disabled
    7 disabled
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    Scanning 0 areas for low memory corruption
    modified physical RAM map:
    modified: 0000000000000000 - 0000000000010000 (reserved)
    modified: 0000000000010000 - 000000000009f800 (usable)
    modified: 000000000009f800 - 00000000000a0000 (reserved)
    modified: 00000000000ce000 - 00000000000d0000 (reserved)
    modified: 00000000000dc000 - 0000000000100000 (reserved)
    modified: 0000000000100000 - 000000007fed0000 (usable)
    modified: 000000007fed0000 - 000000007fee3000 (ACPI NVS)
    modified: 000000007fee3000 - 0000000080000000 (reserved)
    modified: 00000000e0000000 - 00000000f0000000 (reserved)
    modified: 00000000fec00000 - 00000000fec10000 (reserved)
    modified: 00000000fed00000 - 00000000fed00400 (reserved)
    modified: 00000000fed14000 - 00000000fed1a000 (reserved)
    modified: 00000000fed1c000 - 00000000fed90000 (reserved)
    modified: 00000000fee00000 - 00000000fee01000 (reserved)
    modified: 00000000ff000000 - 0000000100000000 (reserved)
    init_memory_mapping: 0000000000000000-000000007fed0000
    0000000000 - 007fe00000 page 2M
    007fe00000 - 007fed0000 page 4k
    kernel direct mapping tables up to 7fed0000 @ 10000-14000
    RAMDISK: 37d42000 - 37fefc39
    ACPI: RSDP 00000000000f7fe0 00024 (v02 PTLTD )
    ACPI: XSDT 000000007fedab41 0008C (v01 Sony VAIO 20070418 PTL 00000000)
    ACPI: FACP 000000007fee1bd2 000F4 (v03 Sony VAIO 20070418 PTL 00000001)
    ACPI: DSDT 000000007fedbeeb 05C73 (v02 Sony VAIO 20070418 PTL 20050624)
    ACPI: FACS 000000007fee2fc0 00040
    ACPI: APIC 000000007fee1cc6 00068 (v01 Sony VAIO 20070418 PTL 0000005A)
    ACPI: HPET 000000007fee1d2e 00038 (v01 Sony VAIO 20070418 PTL 0000005A)
    ACPI: MCFG 000000007fee1d66 0003C (v01 Sony VAIO 20070418 PTL 0000005A)
    ACPI: TCPA 000000007fee1da2 00032 (v01 Sony VAIO 20070418 PTL 00005A52)
    ACPI: SLIC 000000007fee1dd4 00176 (v01 Sony VAIO 20070418 PTL 01000000)
    ACPI: TMOR 000000007fee1f4a 00026 (v01 Sony VAIO 20070418 PTL 00000003)
    ACPI: APIC 000000007fee1f70 00068 (v01 Sony VAIO 20070418 PTL 00000000)
    ACPI: BOOT 000000007fee1fd8 00028 (v01 Sony VAIO 20070418 PTL 00000001)
    ACPI: SSDT 000000007fedbc29 002C2 (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI: SSDT 000000007fedb159 0025F (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI: SSDT 000000007fedb0b3 000A6 (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI: SSDT 000000007fedabcd 004E6 (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI: BIOS bug: multiple APIC/MADT found, using 0
    ACPI: If "acpi_apic_instance=2" works better, notify [email protected]
    ACPI: Local APIC address 0xfee00000
    (7 early reservations) ==> bootmem [0000000000 - 007fed0000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
    #2 [0000200000 - 000082d0d0] TEXT DATA BSS ==> [0000200000 - 000082d0d0]
    #3 [0037d42000 - 0037fefc39] RAMDISK ==> [0037d42000 - 0037fefc39]
    #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
    #5 [000082e000 - 000082e204] BRK ==> [000082e000 - 000082e204]
    #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
    found SMP MP-table at [ffff8800000f8010] f8010
    [ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001200000-ffff880002dfffff] on node 0
    Zone PFN ranges:
    DMA 0x00000010 -> 0x00001000
    DMA32 0x00001000 -> 0x00100000
    Normal 0x00100000 -> 0x00100000
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009f
    0: 0x00000100 -> 0x0007fed0
