Wget error

Hi:
I am getting following error:
[root~]# wget http://public-yum.oracle.com/public-yum-ol6.repo
--2013-06-03 08:49:44-- http://public-yum.oracle.com/public-yum-ol6.repo
Resolving public-yum.oracle.com... failed: Temporary failure in name resolution.
wget: unable to resolve host address “public-yum.oracle.com”
[root~]#
I tried all that is posted on internet but in vain.
While installing Oracle Linux 6, I skipped the network configuration step. Not sure if this is the error.
Internet is not working on this OEL 6 on vmware on windows7. However, Internet is working fine using the same wireless connection on Windows 7.
Please help me fix this ASAP.
Regards n thanks!
SAmiullah

Hi Dude:
Thanks for the initial insight into the problem but it is still there. I followed your guidelines and then ran wget still the same error:
[root@ yum.repos.d]# ifconfig eth0 up
[root@ yum.repos.d]# service network restart
Shutting down interface eth0: [  OK  ]
Shutting down loopback interface: [  OK  ]
Bringing up loopback interface: [  OK  ]
[root@ yum.repos.d]# vi /etc/sysconfig/network-scripts/ifcfg-eth0
[root@ yum.repos.d]# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:480 (480.0 b) TX bytes:480 (480.0 b)
[root@ yum.repos.d]#
[root@ yum.repos.d]# wget http://public-yum.oracle.com/public-yum-ol6.repo
--2013-06-04 05:23:24-- http://public-yum.oracle.com/public-yum-ol6.repo
Resolving public-yum.oracle.com... failed: Temporary failure in name resolution.
wget: unable to resolve host address “public-yum.oracle.com”
[root@ yum.repos.d]#
From the ifconfig output above its clear that eth0 is not detected. Well, I am on a wireless network and it set to be detected automatically. Its quite strange that I was able to access the yum repository in RHEL6.4 but in OEL6 its not working. I had not done anything specific for RHEL64.
This is my /etc/resolv.conf entry
# Generated by NetworkManager
search com
# No nameservers found; try putting DNS servers into your
# ifcfg files in /etc/sysconfig/network-scripts like so:
# DNS1=xxx.xxx.xxx.xxx
# DNS2=xxx.xxx.xxx.xxx
# DOMAIN=lab.foo.com bar.foo.com
If I have to specify a DNS which IP should I use? the one from LAN Adapter Wireless Network IP (output of ipconfig in MSDOS on Windows 7 on which VMware in which OEL6 is installed) or VMNet1/VMNet8 IP?
Please advise.
Thanks n regards,
Samiullah

Similar Messages

  • Home Hub Error Log

    Does anyone know what the codes stand for?
     I have been having problems, here is an example. Any ideas??
    Feb 3 08:57:05 2011
    ( 4955.810000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 3 08:37:38 2011
    ( 3789.080000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 3 08:37:38 2011
    ( 3789.080000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 3 08:37:38 2011
    ( 3789.080000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 3 08:37:38 2011
    ( 3789.080000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 3 08:22:38 2011
    ( 2888.880000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 3 08:22:38 2011
    ( 2888.880000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 3 08:22:38 2011
    ( 2888.880000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 3 08:22:38 2011
    ( 2888.880000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 3 08:22:08 2011
    ERR 2011-02-03T08:22:08Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 3 08:22:06 2011
    ( 2857.000000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 3 08:22:06 2011
    ( 2857.000000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 3 08:22:06 2011
    ( 2857.000000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 3 08:22:06 2011
    ( 2857.000000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 3 07:36:05 2011
    ( 96.000000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Feb 3 07:35:28 2011
    ( 78.370000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 3 07:35:13 2011
    ERR 2003-01-01T00:00:45Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 3 07:34:53 2011
    ( 43.330000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 3 07:34:53 2011
    ( 43.330000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 3 07:34:53 2011
    ( 43.330000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 3 07:34:53 2011
    ( 43.330000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 3 07:34:36 2011
    ( 26.430000) DVA started
    Feb 3 07:34:35 2011
    ( 25.300000) sys_if_stats_reset failed for atm0

    You're on a long line and your connection looks to keep dropping? Your profile is low, but with 3 -5 days uninterrupted connection that should rise to 1000kbps (1meg).  First of all we need to solve your dropping connection, your output power also looks worryingly low.
    Can I ask what type of master socket do you have?
    Regards Edd
    Check your Line
    BT Speedtester

