"Use Twain Software" not working

In Image Capture I need to change the device to "Use Twain Software" I believe this should be seen as an option under the menu "Devices" unfortunately this does not appear as an option for me therefore I can't make the change. Can anyone help?

Hi Udo,
I'm using version 2003 of xls.
Yes, I specified that the target is WWV_FLOW_FILES. However, I queried the view and the data was not inserted into it. I'm going to run some tests meanwhile (query the table wwv_flow_file_objects$).
Do I have to configure something else with the file browse besides to set the target to WWV_FLOW_FILES?
Thanks a lot!
--Elena.

Similar Messages

Am getting message that scanner is not compatible with my macbook and to use twain software. Any suggestions?

Need help with downloading driver for scanner . Have HP M1005 MFP. Am getting message to use twain software. Any suggestions?

Your HP M1005 MFP all in one is too old and unsupported for 10.8.5
HP's site says that OS X 10.3 and 10.4 are supported. It does not, repeat, does NOT mention 10.5 much less newer.
Also there is no patch support for same on the last resort:
http://www.sane-project.org/sane-mfgs.html#Z-HEWLETT-PACKARD
Nothing on earth is as aggravating as twain drivers for scanners. Ive installed every make and model on PC and Mac, and theyre all hair-pulling-worthy.

When i install the new os my fcp,motion and many adobe software not working so please help me out.

when i install the new os my fcp,motion and many adobe software not working so please help me out.
there are so many videos on youtube but i want know any solution from apple side plz my so many works are pending becuze i am working as Video Editor.

You need to be more specific about which software applications you're using, the versions and what happens when you try to open them.
It would also be nice if you could include which model MacBook Air you're using.
Clinton
MacBook Pro (15” Late 2011), OS X Yosemite 10.10, 16GB Crucial RAM, 960GB M500 Crucial SSD, 27” Apple Thunderbolt Display

Beats Audio Control Panel software not working after Windows 10 upgrade.

Beats Audio Control Panel software not working after Windows 10 upgrade. the Beats sound enhancement is useless in WIndows 10. When opening the Windows 10 sound properties I'm getting this box message: Auido enhancement problem Windows has detected the audio enhancement for the following device are causing problems: Speakers / Headphones (IDT High Definition Audio Codec) Woud you like to disable driver enhancement for this device? IDT High Definition Audio CodecBeats Audio Control Panel version6.10.6491.02013.11.2009:43:18 Please provide some kind of fix for this?

Well, it has been a long road on the Win 10 upgrade. At first I got the same error message as above, but after deleting the Dolby Advanced Audio v2 in Win 10 using Control Panel Programs and Features and rebooting, I got into the continual BSOD upon reboot. Here are the steps I took to at least get stable on Windows 10. First, I rolled back to Windows 8.1 using the advanced feature in the BSOD recovery options. Once back in Win 8.1, I deleted the Dolby Advanced Audio v2 using Add/Remove Programs in Control Panel. Then I downloaded the Win 10 update and re-installed it. Once that completed, I updated the Intel Graphics driver under the display adapters (on my G780 it is an Intel HD Graphics 4000, and the driver can be found at https://downloadcenter.intel.com/). Currently I am running version 10.18.10.4252 for my machine. Then, under the Device Manager, I updated the Conexant SmartAudio HD driver under the Sound, video, and game controllers. That driver is currently at 8.66.4.50 and was automatically downloaded from the web when I requested to update driver. I also changed several others settings such as Notify to schedule restart after updates are installed instead of automatic (under Settings --> Update & Security --> Advanced Options) and Do you want Windows to download driver software and realistic icons for your devices? --> No, let me choose what to do, never install driver software from Windows Update. After that, I shut down the machine, waited a moment and booted back up. I have no idea why this helped or if it is overkill, but I am stable and running without a fear of rebooting now. Hope this helps if someone else is having this same issue.

Can use another software (not FMLE) to publish stream to FMS?

Hi all,
I have a question:
Can use another software (not FMLE) to publish stream to FMS?
I ask this question because I want to use Authentication add-in to prevent user publish stream to FMS. This add-in only affect with FMLE, so, if user use another encoder software, they still can publish stream to my FMS

You can use any encoder to publish to FMS - you can write you own add-in to restrict any publisher - but you are right that FMLE add-in will work only for FMLE.
Actually i am not clear with your questions - Are you concerned that other publishers apart from FMLE would publish or you want add-in for other encoders - meaning do you plan to use another encoder?
If its first problem - you can do simple thing - turn SWF verification on - make exception for FMLE and have FMLE add-in - in this case only valid clients would be able to connect - even other encoders wont be able to connect - so if someone cant connect there is no way they can publish.

After installing iPhone Configutilities in my Mac, Personal Hotspot using USB is not working! Please help, I am using 10.7 Lion OS

After installing iPhone Configutilities in my Mac, Personal Hotspot using USB is not working! Please help, I am using 10.7 Lion OS

Did you talk to your carrier?