    On node 0 totalpages: 523871
    DMA zone: 56 pages used for memmap
    DMA zone: 1682 pages reserved
    DMA zone: 2245 pages, LIFO batch:0
    DMA32 zone: 7108 pages used for memmap
    DMA32 zone: 512780 pages, LIFO batch:31
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Using ACPI (MADT) for SMP configuration information
    ACPI: HPET id: 0x8086a201 base: 0xfed00000
    SMP: Allowing 2 CPUs, 0 hotplug CPUs
    nr_irqs_gsi: 24
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
    PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
    PM: Registered nosave memory: 00000000000d0000 - 00000000000dc000
    PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
    Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
    NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:2 nr_node_ids:1
    PERCPU: Embedded 25 pages at ffff880001010000, static data 72352 bytes
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515025
    Kernel command line: root=/dev/sda5 vga=0x0361 ro
    Initializing CPU#0
    NR_IRQS:768
    PID hash table entries: 4096 (order: 12, 32768 bytes)
    Extended CMOS year: 2000
    Fast TSC calibration using PIT
    Detected 1994.610 MHz processor.
    Console: colour dummy device 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    Checking aperture...
    No AGP bridge found
    Calgary: detecting Calgary via BIOS EBDA area
    Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    Memory: 2053736k/2095936k available (3409k kernel code, 452k absent, 41160k reserved, 1239k data, 464k init)
    SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    hpet clockevent registered
    HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    Calibrating delay loop (skipped), value calculated using timer frequency.. 3990.43 BogoMIPS (lpj=6648700)
    Security Framework initialized
    Mount-cache hash table entries: 256
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 4096K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    CPU0: Thermal monitoring enabled (TM2)
    using mwait in idle threads.
    ACPI: Core revision 20090320
    Setting APIC routing to flat
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a
    Booting processor 1 APIC 0x1 ip 0x6000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 3991.23 BogoMIPS (lpj=6649976)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 4096K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU1: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
    CPU1: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a
    checking TSC synchronization [CPU#0 -> CPU#1]: passed.
    Brought up 2 CPUs
    Total of 2 processors activated (7982.67 BogoMIPS).
    CPU0 attaching sched-domain:
    domain 0: span 0-1 level MC
    groups: 0 1
    CPU1 attaching sched-domain:
    domain 0: span 0-1 level MC
    groups: 1 0
    net_namespace: 1888 bytes
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    ACPI: bus type pci registered
    PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
    PCI: MCFG area at e0000000 reserved in E820
    PCI: Using MMCONFIG at e0000000 - efffffff
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI: BIOS _OSI(Linux) query ignored
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: EC: GPE storm detected, transactions will use polling mode
    ACPI: EC: missing confirmations, switch off interrupt mode.
    [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
    ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in poll mode
    ACPI: No dock devices found.
