Voip between cisco and avaya

We have to implement Voice over IP on our IPLC circuit between foreign office and India office.
Topology is such that our foreign office is having 1700 series router with wan card
(Wic-1T) and one two port FXO card connected to PBX for PSTN and local connectivity.
India end we have a cisco 1700 router with wan card (Wic-1T) and on lan we have Avaya S8300 media server with multiple phones connected to it. Avaya server is acting as a voice gateway at India end. Avaya server is connected to LAN on Ethernet.
We have configured IPSEC site-to-site VPN between both the locations.
Requirement:-
Over the VPN tunnel we want to enable voice communication between both the locations.
i.e between cisco at foreign end and avaya server at India end.
1) India office users via IPLC should communicate over voice and data with the foreign office (Avaya extensions to FXO in Foreign office).
2) Foreign office should communicate with the india office users connected to IPLC link (FXO to Avaya server extensions)
Any suggestions/config will be appreciated
Attaching the india end router config.
Thanks

Hi
Before getting onto the requirements,from now on i would suggest you to mask the ip (public) address part included in the configs while posting in any general forum.
These are the links which you can use up here for the ref..
You need to check out for the possible codes and other compatible points which you need to configure on both the sidees..
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a008009431b.shtml
http://www.cisco.com/en/US/products/hw/routers/ps259/products_configuration_guide_chapter09186a008007e606.html
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a0080080afd.html
i m not sure though about the configuration of Avaya box but you can mention the remote end routers ethernet ip as the destination ip or the target for the call termination.
And in the remote router while configuring the dial-peer pots and dial-peer voip binded on the FXO itnerface make sure that you are mentioning the Avaya box ip as the session target.
regds

Similar Messages

Link Local BGP peering between Cisco and Juniper (M-Series)

Hi,
has anybody successfully managed to get a working IPv6 session between a Cisco and a Juniper router using Link Local IPs?
I got it working between two cisco routers and two Juniper Routers but not with the two different vendors.
Configuration on the Juniper site:
   family inet6 {
       address FE80::1/64;
protocols {
      bgp {
          group customer_ipv6 {
              neighbor fe80::2 {
                  local-interface at-2/0/0.119;
                  peer-as 65300;
                  as-override;
Configuration on the Cisco site:
interface ATM0/0/0.1 point-to-point
bandwidth 2033
ip address 10.194.235.42 255.255.255.252
ip access-group AL-SECURITY-WAN out
ip mtu 1500
ipv6 address FE80::2 link-local
ipv6 enable
bfd interval 999 min_rx 999 multiplier 15
pvc 1/32
vbr-nrt 2244 2244 1
tx-ring-limit 3
encapsulation aal5snap
router bgp 65300
bgp router-id 10.213.58.185
bgp log-neighbor-changes
no bgp default ipv4-unicast
neighbor FE80::1%ATM0/0/0.1 remote-as 65300
neighbor FE80::1%ATM0/0/0.1 version 4
neighbor FE80::2%GigabitEthernet0/1 remote-as 65300
neighbor FE80::2%GigabitEthernet0/1 version 4
address-family ipv4
exit-address-family
address-family ipv6
neighbor FE80::1%ATM0/0/0.1 activate
neighbor FE80::1%ATM0/0/0.1 advertisement-interval 5
neighbor FE80::1%ATM0/0/0.1 soft-reconfiguration inbound
neighbor FE80::1%ATM0/0/0.1 route-map NH6 out
neighbor FE80::2%GigabitEthernet0/1 activate
neighbor FE80::2%GigabitEthernet0/1 advertisement-interval 5
neighbor FE80::2%GigabitEthernet0/1 soft-reconfiguration inbound
neighbor FE80::2%GigabitEthernet0/1 route-map NH6 out
exit-address-family
CE_HOSTNAME# show ip bgp ipv6 uni su
BGP router identifier 10.213.58.185, local AS number 65300
BGP table version is 7, main routing table version 7
4 network entries using 656 bytes of memory
4 path entries using 320 bytes of memory
1/1 BGP path/bestpath attribute entries using 128 bytes of memory
2 BGP AS-PATH entries using 48 bytes of memory
2 BGP community entries using 48 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 1200 total bytes of memory
BGP activity 34/12 prefixes, 38/12 paths, scan interval 60 secs
Neighbor        V           AS MsgRcvd MsgSent   TblVer InQ OutQ Up/Down State/PfxRcd
FE80::1%ATM0/0/0.1
                4        65300       0       0        1    0    0 never    Idle
FE80::2%GigabitEthernet0/1
                4        65300      15      16        7    0    0 00:10:59        4
CE_HOSTNAME#
The console monitoring states the following:
Nov 10 06:30:33.023 MET: %BGP-3-NOTIFICATION: sent to neighbor FE80::1%ATM0/0/0.1 active 2/7 (unsupported/disjoint capability) 0 bytes
Nov 10 06:30:33.023 MET: %BGP-4-MSGDUMP: unsupported or mal-formatted message received from FE80::1%ATM0/0/0.1:
FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 001D 0104 505A 005A 52D2 C023 00
Nov 10 06:30:33.023 MET: %BGP-3-NOTIFICATION: received from neighbor FE80::1%ATM0/0/0.1 active 2/5 (authentication failure) 0 bytes
de-ipc-ulmdon-ce-02#
Nov 10 06:30:33.023 MET: %BGP_SESSION-5-ADJCHANGE: neighbor FE80::1%ATM0/0/0.1 IPv6 Unicast topology base removed from session BGP Notification sent
The Cisco Router is running IOS 15.2, the Juniper Site JunOS 10.4
Any Ideas how I can get this to work?
Thanks in advance!

