Very bad D/Load speed

Moved to a small village and my D/S is only 320Kb/s ! BT Vision does'nt work either. They do'nt tell you about that when you buy BT products!

if you check the attenuation with this site it will give you some idea of connection speed on a good line with no noise problems
http://www.kitz.co.uk/adsl/max_speed_calc.php
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Similar Messages

  • TS1398 Ipad Minin -Cellular 64GB Slow down load speed ???

    Hello From Australia
    Question I recently boiught a new  Ipad Minin -Cellular 64GB and am very disapointed
    Reason is Very Very Slow down load speed ??? My Ipad Minin -Cellular 64GB when connected to our home Telstra  high-speed Wi-Fi  Internet has a maximum download speed of say 2Mbps while my laptop pro (side by side comparison) is downloading at  8Mbps ?? I am using a Telstra Technicolour :
    Wireless Access Point - Telstra
    Configuration
    Interface Enabled:
    Physical Address:
    a4:b1:e9:79:99:b5
    Network Name (SSID):
    Actual Speed [Mbps]:
    65
    Band:
    2.4GHz
    Region:
    Australia
    Channel Selection:
                                         Automatic                                     Manual                                  
    Channel:
                                         1                                     2                                     3                                     4                                     5                                     6                                     7                                     8                                     9                                     10                                     11                                     12                                     13                                  
    Channel Width:
                                         20MHz                                     20/40MHz                                  
    Allow multicast from Broadband Network:
    Security
    WPS Enabled:
    Broadcast Network Name:
    Allow New Devices:
                                         New stations are not allowed                                     New stations are allowed (via registration)                                     New stations are allowed (automatically)                                  
    Encryption:
    Disabled
    Use WEP Encryption
    Use WPA-PSK Encryption
    WPA-PSK Encryption Key:
    WPA-PSK Version:
                                         WPA                                     WPA2                                     WPA+WPA2                                  

    This is the iPod touch forum. I requested your post be moved to the iPad forum.

  • I am a macbook pro user form last 2 yrs, recently i upgraded to Mountain Lion from Snow leopard. Since then  operational  speed is a major concern. Now It has crashed so very badly that I am scared of my data.Please help me.

    I am a macbook pro user form last 2 yrs, recently i upgraded to Mountain Lion from Snow leopard. Since then  operational  speed is a major concern. Now It has crashed so very badly that I am scared of my data.Please help me.

    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • Ever since I  loaded mountain lion, my macbook runs very badly.  It it very slow to react to any commands or cursor movements.  It freezes for about 15 seconds at a time.  It does not have that fact response like when I first bought it.  Any suggestions?

    Ever since I loaded Mountain Lion onto my Macbook, it runs very badly.  It freezes for 15 seconds, does not respond to cursor instructions and just reacts very slowly.  Any suggestions?

    You have a better chance of a response over on the Mtn. Lion community.
    https://discussions.apple.com/community/mac_os/os_x_mountain_lion