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:01.0: PME# disabled
    pci 0000:00:1a.0: reg 20 io port: [0x1800-0x181f]
    pci 0000:00:1a.1: reg 20 io port: [0x1820-0x183f]
    pci 0000:00:1a.7: reg 10 32bit mmio: [0xfc404800-0xfc404bff]
    pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1a.7: PME# disabled
    pci 0000:00:1b.0: reg 10 64bit mmio: [0xfc400000-0xfc403fff]
    pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1b.0: PME# disabled
    pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.0: PME# disabled
    pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.1: PME# disabled
    pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.2: PME# disabled
    pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.4: PME# disabled
    pci 0000:00:1d.0: reg 20 io port: [0x1840-0x185f]
    pci 0000:00:1d.1: reg 20 io port: [0x1860-0x187f]
    pci 0000:00:1d.2: reg 20 io port: [0x1880-0x189f]
    pci 0000:00:1d.7: reg 10 32bit mmio: [0xfc404c00-0xfc404fff]
    pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1d.7: PME# disabled
    pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
    pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
    pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
    pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
    pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
    pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
    pci 0000:00:1f.1: reg 20 io port: [0x18a0-0x18af]
    pci 0000:00:1f.2: reg 10 io port: [0x18d8-0x18df]
    pci 0000:00:1f.2: reg 14 io port: [0x18cc-0x18cf]
    pci 0000:00:1f.2: reg 18 io port: [0x18d0-0x18d7]
    pci 0000:00:1f.2: reg 1c io port: [0x18c8-0x18cb]
    pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
    pci 0000:00:1f.2: reg 24 32bit mmio: [0xfc404000-0xfc4047ff]
    pci 0000:00:1f.2: PME# supported from D3hot
    pci 0000:00:1f.2: PME# disabled
    pci 0000:00:1f.3: reg 10 32bit mmio: [0x000000-0x0000ff]
    pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f]
    pci 0000:01:00.0: reg 10 32bit mmio: [0xce000000-0xceffffff]
    pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
    pci 0000:01:00.0: reg 1c 64bit mmio: [0xcc000000-0xcdffffff]
    pci 0000:01:00.0: reg 24 io port: [0x2000-0x207f]
    pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
    pci 0000:00:01.0: bridge io port: [0x2000-0x2fff]
    pci 0000:00:01.0: bridge 32bit mmio: [0xcc000000-0xceffffff]
    pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
    pci 0000:00:1c.0: bridge io port: [0x3000-0x3fff]
    pci 0000:00:1c.0: bridge 32bit mmio: [0xf6000000-0xf7ffffff]
    pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf0000000-0xf1ffffff]
    pci 0000:00:1c.1: bridge io port: [0x4000-0x4fff]
    pci 0000:00:1c.1: bridge 32bit mmio: [0xf8000000-0xf9ffffff]
    pci 0000:00:1c.1: bridge 64bit mmio pref: [0xf2000000-0xf3ffffff]
    pci 0000:06:00.0: reg 10 32bit mmio: [0xfa000000-0xfa000fff]
    pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
    pci 0000:06:00.0: PME# disabled
    pci 0000:00:1c.2: bridge io port: [0x5000-0x5fff]
    pci 0000:00:1c.2: bridge 32bit mmio: [0xfa000000-0xfbffffff]
    pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf4000000-0xf5ffffff]
    pci 0000:08:00.0: reg 10 64bit mmio: [0xfc000000-0xfc003fff]
    pci 0000:08:00.0: reg 18 io port: [0x6000-0x60ff]
    pci 0000:08:00.0: supports D1 D2
    pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:08:00.0: PME# disabled
    pci 0000:00:1c.4: bridge io port: [0x6000-0x6fff]
    pci 0000:00:1c.4: bridge 32bit mmio: [0xfc000000-0xfc0fffff]
    pci 0000:09:03.0: reg 10 32bit mmio: [0xfc100000-0xfc100fff]
    pci 0000:09:03.0: supports D1 D2
    pci 0000:09:03.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:09:03.0: PME# disabled
    pci 0000:09:03.1: reg 10 32bit mmio: [0xfc102000-0xfc1027ff]
    pci 0000:09:03.1: reg 14 32bit mmio: [0xfc104000-0xfc107fff]
    pci 0000:09:03.1: supports D1 D2
    pci 0000:09:03.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:09:03.1: PME# disabled
    pci 0000:09:03.2: reg 10 32bit mmio: [0xfc101000-0xfc101fff]
    pci 0000:09:03.2: supports D1 D2
    pci 0000:09:03.2: PME# supported from D0 D1 D2 D3hot
    pci 0000:09:03.2: PME# disabled
    pci 0000:00:1e.0: transparent bridge
    pci 0000:00:1e.0: bridge 32bit mmio: [0xfc100000-0xfc1fffff]
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
    ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
    ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
    ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
    PCI: Using ACPI for IRQ routing
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    Switched to high resolution mode on CPU 0
    Switched to high resolution mode on CPU 1
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 10 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