Marcin,
I updated the debugging log, the previous one was created using override-capability-neg on the neighbor (experimental).
>>0) Do you see similar scenario for working session? (Between two Cisco routers)
The working connection between two cisco routers doesn't show any output
>>1) What verion of IOS are you running? Something failrly recent I hope?
Show Version:
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.2(1)T1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 19-Sep-11 16:24 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
CE_HOSTNAME uptime is 2 weeks, 5 days, 21 hours, 35 minutes
System returned to ROM by reload at 18:43:21 MET(S) Fri Oct 21 2011
System restarted at 18:44:50 MET(S) Fri Oct 21 2011
System image file is "flash:c1900-universalk9-mz.SPA.152-1.T1.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO1941/K9 (revision 1.0) with 446464K/77824K bytes of memory.
Processor board ID FCZ1504C0G8
1 DSL controller
2 Gigabit Ethernet interfaces
1 ATM interface
1 terminal line
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO1941/K9          FCZ1504C0G8
Technology Package License Information for Module:'c1900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
data          datak9        Permanent      datak9
Configuration register is 0x2102
>>2) Can we have some more info from Juniper side (logs/debugs).
Sadly not. The Juniper Traceoptions don't show anything
All I can offer you at this point is the neighbor show command:
user@Juniper> show bgp neighbor fe80::2 instance vrf-test
Peer: fe80::2 AS 65300         Local: unspecified AS 20570
Type: External    State: Idle           Flags:
Last State: NoState       Last Event: NoEvent
Last Error: None
Export: [ pol-standard-bgp-export ] Import: [ pol-standard-bgp-import ]
Options:
Options:
Address families configured: inet6-unicast
Path-attributes dropped: 128
Holdtime: 90 Preference: 170
Number of flaps: 0
Trace options: all
Trace file: /var/log/bgp_ipv6_ll_20111110 size 131072 files 10
user@Juniper> show bgp summary instance vrf-test
Groups: 2 Peers: 2 Down peers: 1
Table          Tot Paths Act Paths Suppressed    History Damp State    Pending
vrf-2.inet.0          37         16          0          0          0          0
vrf-.inet6.0           0          0          0          0          0          0
vrf-24.mdt.0           0          0          0          0          0          0
Peer                     AS      InPkt     OutPkt    OutQ   Flaps Last Up/Dwn State|#Active/Received/Accepted/Damped...
10.194.235.42         65300       1149       1076       0       1     8:44:00 Establ
vrf-test.inet.0: 6/7/7/0
fe80::2               65300          0          0       0       0     9:38:32 Idle
>>3)
CE_HOSTNAME#
Nov 10 15:35:49.574 MET: BGP: ses global 10.194.235.41 (0x2970EDA4:1) Keep alive timer fired.
Nov 10 15:35:49.574 MET: BGP: 10.194.235.41 KEEPALIVE requested (bgp_keepalive_timer_expired)
Nov 10 15:35:49.574 MET: BGP: ses global 10.194.235.41 (0x2970EDA4:1) service keepalive IO request.
Nov 10 15:35:49.574 MET: BGP: 10.194.235.41 KEEPALIVE write request serviced in BGP_IO
CE_HOSTNAME#
Nov 10 15:35:50.598 MET: BGP: ses global FE80::2%GigabitEthernet0/1 (0x316FBDDC:1) Keep alive timer fired.
Nov 10 15:35:50.598 MET: BGP: FE80::2%GigabitEthernet0/1 KEEPALIVE requested (bgp_keepalive_timer_expired)
Nov 10 15:35:50.598 MET: BGP: ses global FE80::2%GigabitEthernet0/1 (0x316FBDDC:1) service keepalive IO request.
Nov 10 15:35:50.598 MET: BGP: FE80::2%GigabitEthernet0/1 KEEPALIVE write request serviced in BGP_IO
CE_HOSTNAME#
Nov 10 15:35:52.850 MET: BGP: 10.194.235.41 received KEEPALIVE, length (excl. header) 0
CE_HOSTNAME#
Nov 10 15:35:54.694 MET: BGP: FE80::1%ATM0/0/0.1 active went from Idle to Active
Nov 10 15:35:54.694 MET: BGP: FE80::1%ATM0/0/0.1 open active, local address FE80::2
Nov 10 15:35:54.698 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Adding topology IPv6 Unicast:base