  • T400: Very bad experience

    I really don't know where to start, I have had so many problems with the T400 from the past one month! So, let me start at the beginning: 
    PC Config: WinXP, P8600, 4 GB Ram, 160 GB/7200 RPM, ATI 3470 card.
    1. I got the the PC the 2nd of October. Out of the box, the computer was slow, much slower then my one year old Dell Vostro (1.6 core2duo, 160 GB/5400 RPM, 2 GB RAM, Win XP). The Vostro trumped the T400 both in boot time and regular usage. 
    2. I then started having issues with the display. Started getting weird lines on the screen. The speakers were making a screeching sound and there were some issues with the microphone as well. Called up Lenovo tech support and sent the PC to the service center. To top it off, I had a very bad keyboard with abnormal amounts of Flex and a displaced thinklight which was illuminating me rather than the keyboard. 
    3. The folks at the service center replaced the system board and also said they fixed the speakers. 
    4. I got the computer back and I continued having issues with sound. Sometimes, it doesn't play. And when it does, it has that screeching sound again. The PC was incredibly slow too. No improvements in the booting speed or speed during regular use. The didn't fix the computer back properly and everything from the plastic around the display to the case around the over the media card was loose. I could make out they hadn't put it back properly and I would press it in and it would come out. Moreover, the computer started hibernating all of a sudden. It is so irritating when you are in the middle of a presentation and all of the sudden the computer goes off. I had to restart it constantly. It also hibernates suddenly when I start up the computer from hibernation mode. I enter the windows password and once I'm in windows, the PC hibernates. 
    5. I called up technical support and told them all these issues. They said I can send it back in again for repair. I told 'em I would rather want the PC replaced rather than send it to repair again since I may have start having issues with it again. After 8 factory restorations, moving 100 GB data around each time and installing all applications again, I was fed up. 
    6. They agreed to replace the PC and I got the new computer today i.e.., 4th Nov '08. This is where things get interesting. The computer started up normally and I got the initial settings configured. Once I got into windows, the first thing I did was restart the computer. As it was booting, it froze at the XP loading page. I restarted the computer via the power button, and the same thing happened. I continued restarting for another 3 times with the same result. So, assuming a bad OS installation, I went ahead and did a clean install through thinkvantage. As the installation was going through, at some point of time, the PC restarted and got stuck at the same XP screen again. I restarted it a couple of times until, fortunately it went through. It then started installing applications and for some reason, it restarted and again got stuck at the XP loading screen. As of now, it is stuck there and won't go through.
    7. I got on the phone with tech support and the only thing they could do was to send it to the service center. 
    A brand new computer right out of the box is heading to the service center. It doesn't feel like a new computer any more the moment it goes to the service center. I'm utterly and totally disappointed with the way Lenovo is building these computers. If this is the case, I might as well take my business elsewhere. 
    I don't know if I'm the only person out here with such problems or if there are any one else. And, I apologise for such a long post.. Please tell what I can do now. I don't want to go through the same headache again. 

    If it was 'really dark/ clear' then why sales guy was offering me a contract with a phone? Also, he said everything is clear from their side when I said I am interested in the best buy offer. This is very bad when you are ready to sell on your contract, but don't allow customers to buy from others.
    Just wanted to let you know this 'customer service' as I spent more than half day in long waiting at both best buy and verizon shops... I thought I would get some solutions... Anyway, I moved on...

  • Fios Internet connection is very bad! Please help!

    Hello,
    I play an online game called Final Fantasy XIV.  I use a program called WTFast in order to have a solid gaming experience, one without or very little lag or disconnects.
    Recently, within the last 3-4months, I have noticed I get EXTREME lag and DISCONNECTS.  I contacted WTFast with a tracert that they analyzed, and here is their response:
    "Your internet connection is very bad. There is a "plateau" spike. This will cause WTFast to spike as well, and for such a long "spike" it is not surprising that the connection was dropped.
    The previous report showed a very unstable internet connection as well (the one where you got a 30 second freeze).
    Present the same reports you sent to us to your ISP (Verizon FIOS) and ask them to try to make their connection better. The report will help them see the quality of the current connection."
    Here is the information in the more readable form (except for the last four as I figured you would probably get the idea by then). Yes, 4 shows 100% packet loss, so the connection dropped then. Also, in 5 the standard deviation is high (16.35 ms) which indicates a huge fluctuation in the signal. The flux column also shows large numbers, which indicates a large variance in the signal speed. Finally, there are a lot of hops just within the ISP, ie rows 2-8, and all this data is for the ISP itself, not the WTFast connection. In fact, that connection is the last one, and there you can see good numbers. Hope this helps.
    015-02-25 00:09:36
    Hop Name No. Loss % Sent Received Best (ms) Avg. (ms) Worst (ms) Last (ms) Spikes Flux (ms) Std.Dev (ms)
    Wireless_Broadband_Router.home 1 0.00 497 497 0 0 12 0 0 0 1.67
    lo0-100.PHLAPA-VFTTP-304.verizon-gni.net 2 0.00 497 497 3 8 84 7 4 72 8.39
    T1-1-0-5.PHLAPA-LCR-21.verizon-gni.net 3 0.00 497 497 4 8 19 9 0 0 2.51
    —— 4 100.00 —— —— —— —— -1 —— —— —— 0.00
    0.so-6-0-1.XL3.IAD8.ALTER.NET 5 0.00 497 497 10 19 137 12 12 92 16.35
    TenGigE0-6-0-4.GW1.IAD8.ALTER.NET 6 0.00 497 497 11 18 50 18 0 0 4.68
    teliasonera-gw.customer.alter.net 7 0.20 497 496 12 24 43 27 53 30 3.80
    cloudflare-ic-309918-ash-b2.c.telia.net 8 0.00 497 497 10 14 46 13 0 0 3.04
    Target WTFast.com 9 0.00 497 497 9 12 25 12 0 0 1.94
    February 25, 2015, 11:56
    I did a tracert from my computer to sites like MSN.com; Verizon.com etc, and EVERY SINGLE 4 shows a 100% loss.  I did the same tracert from my computer at work that uses a different IP provider, and those same sites show a response from 4.  
    Can anyone help me out with this please!  Thank you for reading!

