VLAN Membership Error

Hi,
I'm trying to exclude a port from the default vlan but I receive this error;
A VLAN port can only be untagged to one VLAN ID. (LAN2)
I only have 1 vlan, so I don't see why I should be seeing this?
I'm trying to exclude the port so I can add the port to a new vlan which I haven't created yet. I've tried creating the vlan before hand but I get the same error.

Hello Bobby,
You need to create all your VLANs first. Then, once they show up in the VLAN table, check the boxes next to each VLAN and click 'edit'. Now change the port to 'untagged' or 'excluded' for the desired VLAN. Remember, only one VLAN can be untagged on each port and there must be an untagged/native VLAN on each port.
Regards,
Mike.V

Similar Messages

Cant find the vlan-membership command

I cant find the vlan-membership command on my 3700 layer 3 switch, i've searched google on whether the command has upgraded to a new syntax to no avail, i'm using GNS3 and the IOS is c3725-adventerprisek9-mz.124-25d.bin

Now I got your problem. Layer 3 switch has routed ports require ip address and can't be added in vlan.
if you want to add ports into vlan then it should be swtiched port not a routed port. to make routed port as switch port use "switchport" command under interface and use switchport acess vlan to add a port in vlan.
Further more it can communicate with VLAN1 and VLAN2 through the SVI interfaces of the VLANs (int vlan1 and int vlan2).
I hope the above info will solve your problem.

VLAN Input Errors

I have numerous 2950 switches on my network with multiple VLANS on them. Some of them are getting tons of input errors on the main VLAN. How can I stop this? What is causing it?

The issue may be due lot of multicast packets through the network. This may cause issues as VLAN input errors.

Set-VMNetworkAdapterVlan throws Failed while applying switch port settings 'Ethernet Switch Port VLAN Settings' error

Hi,
I'm following this
guide I'm getting an error when running the below command:
Set-VMNetworkAdapterVlan -vmname PurpleVM1 -Isolated -PrimaryVlanId 2 –SecondaryVlanId 4
Generates the following error:
Set-VMNetworkAdapterVlan : The operation failed.
Failed while applying switch port settings 'Ethernet Switch Port VLAN Settings' on switch 'New Virtual Switch': One or
more arguments are invalid (0x80070057).
A parameter that is not valid was passed to the operation.
Does anyone know why this is happening?
ta

Hi TomG101,
It seems that there is a configuration conflict on the virtual switch port .
Also I tested the command on my lab , it works .
For troubleshooting please create a new virtual switch then try to configure again .
Any further information please feel free to let us know .
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Vlan mismatch error

All,
I have investigated and made sure the speed/duplex have been changed between both devices attached to int-faces.
here is my error.
02-ext-liv FastEthernet0/20 (40).
Feb 20 16:22:18.711 PST: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet0/xx
2900 series switch.
What other approach shall I take to pin point the issue since this is only informational on the error log.
-fz
Thanks in advance!

Hi,
The 'error' message is simply because you have used different VLAN IDs on the access ports at either end. CDP discovers this and logs a warning. The message is pretty harmless in itself.
There are a couple of options to get rid of it:
- configure the access port to be the same VLAN on the two switches at either end of the link
--- OR ----
- enable CDP version 1 on your switches. YOu can do this using: 'no cdp advertise-v2'.
The latter option is simpler and you don't really lose much...
Hope that helps - pls rate the post if it does.
Paresh

Apple ios Developer Program membership error

hi i recently brought a Apple ios Developer Program membership but when a day later i got a email that said:
"The billing information you used on the Apple Online Store to purchase an Apple Developer Program membership does not match the billing information you provided during enrollment. Before your membership can be activated, we'll need a PDF copy of your government-issued photo ID."
I had a look at the billing information and what I think is the problem is that there is a couple of problems such as the name is my full name on one form and the short version on the other. Another difference is herts and Hertfordshire same county just the short version and the long version. And finally I put my town one in caps and one not in caps.
Most of these errors are because I used shortened formats of the names there was nothing wrong with my details but it got flagged up and now it says i have to send in id i contacted support about it but they havent got back yet
what do i have to do to fix it? if i contact support and tell them that all is wrong is that the names are shortened will they let me have the dev account without haveing to spend ages sending in my id?
Thanks

If your application is held up, they have told you why and what they require to correct things, then I would say, yes, that is the ONLY way. Nothing we say here will change that - we do not speak for Apple of the Apple Developers account managers, we are just fellow users of Apple products here.