Nov 10 15:35:54.698 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Send OPEN
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active went from Active to OpenSent
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active sending OPEN, version 4, my as: 65300, holdtime 180 seconds, ID AD53AB9
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active KEEPALIVE write request serviced in BGP_IO
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active service 2 read request in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active KEEPALIVE write request serviced in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active service 2 read request in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active service 2 read request in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv message type 1, length (excl. header) 10
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Receive OPEN
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv OPEN, version 4, holdtime 90 seconds
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv OPEN w/ OPTION parameter len: 0
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active went from OpenSent to Closing
Nov 10 15:35:54.702 MET: %BGP-3-NOTIFICATION: sent to neighbor FE80::1%ATM0/0/0.1 active 2/7 (unsupported/disjoint capability) 0 bytes
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Send NOTIFICATION 2/7 (unsupported/disjoint capability) 0 bytes
Nov 10 15:35:54.702 MET: %BGP-4-MSGDUMP: unsupported or mal-formatted message received from FE80::1%ATM0/0/0.1:
FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 001D 0104 505A 005A 52D2 C023 00
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv message type 3, length (excl. header) 2
Nov 10 15:35:54.702 MET: %BGP-3-NOTIFICATION: received from neighbor FE80::1%ATM0/0/0.1 active 2/5 (authentication failure) 0 bytes
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Receive NOTIFICATION 2/5 (authentication failure) 0 bytes
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active bad state change from Closing to Closing
Nov 10 15:35:54.702 MET: -Traceback= 21B3370Cz 21B33C74z 21B34258z
Nov 10 15:35:54.702 MET: BGP: tbl IPv4 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl IPv6 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl VPNv4 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl VPNv6 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl IPv4 Multicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) NSF delete stale NSF not active
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) NSF no stale paths state is NSF not active
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) Resetting ALL counters.
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active closing
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Session close and reset neighbor FE80::1%ATM0/0/0.1 topostate
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) Resetting ALL counters.
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active went from Closing to Idle
Nov 10 15:35:54.702 MET: %BGP_SESSION-5-ADJCHANGE: neighbor FE80::1%ATM0/0/0.1 IPv6 Unicast topology base removed from session BGP Notification sent
CE_HOSTNAME#CE_HOSTNAME#
Nov 10 15:35:49.574 MET: BGP: ses global 10.194.235.41 (0x2970EDA4:1) Keep alive timer fired.
Nov 10 15:35:49.574 MET: BGP: 10.194.235.41 KEEPALIVE requested (bgp_keepalive_timer_expired)
Nov 10 15:35:49.574 MET: BGP: ses global 10.194.235.41 (0x2970EDA4:1) service keepalive IO request.
Nov 10 15:35:49.574 MET: BGP: 10.194.235.41 KEEPALIVE write request serviced in BGP_IO
CE_HOSTNAME#
Nov 10 15:35:50.598 MET: BGP: ses global FE80::2%GigabitEthernet0/1 (0x316FBDDC:1) Keep alive timer fired.
Nov 10 15:35:50.598 MET: BGP: FE80::2%GigabitEthernet0/1 KEEPALIVE requested (bgp_keepalive_timer_expired)