    system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
    system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
    system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
    system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
    system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
    system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
    system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
    system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
    system 00:06: ioport range 0x680-0x69f has been reserved
    system 00:06: ioport range 0x800-0x80f has been reserved
    system 00:06: ioport range 0x1000-0x107f has been reserved
    system 00:06: ioport range 0x1180-0x11bf has been reserved
    system 00:06: ioport range 0x1640-0x164f has been reserved
    system 00:06: ioport range 0xfe00-0xfe7f has been reserved
    system 00:06: ioport range 0xfe80-0xfeff has been reserved
    pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
    pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:01.0: IO window: 0x2000-0x2fff
    pci 0000:00:01.0: MEM window: 0xcc000000-0xceffffff
    pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
    pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
    pci 0000:00:1c.0: IO window: 0x3000-0x3fff
    pci 0000:00:1c.0: MEM window: 0xf6000000-0xf7ffffff
    pci 0000:00:1c.0: PREFETCH window: 0x000000f0000000-0x000000f1ffffff
    pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04
    pci 0000:00:1c.1: IO window: 0x4000-0x4fff
    pci 0000:00:1c.1: MEM window: 0xf8000000-0xf9ffffff
    pci 0000:00:1c.1: PREFETCH window: 0x000000f2000000-0x000000f3ffffff
    pci 0000:00:1c.2: PCI bridge, secondary bus 0000:06
    pci 0000:00:1c.2: IO window: 0x5000-0x5fff
    pci 0000:00:1c.2: MEM window: 0xfa000000-0xfbffffff
    pci 0000:00:1c.2: PREFETCH window: 0x000000f4000000-0x000000f5ffffff
    pci 0000:00:1c.4: PCI bridge, secondary bus 0000:08
    pci 0000:00:1c.4: IO window: 0x6000-0x6fff
    pci 0000:00:1c.4: MEM window: 0xfc000000-0xfc0fffff
    pci 0000:00:1c.4: PREFETCH window: disabled
    pci 0000:09:03.0: CardBus bridge, secondary bus 0000:0a
    pci 0000:09:03.0: IO window: 0x007000-0x0070ff
    pci 0000:09:03.0: IO window: 0x007400-0x0074ff
    pci 0000:09:03.0: PREFETCH window: 0x88000000-0x8bffffff
    pci 0000:09:03.0: MEM window: 0x90000000-0x93ffffff
    pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09
    pci 0000:00:1e.0: IO window: 0x7000-0x7fff
    pci 0000:00:1e.0: MEM window: 0xfc100000-0xfc1fffff
    pci 0000:00:1e.0: PREFETCH window: 0x00000088000000-0x0000008bffffff
    pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:01.0: setting latency timer to 64
    pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    pci 0000:00:1c.0: setting latency timer to 64
    pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:1c.1: setting latency timer to 64
    pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    pci 0000:00:1c.2: setting latency timer to 64
    pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    pci 0000:00:1c.4: setting latency timer to 64
    pci 0000:00:1e.0: setting latency timer to 64
    pci 0000:09:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci_bus 0000:00: resource 0 io: [0x00-0xffff]
    pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
    pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
    pci_bus 0000:01: resource 1 mem: [0xcc000000-0xceffffff]
    pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
    pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
    pci_bus 0000:02: resource 1 mem: [0xf6000000-0xf7ffffff]
    pci_bus 0000:02: resource 2 pref mem [0xf0000000-0xf1ffffff]
    pci_bus 0000:04: resource 0 io: [0x4000-0x4fff]
    pci_bus 0000:04: resource 1 mem: [0xf8000000-0xf9ffffff]
    pci_bus 0000:04: resource 2 pref mem [0xf2000000-0xf3ffffff]
    pci_bus 0000:06: resource 0 io: [0x5000-0x5fff]
    pci_bus 0000:06: resource 1 mem: [0xfa000000-0xfbffffff]
    pci_bus 0000:06: resource 2 pref mem [0xf4000000-0xf5ffffff]
    pci_bus 0000:08: resource 0 io: [0x6000-0x6fff]
    pci_bus 0000:08: resource 1 mem: [0xfc000000-0xfc0fffff]
    pci_bus 0000:09: resource 0 io: [0x7000-0x7fff]
    pci_bus 0000:09: resource 1 mem: [0xfc100000-0xfc1fffff]
    pci_bus 0000:09: resource 2 pref mem [0x88000000-0x8bffffff]
    pci_bus 0000:09: resource 3 io: [0x00-0xffff]
    pci_bus 0000:09: resource 4 mem: [0x000000-0xffffffffffffffff]
    pci_bus 0000:0a: resource 0 io: [0x7000-0x70ff]
    pci_bus 0000:0a: resource 1 io: [0x7400-0x74ff]
    pci_bus 0000:0a: resource 2 pref mem [0x88000000-0x8bffffff]
    pci_bus 0000:0a: resource 3 mem: [0x90000000-0x93ffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
    TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    Unpacking initramfs...
