Video Advantage 2.0 problem

My problem here is that when I start up video advantage I see the same image in the local and remote window. This is also happening whenever I make a phone call as well. This is only happening to a few people. Any ideas?

Hello,
I have the same problem for CCM and CME with telephone 7941/61, when I use IP Communicator, VT works fine.
Is there any configuration for telephony 79XX different from Ip communicator?
CCM 5.1
CME 4.1 (IOS 12.4.15T)
Thanks,
Cassio

Similar Messages

  • Video Advantage / CDP Problem

    Dera All,
    We have a problem with several Cisco IP Phones CP-7941G and the Video Advantage Software. The phones are running the SCCP41.8-3-3SR2S firmware but problem exists also with the SCCP41.8-3-3S firmware.
    As far as I can see the phone does not send out CDP packets on the PC switch port. Within CSCsk11000 an error in the CDP implementation is described for the firmware version SCCP41.8-3-2SR1S.
    Attached you find Wireshark Sniffer File describing the issue. A capture filter limiting the traffic source to the phone was applied.
    Here are some comments what happened outside the wire:
    Packet Comment
    3 The phone was restarted to enable the settings access. It was then assured that not only in the Phone configuration on the CallManager (Version 6.01) CDP on the PC port was enabled but also on the phone itself. As you can see there are no CDP packets. Within the Video Advantage Software there is no connection between the phone and the camera.
    4 The phone was reset. CDP packets are sent out immediately.
    22 or 23 Within the Video Advantage Software the phone is connected to the camera.
    In all our investigated cases a reset of the phone while the Video Advantage Software is running was successful.

    I tried the three most recent versions
    SCCP41.8-3-2S
    SCCP41.8-3-3S
    SCCP41.8-3-3SR2S
    With all three versions VTA works if the phone was reset while the Video Advantage Software was running. After a while (between a day and a week) the phone stops sending the CDP packets and VTA is no more working at the next start. The SCCP41.8-3-2S version seems to be the most stable regarding this issue.
    The mentioned bug does not fit as we run CCM6.
    Thanks for your help.
    Thomas

  • Best camera for Cisco Video Advantage

    Hi,
    I am looking for a camera which is having the best specifications for Video advantage. It looks like the Microsoft LifeCam NX-6000 is the one. (1600 x 1190 with 30 fps) Does anyone have experience with this camera or who has good experience with a camera which is not listed in the "tested" camera list:
    Cisco VT Camera II
    • Cisco VT Camera
    • Logitech QuickCam Fusion
    • Logitech QuickCam for Notebooks Pro
    • Logitech QuickCam Pro 5000
    • Logitech QuickCam Ultra Vision
    • Microsoft LifeCam VX-6000
    • Microsoft LifeCam NX-6000 Webcam
    • Creative Webcam Live Pro USB 2.0 Webcam
    Thanks in advance,
    Jeroen

    Hi Mark,
    Thanks a lot for your reply. We tried several models which are not in the list. They all worked. The only problem is that the Video Advantage narrows down the format. I tried the Logitech Quickcam Sphere AF. In the Logitech application it's a great Webcam in with HD quality but these are the Specifications of Video advantage:
    • H.263 and H.264 video codecs: Bit rates from 50 kbps to 1.5 Mbps
    • Video formats (up to 30 frames per second): 352 x 288, 320 x 240, 176 x 144, and 160 x 120
    • Interoperable with most third-party H.323 video terminals from verified IP video telephony partners
    So it's only working at 352 x 288. I hope the next version of Video advantage is able to increase the resolution.
    I would also like to know if there is a way to enable the camera automatically when a phone call is established.
    I don't have a MCU to do video conferencing but is there a way to conference a none-video phone into an video conversation?
    Thanks!
    Regards,
    Jeroen

  • Cisco Unified Video Advantage - CDP Driver Not Installed- Windows 7 64-bit

    OK, so I'm sure the problem is Windows 7 64-bit, but after installing version 2.1.2 of Video Advantage, although everything goes in with no problem... it's not connecting to either my CUPC soft-phone or the attached video enabled Cisco IP Phone .  When I click on About, there is no version listed next to the CDP Driver Version.   When I go into Device Manager, I don't even see the Cisco CDP Driver listed.  There were no error messages during the install, but it would appear that the CDP Driver didn't get installed during setup.  This, of course, would explain why the phones are not being detected (since it uses CDP for discovery).
    Has anyone come across this and come up with a workaround ??