Nov 10 15:35:50.598 MET: BGP: ses global FE80::2%GigabitEthernet0/1 (0x316FBDDC:1) service keepalive IO request.
Nov 10 15:35:50.598 MET: BGP: FE80::2%GigabitEthernet0/1 KEEPALIVE write request serviced in BGP_IO
CE_HOSTNAME#
Nov 10 15:35:52.850 MET: BGP: 10.194.235.41 received KEEPALIVE, length (excl. header) 0
CE_HOSTNAME#
Nov 10 15:35:54.694 MET: BGP: FE80::1%ATM0/0/0.1 active went from Idle to Active
Nov 10 15:35:54.694 MET: BGP: FE80::1%ATM0/0/0.1 open active, local address FE80::2
Nov 10 15:35:54.698 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Adding topology IPv6 Unicast:base
Nov 10 15:35:54.698 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Send OPEN
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active went from Active to OpenSent
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active sending OPEN, version 4, my as: 65300, holdtime 180 seconds, ID AD53AB9
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active KEEPALIVE write request serviced in BGP_IO
Nov 10 15:35:54.698 MET: BGP: FE80::1%ATM0/0/0.1 active service 2 read request in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active KEEPALIVE write request serviced in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active service 2 read request in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active service 2 read request in BGP_IO
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv message type 1, length (excl. header) 10
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Receive OPEN
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv OPEN, version 4, holdtime 90 seconds
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv OPEN w/ OPTION parameter len: 0
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active went from OpenSent to Closing
Nov 10 15:35:54.702 MET: %BGP-3-NOTIFICATION: sent to neighbor FE80::1%ATM0/0/0.1 active 2/7 (unsupported/disjoint capability) 0 bytes
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Send NOTIFICATION 2/7 (unsupported/disjoint capability) 0 bytes
Nov 10 15:35:54.702 MET: %BGP-4-MSGDUMP: unsupported or mal-formatted message received from FE80::1%ATM0/0/0.1:
FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 001D 0104 505A 005A 52D2 C023 00
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active rcv message type 3, length (excl. header) 2
Nov 10 15:35:54.702 MET: %BGP-3-NOTIFICATION: received from neighbor FE80::1%ATM0/0/0.1 active 2/5 (authentication failure) 0 bytes
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Receive NOTIFICATION 2/5 (authentication failure) 0 bytes
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active bad state change from Closing to Closing
Nov 10 15:35:54.702 MET: -Traceback= 21B3370Cz 21B33C74z 21B34258z
Nov 10 15:35:54.702 MET: BGP: tbl IPv4 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl IPv6 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl VPNv4 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl VPNv6 Unicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: tbl IPv4 Multicast:base Service reset requests
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) NSF delete stale NSF not active
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) NSF no stale paths state is NSF not active
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) Resetting ALL counters.
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active closing
Nov 10 15:35:54.702 MET: BGP: ses global FE80::1%ATM0/0/0.1 (0x296337B4:0) act Session close and reset neighbor FE80::1%ATM0/0/0.1 topostate
Nov 10 15:35:54.702 MET: BGP: nbr_topo global FE80::1%ATM0/0/0.1 IPv6 Unicast:base (0x296337B4:0) Resetting ALL counters.
Nov 10 15:35:54.702 MET: BGP: FE80::1%ATM0/0/0.1 active went from Closing to Idle
Nov 10 15:35:54.702 MET: %BGP_SESSION-5-ADJCHANGE: neighbor FE80::1%ATM0/0/0.1 IPv6 Unicast topology base removed from session BGP Notification sent
CE_HOSTNAME#