    Freeing initrd memory: 2743k freed
    Simple Boot Flag at 0x36 set to 0x1
    Scanning for low memory corruption every 60 seconds
    audit: initializing netlink socket (disabled)
    type=2000 audit(1249997463.944:1): initialized
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    msgmni has been set to 4017
    alg: No test for stdrng (krng)
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:01:00.0: Boot video device
    pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
    pcieport-driver 0000:00:01.0: setting latency timer to 64
    pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
    pcieport-driver 0000:00:1c.0: setting latency timer to 64
    pcieport-driver 0000:00:1c.1: irq 26 for MSI/MSI-X
    pcieport-driver 0000:00:1c.1: setting latency timer to 64
    pcieport-driver 0000:00:1c.2: irq 27 for MSI/MSI-X
    pcieport-driver 0000:00:1c.2: setting latency timer to 64
    pcieport-driver 0000:00:1c.4: irq 28 for MSI/MSI-X
    pcieport-driver 0000:00:1c.4: setting latency timer to 64
    vesafb: framebuffer at 0xcd000000, mapped to 0xffffc20010100000, using 8000k, total 14336k
    vesafb: mode is 1280x800x32, linelength=5120, pages=1
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    Console: switching to colour frame buffer device 160x50
    fb0: VESA VGA frame buffer device
    Linux agpgart interface v0.103
    Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    input: Macintosh mouse button emulation as /devices/virtual/input/input0
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    i8042.c: Detected active multiplexing controller, rev 1.1.
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX0 port at 0x60,0x64 irq 12
    serio: i8042 AUX1 port at 0x60,0x64 irq 12
    serio: i8042 AUX2 port at 0x60,0x64 irq 12
    serio: i8042 AUX3 port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    registered taskstats version 1
    Initalizing network drop monitor service
    Freeing unused kernel memory: 464k freed
    SCSI subsystem initialized
    libata version 3.00 loaded.
    pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    pata_acpi 0000:00:1f.1: setting latency timer to 64
    pata_acpi 0000:00:1f.1: PCI INT A disabled
    ahci 0000:00:1f.2: version 3.0
    ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
    ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
    ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
    ahci 0000:00:1f.2: setting latency timer to 64
    scsi0 : ahci
    scsi1 : ahci
    scsi2 : ahci
    ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 29
    ata2: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 29
    ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 29
    input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata2: SATA link down (SStatus 0 SControl 300)
    ata3: SATA link down (SStatus 0 SControl 300)
    ata1.00: ACPI cmd ef/90:03:00:00:00:a0 succeeded
    ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
    ata1.00: ATA-7: FUJITSU MHV2200BT, 0000004F, max UDMA/100
    ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32)
    ata1.00: ACPI cmd ef/90:03:00:00:00:a0 succeeded
    ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
    ata1.00: configured for UDMA/100
    scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2200B 0000 PQ: 0 ANSI: 5
    ata_piix 0000:00:1f.1: version 2.13
    ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    ata_piix 0000:00:1f.1: setting latency timer to 64
    scsi3 : ata_piix
    scsi4 : ata_piix
    ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
    ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
    ata4.00: ATAPI: MATSHITABD-MLT UJ-220V, 1.00, max UDMA/33
    ata4.00: configured for UDMA/33
    scsi 3:0:0:0: CD-ROM MATSHITA BD-MLT UJ-220V 1.00 PQ: 0 ANSI: 5
    Driver 'sd' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors: (200 GB/186 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
    sd 0:0:0:0: [sda] Attached SCSI disk
    device-mapper: uevent: version 1.0.3
    device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected]
    Intel AES-NI instructions are not detected.