    bap4201 wrote:
    I'm trying to, but can't seem to format it properly
    Open a command prompt and enter the tracert command
    then select the cmd prompt icon - top left of the cmd prompt window
    select edit, mark
    highlight the data you want to copy - the tracert data
    select the cmd prompt icon again
    select edit copy
    put the cursor in the post window in the forum
    and hit ctrl-v - as below
    C:\Users\Peter>tracert wtfast.com
    Tracing route to wtfast.com [190.93.243.228]
    over a maximum of 30 hops:
    1 <1 ms <1 ms <1 ms Westell [192.168.1.1]
    2 3 ms 2 ms 3 ms L101.BSTNMA-VFTTP-66.verizon-gni.net [96.233.107
    .1]
    3 7 ms 6 ms 6 ms G102-0-0-3.BSTNMA-LCR-22.verizon-gni.net [100.41
    .212.48]
    4 3 ms 3 ms 3 ms so-5-0-0-0.BOS-BB-RTR2.verizon-gni.net [130.81.1
    51.220]
    5 11 ms 12 ms 10 ms 0.ae11.XL4.NYC1.ALTER.NET [152.63.20.117]
    6 * * * Request timed out.
    7 37 ms 28 ms 43 ms 3.et-2-0-1.TL2.NYC1.ALTER.NET [140.222.227.34]
    8 20 ms 21 ms 23 ms TenGigE0-7-0-1.GW5.NYC4.ALTER.NET [152.63.17.66]
    9 12 ms 10 ms 11 ms teliasonera-gw.customer.alter.net [152.179.163.1
    78]
    10 13 ms 13 ms 11 ms nyk-bb2-link.telia.net [213.155.130.244]
    11 11 ms 11 ms 12 ms nyk-b2-link.telia.net [213.155.130.30]
    12 12 ms 17 ms 19 ms cloudflare-ic-309915-nyk-b2.c.telia.net [62.115.
    52.174]
    13 11 ms 12 ms 11 ms 190.93.243.228
    Trace complete.

  • HT1577 how do a get a refund on a ridiculously slow downloading rented movie for my apple tv dispite a 5mb/sec down load speed? my first experience with appletv movie rental. no good. rented at 4:30pm. still waiting for standard def movie to finish at 8:1

    how do a get a refund on a ridiculously slow downloading rented movie for my apple tv dispite a >5mb/sec down load speed? my first experience with appletv movie rental. no good. rented at 4:30pm. still waiting for standard def movie to finish at 8:10pm. Not good enough.

    Thanks for the pointers folks. Yeah, 1.5GB is pretty poor isn't it? There are other suppliers, but you have to get a their phone line installed to access the internet so it's an £85 setup fee plus a day off work for a guy to come round and drill a hole in your wall before you even get to the monthly costs.
    Don't get me wrong though - I'm certainly not an Apple basher, but am equally frustrated with both them and the ISP.
    Virgin Media spend all kinds of money advertising their broadband as the fastest in the UK, but don't tell you (up front anyway) that you'll be cut off if you actually try and use it.
    Apple on the other hand carry on with their 'it just works' mantra, but with Apple TV this only applies if you meet certain criteria (again, not mentioned up front).
    I guess it aint a biggie, as i was gifted my Apple TV, and love all the other stuff it does, but from the number of posts on this forum can see that there's a lot of angry customers out there who want explanations as to why they're having similar problems to me.
    Will be very interesting to see if Apple release any kind of software update that turns the flash drive from a buffer to permanent storage, to at least ease some of the pain...
    Message was edited by: McGinty

  • Slow loading speed

    I use verizon DSL, my plan is $29.99, and the speed is up to 3 Mbps/
    768Kbps. I checked the speed at http://infospeed.verizon.net/speedtest/, it always is under or around 2414Kbits/Sec and 301KBytes/Sec, Occasionally reach 2822.9Kbits and 352.9KBytes. and the page's loading speed is very slow,
    what's wrong about it?
    Thank you and happy thanksgiving to all.

