USB Driver for LabVIEW

I want to transfer data from PC to my own Hardware. This transfer sould
made via USB.
So I need a driver for USB or I must develope one. But I have no idea
how!
Can you give me some hints how I can begin to develope a driver in
LabVIEW.
Thanks for your answers
Peter

A good place to start looking for general information on driver development
is NI's Knowlege Base.
You can try the following links:
http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/98e85eb00f
e934f08525645d0073ee1a?OpenDocument
http://digital.ni.com/appnotes.nsf/websearch/6ce91ae5067142e4862563df001ab07
4?OpenDocument
Regards,
Alan Brause
pmaigler wrote in message
news:[email protected]..
> I want to transfer data from PC to my own Hardware. This transfer sould
> made via USB.
>
> So I need a driver for USB or I must develope one. But I have no idea
> how!
>
> Can you give me some hints how I can begin to develope a driver in
> LabVIEW.
>
> Thanks for your answers
> Peter
>

Similar Messages

HP 54501A - Instrument Driver for LabView v.7 or v.8

Hi all,
I'm looking for HP 54501A - Instrument Driver for LabView v.7 or v.8. I have NI gpib/usb controller installed, but cannot control the scope via Labveiw.
The link I found at NI web site within drivers section seems to be broken so I couldn't download it!
Please, anyone, suggest/help!

The link you were given works for me. You can try it again. The given link brings you to a page where the CVI and LabVIEW drivers are listed. the direct link to the LabVIW driver is http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9455659CE034080020E748... .

Is it possible to have two USB drives for the IPad? I want to bring RAW photo files from my camera, through the IPad and back to an external hard drive. One of my cameras does not use an SD card. How can I do this?

Is it possible to have two USB drives for the IPad? I want to bring RAW files from my camera through the IPad and out to an external hard drive. One of my cameras has an SD card but the other one doesn't have a card that would fit in any of the camera devices I've seen on line. Realted to this, I bought the IPad camera accessory. Can I put the SD card in the device and also hook the external hard drive to the USB port of the accessory and download from the camera to the hard drive? Can I put Lightroom or the Nikon photo editing software on the IPad? Right now I carry a PC laptop and external hard drives with me on wildernes trips. Internet and WiFi are not available. Because I shoot so many photos and they're in RAW I need to download from the camera to the external drive because I run out of memory on the PC (and it has much more memory than the IPad). I have Nikon NX software and lightroom on my PC. I'd love to be able to reduce the weight I carry by using the IPad to edit my photos each night while on trips. Is this possible and how would I do it? I'd appreciate any guidance.

No, the camera connection kit only supports the copying of photos and videos to the Photos app, it doesn't support copying content off the iPad. For your second camera instead of the SD reader part of the kit, does the iPad to camera cable not work with it for direct transfer to the iPad ?
For Lightroom and Nikon software again no - you can only install apps that are available in the iTunes app store on your computer and the App Store app on the iPad, 'normal' PC and Mac (OS X) software are not compatible with the iPad (iOS). There are some apps that perform fairly basic editing functions that are available in the store, but nothing as sophisticated as, for example, Lightroom.

I would like to take a iTunes play list and put it on a USB drive for my car radio to stay in my car. Is there a way to do this through iTunes so you have all the song info and there's no number in front of the name of the song? Is there a program?

I would like to take a iTunes play list and put it on a USB drive for my car radio to stay in my car. Is there a way to do this through iTunes so you have all the song info and there's no number in front of the name of the song? Is there a program?

iTunes only syncs to Apple devices.
Assuming the media is not DRM protected, any of the media can be dragged and dropped from iTunes onto other drives (external, flash, etc) as the user chooses.

Hp driver for labview for hp8156a attenuator

I am looking for a hp8156a driver for labview. There is not one posted in the driver section of this site. Thanks

Here is a link to the programming manual. Section 8 shows the commands. It will take some work, but you can write your own drivers.
http://www.home.agilent.com/upload/cmc_upload/All/opat0500.pdf
Message Edited by unclebump on 07-12-2005 04:21 PM

I am confused by the installation step that requires you to create a bootable USB drive for windows installation. What is the ISO image and why has it selected my Passport backup drive as the destination disc?