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with writeback data mode.
    rtc_cmos 00:07: RTC can wake from S4
    rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    udev: starting version 141
    sky2 driver version 1.22
    sky2 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    sky2 0000:08:00.0: setting latency timer to 64
    sky2 0000:08:00.0: Yukon-2 FE chip revision 1
    sky2 0000:08:00.0: irq 30 for MSI/MSI-X
    sky2 eth0: addr 00:13:a9:c1:09:33
    cfg80211: Calling CRDA to update world regulatory domain
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    scsi 3:0:0:0: Attached scsi generic sg1 type 5
    ACPI: AC Adapter [ADP1] (on-line)
    input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
    ACPI: Lid Switch [LID0]
    input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
    ACPI: Power Button [PWRB]
    ACPI: SSDT 000000007fedb8e7 0027A (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI: SSDT 000000007fedb3b8 004AA (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI Warning (processor_throttling-0843): Invalid throttling state, reset [20090320]
    Monitor-Mwait will be used to enter C-1 state
    Monitor-Mwait will be used to enter C-2 state
    Monitor-Mwait will be used to enter C-3 state
    Marking TSC unstable due to TSC halts in idle
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    processor ACPI_CPU:00: registered as cooling_device0
    ACPI: Processor [CPU0] (supports 8 throttling states)
    ACPI: SSDT 000000007fedbb61 000C8 (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI: SSDT 000000007fedb862 00085 (v01 Sony VAIO 20070418 PTL 20050624)
    ACPI Warning (processor_throttling-0843): Invalid throttling state, reset [20090320]
    ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
    processor ACPI_CPU:01: registered as cooling_device1
    ACPI: Processor [CPU1] (supports 8 throttling states)
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [TZ00] (58 C)
    input: PC Speaker as /devices/platform/pcspkr/input/input4
    sony-laptop: Sony Notebook Control Driver v0.6.
    input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:29/SNY5001:00/input/input5
    input: Sony Vaio Jogdial as /devices/virtual/input/input6
    ACPI: Invalid active0 threshold
    iTCO_vendor_support: vendor-support=0
    thermal LNXTHERM:02: registered as thermal_zone1
    ACPI: Thermal Zone [TZ01] (58 C)
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ACPI: Battery Slot [BAT0] (battery present)
    i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    ehci_hcd 0000:00:1a.7: setting latency timer to 64
    ehci_hcd 0000:00:1a.7: EHCI Host Controller
    ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1a.7: debug port 1
    ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
    ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc404800
    ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 4 ports detected
    ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    ehci_hcd 0000:00:1d.7: setting latency timer to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc404c00
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 6 ports detected
    uhci_hcd: USB Universal Host Controller Interface driver
    uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    uhci_hcd 0000:00:1a.0: setting latency timer to 64
    uhci_hcd 0000:00:1a.0: UHCI Host Controller
    uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    uhci_hcd 0000:00:1a.1: setting latency timer to 64
    uhci_hcd 0000:00:1a.1: UHCI Host Controller
    uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
    usb usb6: configuration #1 chosen from 1 choice
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    uhci_hcd 0000:00:1d.2: setting latency timer to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
    usb usb7: configuration #1 chosen from 1 choice
    hub 7-0:1.0: USB hub found
    hub 7-0:1.0: 2 ports detected
    input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input7
    input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input8
    usb 1-2: new high speed USB device using ehci_hcd and address 2
    usb 1-2: configuration #1 chosen from 1 choice
    usb 2-3: new high speed USB device using ehci_hcd and address 3
    nvidia: module license 'NVIDIA' taints kernel.