Creative Cloud Membership Error

My case number is 18006423623. I have tried contacting support several times to fix this issue. I keep getting an error message whenever I try to open my apps.
I keep getting an error message that my membership is expired whenever I try to use an app ven though I have an active subscription. Support has tried to fix this issue for me on phone and chat.
But I have gotten disconnected both times. I have uninstalled and reinstalled the Creative Cloud and the apps and still I can't use my apps. I am very frustrated with this.
I don't think it is something with my computer, but rather there is issue with my account. Can I get help with this issue, please?

This is an open forum with some Adobe staff, but mostly other users... only Adobe can help
Adobe contact information - http://helpx.adobe.com/contact.html may help

Purchasing student membership error

I am trying to purchase student membership for adobe creative cloud, yet after filling in details about school, then accepting terms for billing all I get is an error:
Page Not Found
Sorry, we couldn't find that page.
edit: At some point I had to switch creative cloud requested languege to english(which is prefered by me anyway), from czech as default.. which possibly was a little not standard way through application

We do not currently have educational pricing for the Czech Republic.

Group Membership Error

Hello,
I'm trying to implement an AWS against an Oracle database and consistently receive the following error message:
11/18/04 15:46:00- Authentication source sync agent failed to synchronize users to group '27'*** COM exception was: (0x80044fa4) [SOAP fault: faultcode='soap:Server' faultstring='System.Web.Services.Protocols.SoapException: Server was unable to process request. ---> com.plumtree.openfoundation.util.XPIllegalArgumentException: second argument is null']
I've included my source for the GetChildUsers (C#) method below:
publicPlumtree.Remote.Auth.ChildUserList GetChildUsers()
System.Data.OleDb.OleDbConnection oraAuthSource;
System.Data.OleDb.OleDbDataAdapter daGroupMembers;
oraAuthSource = newSystem.Data.OleDb.OleDbConnection("Provider=MSDAORA;Data Source=ebzd.world;User ID=dummy;Password=dummy");
String grpMemberQuery = "select u.USER_ID, u.USER_EMAIL_ADDR, u.DN_TXT from ROSTER_USER u, USER_GROUP_MEMBER gm where u.USER_ID = gm.USER_ID and u.USER_ID < 75 and gm.USER_GRP_ID = " + groupID;
daGroupMembers = newSystem.Data.OleDb.OleDbDataAdapter(grpMemberQuery,oraAuthSource);
System.Data.DataTable dtGroupMembers = newSystem.Data.DataTable();
daGroupMembers.Fill(dtGroupMembers);
ChildUser[] cuaReturnList = newPlumtree.Remote.Auth.ChildUser[dtGroupMembers.Rows.Count];
try
intgrpCount = 0;
foreach(DataRow drCurrent indtGroupMembers.Rows)
String userName = drCurrent["u.USER_EMAIL_ADDR"].ToString();
String userID = drCurrent["u.USER_ID"].ToString();
String dnText = drCurrent["u.DN_TXT"].ToString();
cuaReturnList[grpCount] = newChildUser(userName,userID,dnText);
grpCount++;
catch(Exception e)
thrownewException("There was an error retrieving the child users for Group ID: " + groupID + ". " + e.Message);
returnnewChildUserList(cuaReturnList);
The GetUsers and GetGroups work just fine. Thanks for any help in getting me through this.
Regards,
George

This error is familiar__I ran into it when I used the wrong stacks. Make sure your AWS web service is using the right SOAP Encoding Style. Document Literal for .NET and not RPC Encoded:

Cisco WLC5508 Dynamic VLAN assignment error

Hi All,
We have a HA (SSO) WLC controller pair in two DC's with the Management Interface managing the AP's. The AP's are located in the Campus LAN and the Campus and DC networks are seperated by a L3 boundary.
The plan is for one of the WLAN's to provide Dynamic VLAN Assignment via radius as a test I wanted to use the existing Management interface to bind to the WLAN, but since working through the following Document ID: 71683 one thing I noticed whilst working through the the document states that "it is required that the VLAN-ID configured under the IETF 81 (Tunnel-Private-Group-ID) field of the RADIUS server exist on the WLC"
If the above statement is true and we don't stretch VLAN's between the Campus LAN and the DC network due to the L3 boundary does this mean that Dynamic VLAN assignment won't be achievable? When testing a client connection and debugging the result I receive the following:-
*radiusTransportThread: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a [BE-resp] AAA response 'Success'
*radiusTransportThread: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a [BE-resp] Returning AAA response
*radiusTransportThread: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a AAA Message 'Success' received for mobile 10:40:f3:84:a2:2a
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[0]: attribute 11, vendorId 0, valueLen 11
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[1]: attribute 64, vendorId 0, valueLen 4
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[2]: attribute 65, vendorId 0, valueLen 4
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[3]: attribute 81, vendorId 0, valueLen 2
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[4]: attribute 8, vendorId 0, valueLen 4
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[5]: attribute 79, vendorId 0, valueLen 40
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a Received EAP Attribute (code=2, length=40,id=64) for mobile 10:40:f3:84:a2:2a
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 00000000: xxxxxx
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 00000010: xxxxxx
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 00000020: xxxxxx
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[6]: attribute 1, vendorId 9, valueLen 16
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[7]: attribute 25, vendorId 0, valueLen 25
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a processing avps[8]: attribute 80, vendorId 0, valueLen 16
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a AAA override: Dot1x Authentication PMIP Client AAA Override Enable
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a AAA override: Dot1x Authentication, default MPC configuration
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.115: [PA] 10:40:f3:84:a2:2a Tunnel-Type 16777229 should be 13 for STA 10:40:f3:84:a2:2a
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.116: [PA] 10:40:f3:84:a2:2a Tunnel-Group-Id 9 is not a valid VLAN ID for STA 10:40:f3:84:a2:2a
*Dot1x_NW_MsgTask_2: Jan 15 13:26:23.116: [PA] 10:40:f3:84:a2:2a Received Session Key from AAA Server for STA 10:40:f3:84:a2:2a.
I've sanitised some of the debug output to protect the username but the net result is no IP address assigned to the client and unable to connect to the network.
Would appreciate any guidance as to whether the Wireless Client VLAN's need to be interfaces on the WLC in order to work or whether the likes of Flexconnect could alleviate the L3 boundary?
Thanks in advance.
Kind regards,
Mark

Hi All,
After playing with Flexconnect I managed to get the dynamic vlan assignment working.
Need to create the Flexconnect Group add in the AP's to the gorup and then select the ACL Mapping tab > AAA VLAN-ACL mapping and added in the VLAN of my VLAN that my Tunnel-Group-ID (VLAN ID) had assigned to me.
Client connected and received the correct IP configuration.
Thanks
Mark

Why is trunk not showing vlan membership?

I setup corectly a LACP etherchannel with all VLANS allowed. This interface is called Po10.
Then I set up another one, Po20, consisting of interfaces 33 and 34, but this time restricting VLANs to only VLAN 20 (all config is below).
But when I do a sh int trunk and sh vlan brief, it only shows vlans for Po10. Is this because nothing is connected to the new port-channel, yet?
And what about the "no shut" command. I have not run this command. I thought I had to run this command, since all ports are shut per default in a Cisco switch? The config does not show this for any of my ports (I might have done this for the working port-channel).
Here is the config:
3750G-A#sh run int gi1/0/33
Building configuration...
Current configuration : 228 bytes
interface GigabitEthernet1/0/33
description iSCSI LACP interface
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20
switchport mode trunk
channel-group 20 mode active
spanning-tree portfast trunk
end
3750G-A#sh run int gi1/0/34
Building configuration...
Current configuration : 228 bytes
interface GigabitEthernet1/0/34
description iSCSI LACP interface
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20
switchport mode trunk
channel-group 20 mode active
spanning-tree portfast trunk
end
3750G-A#sh run int po20
Building configuration...
Current configuration : 202 bytes
interface Port-channel20
description LACP Port-Channel for VNX iSCSi
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20
switchport mode trunk
spanning-tree portfast trunk
end
3750G-A#sh int trunk
Port        Mode             Encapsulation Status        Native vlan
Po10        on               802.1q         trunking      1
Port        Vlans allowed on trunk
Po10        1-4094
Port        Vlans allowed and active in management domain
Po10        1,3,20,30,40,50,60,99
Port        Vlans in spanning tree forwarding state and not pruned
Po10        1,3,20,30,40,50,60,99
3750G-A#sh vlan brief
VLAN Name                             Status    Ports
1    default                          active    Gi1/0/6, Gi1/0/7, Gi1/0/8
                                                Gi1/0/9, Gi1/0/10, Gi1/0/11
                                                Gi1/0/12, Gi1/0/13, Gi1/0/14
                                                Gi1/0/15, Gi1/0/16, Gi1/0/19
                                                Gi1/0/20, Gi1/0/21, Gi1/0/22
                                                Gi1/0/23, Gi1/0/24, Gi1/0/25
                                                Gi1/0/26, Gi1/0/27, Gi1/0/28
                                                Gi1/0/29, Gi1/0/30, Gi1/0/31
                                                Gi1/0/32, Gi1/0/33, Gi1/0/34
                                                Gi1/0/35, Gi1/0/36, Gi1/0/37
                                                Gi1/0/38, Gi1/0/39, Gi1/0/40
                                                Gi1/0/41, Gi1/0/42, Gi1/0/43
                                                Gi1/0/44, Gi1/0/45, Gi1/0/46
                                                Gi1/0/47, Gi1/0/48, Gi1/0/49
                                                Gi1/0/50, Gi1/0/51, Gi1/0/52
3    Management                       active    Gi1/0/1, Gi1/0/2, Gi1/0/3
                                                Gi1/0/4, Gi1/0/5
20   iscsi-A                          active
30   iscsi-B                          active
40   vMotion                          active