In the bootcamp installation it asks me to create a bootable USB drive for Windows Installation. To do so, I must choose an ISO image. What is that? When I click "choose" I don't understand the options presented. Is this the destination of the partition or where Windows will reside on the Mac? Why does it also indicate the the destination disk si my WD Passport Back up drive?

OK, so I have an apple superdrive hooked up to my mini (along with my Passport back up drive). I also have the discs for both 64bit and 32bit Windows along with the product key. I am still not sure what to do when faced with the options after "choose".

Need SPARTAN 3E board Driver for Labview FPGA 8.5 !!!!!! Thx

HI!!I need the spartan 3e driver for labview 8.5(not for labview 8.6) for school useI try to download it from ftp://ftp.ni.com/outgoing/NISPARTAN3ELV85.zip
but this link is dead now. Could somebody send this driver to [email protected] PLZ? Thank you a lot for all in advance
Solved!
Go to Solution.

Hello,
I'm looking for same (Labview FPGA 8.5 for Spartan 3E). But it isn't available on related url now. I'll be glad if someone can help to find driver.
Best regards,

IS CLIP supported by Xilinx Spartan3E driver for LabVIEW 8.6?

IS CLIP supported by Xilinx Spartan3E driver for LabVIEW 8.6?
For HDL interface node, the enable chain and multi clock domain is difficult to understand
Solved!
Go to Solution.

Reidl,
Thank you for your answer. How do I uninstall my current version? I have looked in "Add or Remove Programs," but I don't see anything under "Xilinx" or "Spartan." I do see an entry for "National Instruments Software." However, when I click "Change / Remove" I don't see any entries for the Spartan Board.
I tried running the installation program, and I received the following message:
The NI LabVIEW FPGA Support for Spartan-3E 1.1.0 installation has failed with the following error.
You have a higher version of NI LabVIEW FPGA Support for Spartan-3E in your system. You must uninstall it before installing this again.
What is the latest version number? How do I check what version I currently have?
Thanks,
James Carroll

Is there compatible motion driver for LabVIEW 8.6?

Is there compatible motion driver for LabVIEW 8.6? The latest motion driver seems to be 7.6 and it only support up to LabVIEW 8.5...

If you buy LabVIEW 8.6, you will also get 2008 August Driver CD.
NI-Motion 7.7 driver should be included in it.
Or you can wait for a while.
I guess NI will put on Web these days.

Aeroflex 2975 driver for LabVIEW 8.0

Is there a way to convert the Aeroflex IFR 2975 driver for LabVIEW CVI for use in LabVIEW 8.0? OR, is there a driver already developed for this?

Frank,
I am using the LV 7.1.1 version of this CVI driver in an application I wrote. We should be able to recompile this for 8.0. Basically as I explained with no handshaking the instrument falls out of sync with the controlling computer. Basically the only GPIB command that is supported in that driver is *IDN?. So what I have done is after other calls I use this command and compare the return string to see if it is what I expected. If not I use a popup telling the operator that a GPIB error occurred and to reboot the IFR to clear the bus. I also have instructed the operator to run NI Spy in the background...this seems to cut down the occurance of these errors. Another way to clear the bus that is faster and usually works is to stop the application, and read the bus using MAX until you see a timeout when there is no more data available( usually twice). Then rerun the application. Depending on the application this might be a work around though not an elegant one.
Since the driver was converted from a CVI driver it uses the call library function node. This does not allow us to control the timing between the Write functions and Read functions. If you are doing something that is relatively simple you could use the TCL command set and VISA to write a driver. Just put a wait function between the Write and Read function and experiment with the timing until it looks like it won't fail. I've considered doing this myself but have been hoping that they will actually make the instrument 488.2 compliant. I am assuming that the actual error is that the data buffer is being read by the controller before the instrument is finished writing to it. The other scenario is that the data buffer might not actually be getting flushed every time it is read. I'm hoping my first assumption is correct or they have even more problems with the instrument.
In January of '05' they actually enabled the following commands *SRE xx, *SRE? and *STB?. I recently wrote a simple vi to see what happens to the Status Byte after using IDN? command and reading the data buffer. The MAV bit begins logic low, then goes hi when the data is available. After reading the data (i.e. "IFR Systems, 2975.....) I again query the Status Byte. The MAV bit is still in a logic hi state. I sent screenshots of the front panel and block diagram as well as the .spy files to them. All was heavily notated and they said they were going to look at it. If anyone is interested in this I can post this code as well.
Using LabVIEW 2010SP1 and TestStand 4.5