    Disabling lock debugging due to kernel taint
    iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
    iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
    iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    yenta_cardbus 0000:09:03.0: CardBus bridge found [104d:9005]
    yenta_cardbus 0000:09:03.0: Using CSCINT to route CSC interrupts to PCI
    yenta_cardbus 0000:09:03.0: Routing CardBus interrupts to PCI
    yenta_cardbus 0000:09:03.0: TI: mfunc 0x01121b22, devctl 0x64
    usb 2-3: configuration #1 chosen from 1 choice
    nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    nvidia 0000:01:00.0: setting latency timer to 64
    NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.31 Tue Jul 28 17:52:27 PDT 2009
    yenta_cardbus 0000:09:03.0: ISA IRQ mask 0x0cf8, PCI irq 16
    yenta_cardbus 0000:09:03.0: Socket status: 30000006
    pci_bus 0000:09: Raising subordinate bus# of parent bus (#09) from #0a to #0d
    yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge I/O window: 0x7000 - 0x7fff
    yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge Memory window: 0xfc100000 - 0xfc1fffff
    yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
    iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
    iwl3945: Copyright(c) 2003-2009 Intel Corporation
    iwl3945 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    iwl3945 0000:06:00.0: setting latency timer to 64
    ohci1394 0000:09:03.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Driver 'sr' needs updating - please use bus_type methods
    sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 3:0:0:0: Attached scsi CD-ROM sr0
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[fc102000-fc1027ff] Max Packet=[2048] IR/IT contexts=[4/8]
    tifm_7xx1 0000:09:03.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    HDA Intel 0000:00:1b.0: setting latency timer to 64
    hub 2-0:1.0: unable to enumerate USB device on port 5
    iwl3945 0000:06:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
    iwl3945 0000:06:00.0: Detected Intel Wireless WiFi Link 3945ABG
    iwl3945 0000:06:00.0: irq 31 for MSI/MSI-X
    Initializing USB Mass Storage driver...
    scsi5 : SCSI emulation for USB Mass Storage devices
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    usb-storage: device found at 3
    usb-storage: waiting for device to settle before scanning
    input: HDA Intel Mic at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/input/input9
    input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/input/input10
    usb 5-1: new low speed USB device using uhci_hcd and address 2
    usbcore: registered new interface driver hiddev
    Linux video capture interface: v2.00
    input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/2-3:1.1/input/input11
    generic-usb 0003:1058:1102.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-3/input1
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    uvcvideo: Found UVC 1.00 device <unnamed> (05ca:1837)
    uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
    uvcvideo: Failed to query (129) UVC probe control : -32 (exp. 26).
    uvcvideo: Failed to initialize the device (-5).
    usbcore: registered new interface driver uvcvideo
    USB Video Class driver (v0.1.0)
    phy0: Selected rate control algorithm 'iwl-3945-rs'
    usb 5-1: configuration #1 chosen from 1 choice
    input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input12
    generic-usb 0003:046D:C518.0002: input,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1/input0
    input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input13
    generic-usb 0003:046D:C518.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1/input1
    fuse init (API version 7.11)
    vboxdrv: Trying to deactivate the NMI watchdog permanently...
    vboxdrv: Successfully done.
    vboxdrv: Found 2 processor cores.
    VBoxDrv: dbg - g_abExecMemory=ffffffffa0f05760
    vboxdrv: fAsync=0 offMin=0x1ae offMax=0x125c
    vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
    vboxdrv: Successfully loaded version 3.0.4 (interface 0x000e0000).