Trunk between cisco and huawei

One of my edge Huawei S5700-28C-EI stack switches is dead, I am going to replace it with a Cisco switch Catalyst 3750 series PoE-48 via a trunk link with GE fiber port on both ends, please see the diagram below.
                                  trunk                     trunk
   Core switchrouter<----------S5700<--------------->Cisco Catlyst 3750
I haven’t touch Cisco switch for many years, I would like to ask the following questions:
1.)      Do I need to take any precaution before connecting this Cisco switch into my Huawei network? Only one link between S5700 and C3750, so I don't need worry anout STP? Do I need to worry about Default vlan regarding trunking port?
2.)      I need to use different trucking protocol e.g. 802.1Q etc to interconnect these two switches (S5700 and Catalyst 3750), please see the following configuration:
For C3750:
switchport trunk encapsulation dot1q
switchport trunk native vlan (What you want)
switchport trunk allowed vlan (VLANs required)
switchport mode trunk
spanning-tree portfast trunk
For S5700:
port link-type trunk
port trunk permit vlan all
Do you think the configurations above are right?
Do I need to manually enter Duplex and speed options ?
3.)If the configurations are not right, then what are the commands for trucking port/link should I use on the Cisco switch (it uses IOS software) and Huawei switch? Procedures of the commands would be really helpful !
Any information and help would be much appreciated.

I know the problem,When I change the native vlan of my S5700-28C-EI ,it's just ok.

Multicast Cisco and Avaya

I hv Avaya P882 as core,Cisco cat4507 as distribution and cat3750 access. There are a video in Avaya P882 configure multicast. PC attach to Avaya can receive video stream but PC at Cisco cat4507 and cat3750 cannot receive video stream from avaya P882. my understanding avaya P882 only support DVMRP. Any advice how to configure on Cat4507 and Cat3750. did i need ip mroute?

you can configure IOS to use DVMRP for interoperability between systems.
please see the following link for more DVMRP interoperability and configuration info:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca79c.html

Problem with old VoIP between modem and Time Capsule

Hi, I hope someone can help me with this..
For a job I used to have, I had a D-Link DVG-5102S VoIP adapter/router that I had to have between my Motorola DSL modem and my Time Capsule WiFi.
The service that the D-Link was used for has been shut off for a long time, but I don't seem to be able to get rid of it. When I remove it, and try to re-configure things on the Time Capsule so that it has the DSL login info, my internet access stops working.
Currently, the D-Link has the DSL login info, and distributes 192.168.15.x addresses to the Time Capsule.
The Time Capsule has the following info:
Base Station tab:
Base station name, password, Back to my Mac account/password
Internet tab:
Connect using: DHCP, IP Address 192.168.15.160, subnet mask 255.255.255.0, Router address 192.168.15.1, Primary DNS Server 192.168.15.1
Wireless tab:
Create a Wireless network, Wireless network name <my WiFi network>, Wireless SEcurity WPA2 Personal, Wireless Password/Verify Password
Network tab:
Router Mode: Off (Bridge Mode)
Everything else is greyed out
Disks:
My time capsule backup disk.
Does anyone have any ideas for how I should go about getting rid of that stupid VOIP thing?
Thanks!

