User unable to hear from diferent WLC registered AP

Hi,
We have 2 WLC 4404 and 4402 .Currently around 115 Nos 1242 series AP is registered in both WLC .100 AP is in 4404 and rest in 4402 .Software Version 7.0.251.2 Emergency Image Version 5.2.157.0..We have Cisco 7921 ,7940 and 7911 phone.we have started the 4402 WLC recently with 15 Nos AP.Now we are facing the below mentioned problem
We are unable to hear the sound in call when one wireless phone registed with AP of WLC 4404 and one wireless phone registed with AP of WLC 4402.
But at the same time when weireless pone user call to any wire phone user it's working fine.Both user are able to hear.
Plase help me to resolve the issue.
Regards
Debabrata

Debabrata try the following if virtual ip didn't solve your issue.
1- Keep the Authentication/encryption open
2- Test making call using wireless clients on same WLC 4404 but on different AP
3-If above work then change the WLC but no WLC 4402 any other for testing purpose and test again

Similar Messages

Unable to hear from ear piece

Hi,
I am using Curve 8520. All of sudden I am unable to hear voice from ear piece. When I check my display screen ear piece icon flashes with headset symbol. This continuously happening till I disconnect the call. I have used my headset & I am able to hear loud & clear. I wish I could get some experts assistance on fixing the issue.
Thanks
Surya

Hello!
Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Best!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

User unable to send from additional Mailbox.

Hello all,
Here is the scenario that I am working with:
I have two users: Lucy and Jane. Lucy is Jane's boss, and has given Jane access to her mailbox to send/receive emails while Lucy is busy.
Jane is able to send email on behalf of Lucy as long as she stays logged in to her own account.
However, When logged into Lucy's account (as it was added as an additional profile to Outlook) Jane is unable to send any emails; they all get stuck in the outbox.
Both these users are O365 users, and we have verified that send/receive works in the OWA for both Lucy and Jane.
Jane is using the Outlook 2010 client on a Windows 7 machine.
Any information you could come up with would be of great assistance!

Hi,
If Jane wants to send as Lucy with an additional profile for Lucy account, Jane needs to have Send As permission instead of Send On behalf permission to Lucy's mailbox. To grant send as permission, we can run the following command in EMS:
Add-ADPermission -Identity Lucy -User Jane -ExtendedRights "Send As"
For more information about send as permission, please refer to:
http://technet.microsoft.com/en-us/library/bb676368(v=exchg.141).aspx
Regards,
Winnie Liang
TechNet Community Support
Thank you for the reply.
One thing should be mentioned: When jane is logged into her own profile in Outlook, she is able to send emails from Lucy's email completey fine. When Jane logs into Lucy's profile in Outlook, the emails all get stuck in the outbox.
In terms of the Send As permission, I would assume that Lucy has it as she is able to send email from Lucy's email when logged into Outlook on her own profile.

Unable to Hear from iphone 4 speaker

The speaker of my iphone 4 is not working. i could not be able to hear any sound except the call ringing. i do not hear the sms notifications, whatsapp, or any other application notification even the keyboard typing sound. but i hear everything when i blug the earphone.although when i want to raise or low the sound from sound bottoms the sound volume indecator does not appeared at all.
Any help????

Hello there, Aboud.Rifai.
The following Knowledge Base article offers up some great steps for troubleshooting the issue you're describing:
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/ts5180
Verify that the volume is set to a level you would normally be able to hear.
Ensure that there is nothing plugged in to the headset jack or the dock connector.
If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
If the iPhone is paired with a Bluetooth headset or car kit:
Try turning off Bluetooth.
If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
Restart the iPhone.
If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
If the issue is not resolved, please contact Apple Support.
Learn more about troubleshooting iPhone hardware issues.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Users are unable to print from Adobe Reader X

Hi,
Multiple users in our environment report that they are unable to print from Adobe Reader X. They receive the following error messages (translated from Dutch) Document cannot be printed. There are no pages selected.
We are using Reader version 10.1.3
What we have tried to resolve the issue (without any positive results):
- Repair the installation of Adobe Reader.
- Update Adobe Reader to the latest version for Vista (x86) (10.1.7)
- Created new user profile for the affected users.
The documents can be printed without any errors from Foxit Reader.
At the moment we use the following workaround:
Open the document in Internet Explorer, and then print the document from there.
Does anyone have any idea how we can resolve this?
Best regards,
Duncan