    VBoxNetFlt: dbg - g_abExecMemory=ffffffffa10a9f00
    hub 2-0:1.0: unable to enumerate USB device on port 5
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460302564f69]
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    Clocksource tsc unstable (delta = -435934901 ns)
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    EXT3 FS on dm-0, internal journal
    scsi 5:0:0:0: Direct-Access WD My Book 1028 PQ: 0 ANSI: 4
    sd 5:0:0:0: Attached scsi generic sg2 type 0
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
    sd 5:0:0:0: [sdb] Write Protect is off
    sd 5:0:0:0: [sdb] Mode Sense: 10 00 00 00
    sd 5:0:0:0: [sdb] Assuming drive cache: write through
    usb-storage: device scan complete
    sd 5:0:0:0: [sdb] Assuming drive cache: write through
    sdb: sdb1
    sd 5:0:0:0: [sdb] Attached SCSI disk
    EXT4-fs: barriers enabled
    kjournald2 starting: pid 1929, dev dm-1:8, commit interval 5 seconds
    EXT4 FS on dm-1, internal journal on dm-1:8
    EXT4-fs: delayed allocation enabled
    EXT4-fs: file extents enabled
    EXT4-fs: mballoc enabled
    EXT4-fs: mounted filesystem dm-1 with ordered data mode
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    Adding 2449872k swap on /dev/sda6. Priority:-1 extents:1 across:2449872k
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    iwl3945 0000:06:00.0: firmware: requesting iwlwifi-3945-2.ucode
    hub 2-0:1.0: unable to enumerate USB device on port 5
    iwl3945 0000:06:00.0: loaded firmware version 15.32.2.9
    Registered led device: iwl-phy0::radio
    Registered led device: iwl-phy0::assoc
    Registered led device: iwl-phy0::RX
    Registered led device: iwl-phy0::TX
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    wlan0: authenticate with AP 00:11:6b:10:2f:bc
    wlan0: authenticated
    wlan0: associate with AP 00:11:6b:10:2f:bc
    wlan0: RX AssocResp from 00:11:6b:10:2f:bc (capab=0x471 status=0 aid=1)
    wlan0: associated
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    hub 2-0:1.0: unable to enumerate USB device on port 5
    i think the result is, that my bluetooth and webcam isn't working...
    can you help me pls.
    regards nigg
    Last edited by nigg (2009-08-11 14:14:57)

    I'm also having this problem. It's happening with my USB flash disk. I was almost buying another one when I tried it with Windows Vista on the same machine and it worked ok, then I tried Arch Linux (with kernel 2.6.30.5) on another machine and got the same error. After that I tried Ubuntu and it worked ok. Seems that Arch's kernel doesn't like my USB flash disk.
    Last edited by esdrasbeleza (2009-09-02 01:16:09)

Maybe you are looking for

  • Unique Audio Challenge - Which Application Should I Use?

    I have audio that was transferred into MP3 format. But there's a big problem. There are two separate channels on each MP3 stereo channel. The left channel is one recording, the right channel is another. I need to separate them into individual MP3s. A

  • How fo I get rid of the WindowShopper add-on?

    I have an add-on called "WindowShopper" that somehow recently turned up in Firefox (v20.0, Mac OS X 10.7.5). I don't know how it got into Firefox -- *I* certainly didn't add it -- and I can't find it anywhere in "Tools > Add-Ons," "Extensions," "Pref

  • IPad Operating System and iTunes libraries consolidation

    Two missions: First trying to consolidate multiple libraries within my family.  Have iTunes on laptop (windows xp) with 55GB of music on it which is sync'ed with sons iPod and my iPod.  Also have a iPad which my husband has bought a good amount of mu

  • WebDynpro Content Administration

    Hi, My requirement is that I have to give WebDynpro Content Administration Page access to one of my developer. But I dont want him to Get Content/System/User Admin Role. I cleared all his roles and attached his ID to Administrator GROUP. It gave him

  • Pavilion dv6700 shuts down durring start up

    My Pavilion dv6700 laptop will not power up.  When I press the power button the bios screen comes up then the laptop shuts down.  I was having problems with overheating and now think the processor may have overheated one too many times.  How do I kno