Your DSL modem has probably locked on to the D-Link box's MAC address. Since the TIme Capsule has a different MAC address than the D-link, the DSL modem doesn't know what to do with it.
(MAC address btw has nothing to do with Mac computers - it is an alphanumeric address that is assigned to each and every networking device that's made - yes, including Mac computers.)
Usually turning the DSL modem off and back on should reset it, and the next device that it talks to (hopefully the Time Capsule) will become its new best friend (i.e. it will "remember" the Time Capsule's MAC address). Some DSL modems have a setup page (or setup software) that you must run, to give it a new MAC address. And sometimes only your DSL provider can do this for you (they reset something on their end or something like that). If turning the DSL modem off then on again doesn't do the trick, and your modem either doesn't have a setup application (or you don't see a setting for MAC address), then you'll have to call your provider. Tell them that you switched the device that the modem is plugged into, and they should be able to help you out (theoretically anyway, your actual customer service drone experience may vary).

VoIP between Norstar and Nortel option 11

Hi, i have some problems in the calls between a Norstar and a Nortel option 11, both are connected to a 2811 via E1 with the IOS is c2800nm-spservicesk9-mz.124-15.T3.bin both routers are using h323. We also have a Callmanager 5.1.2.3000-2 that interact with both PBX.
The problem is that when i make a call from the Norstar to the Nortell or CCM the call listens choppy and sometime the voice goes only one side.
Do you know of some debug that i can apply to see ISDN errors, h323 errors, or QoS errors.
Thanks in advanced
Jose

Well the IAD is configured for E&M immidiate which is completely different from R2 even though they are both a way to do CAS.
http://cisco.com/en/US/tech/tk652/tk653/tk755/tech_protocol_home.html
E&M:
http://cisco.com/en/US/products/sw/iosswrel/ps5207/products_configuration_guide_chapter09186a008020ecf6.html#wp1021994
R2:
http://cisco.com/en/US/tech/tk652/tk653/technologies_configuration_example09186a00800ad389.shtml
http://cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800942f2.shtml

Compatible between Cisco and Huawei

Dear Expert
We have purchased 7 units Huawei access switches, S2700-26TP-EI-AC & 1310 SFP modules from www.huanetwork.com now we plan to add a aggregation switches, for this part, we want to use Cisco WS-C3750X-24S-S, my question is with Huawei GE optical port (with 1310 SFP module), can it connect to Cisco 3750X GE ports (with GLC-LH-SMD). If not we may need to go for Huawei S5700.
Thanks very much.

I know the problem,When I change the native vlan of my S5700-28C-EI ,it's just ok.

Cisco BE6K and Avaya Aura Midsize Enterprise Comparison

Hi everyone,
As my subject above,
does anyone have product comparison between Cisco Business Edition 6000 (BE6K) and Avaya Aura Midsize Enterprise Comparison?
Please help and send it to [email protected] if you already have it,
Thanks,
Ovindo

You probably want to reach your SE/AM for this kind of info.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

Routing issue between Cisco Nexus and Cisco 4510 R+E Chassis

We have configured Cisco Nexus 7K9 as core and Cisco 4510 R+E as access switches for Server connectivity.
We are experiencing problem in terms of ARP learning and Ping issues between Cisco Nexus and end hosts.

Hi,
So you have N7k acting as L3 with servers connected to 4510?.
Do you see the MAC associated with failing ARP in 4510?. Is it happening with all or few servers?. Just to verify if it is connectivity issue between N7k and 4510, you can configure an SVI on 4510 and assign address from same raneg (server/core range) and perform a ping.
This will help narrow down if issue is between server to 4510 or 4510 to N7k.
Thanks,
Nagendra

Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: end

Thanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.