Multi scanner software not working after E71 FW U...

Multi scanner software not working after E71 FW Update to 3.1

Nice bit of trouble-shooting. Thanks for sharing the final solution.

Windows Server 2012 - Printing using UNC path not working

Hi,
I have a problem printing using the printer's UNC path ("\\Server_Name\Printer_Hostname") to work with a web
app hosted on IIS 8. With a windows forms application the UNC path is working fine and the app prints.
With
the web app I receive an error "The data area passed to a system call is tool small".
Also,
in the event viewer under Applications and Services Logs -> Microsoft -> PrintService -> Operational, I receive the error "The print spooler failed to reopen an existing printer connection because it could not read the configuration information
from the registry key S-1-5-82-1980832875-2702362896-1795126167-3622310632-1152289074\Printers\Connections. The print spooler could not open the registry key. This can occur if the registry key is corrupt or missing, or if the registry recently became unavailable."

I have contacted IIS forum support.
Please review the link: http://forums.iis.net/p/1213109/2079229.aspx?Re+Windows+Server+2012+Printing+using+UNC+path+not+working
Their final response:
Printing from ASP.NET using System.Drawing.Printing itself is a horrible approach, as this namespace was designed for Windows Forms only. The designers did not take everything about ASP.NET in mind, so any issue can happen. That can answer why the HP model
works while the Samsung fails, as the HP one just "happens
to work",
http://msdn.microsoft.com/en-us/library/system.drawing.printing.printdocument.aspx
Similarly, System.Printing was designed just for WPF.
About which printing API to use in ASP.NET/IIS, there is no clear answer so far. Thus, your only resource is Microsoft support, who can perform further analysis (with their dedicate utilities and of course Windows source code) and might come across a solution
to help you out. This is not a trivial scenario.

Where used list is not working for IMG nodes/Document in solar01

hi experts
In template project , we are using same IMG objects in different business processes and subsequent configuration document is attached to each IMG node in configuration tab. ( like same IMG node - define order types used in different business process configuration tab )
when i use " where used list " from the configuration tab , its not showing the IMG objects used in different business processes in the same project. whereas its showing the IMG nodes used in the different project.
I need to find out the same IMG objects/ document used in the same project using the " Where used list " button.
Please provide your answers
Note : we have linked one configuration document to same IMG nodes used in different business. " where used list " also not working for documents as well
Thanks
Sol man

Hello there,
I just tried some tests and couldn't face any problem with locating other usages for the objects in configuration tab.
You mentioned a configuration document, so have in mind that the document usage will only be considered if it is a link to the same document and not just a copy.
e.g:
Here I created a document in this node:
Then I added it as a link here:
and as a copy here:
When I go back to the original node and use the where-used, it'll only show the original and the link:
This happens because after copying a document, it is considered as a new one instead of another usage of the original one.
best regards,
Fabricius

I keep getting a message that my ipad could not be activated because activation server is unavailable and when i try to use itune its not working as well.Plssss help

i keep getting a message that my ipad could not be activated because activation server is unavailable and when i try to use itune its not working as well.Plssss help

Has this iPad ever been jailbroken, had the OS rolled back, or used a beta version?

Device software not working

BB device software not working on windows 7 please help me , i installed last version 7.0,1

In what way does it not work? Without specific details its very hard for anyone to help

Validations using OB28 is not working for GL posting using FB01

Hi Experts,
Validations using OB28 for posting using FB01 is not working.
My requirement is after entering a line items and click post validations should be triggerd.
i want to block a posting based on document type.
i have maintained as below..
Prerequisite.
( BKPF-TCODE = 'FB50' OR BKPF-TCODE = 'FB01' ) AND (
BKPF-BUKRS = '1000' OR BKPF-BUKRS = '0001' OR
BKPF-BUKRS = '0002' ) AND BKPF-BLART = 'XX'.
check.
Used userexit to check sy-ucomm = 'BU' (for posting).
entries are maintained in OB28 for relevant company codes.
it is working for FB50 but not FB01.
same thing i tried to maintain at header level as well as item level. but it is working only for FB50 but for FB01.
Please help me.
Regards.
Venu.

Hi Venu,
Go to GGB0 and expand the navigation till you reach the validation name of line item level and choose menu item *Validation -> Simulate.
Here you can enter the inputs, those you are entering while doing FB01 and execute it.
Then in the results, you will have the log for each step of your total validation of line item level.
Check , whether your questioned STEP's pre requisite is met and check is not fullfilled.
Accordingly you can make the changes to the STEP.
This info may help you.
Regards,
Srinivas

Windows 8.1 and Deskjet 3050 J610 Software not working

New Desktop running WIndows 8.1 and the HP Deskjet 3050 J610 printer/scanner. I can load the drivers to make the printer work but the scanner software is not present.
When I try to open the Scanner Software:
I get the following:
Would like a fix. Been fighting with this for a while.