James,
I'm sorry to hear that you were having the same problem under 9.5. I had recently updated to Adobe Reader 10 under Windows 7 and yesterday my "default printer" simply disappeared from the options on my control panel. I re-installed my printer, but today whenever I would open a PDF document and try to print it, the document would simply close with no further ado. After a bit of trial and error, I ended up uninstalling Adobe Reader 10 and going back to Adobe Reader 9.5. Now everything is working just fine.
nlncmjd

I am unable to login from my login page after I restarted my mini mac running snow leopard 10.6 server. I am a new user. Need help

I am unable to login from my login page after I restarted my mini mac running snow leopard 10.6 server. I am a new user. Need help

Try clearing your cache, [https://support.mozilla.org/en-US/kb/How to clear the cache Instructions here]. Then, try going to [https://accounts.google.com Google Accounts]. If there is currently an account singed in, sign out, then back in. After that, try going to Google Adwords.

I carnt hear my message tone,the sounds it makes when the phone locks and opens.Also i am unable to hear my music playing from my phone but my alarm and ringtone are working.Can anyone help

i carnt hear my message tone,the sound it makes when the phone locks and opens,also i am unable to hear music when playing from my phone but my ringtone and alarm tone work.Ive made sure the silent button is not on,and the volume button on the side of the phone is just showing it blank instead of it going up and down.To try and fix this i have reset my settings and restored my phone,but now its just skipping the music i have purchased from itunes when in a docking station which is now another problem i have as well.Can anyone help????

Hello dbrookes,
Thank you for using Apple Support Communities!
It sounds like even though the Mute switch is not on, sounds are not making the, well, sound they should, and the volume buttons make a blank volume indicator appear on the screen that does not show the volume level.
I wanted to recommend a couple of things.
First, I would reset the phone:
Resetting your device
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
From: iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
If that does not resolve the issue, then you may want to try backing up to iTunes, and restoring the iPhone again but this time do not restore the backup and set it up as new to see if the issue persists without the previous configuration.
Just incase you need it, this article will help with that:
iOS: How to back up and restore your content
http://support.apple.com/kb/HT1766
Cheers,
Sterling

After updating to version 5 for iPhone 4, I am unable to hear incoming call from earpiece. Speaker phone ok.

Unable to hear incoming call in earpiece. Speaker phone ok.

ok thanks for someone "Wjolsten" pointing out that i might have put on the 'ringer silence' button on on the side of the phone. ......................... boy do i feel stupid. thanks all the same for the 'tech support' from Apple, Geniuses?? i dont think so.

Am unable to hear music on i tunes ,music from internet or downloade.

Have itunes 11.1.5
Unable to hear music downloaded or from internet.
On quicktime cannot locate quicktime preference.
Awful ,unable to hear music please advise.

Hi,
Perform a clean install Flash Player may help:
http://helpx.adobe.com/flash-player/kb/clean-install-flash-player.html
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Unable to hear sound when playing Music Sampler from website

Hi
I am unable to hear any sound when trying to listen to music samples on Amazon (for example) and also other websites. I have enabled Firewall to all the internet player, which does launch and start playing but there is no sound.
The volume is definately up on the speakers and I have tested Windows Media Player and it plays radio and other music on my pc perfectly well. So I am unsure as to why I cannot hear the music samples from websites now (I have done in the past).
An example of a link which has music sample is http://www.amazon.ca/Madeleine-Peyroux-Careless-Love/dp/B0002NRRAG
Please can you let me know your comments about this problem.
Thank you

Hi
Did you check if the Wave volume control in the Sound and audio devices was set to higher level???
This control is responsible for the sound volume of any music files.

I'm a recently transformed "Windows to Apple" user, and I need to run various Windows software. Before installing Windows, I would like to hear from experiences from users if it works well.

I'm a recently transformed "Windows to Apple" user, and I need to run various Windows software. Before installing Windows, I would like to hear from experiences from users if it works well. Also, I have an "Office for PC" that I need to re-download, however I was advised by someone that this software cannot be downloaded even if I had Windows in my MAC and that I will have to buy a new "Office for MAC" software. Thanks.