  • Once again World of Warcraft crazy latency..10k+

    Hey guys,
    Having some problems again with my bb speed etc today..
    Connections been dropping all day as its raining (might have nothing to do with it but you never know)
    and now doing any speed tests shows my speed a 0.33mbs
    Anyway im getting huge latency in everything and you tube vids not loading etc got some info off my hub if it helps
    Apr 23 18:18:20 2012
    ( 642.810000) Admin login successful by 192.168.1.73 on HTTP
    Apr 23 18:09:15 2012
    ( 97.860000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Apr 23 18:08:25 2012
    ( 70.770000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Apr 23 18:08:22 2012
    ( 67.550000) HTTP server returned error 404
    Apr 23 18:08:22 2012
    ERR 2003-01-01T00:00:45Z cwmp: mt_cwmp: session error: Could not resolve host
    Apr 23 18:08:06 2012
    ( 51.150000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Apr 23 18:08:06 2012
    ( 51.150000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Apr 23 18:08:06 2012
    ( 51.150000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Apr 23 18:08:06 2012
    ( 51.150000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Apr 23 18:08:06 2012
    ( 51.090000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Apr 23 18:08:06 2012
    ( 51.090000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Apr 23 18:08:06 2012
    ( 51.090000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Apr 23 18:08:06 2012
    ( 51.090000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Apr 23 18:07:45 2012
    ( 30.570000) DVA started
    Apr 23 18:07:44 2012
    ( 29.150000) sys_if_stats_reset failed for atm0
    1. Product name
    BT Home Hub
    2. Serial number
    edited
    3. Firmware version
    Software version 4.7.5.1.83.3.31.1.1 (Type B) Last updated 24/01/12
    4. Board version
    2.0B
    5. ADSL uptime
    0 days, 00:11:33
    6. Bandwidth
    448 / 7616
    7. Data sent / rec’d
    2.3 / 9.7
    8. Broadband username
    edited
    9. Broadband Talk
    Service not activated
    10. BT FON
    Yes
    11. Wireless network name (SSID)
    oOo
    12. Wireless connections
    Enabled
    13. Wireless security
    WPA and WPA2
    14. Wireless Channel
    Automatic / 11
    15. Firewall
    Disabled
    16. MAC Address
    98:8B:5D:8E:54:A8
    17. VPI/VCI
    0 / 38
    18. Line profile
    Interleaved
    19. Software variant
    20. Boot loader
    ADSL line status
    Connection Information
    Line state
    Connected
    Connection time
    0 days, 00:13:41
    Downstream
    7,616 Kbps
    Upstream
    448 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.1 Annex A
    Latency type
    Interleaved
    Noise margin (Down/Up)
    7.5 dB / 23.0 dB
    Line attenuation (Down/Up)
    26.7 dB / 15.0 dB
    Output power (Down/Up)
    12.2 dBm / 1.6 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    49 / 0
    CRC Errors (Down/Up)
    3 / 5
    HEC Errors (Down/Up)
    6 / 0
    Error Seconds (Local/Remote)
    3 / 1
    This is from speedtest.net, Always get between 5-6.5mbps but at the moment not even .5mbps
    [URL=http://www.speedtest.net][IMG]http://www.speedtest​.net/result/1911333025.png[/IMG][/URL]
    http://www.speedtest.net/result/1911333025.png
    Martin

