WAAS VLAN - not all traffic is being forwarded to WAE

Hi, I've configured a WAAS topology based on this Cisco document
(http://www.cisco.com/application/pdf/en/us/guest/netsol/ns377/c649/ccmigration_09186a008081c7da.pdf)
where the WAE's are in their own VLAN and there is a trunk between the 2 edge routers and 2 6509 switches (the WAE's connect to this switch). Both the "data" vlan and the WAAS vlan is participating in EIGRP which means that traffic is being routed over both sub-interfaces. The problems is that one of the sub-interfaces has the "ip wccp redirect exclude in" command configured so only half the traffic will be passed to the WAE's. Has anyone come across this before? Should I be removing the WAAS vlan from EIGRP and using the second interface on the WAE for management in a seperate subnet?
interface GigabitEthernet0/0
description Trunk link to 6500
no ip address
interface GigabitEthernet0/0.901
description WAN Edge VLAN
encapsulation dot1Q 901 native
ip address 10.7.7.2 255.255.255.224
ip wccp 61 redirect in
ip wccp 62 redirect out
interface GigabitEthernet0/0.902
description WAAS VLAN
encapsulation dot1Q 902
ip address 10.7.9.1 255.255.255.240
ip wccp redirect exclude in
standby 1 ip 10.7.9.3
standby 1 timers 1 3
standby 1 priority 110
standby 1 preempt delay minimum 1
standby 2 ip 10.7.9.4
standby 2 timers 1 3
standby 2 priority 120
standby 2 preempt delay minimum 1
Edge_Router#sh ip ro 10.6.1.181
Routing entry for 10.6.1.0/21
Known via "eigrp 1", distance 90, metric 28928, type internal
Redistributing via eigrp 9
Last update from 10.7.7.1 on GigabitEthernet0/0.901, 08:18:01 ago
Routing Descriptor Blocks:
10.7.7.1, from 10.7.7.1, 08:18:01 ago, via GigabitEthernet0/0.902
Route metric is 28928, traffic share count is 1
Total delay is 130 microseconds, minimum bandwidth is 100000 Kbit
Reliability 245/255, minimum MTU 1500 bytes
Loading 12/255, Hops 3
* 10.7.9.1.2, from 10.7.9.1.2, 08:18:01 ago, via GigabitEthernet0/0.901
Route metric is 28928, traffic share count is 1
Total delay is 130 microseconds, minimum bandwidth is 100000 Kbit
Reliability 245/255, minimum MTU 1500 bytes
Loading 12/255, Hops 3

BRADLEY,
In this case you should make the data VLAN passive (from an EIGRP perspective) and use the WAE VLAN as a transit between the two routers. You don't want traffic coming in from the WAE VLAN to get re-intercepted.
Zach

Similar Messages

  • JLayeredPane - not all high layer being drawn.

    I'm getting an odd effect with a JLayeredPane in that some (but not all) of a higher layer is being hidden behind a lower layer JComponent. Is this likely to be a layout manager issue (I'm not setting one) or am I doing something else silly?
    I'd have posted some code, but the highly simplified case that I first wrote works OK, and I can't quite see the difference between it and my program. It'll take at least another day to simplify that one to make it postable. So I thought I'd ask the general question first.

    Forgive me if this counts as highjacking an old thread. Did you ever find a solution, and what was it?
    I kinda have the opposite problem: I have two JPanels in a JLayeredPane and put the relevant one of them in front depending on the situation. But when the one conatining a JList is behind, if I click where the JList is, the selected element of the list comes to front even though I don't think it should, and also some JButtons when the mouse comes over them.
    I'll ask a colleague who has more experience with JLayeredPane than I have. If I find a solution, I'll post it here. Should be glad to hear from anyone who might know anything about the problem.

  • Has Mountain Lion solved the issue of not all sent emails being saved?