ClasicD_72,
It appears that one of our Experts is trying to answer your inquiry on another member's Thread on this subject.
I will comment briefly here and then withdraw.
Commentary
After installing the Full Feature Software, at least in many cases involving Windows 8.1 installs of the printer software, you should see a Printer Assistant shortcut on your Desktop. You can use the Printer Assistant to access the Scan to Document or Photo software package.
Although there is a scan program within the hierarchy of many of the Printer software folders, I have not seen an recent instance where the scan program is a stand-alone executable. In other words, you must call the Scan package from a parent program, even assuming you can find a "Scan" program in Bin or another similar folder.
Example:
Click the Kudos Thumbs-Up to show you appreciate the help and time from our Experts.
Although I strive to reflect HP's best practices, I do not work for HP.
Click Accept as Solution when the Answer is a good Fix or Workaround!
Kind Regards,
Dragon-Fur

FingerPrint Sensor/Software not working right with Windows XP Pro SP3

Hi All,
I have a 3 month old Satellite Pro S300-S2504 (2.4 GHz CPU, 3 GB RAM, Bluetooth, firewire - was a custom build with most of the options I could get). The O/S installed was/is Vista Business. It came with a dowgrade XP Pro SP3 disc as well.
I bought a second hard drive - swapped it with the original and installed Windows XP Pro on it - having grown tired of Vista. I don't intend to keep both O/S's - but I didn't want to mess with what I had until I got XP working - and that's the reason I got the second hard drive for XP. Anyway, XP Pro is installed and working except the fingerprint sensor. As soon as I booted for the first time - with nothing but the factory everything installed, it prompted me to register fingers for the sensor. I tried but I got a database not found error followed by a sensor not working error. I got the latest updates for the fingerprint sensor, removed what I had - rebooted and installed the newer program - I got the same error. I then uninstalled the program again, went through the registry and removed all entries whose key had TrueSuite in it, rebooted and installed the latest version again - rebooted - and got the same errors. Looking in Device Manager, the sensor is working fine but once I try to register a finger and it fails, I then look in Device Manager and the sensor has a yellow error indicator. I used System Restore to go back to the original configuration and then tried the Fingerprint drivers/patches for Vista and for Windows 7. All of them installed but I got the same database not found error followed by the fingerprint sensor not working error.
I did end the program, then using Task Manager, I ran the Fingerprint utility as administrator - still got the same errors. I've completely reinstalled from the Windows XP restore CD four times trying to solve this and I can't get the fingerprint reader to register fingerprints - I always get that error.
I have a lot of graphic editing (movies) software as well as file conversion programs and a very stable version of Roxio Easy Media Creator that all works fine in Windows XP - but it all has problems running in Vista and I'm tired of the bugs that Vista seems have - and I want to use Windows XP Pro. I will try any suggestions. The fingerprint sensor and software works reliably in Vista. I even updated it and that went fine. I suspect there's a problem with the XP version of the software for my computer. I did notice that Toshiba doesn't sell the this model series with XP downgrade as an option anymore. I wonder if this is one of the reasons.
Anyway - I would very much appreciate help with this. Any ideas at all are welcome.
Thanks,
Dennis

Satellite Pro M10-S405
..a clean Win XP Pro install and it still doesnt work.There is a Win Xp key on the bottom of the laptop, but I cant seem to use it.
The Product Key that comes with the computer is useless to activate a retail installation. You would need to purchase a new one or convice Microsoft that an old one is no longer in use.
In the device manager it shows
Ethernet Controller
Multimedia Audio Controller
Network Controller
Unknown Device needing Drivers. I have searched and downloaded drivers and installed them but it still doest work.
Get the drivers from here.
Install the chipset utility first, followed by the display driver. Be sure to install the common modules prior to any Toshiba utilities, including power management.
-Jerry

HP Scan 3 software not working with MacOS 10.9 Mavericks

I just bought a new iMac to replace my old iMac and updated toe mew Mac to 10.9 Mavwericks. Now my HP Scan 3 software does not work and there is no update for this software that I can find. Can anyone help getting updated HP scanning software to use with Mavericks. Thank you.

Thanks for your reply. I tried what you suggestsed and it did not work. My printer was listed. The website says it is for MacOS 10.8 and Mavericks is 10.9. My printer prints fine. The problem is with the HP Scan 3 software. When I try to use it I get a dialog box that says check withn the developer as it does not work with my OS. Also, I went to the firm ware updater in my HP utilities folder and trie to run that. I got a message saying that there is no update for my device.
It is hard to believe that HP has not updated the scan software to work with Mavericks.

"Use Twain Software" not working

Similar Messages

Maybe you are looking for