    2414Kbits/Sec = 2.4 Mbps. I would say your connection is doing very well. You will never reach 3 Mbps as this is the theoretical best that you can do. Speed can vary greatly. That said, testing on the Verizon site I got 84507Kbits/sec (84.5 Mbps!!! ??) on my 6 Mbps cable connection. On other tests sites (see below) I got between 1.2 and 5.7 Mbps today. Speed can really vary sometimes for various reasons including network traffic. Try some of these tests and contact Verizon if you are not satisfied for more information about your connection and speed. Note that the speakeasy test also tests your upload speed, which is very unusual for these types of tests.
    http://www.speakeasy.net/speedtest/
    http://www.testmy.net/d_load.php

  • PS CC 2014 very slow to load and operate after 2014.2 update

    I updated my Photoshop CC 2014 64bit today.  It was working perfectly up to the update.  Since the update, PSCC 2014 has been very, very slow to load and slow in use.  I have uninstalled PS used the PS Cleaner and reinstalled through CC Desktop.  The speed problem remains.  Interestingly, 3D is the Menu feature that seems to take the longest to load.  In other words, the program eventually loads, but 3D appears 6 or 7 seconds later.  I don't know if this is significant.  The setup was working fine up to the update.
    Grateful for any ideas about what may be the problem and what I can do about it.
    My system is a 3770K, with 32Gb ram, x4 SSDs one dedicated to OS and programs and the others to data, and an Asus GTX660 (2Gb) graphics card.  I am using the latest driver from the Nvidia site.  OS is Windows 7 64bit.
    I am getting no error messages - just great sluggishness.
    Thanks.

    Sorry for the delay in responding.  I had to get some sleep.
    Changing "sniffer" made no difference I'm afraid.  I have put it back to "sniffer.exe" having tried reopening with "~sniffer" twice with no success.
    Resources.  The maximum cpu resource used during the period from clicking the desktop icon to the menus in the program becoming usable is 23%.
    At the end of the splash screen when "initializing panels" is briefly on the splash screen, the line for the resource meter for the cpu went red and said "not responding" - the red disappeared once the workspace was active:
    Do you need anything more?

  • IPad 1 Gen. With 5.1.1  its Running very Bad

    I have a iPad 1 Gen. With the 5.1.1 iOS and its Running very Bad , restarts and Black Screen is comming so much That i Cant use the iPad normal :( what can i do.? I try to downgrade but Iam Not abble to fix ist to 4.0 or 5.0 :(

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    The problem could be with your router and internet connection. You can download several apps to check your speed.
    How to Fix a Slow iPad
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-A-Slow-iPad.htm
    iPad running slow? How to speed up a slow iPad
    http://appletoolbox.com/2012/07/ipad-running-slow-how-to-speed-up-a-slow-ipad/
     Cheers, Tom

  • AppleWorks 6.2.9 on OSX 10.4.6 imbedded images print VERY badly

    Ever since my upgrade from an older version (don't remember which) of AppleWorks on OSX 10.2.x - in that arrangement all was well, now with AW 6.2.9 and OSX 10.4.6 every image I import by any means into an AW document of any type zooms on the screen just fine, very detailed, but prints VERY badly.
    "Very badly" can be defined as, any text which is part of the image is blocky and becomes almost unreadable; all elements of the image blur at every edge - basically, look at a picture through an unfocused lens and you'll get the idea.
    Any other application prints crystal clear using the same image files that AW messes up. I used to use AW to make my business letterhead, business cards, logos, media labels, etc. Now I'm doing all that by coding directly in PostScript because AW won't print nice copy.
    I've been trying to find any settings in AW prefs regarding aliasing, smoothing, dithering, you name it, and nothing I've tried makes any difference.
    Any ideas where to go to tell AW to play nice with the printer like it's ancestors used to?
    Again, EVERY other application prints perfectly, so the printer, driver, cabling, etc cannot be the issue. Only when (and everytime) AW gets involved does printing get munged.
    Thanks for any help anyone can offer me.
    iBook x 2 = G4 + G3   Mac OS X (10.4.6)   lots of pro audio packages....