Yes, what you are looking at will work.
"Most of this would be for access to the shared folders which is not the same as RDP, correct? So i could
have myself connect from school to pull a word document, my friend connect from home to get the excel spreadsheet for our table top gaming, and my family connect to pull pictures from the shared folder on the server all at the same time. Because they
are accessing the shared folders it is not a RDP where they are accessing the server itself for administration."
This statement is correct. All of them would be able to be accessing the shared folders at the same time. This is the purpose of shared folders.
"the 1 user and RDP part is where I'm getting a little confused i think.
For the RDP part I thought that only applied to the server itself and not any of the client computers
connected to the server. So you are still limited to the 2 users to connect concurrently to the server or a client computer at any time?"
Sorry, not trying to confuse you. You mentioned to connect to a local machine at the same time. If you are staying away from RDP, then you won't have this issue. I would keep all shared folders on the server, not on any workstations.
You are correct 2 people can be RDP into a server at once. For client computers (workstations) you are limited to 1 person at a time. If you setup Anywhere Access correctly, then your friends and family should not need to RDP into a
client computer, they should only need to access the shared folders.
Something to keep in mind...for Anywhere Access to work, you will need to purchase a public certificate. You can do this from GoDaddy.com, Comodo or others. I would recommend either Godaddy or comodo. They make it easy and give plenty of instructions
on how to obtain the certificate. You will probably also have to purchase a domain name, and a static IP from your ISP. To fully do what you are looking at, it will take some out of pocket $$.

Users unable to submit form

I am having a problem with some of my users unable to submit forms. They can see the submit button but when they click on it nothing happens. I do not receive the data into my database and they do not recieve my automatic confirmation that they should get upon submission. Others have no problem. I've tested the link and seems to work fine for me in both IE and Firefox.

I am helping Shannon out with this one. I'm sorry to hear you are having problems.
I have tested your form, but everything looks fine from this end.
Can you provide some information about the users who are experiencing the problem? What operating system are they using? Windows 7? Windows XP? Mac? What browser and version are they using?
At the top of the form, does the user see the message 'Javascript is not enabled in your browser.'?
Try closing all instances of the browser, open the browser, clear the browser cache, and reload the form.
Try another browser.
Can you provide a screenshot of the form when the user experiences the problem?
Thanks,
-DevRandy

Unable to call from my skype out account

Hi!
Iam unable to call from my skype out account to india, but i can able to call skype to skype users.pls advice.otherwise pls advice how to cancel the membership and get my money back.
Regards
Rajan

Contact your carrier.

How do you fix 'unable to upgrade from version 0'?

I have been working on 6 ibooks over the past year, documenting a lot of stuff for user manuals for our school. The ibooks were all created in iBA version 1.0, but are not published - we only use them internally so we just use the previews.
I gave up trying to upgrade my 1.0 iBooks, it takes too long to 'optimize' the files when I try to open them in 2.0. I have read all the issues with iBA 2.0, but decided to download 2.0 on another computer and wabt to try to re-write all my old 1.0 manuals (I have all the files that went into them).
However, when I double-click to open the 2.0, nothing happens. So I go to 'File' and select 'New from Template Chooser'. I then get the window with all the new templates, including the portrait ones. When I select any template, say the 5th one for example, I get the prompt "The document 'Textbook 05.ibatemplate' could not be upgraded. Unable to upgrade from version 0". This happens for every template. I don't understand. I downloaded the 2.0 from the app store onto a 'clean' computer. Yes, it has Lion on it and all the spec requirements to run iBA. Can anyone help me with what to do next?

Did you ask Apple for help yet?
[email protected]
…support phone number call +1 (877) 206-2092.
Global Phone Support
We have expanded English-language publisher phone support. To make contacting the iBookstore support even easier, new local phone numbers are now available for Australia, France, Germany, Italy, Netherlands, Spain, and the U.K. Support is available Monday to Friday, from 7 a.m. to 5 p.m. (PT).
Country
Phone Number
Australia
1300 307 504
Note that this is a low tariff number.
France
0805 540 117
Germany
0800 664 5307
Italy
800 915 902
Netherlands
0800 0201 578
Spain
900 812 687
U.K.
0800 975 0615
U.S.
+1 (877) 206-2092
Toll-free from U.S. and Canada.

Disappointed with IOS7, i had organized my music library as per the Genre and now im unable to hear all the songs of the same genre like in the earlier versions. The options of "all albums" and "all songs" are missing in this version of IOS. Help Please..

Disappointed with IOS7, i had organized my music library as per the Genre and now im unable to hear all the songs of the same genre like in the earlier versions. The options of "all albums" and "all songs" are missing in this version of IOS. Help Please..

It would be nice if you told others the steps you've tried and/or how you used to have your setup.
Anyway have you tried tapping MORE this will then bring you to
the selection-list of Audiobooks, Genres, Compilations & Composers.
Selecting Genres gives you a list of all your music split into genres which was set within the Music downloaded via iTunes or uploaded from CD or which you may have set yourself.
Then you just select the Genre you want:
If certent songs are not correctly gategorised you may need to go into iTunes and reselect via Get-info
>Info>Genre and change it there. That way you should end up with all songs of Jazz or other in 1 place.

User unable to hear from diferent WLC registered AP

Similar Messages

Maybe you are looking for