3560-B#sh int status
Port      Name               Status       Vlan       Duplex Speed Type
Gi0/1     Management interfa notconnect   3            auto   auto 10/100/1000BaseTX
Gi0/2     management vlan 3 notconnect   3            auto   auto 10/100/1000BaseTX
Gi0/3     Mangement switch   notconnect   3            auto   auto 10/100/1000BaseTX
Gi0/4                        notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/5     VNX Management     notconnect   3            auto   auto 10/100/1000BaseTX
Gi0/6                        notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/7                        notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/8                        notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/9                        notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/10                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/11                       notconnect   1            auto   auto 10/100/1000BaseTX
Port      Name               Status       Vlan       Duplex Speed Type
Gi0/12                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/13                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/14                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/15                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/16                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/17    UCS FI-B uplinks   connected    trunk      a-full a-1000 10/100/1000BaseTX
Gi0/18    UCS FI-B uplinks   connected    trunk      a-full a-1000 10/100/1000BaseTX
Gi0/19                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/20                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/21                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/22                       notconnect   1            auto   auto 10/100/1000BaseTX
Port      Name               Status       Vlan       Duplex Speed Type
Gi0/23                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/24                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/25                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/26                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/27                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/28                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/29                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/30                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/31                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/32                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/33    iSCsi fra VNX      notconnect   1            auto   auto 10/100/1000BaseTX
Port      Name               Status       Vlan       Duplex Speed Type
Gi0/34    iSCsi fra VNX      notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/35                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/36                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/37                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/38                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/39                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/40                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/41                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/42                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/43                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/44                       notconnect   1            auto   auto 10/100/1000BaseTX
Port      Name               Status       Vlan       Duplex Speed Type
Gi0/45                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/46                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/47                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/48                       notconnect   1            auto   auto 10/100/1000BaseTX
Gi0/49                       notconnect   1            auto   auto Not Present
Gi0/50                       notconnect   1            auto   auto Not Present
Gi0/51                       notconnect   1            auto   auto Not Present
Gi0/52                       notconnect   1            auto   auto Not Present
Po10      Port-channel for U connected    trunk      a-full a-1000
Po20      iSCSi LACP Port-ch notconnect   unassigned   auto   auto

VLAN Membership with ACS

I just want to implement 802.1x authentication, to dynamically assign into differente vlans, can you help me how it should be done? What is the best method? I see the PEAP is much more complex. Initially I'm thinking about Mac-Address based, so that I create all mac-address's in ACS Server that we have, and the VLAN is assigned from there.