    The Snow Leopard forum has a thread about Mac Mail not saving every sent item in the "Sent" folder. My email account is IMAP and it seems to work fine for most of the time except that, every now and again, a message is sent (and it really is sent) but never appears in the "Sent" folder on either my Mac Mail or the synched folder on my ISP server. This seems to happen when a message takes a long time to get to the end of the activity bar before the usual "whooshing" sound and it has been suggested that the delay causes Mac Mail to delete the message. The SL forum left the issue unresolved but I have not seen any reports of the problem being there on ML so wonder if it has been fixed and my problem lies with my ISP rather than my iMac. Has anyone else experienced this problem on ML?

    My primary email account is IMAP and I have just found what I suspect are all the messages that were not saved in my "sent" folder either on my iMac or ISP server. They were in the "Sent" folder of my secondary, little-used Hotmail account and the recipients "saw" these as originating from this account rather than the one from which I actually sent them. After some testing, I discovered that, for my primary account, the "always use this server" box was not checked. I surmise that, if the Mail app has trouble using the server associated with my primary account, it simply uses the Hotmail server (this would be consistent with the delay before hearing the "whooshing"noise). What does surprise me is that, if this Hotmail server has been used, the recipient sees the message as originating from Hotmail. Is this what is supposed to happen?

  • TS3989 Not all photos are being pushed to my photo stream folder on computer?

    So this was working right for a while and now its not doing so well. Some pictures are being uploaded but now they arent uploading.. HELP!!!

    Try disabling photo stream on your device (settings > iCloud), restarting your device and then re-enabling photo stream.
    If this doesn't help you may need to reset photo stream. You can do this at icloud.com by clicking on your name in the top right corner and then the advanced settings in the pop-up dialogue box that appears.

  • Not all photos are being published to Smugmug

    LR5 will not publish all of my photos to Smugmug. I get a message that LR failed to export some files. Can anyone help?

    Would it be possible to furnish some more info?
    e.g. versions of OS, Lr, and which SmugMug plugin & version.
    Anything that would help shed light, e.g. have you tried exporting the same photos and/or a larger set of photos to hard disk? what about using ftp plugin, or another smugmug plugin...
    I mean, lots of people export their photos to smugmug without issue, so to know what's going on in your case, it would help to define your "case".
    Screenshot of error dialog?
    Always the same photos? random? percent failed?
    etc.
    I mean, maybe somebody will come along with a magic bullet you can use, and you won't have to go through any of that, but in the mean time... - it might help.
    Rob

  • Will not all me to fast forward/remind in songs

    Sometimes while using the iPod Touch I'll try to fast forward or rewind in a song, and the iPod allows me to drag the cursor, but then does not change places in the song. If I then touch to get rid of the placement bar and then make it come back, the cursor is back where it began. If I restart the iPod by going to settings, then it will allow me to fast forward or rewind again. However, sometimes again it will not allow me to change place in my songs. It's as if it allows me to place where I want to be, but does not register the result. Any ideas?
    Thanks much in advance

    mine does the same thing if i try to pause music

  • Not all email's being downloaded

    Hi
    My most recent email's are being downloaded from the past few days, but not old ones that are stored on the server.
    OS - Windows 7
    Email client - Windows live Mail, Version 2011 Build 15.4
    Error Quote - Unable to send or receive messages for the XXXXXXX account. Your server has unexpectedly terminated the connection. Possible causes for this include server problems, network problems, or a long period of inactivity.
    Server: 'mail.btinternet.com' Windows Live Mail Error ID: 0x800CCC0F Protocol: POP3 Port: 110 Secure(SSL): No
    Any help would be greatly appreciated.
    Mark

    Login to webmail, you probably have an e-mail with a large attachment which cannot be downloaded.
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Not all files copy on to DVD/CDs

    hello. i have a macbook running OS 10.5.8
    i need some help...
    when i burn a DVD or CD to back up files, not all files are being burned. about 50% are burned.
    any thoughts?
    thanks!