Looking for HP 5371A driver for Labview 6.1?

want to communicate with HP5371A by PC over GPIB port

I think that device is too old for finding a driver for labview. If you have all the GPIB command, it's easy to program. I made it for another type of instrument.
Benoit Séguin
Software Designer

Need a HP3421A native driver for labview 5.1

Hi,
I'm looking for a native HP3421A driver for labview 5.1. Of course I searched in the "Instrument Driver Network" but I foundd only drivers for labview 6.0 and 7.0 or greater.
According to this document: http://www.ni.com/pdf/manuals/321691a.pdf#search=%22labview%204.x%20hp3421a%22 there is a such driver for labview 4.x.
Any idea where I could find this driver for labview 5.1 ? A haven't any "Instrument Driver Library CD-ROM".

hi there
the driver he is searching for can be found here (LV 7.0): https://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E969E659CE034080020E74...
the driver uses the old school GBIP functions, so it should be possible to downgrade it down to LV 5.1. do downgrade open the "HP 3421A Example.vi" and choose
File->Save with options->Save for previous.
since you only can downgrade to the next prior version of LV you need a ladder of LV versions, but i'm sure that if you ask here you'll find someone who can do this for you.
Best regards
chris
CL(A)Dly bending G-Force with LabVIEW
famous last words: "oh my god, it is full of stars!"

Where can i download a usb driver for my revere 3 (model

I have been trying to download a usb driver for my new revere 3 so I can connect with my 8.1 windows laptop. anyone have an idea where I can find it? The LG site doesn't list any drivers for it

Mac 101: Printing (OS X Lion)
Important:
Your OS X Lion system will either have the necessary printing software already installed, or it will automatically download and install software when the printer is connected or configured. Do not install software that came with the printer as it may be out of date, and do not connect the printer to your Mac yet. Follow the instructions that came with the printer to unpack, install ink or toner, and insert paper. Finally, use the instructions in this article to connect the printer to your Mac.
The procedures are identical for Mountain Lion.

I want to make a bootable usb drive for my macbook air,and my ystem is osx mountain lion 10.8.5. How can i download it again without repaying for it so i can make my bootable flashdrive? I'm pretty new at this computer stuff so i don't know how things

I want to make a bootable usb drive for my macbook air,and my system is osx mountain lion 10.8.5. How can i download it again without repaying for it so i can make my bootable flashdrive? I'm pretty new at this computer stuff so i don't know how things work.
Message was edited by: tzaphon

This is not difficult and you will not have to download from the app store.
your computer has what is called a recovery partition that came with it.
simply hold cmd+R while you boot up. let go a second after you hear the chime.
you will boot into the recovery partition.
Use disk utlity to format your usb drive and then exit Disk utlity and go to Reinstall Mountain Lion.
it will ask you which disk you want to install ML onto. Choose your new USB drive.
easy peasy

Musicord Cherub MRD-41 Recorder: USB-Driver for Mac

Hello,
I am searching for the USB-Driver for Musicord Cherub MRD-41 Recorder. Searching for it along the internet did not give any matching result.
Originally a CD containing the USB-Driver for Windows was included with the product. Since we now work with Apple-Products this does no longer work. Connecting the device to a Mac (as it is normal these days) and hoping, that it will work without any additional Software does not give any result.
On the Original-CD the manufacturer states, that the USB-Driver for Mac can be downloaded at www.apple.com but there nothing can be found anymore.
The recorder has been bought about 6 years ago (used under Windows then). Now we would like to use it again under Mac-systems (10.6 and 10.7).
Does anyone know, if, and where help can be found?
Thank you very much

If it uses MIDI, Garageband can often read it.

USB Driver for LabVIEW

Similar Messages

Maybe you are looking for