    If you download the PDF for Cisco Unified Communications Support for Microsoft Windows 7 that was published on 10-22-2009 you will see that currently there are no plans to support Video Advantage on Windows 7. I haven’t tried installing it on my 64 bit Windows 7 system yet but have you tried installing it using the program compatibility wizard? If that doesn’t work you can install the XP Mode which is a virtual machine of Windows XP that would allow you to install it there. The XP Mode virtual machine has worked for me on every app so far that doesn’t work with Windows 7.

  • Cannot mke offnet calls with Video Advantage running

    I have Video Advantage version 2.1.2. When I make an offnet call via an h323 gateway, I hear a fast busy and the called person hear the phone ring. When they answer the phone, they get dead air. When I close or disable Video Advantage, I have not problems with calls.

    When running Video Telephony Advantage (VTA), outbound calls fail from Cisco CallManager through H.323 gateways to PSTN. An invalid bearer capability IE field is indicated in the release_comp message
    http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K18460760
    HTH
    java
    if this helps, please rate

  • Using Video advantage with IP Communicator on CME 4.0

    I am having issues getting video advantage to work with IP communicator. I am using VA 2.0.2.0 and IPC 2.0.2.0 and CME 4.0. I added the commands
    voice service voip
    h323
    call start slow
    telephony-service
    service phone videoCapability 1
    call-park system redirect
    create cnf-files
    and added the video command under the ephone. If you have any suggestions I would appreciate it.
    Thanks,
    Andrew

    Paal
    I am not using Call Manager. I am using Call Manager Express. There is no version 4.1 the documentation says that it should work with 4.0. that is the latest version of CME. Do you have any insight on this.
    Thanks,
    Andrew

  • HT201401 I have no volume on recorded videos; what could the problem be?

    I have no volume on recorded videos; what could the problem be?

    you have no control, or you have no sound?

  • Camera for use with Cisco Unified Video advantage?

    Cisco is EOLing the Cisco Unified video advantage product that we thought would be a good fit for us to integrate video with some of our IP Phones.  I can still order the Video Advantage software until later in the year from Cisco but they have discontinued the Cisco VT Camera III that was previously used with this product. 
    They list the Logitech C920-C web cam as a replacement for this product, but it seems to be difficult to locate.  The realease notes say you can use a 3rd party camera but Cisco does not officially support it. 
    Has anyone used any third party cameras with Cisco Unified Video advantage and if so which would you recomend.  I was hoping to use the Logitech HD Pro Webcam C920 (the generic non Cisco version) but wasn't sure if it would work ok? 
    What do you think?  This will be using Unified Video Advantage 2.3. 
    Jim                   

    Hi,
    We have been using Video advantage v 2.1.2 with 7940 series phone since long, it works fine with almost all 3rd party camera`s and even with the inbuilt laptop cameras.
    v 2.3 is an enhanced version as compared the one which we are using. So i would suggest you to go ahead and try it with any good qaulity webcameras available in market.
    Further to add there are certain PC requirements which needs to be met, the same can be found in the below link.
    http://www.cisco.com/en/US/docs/video/cuva/2_3/release/notes/relnote_cuva23.html#wp1118706

  • Hi, since i put some mp4 video or DVD files on my external hard drives final cut prox won't recognize my hard drives, i move all the video files and the problem still exist. somebody have the solution

    Hi, since i put some mp4 video or DVD files on my external hard drives final cut prox won't recognize my hard drives, i move all the video files and the problem still exist. somebody have the solution

    Did the back and forth between PC and Mac file systems screw up my files somehow?
    Yes. Unfortunately the move has almost certainly caused the loss of the resource data that would have been (invisibly) attached to those files.
    By adding a specific .mov extension after the fact you will have helped the Mac correctly identify the file type / asscoiations but also significantly you will have physically changed the filename eg from "clip" to "clip.mov". This means that when you come to reconnect the media in FCP , then FCP will be looking for files that no longer exist at the given path eg when specifically looking for our example clip called "clip" of course it won't find it.
    Try this as a test... first remove the ".mov" extension from one or more of the clips, select those clips and press Cmd-Opt-I to open an Info window for the selection. You'll see an "Open with:" popup and in that popup you should choose QuickTime Player (if its a Unix Executable then it will initially list Terminal as the appropriate app, you have to choose Other... then in the open dialog choose Enable > All Applications and then navigate to and select the Quicktime Player app as the appropriate app). After you've done that restart FCP and see if you can now reconnect to those clips.