    Best suggestions are:
    1) Lower the Burn speed from Best to 2-4x
    2) Try a different brand of media
    3) Run a DVD Lens Cleaner disc through it

  • Some (not all) updates to playlist show up on mini

    I created a new playlist and a new smart playlist in itunes, that doesn't show up on my ipod... I also deleted the on-the-go playlist, and that still shows up on the ipod, so theres obviously a problem w/ the updating. But I've also added new songs on an existing playlists, and they are showing up on the ipod, so not all updates are being affected. Any ideas? Should I reset?

    Yeah, try to reset
    Press and hold the MENU and CENTER buttons at the same time until you see the Apple logo on your screen, then release those buttons. Try to do this while your iPod is plugged into your computer. Do you have your iPod set to manually or automatically update itself? For example, mine updates automatically..as soon as I plug it in my iPod automatically updates all my new songs without me clicking on anything.

  • TS1372 ipod Error (-69) NOT ALL SONGS DOWNLOADING???

    my ipod has been crackling and getting "stuck" of late, error message (-69) coming up, tried restore ipod and reload songs onto it, error still remains? also not all songs are being downloaded onto ipod, any ideas?

    Have you seen this Apple support document?
    iTunes displays a -69 error when syncing iPod
    B-rock

  • WINS traffic not being forwarded

    Hi folks,
    For some reason, it seems that my WINS traffic isn't being forwarded across subnets over our 3750's. This is causing the workstations to have a "hit and miss" with authentication. I have enable "ip helper-address", "ip forward-protocol udp 137/138", even tried "ip directed-broadcast".
    If I create create an LMHOST file, it works everytime. "Enable NetBIOS over TCP/IP" is enable on WinXP Clients. On Win98 clients receives it's setting from dhcp.
    PCa---Vlan1 --<>-- Vlan2 ---- WINS Server / Authentication
    Thanks..
    -- Dominique

    Hi Everyone,
    This is how I have the device currently configured:
    <..snip..>
    ip dhcp excluded-address 10.203.8.1 10.203.8.29
    ip dhcp pool 10.203.8.0/24
    network 10.203.8.0 255.255.255.0
    default-router 10.203.8.1
    dns-server 10.70.0.9 10.70.0.6
    domain-name rainbowschools.ca
    netbios-name-server 10.203.0.7
    netbios-node-type h-node
    <..snip..>
    !! Example Interface Configuration !!
    interface FastEthernet1/0/23
    description Academic
    switchport access vlan 108
    switchport mode access
    no cdp enable
    spanning-tree portfast
    !! Server VLAN interface !!
    interface Vlan100
    ip address 10.203.0.1 255.255.255.0
    !! Academic VLAN interface !!
    interface Vlan108
    ip address 10.203.8.1 255.255.255.0
    ip helper-address 10.203.0.7
    ip directed-broadcast
    !! IP Forward Protocol !!
    ip forward-protocol udp netbios-ss
    ip forward-protocol udp bootps
    ip forward-protocol udp bootpc
    --> Even when I enter "ip forward-protocol udp 137/138", it doesn't appear. So I am assuming it is on by default.
    Thanks.
    -- Dominique

  • Calls not being forwarded to skype number

    Hello, I have had my Skype number for 2 years now and never had a problem.However since end of November 2012 calls from the USA are no longer being forwarded to my cellphone in Germany.No , I have not changed my settings , why should I , since it has been working perfectly all these years.There is no way to get help from Skype and I am extremely frustrated with their service.It sucks to pay for a product that won´t work.I am a dissatisfied customer and will leave them if they do not straighten out their stuff.