    Thanks to all who answered.
    I'm thinking it would have been nice of Apple to let us know that they were going to change something as wide-ranging as how images are imported into AW documents. As was mentioned by Yvan, the 72dpi limit was apparently introduced with AW6. Thanks for the clarification, also. I suspected that the OS (10.4.6 for me) and drivers were clean; since every other app I have prints perfectly. The very same files used to import into AW(older) and print fine just as they were on the older system.
    Peggy, yes, most of the images in question were .tiff and .jpg formats, usually from a scan or a conversion from a .ps or .eps into a .jpg or .tiff.
    Not being a graphic or visual guy (audio yes, but not graphics...), I had no idea what most of the plethora of image types offered by the "save as..." dialog were about, and had no time to try them all one by one. PICT format is fairly deep into the list, so it would've taken me a while to explore the possibilities that far.
    But thank you Peggy, using Preview to convert to PICT format lets me import the images I need and prints them acceptably. I still think raw Postscript is a bit cleaner yet, but for most of my needs the conversion to PICT is so far solving the problem. And if anyone wonders, yes I really do code stuff by hand directly in Postscript. And Perl, and C, and Prolog, and.... So good of OSX to include my favorite editor, emacs! (Old Unix admins never die - we just spawn child processes...or fork and exec - take your pick!
    Hope, interesting that your Intel-based machine had such a problem from the start. Even more interesting that a reload fixed it. Curious what may have been/not been installed in the original factory load.... Glad I'm still on PowerPC architecture - time-tested base of reliability there.
    I did look at the tip from Sharon Joiner (linked by Yvan), but compared to Peggy's suggestion, Sharon's tip seems a bit more involved than it needs to be - at least for my needs.
    Again, thank you to everyone.

  • Firefox is very slow to load the program or any link I click on.

    Firefox and any link takes up to 40 seconds to load. Safari is lightning speed compared to Firefox. I have deleted history and changed to save 5 days, emptied cashe. Still very slow to load anything.
    == This happened ==
    Every time Firefox opened
    == i try to load any page or the program its self

    Ridiculously slow... and I am a long time user. But after a hard disc failure upon loading the latest version I sit and wait and wait and wait and wait. Wha....?

  • Video resolution with Sony Alpha 7 is very bad

    Hi!
    The Videoresolution in PSE 13 Organizer is very bad. Looks like the Videos were made with a cheap mobile-phone.
    Video playback works fine with every other Programm on my PC, for example VLC or Media Player, but when i try to view these Videos with PSE 13 they look awful - unsharp and blurry - same in Premiere Elements 13.
    Have already tried to install Codec-Pack for Win 7, but no changes.
    Maybe PSE uses a wrong codec? If so, how can i change this?
    Camera is Sony Alpha 7, OS is Win 7, Graphichs card is CPU-built-in Intel-HD3000(don´t know if this matters?) with newest Drivers.
    File extension is .mts, format is AVCHD (1920*1080) full HD.
    *edit: maybe it´s helpful if i mention that CPU load is about 30-40% in PSE 13 compared to ~6% when using VLC or Media Player when playing these videos.
    I would be grateful for any suggestions.
    edit*
    after some research:
    let me clarify the problem: is there ANY WAY TO CHOOSE THE CODEC  PSE 13 uses for videos??

    Hi,
    It is by design and we have no option to change it.
    However, we can use Pan Control to enlarge and move around the screen.
    Pan Control: The pan control enables the screen to be enlarged and moved around.
    Enable the pan control: Tap the pan icon in the connection bar to display the pan control and zoom the screen.
    Use the pan control: Tap and hold the pan control and then drag in the direction you want to move the screen.
    Move the pan control: Double tap and hold the pan control to move the control on the screen.
    Disable the pan control: Tap the pan icon in the connection bar to return the screen to its original resolution.
    Thanks for your understanding.
    Jeremy Wu
    TechNet Community Support

  • IPhoto v9.3.2 = v9.4.2  I feel it unfair and unjustifiable to charge for an upgrade of a pre-installed iphoto programme. Please refer to the above version.  This will result in payment on your very bad App Store of £10   Extremely unhappy loyal Mac user!

    iPhoto v9.3.2 => v9.4.2
    I feel it unfair and unjustifiable to charge for an upgrade of a pre-installed iphoto programme. Please refer to the above version.
    This will result in payment on your very bad App Store of £10+
    Extremely unhappy loyal Mac user!!!!!!

    iPhoto v9.3.2 => v9.4.2
    Thank you for your response but in App Store it shows a price of £10+ for this down load.
    (This is a free update. Contact with Mac App Store support > http://www.apple.com/support/mac/app-store/contact)
    Perhaps you are correct but this is not made clear in the update window of this App Store.