  • Can't make Offnet Calls with Video Advantage on

    I am no expert so I could be missing something basic. However, I have a Cisco phone that is logged in and is enabled for video. I installed the Video Advantage and all works well. I can make onNet calls with Video advantage on. However, I cannot make offnet calls. If I exit video advantage I can once again make offNet calls.
    Any Ideas?
    Ryan

    Have you tried this:
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080569b65.shtml
    Best regards.

  • Switching webcam player video format black square problem

    switching webcam player video format black square problem:
    After the webcam player is stopped and the format changed and player is started using a new format there is a black square that appears over the screen area that partially covers up the webcam session.
    Why is this happening?

    Just incase anyone else runs into this problem, I was able to solve it by calling setVisible(false) on the current visual component.

  • Cisco Unified Video Advantages is not connected to any phone

    There are CME 4.1.0.1, cisco video advantage 2.0, Cisco IP Phone 7940,Cisco VT Camera.
    Video advantage can`t see phone.
    But with CIPC it works correct.
    In logs I saw an error:
    CDP Driver Open failed with error-code 00000002
    What is a way to connect phone to VT advantage.
    What is the way to connect Video advantage with IP phone?
    thanks in advance.

    plug ur desktop/laptop to the back of the IP PHONE's data port~ to associate with the Video Ad

  • Trying to open youtube, QuickTime cannot open video.3gp, only a problem since upgrading to Mavericks

    trying to open youtube, QuickTime cannot open video.3gp, only a problem since upgrading to Mavericks, what do I need to do please ?

    You're right. It wasn't QuickTime itself. I solved all the problems myself.
    The main reason why QuickTime files weren't working was because the newest audio driver from Creative released July 2007 (using their autoupdate) is apparently for Windows Vista (it has the name Vista in the update title). Why that update showed up on my Windows XP Pro system, I have no idea. So, I went to Creative's site and got the driver before the latest release, and all works well.
    The Microsoft update (from June 2007, I noticed today, not July) is another issue. It's based around the file P17RunE.dll, which is something from Microsoft for the SoundBlaster. Not sure what it does, but I don't need it.
    Sorry for wasting all your time on a non QuickTime issue, but thanks for the help.

  • 3511 MCU with video Advantage

    1.DOe the 3511 MCU supports cisco Unified video advantage ( PC- USB camer based video product) for 3 or more party video conferencing ?
    2. Does the video advantge endpoint can do video conference with IP phone 7985G ?

    Answer is 'Yes' for both questions.
    You can configure 3511 to use either Skinny or H323 protocol. If configure as Skinny, then it is just another CFB in CM; CM will allocate it as per MRG and MRGL configuration. If configured as H323, then you have to configure 3511 as H323 gateway in callmanager and have a RP to point to the gateway. Typically, the RP will be your conference ID number.
    7985 is just another video phone like VTA with an IP Phone; and they do support same type of codecs. Hence you can use 7985 to do video call with VTA as well to do conference with an MCU.

  • Video Advantage OS supported

    Hi,
    I was wondering if Cisco Unified Video Advantage was supported in operating systems other than Windows?
    Any help is much appreciated.

    No. CUVA uses a Windows-only CDP driver to make that magic happen. Either way CUVA is EoS and it's functionality is being carried forward in the CUPC/Jabber products.

Maybe you are looking for

  • ArrayList problem

    Well, im new to ArrayList and im having great trouble trying to figure things out, this is what im supposed to do: The Problem A banking institution offers certificates of deposit (CD's) with a variety of interest rates, and maturities of 1, 3, 5, an

  • How do I add 2003 Exchange account to Mail using Snow Leopard

    I have my Exchange 2003 account working on my iPhone perfectly. I recently upgraded to Snow Leopard and would like to add the account to Mail. When I go through the set-up it asks me different info than the iPhone did. I've tried several possibilitie

  • Convenience Key on my Torch does not work

    Hi Everyone! Seek your help as the convenience key on my torch does not work. I have changed the setting as well but to no avail. Regards - Nitin Solved! Go to Solution.

  • Mac and Windows on one license

    I purchased photoshop CS5 for my mac and would like to install it on my windows laptop too. I downloaded the tial version and attempted to use my current key and it wouldn't accept it can anyone help please? Thanks

  • Reflect problem

    I am new to Java and I am sorry if this has been raised previously. i want to get and set all of object's fields not only public fields but also private, protected and package fields. And i have been advised that i should use one of sun.misc.unsafe o