    watsource wrote:
    Hello, I have been a SKYPE user for the past 5 years and everything has been working fine.  Recently, calls from telephones to my skype number are not being forwarded to my designated number.  I've tried to turn off and on forwarding feature but still not working. Calls from other skype contacts using skype calling me are forwarded but not from any landline or mobile contacts calling my skype number.
    What happens when you call your Online Number? 
    If calls directly from other Skype users are being forwarded to your designated number, but not the calls made to your Online Number, call-forwarding appears to be working.  You may have a different issue related to your Online Number. Has it expired?  If you click on "Account" at the top of this page, you can verify that your Online Number is still in effect by clicking on "Online Number" once you log into your Skype account through that link.
    If your Online Number is still in effect, here's something else to check.  From a computer (not the Skype app on a mobile phone or other device), can you verify the Privacy setting for Online Numbers?  It should be set to allow calls from anywhere.  If not, it is possible that this setting was changed, preventing you from getting calls on the Online Number. 
    Patrick
    Location/Ubicacion: Arizona USA
    Time Zone/Hora Local: UTC/GMT -7
    If this message has adequately addressed your issue, please click on the “Accept as Solution” button. If you found a post useful then please "Give Kudos" at the bottom of my post, so that this information can benefit others.
    Si esto mensaje le ha ayudado, por favor haga clic en "Aceptar como solución". Si encuentra un mensaje útil, por favor "Da Kudos" al final del mensaje, por lo que esta información puede beneficiar a otros.
    I am not a Skype employee. No soy un empleado de Skype.

  • SPAN VLAN cannot see all traffic

    I'm capturing traffic with wireshark and when I capture a VLAN all I see is the source VLAN and destination is broadcast. Why do I not see traffic to other vlans? I would think I would see traffic from the VLAN going to the server VLAN (exchange, file servers, ect) and internet traffic. 
    Here is how I have the SPAN configured. The switch is a 2960-x
    Session 1
    Type                     : Local Session
    Source VLANs             :
        Both                 : 110
    Destination Ports      : Gi2/0/15
        Encapsulation      : Native
              Ingress      : Disabled

    Hi,
    Vlan SPAN only monitors traffic that leaves or enters Layer 2 ports in the VLAN, you will not see routed traffic.
    Hope this helps 

  • My computer crashed. So does this mean I can not add any more music to my ipod from a different computer without all the songs being erased? Can I sync my ipod to a new computer if I allow all the songs to be erased?

    My computer crashed. So does this mean I can not add any more music to my ipod from a different computer without all the songs being erased? The ipod works fine and now i got a new computer. So it seems like my only options are leaving my ipod in a state where i cant add anymore songs or erasing all my songs and trying to use my ipod from my new computer. Can someone please inform me on how to have my ipod work from a different computer, even if i have to erase my songs. Thanks.

    Yes, if you choose the Erase and Sync option (or restore your iPod) you will be allowed to sync your iPod with the new computer.
    If you would like to save the content that's currently on your iPod, see this older thread from another forum member Zevoneer discussing the different ways to copy the content on an iPod back to your PC.
    https://discussions.apple.com/thread/2417169?start=0&tstart=0
    B-rock

  • VOIP calls not being forwarded from GW to GK and visa versa

    I have a VOIP network setup in place using 2691 routers. i have a siemens PBX connected to the 2691 routers using an E1 controller (running QSIG), my WAN interface between the two sides is an ATM interface. when i do a csim start from one router to the extension on the other side the call goes through and the phone rings. However, when i actually dial from one extension to the other, the call is not being forwarded. and what happens is that i hear the dial tone again on the phone im dialing from.
    I have taken some debugs but still could pin point the problem, even though in the ccapi inout debug i found that when it tries to look for a node, it doesnt find it.
    I have attached the configuration for both sides. Along with the debug from one of the sites.
    There are a couple of GW's associated with the GK.
    The ones im concerned about are Mussalla_GW & GK-HO.
    Thank You in advance
    Mouhannad

    Try this:
    dial-peer voice 2 pots
    direct-inward-dial
    Without this command the router will not collect the digits coming across the PRI.
    Please rate helpful posts.

Maybe you are looking for