    Heya mate, thanks for the reply.
    I looked at the sites you mentioned and honestly wish i knew what i was looking at but i have no clue
    From what i looked at it seems nothing is wrong in my area and on one of the pages it shows no faults anywhere so..
    i got this on one page though
    VP capacity at this exchange is currently showing as Green.
    Click here for further details
    BT have advised that no current planned date for WBC on 21CN exists
    You can view recent Service Outages for this exchange here  (followed this link and will post below)
    BT has published DSL Max upgrade information for this exchange
    Click here for further details
    This page shows more details on a particular BT Service Outage.
    : MILTON KEYNES NODE 02177 : PARTIAL LOSS OF SERVICE
    Update Number1
    Detected21/04/2012 15:52
    Started21/04/2012 15:49
    Anticipated Clear Time:21/04/2012 17:49
    Area Codes01162, 01173, 01179, 01205, 01223, 01225, 01234, 01284, 01295, 01297, 01300, 01327, 01344, 01353, 01354, 01366, 01379, 01380, 01406, 01455, 01462, 01485, 01487, 01525, 01529, 01536, 01564, 01582, 01604, 01608, 01635, 01636, 01733, 01763, 01767, 01775, 01778, 01780, 01793, 01794, 01803, 01832, 01865, 01899, 01908, 01933, 01954, 01983, 0208505, 0208506
      Update Number2 Detected21/04/2012 15:52 Started21/04/2012 15:49 Anticipated Clear Time:21/04/2012 19:00 Area Codes01162, 01173, 01179, 01205, 01223, 01225, 01234, 01284, 01295, 01297, 01300, 01327, 01344, 01353, 01354, 01366, 01379, 01380, 01406, 01455, 01462, 01485, 01487, 01525, 01529, 01536, 01564, 01582, 01604, 01608, 01635, 01636, 01733, 01763, 01767, 01775, 01778, 01780, 01793, 01794, 01803, 01832, 01865, 01899, 01908, 01933, 01954, 01983, 0208505, 0208506
      Update NumberFINAL Detected21/04/2012 15:52 Started21/04/2012 15:49 Actual Clear Time:21/04/2012 17:17 Area Codes01162, 01173, 01179, 01205, 01223, 01225, 01234, 01284, 01295, 01297, 01300, 01327, 01344, 01353, 01354, 01366, 01379, 01380, 01406, 01455, 01462, 01485, 01487, 01525, 01529, 01536, 01564, 01582, 01604, 01608, 01635, 01636, 01733, 01763, 01767, 01775, 01778, 01780, 01793, 01794, 01803, 01832, 01865, 01899, 01908, 01933, 01954, 01983, 0208505, 0208506
    Now my area code is covered in this but i had no problems at all until this morning so im not sure if this is the same problem? as in i was playing last night till 1am (woo gotta love week off work) and had 0 latency issues
    Mart

  • Has my BTHHv2.0 typeB gone wrong?