Excerpt from Cisco doc:-
7 Appendix C: Procedure to Configure RADIUS-Based User Access Control on Cisco
Secure Access Control Server Software
The procedure to configure RADIUS-based user access control on Cisco Secure ACS Version 2.6 or later is provided
below. This procedure provides configuration information for Internet Engineering Task Force (IETF), Cisco IOS
Software and Cisco PIX? Firewall options that enable RADIUS-based user access control (using VLAN-ID and/or
SSID-list).
1. Select Interface Configuration > Advanced Options; Enable ?Per-user TACACS+/RADIUS Attributes? > Click
on ?Submit.?
2. Select Interface Configuration > RADIUS (IETF).
a. Enable IETF attributes 64, 65, and 81. Enable these options at both User and Group levels.
b. Click on ?Submit.?
3. Select Network Configuration:
a. Confirm that the following option is available on the Cisco Secure ACS: Configuration > RADIUS (Cisco IOS/
PIX). If this option is not available, add a device with network access server-type RADIUS (Cisco IOS/PIX).
This device is needed to enable Cisco IOS/PIX attributes.
b. After adding a Cisco IOS Software or Cisco PIX Firewall device, select Interface Configuration > RADIUS
(Cisco IOS/PIX):
i. Enable the ?[026/009/001] cisco-av-pair? option. Enable this option at both User and Group levels.
ii. Click on ?Submit.?
"You want option B here"
4. Add a User (User Setup > Add/Edit).
a. To restrict user by VLAN-ID:
? Enable and set IETF 64 (Tunnel Type) to ?VLAN.?
? Enable and set IETF 65 (Tunnel Medium Type) to ?802.?
? Enable and set IETF 81 (Tunnel Private Group ID) to VLAN-ID.
Note: Use the same Tag numbers (example: Tag 1) for all the above parameters.
b. To restrict user by SSID (note: SSID is case-sensitive):
? Enable and configure Cisco IOS/PIX RADIUS Attribute, 009\001 cisco-av-pair
? Example: ssid=LEAP_WEP

Membership error on creative cloud

Hi,
i have problem with adobe Creative cloud i am getting the below error message while opening any of the adobe creative cloud products like photoshop, illustrator etc. can you plese help me some buddy on this.
Note this will be an lincenced version.
Thanks
Shekar

Hi Shekar,
I checked your Adobe account and it seems that your current Creative Cloud for Team subscription is cancelled and your ID is not associated with any other Creative Cloud subscription.
I would suggest you to consult your Primary account holder.
Thanks,
Ratandeep Arora

How to solve "We are having trouble verifying your membership" error?

Hi,
Recently, I just uninstall Creative Cloud which the trial period going to expire soon, then I re-install CS6 back which we have 3 licenses in total. Now, only one user meet with this problem, which once open Dreamweaver or Indesign software, the above error message pop up. As it's counting down the days remaining, so wonder if the days remained ends, what will affected?

Hi ,
You can try this step . Go to C Drive > Program Data ( You need to un-hide this by going to Organize and then view and then show hidden folders ) > Move SL Store to the desktop. And then launch the program and then try the above steps. Else give permissions to the adobe folder( C Drive > Program file X 86 > Right Click on Adobe Folder > Properties > Security > Edit > Select Every Username and Select full control and Check allow ). And Apply and OK.

VLAN Membership Confusion

I have a RV220 installed in a local non-profit. Each of the 4 ports was assigned to a different VLAN, each of which had it's own subnet and DHCP configuration. Each of the ports is connected to a switch, 3 smaller generic switches and one large 24 port switch.
This morning I needed to change one of the port assignments. Unfortunately, the user interface has changed and I cannot understand how to keep the 4 ports isolated to specific VLANS? Based on what I am seeing, each VLAN can be configured as tagged or untagged for each port. How do I configure this to relate each port to a specific VLAN so that the correct subnet and DHCP rules can be applied?
Thanks in advance for your help!
Dave

Hi David, if your goal is to have 4 separate subnets and those subnets not communicating to one another then the router should be configured for 1 vlan to each port.
As example port 1 is vlan 1 untagged
Port 2 is vlan 2 untagged
Port 3 is vlan 3 untagged and so forth....
Additionally, there is an option for inter-vlan communication, which should be disabled if you wish for those vlans to be isolated from one another.
Lastly, the switches connected don't need anything special so long as those switches are not interconnected. The switches connect to each router port but not to each other.
This will achieve 4 different subnets only communicating to the subnet they belong to and the internet.
-Tom
Please mark answered for helpful posts

VLAN Membership Error

Similar Messages

Maybe you are looking for