The difference of the IEEE802.1x Auth between Cisco Routers and Catalyst switches

Hello
I am investigating the difference of the IEEE802.1x Auth between Routers and Switches.
Basically dot1x auth is availlable on Catalyst Switches. however if I want to check to
PortBased Multi-Auth , MAC address Auth and any certification Auth with this feature,
Is it possible to integrate into Cisco Router such as Cisco 891F ?
In my opinion Cisco891F is also available to use basic IEEE802.1x but if it compares with Catalyst switches such as Cat3560X
I think there might be any unsupported feature on Cisco 891F.
I appreciate any information. thank you very much in advance.
Best Regards,
Masanobu Hiyoshi

Many time in interviews asked comaprison between cisco routers and switches that i was answerless bcoz i dont have much knowledge about that.Can anyone provide me the compariosin sheet of the same.how are the cisco devices differ with each other how much Bandwidth each routres support and Etc...
Ummmm ... The most common question I get is "what is the difference between a router and a switch".
However, if you get a question like this, then my impression to this line of questioning are:
1. The candidate they are looking for has in-depth knowledge of routers and switches. And I mean IN-DEPTH!;
2. They are not looking for a candidate. They just want to stroke their ego. There is not alot of people who can give you the "names and numbers" of routers and switches at a snap of a finger. And if you do happen to know the answer, then and there, then expect a tougher follow-up question.

Is there any documentation to deploy federation between Cisco IM and presence and Lync 2010 sister companies?

Hello All,
Company A – Using Cisco IM and Presence
Company B – Using Microsoft Lync 2010
We would like to establish federation between Company A and Company B and also looking for the documentation which has the step by step instruction.
Please let us know overall steps or provide us the documentation. Thank you in advance.
Thanks

For Federation between Lync and Cisco IM, you can check below link and this
document
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/im_presence/interdomain_federation/9_0_1/CUP0_BK_IAAE17D8_00_integration-guide-interdomain-federation-90/CUP0_BK_IAAE17D8_00_integration-guide-interdomain-federation-90_chapter_01.html
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

Inline Posture between Cisco ISE and Wireless LAN Controller

Hi,
I was looking into Cisco ISE solution for deploying NAC.
I have a question about the network topology.
In the user guide documents of cisco ISE, it is written that for Wireless LAN Controllers (WLC) and VPN devices, an additional server, Inline Posture, is needed.
However, in the following integration document, there is not an inline posture between WLC and Cisco ISE server.
https://supportforums.cisco.com/docs/DOC-18121
I want to know if Inline Posture is a requirement, if not a requirement, what are the benefits of having it between Cisco ISE Server and WLC.
Thanks & Regards
Sinan

Hello,
Please go through below mentioned links which might be helpful for you.
http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_ipep_deploy.html
http://www.cisco.com/en/US/docs/security/ise/1.2/installation_guide/ise_deploy.html
Best Regards,

What is the difference in the features between Cisco prime 1.2 and Cisco prime 1.4 ?

Dears,
Please i need to know what is the difference in the features between Cisco prime infrastructure 1.2 and Cisco prime 1.4.
Already i see the release note for each one but the release indicate only the New feature for every one. so i need to know the difference between them not new features.
Wait your kind feedback plz
Regards,

Hi,
New Features and Enhancements
The following topics describe new features and enhancements in Cisco Prime Infrastructure 1.4.
Management Support for WLC Release 7.5
Support for 802.11ac Module
Support for Cisco AP 700
Policy Classification Engine
FlexConnect Audit Support
Autonomous AP Support
Client Stateful Switchover
Cable Modem Monitoring
Support for Secure File Transfer Protocol
and please go through the link and check the data sheet for further clearance.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/datasheet-c78-729879.html

Voip between cisco and avaya

Similar Messages

Maybe you are looking for