  • Load speed: FLEX MX:TABNAVIGATOR LOAD SPEED VERSUS SPARK:TABBAR

    TODAY I NOTICED A LARGE DIFFERENCE BETWEEN
    THE OLDER MX:TABNAVIGATOR
    AND NEWER S:TABBAR (SPARK)
    Summary:
    My test application was built in flex builder 4 and I was using my localhost (asp.net devlepment enviroment) for testing.
    Tests I built:
    I built many proofs for concept using flex objects, ui  and data handlers.
    HOW WAS THIS TEST (which I spoke about in the title) CREATED:
    I built two components which will be used as CHILDREN to the main application.  The fist child component used the SPARK TABBAR and the other child component used the MX:TABNAVIGATOR.  The main application declared these children (using action script) initially and a List control actually loaded the children into the main application.
    BOTH CHILD COMPPONENTS had 10 tabs....
    5 of the 10 tabs contained "grand" child components (none of the components(main application/children/grandchildren) worked with external data)
    RESULTS:
    THE LOAD SPEED BETWEEN THE TWO CONTROLS was very noticable between the two controls.
    THE SPARK COMPONENT (S:tabbar) AVERAGED 3-5 SECONDS TO LOAD
    WHERE THE MX:TABNAVIGATOR ONLY TOOK 1-2 SECONDS
    HAS ANYBODY ELSE EXPERIENCED THE SAME RESULTS?
    THANKS,
    DOUG LUBY OF LOUISIANA
    WWW.douglubey.com
    SEARCH:  FLEX MX:TABNAVIGATOR LOAD SPEED VERSUS SPARK:TABBAR

    It definately seems to fit (pretty good).
    My labels in the "TABS" were of different length.
    So I converted them all to be the same length.
    <s:TabBar dataProvider="{viewstackSampleB}" id="sampleBMainTabBar"left="
    11" top="8" right="11" height="34" fontSize="6"/>
    <mx:ViewStack id="viewstackSampleB" cornerRadius="20" top="40" bottom="10" left="10" right="10">
    <s:NavigatorContent label="Profile___________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="0" right="0" bottom="0" backgroundColor="#000080">
    <sample:SampleB_Profile id="studentProfile" left="2" top="2" right="2" bottom="2"/>
    </s:NavigatorContent>
    </s:NavigatorContent>
    <s:NavigatorContent label="SampleB_DragNDrop1________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="0" right="0" bottom="0" backgroundColor="#000080">
    <sample:SampleB_DragNDrop1 id="studentDragNDrop1" left="2" top="2" right="2" bottom="2"/>
    </s:NavigatorContent>  
    </s:NavigatorContent>
    <s:NavigatorContent label="SampleB_DragNDrop2________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    <sample:SampleB_DragNDrop2 id="studentDragNDrop2" left="2" top="2" right="2" bottom="2"/>
    </s:NavigatorContent>  
    </s:NavigatorContent>  
    <s:NavigatorContent label="SampleB_PullDataFromParent" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    <sample:SampleB_PullingDataParent id="studentPullingDataParent" left="2" top="2" right="2" bottom="2"/>
    </s:NavigatorContent>  
    </s:NavigatorContent>  
    <s:NavigatorContent label="Tab Five__________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    </s:NavigatorContent>  
    </s:NavigatorContent>  
    <s:NavigatorContent label="Tab Six___________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    </s:NavigatorContent>  
    </s:NavigatorContent>  
    <s:NavigatorContent label="Tab Seven_________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    </s:NavigatorContent>  
    </s:NavigatorContent>
    <s:NavigatorContent label="Tab Eight_________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    </s:NavigatorContent>  
    </s:NavigatorContent>
    <s:NavigatorContent label="Tab Nine__________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    </s:NavigatorContent>  
    </s:NavigatorContent>
    <s:NavigatorContent label="Tab Ten___________________" width="100%" height="100%">
    <s:NavigatorContent left="0" top="-3" right="0" bottom="0" backgroundColor="#AEAEAE">
    </s:NavigatorContent>  
    </s:NavigatorContent>  
    </mx:ViewStack>
    THIS APPEARS TO HAVE THE SAME LOAD TIME as the TabNavigator.
    So I have to ask:
    What is a permanent fix for this.
    Where I can I update my current "Build" for FLEX 4
    so my application does not retain this bug.
    OR ANOTHER QUESTION...what can I exclude in my declarations to fix this bug.
    I would prefer to use the Spark TabBar over the mx:tabnavigator
    MY CURRENT "BUILD" is 4.0.1.277662

Maybe you are looking for