    Event log (results saved to scrapbook)
    This page summarises all the events that have been recorded on your Home Hub since it was last restarted.You can filter the events to show items related to a specific category.
    Feb 2 10:23:12 2010( 24.890000) sys_if_stats_reset failed for atm0
    Feb 2 10:23:13 2010( 26.090000) DVA started
    Feb 2 10:23:34 2010ERR 2003-01-01T00:00:29Z ****: mt_cwmp: session error: Could not resolve host
    Feb 2 10:23:46 2010( 59.330000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 2 10:21:09 2010( 69.090000) WGET: Error connecting to host https://pbthdm.bt.motive.com/****Web/CPEMgt (*)
    Feb 2 10:27:51 2010( 470.590000) WGET: Error connecting to host http://192.168.1.**:****/upnp/eventing/********** (*)
    Feb 2 10:27:51 2010 as above
    Feb 2 10:31:19 2010
    Feb 2 10:31:19 2010
    Feb 2 15:22:08 2010
    Feb 2 15:22:08 2010
    Feb 3 07:53:48 2010
    Feb 3 07:53:48 2010
    Feb 3 17:09:23 2010ERR 2010-02-03T17:09:23Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 3 17:09:55 2010(110900.780000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 3 17:12:26 2010(111052.500000) WGET: Error connecting to host http://192.168.1.**:****/upnp/eventing/********** (192.168.1.**:****)
    Feb 3 17:15:35 2010 as above
    Feb 4 08:44:45 2010
    Feb 4 08:44:45 2010
    Feb 4 10:02:42 2010
    Feb 4 10:02:42 2010
    Feb 5 08:57:17 2010
    Feb 5 08:57:17 2010
    Feb 6 10:28:44 2010(345843.750000) Bad password for user **************** on pbthdm.bt.motive.com
    Feb 6 20:48:42 2010(382948.680000) WGET: Error connecting to host http://192.168.1.**:****/upnp/eventing/********** (192.168.1.**:****)
    Feb 6 20:48:42 2010 as above
    Feb 7 11:01:45 2010
    Feb 7 11:01:45 2010
    Feb 7 17:32:13 2010
    Feb 7 17:32:13 2010
    Feb 7 21:50:11 2010
    Feb 7 21:50:11 2010
    Feb 7 21:50:56 2010(472986.080000) sock_socket: failed bind() for ip 0.0.0.0 port 5060: Address already in use
    Having just checked the event log again all the above events have vanished!!!
    I have NOT restarted my Hub and it appears that it has NOT remote restarted (connection times below)!!
    Internet connection configuration
    Connection Information
    Connection time
    18 days, 06:10:30
    ADSL line status
    Connection Information
    Line state
    Connected
    Connection time
    19 days, 12:58:13
    Now it starts under ALL events
    This page summarises all the events that have been recorded on your Home Hub since it was last restarted.You can filter the events to show items related to a specific category.
    Feb 10 09:02:48 2010(685919.920000) WGET: Error connecting to host http://192.168.1.**:****/upnp/eventing/********** (192.168.1.**:****)
    Feb 10 09:02:48 2010 as above
    Feb 10 10:25:45 2010
    Feb 10 10:25:45 2010
    Feb 10 11:15:22 2010
    Feb 10 11:15:22 2010
    Feb 10 12:35:16 2010
    Feb 10 12:35:16 2010
    Feb 10 12:37:08 2010
    Feb 10 12:37:08 2010
    Feb 11 00:23:00 2010
    Feb 11 00:23:00 2010
    Feb 11 08:25:14 2010
    Feb 11 08:25:14 2010
    Feb 11 14:03:10 2010
    Feb 11 14:03:10 2010
    Feb 11 21:11:53 2010
    Feb 11 21:11:53 2010
    Feb 12 11:29:07 2010
    Feb 12 11:29:08 2010
    Feb 13 11:57:30 2010
    Feb 13 11:57:30 2010
    Feb 13 17:30:39 2010
    Feb 13 17:30:39 2010
    Feb 13 20:54:41 2010
    Feb 13 20:54:41 2010
    Feb 14 10:59:02 2010
    Feb 14 10:59:02 2010
    Feb 14 13:21:55 2010
    Feb 14 13:21:55 2010
    Feb 14 23:57:42 2010
    Feb 14 23:57:43 2010
    Feb 15 09:59:31 2010
    Feb 15 21:14:37 2010
    Feb 15 21:14:38 2010
    Feb 15 21:17:40 2010
    Feb 15 21:17:40 2010
    Feb 15 22:39:03 2010
    Feb 15 22:39:04 2010
    Feb 16 10:08:25 2010
    Feb 16 10:08:25 2010
    Feb 16 18:02:42 2010
    Feb 16 18:02:42 2010
    Feb 17 09:59:38 2010
    Feb 17 09:59:39 2010
    Feb 18 09:30:26 2010
    Feb 18 09:30:26 2010
    Feb 18 10:07:11 2010
    Feb 18 10:07:11 2010
    Feb 19 10:27:08 2010
    Feb 19 10:27:09 2010
    Feb 19 10:29:44 2010
    Feb 19 10:29:44 2010
    Feb 19 18:20:30 2010
    Feb 19 18:20:30 2010
    Feb 20 17:29:28 2010
    Feb 20 17:29:28 2010
    Feb 21 12:56:12 2010
    Feb 21 12:56:12 2010
    Feb 21 21:12:17 2010
    Feb 21 21:12:17 2010
    Having just checked 192.168.1.** I get the following information
    192.168.1.** - Whois Information
    OrgName: Internet Assigned Numbers Authority
    OrgID: IANA
    Address: 4676 Admiralty Way, Suite 330
    City: Marina del Rey
    StateProv: CA
    PostalCode: 90292-6695
    Country: US
    NetRange: 192.168.0.0 - 192.168.255.255
    CIDR: 192.168.0.0/16
    NetName: IANA-CBLK1
    NetHandle: NET-192-168-0-0-1
    Parent: NET-192-0-0-0-0
    NetType: IANA Special Use
    NameServer: BLACKHOLE-1.IANA.ORG
    NameServer: BLACKHOLE-2.IANA.ORG
    Comment: This block is reserved for special purposes.
    Comment: Please see RFC 1918 for additional information.
    Comment: http://www.arin.net/reference/rfc/rfc1918.txt
    RegDate: 1994-03-15
    Updated: 2007-11-27
    OrgAbuseHandle: IANA-IP-ARIN
    OrgAbuseName: Internet Corporation for Assigned Names and Number
    OrgAbusePhone: +1-310-301-5820
    OrgAbuseEmail: [email protected]
    OrgTechHandle: IANA-IP-ARIN
    OrgTechName: Internet Corporation for Assigned Names and Number
    OrgTechPhone: +1-310-301-5820
    OrgTechEmail: [email protected]
    # ARIN WHOIS database, last updated 2010-02-14 20:00
    # Enter ? for additional hints on searching ARIN's WHOIS database.
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at https://www.arin.net/whois_tou.html
    Therefore how can the connection times be different if all equipment has not been touched or unplugged, why is the recent event log not showing all events since Feb 2 2010 and should I be worried as to where my hub is trying to contact (BLACKHOLE)??
    (pbthdm.bt.motive.com) was discussed on another thread.
    -+-No longer a forum member-+-

    The 15 second press did something.
    Good or bad not sure yet!!
    Feb 22 21:08:00 2010
    ( 352.310000) Admin login successful by 192.168.1.64 on HTTP
    Feb 22 21:04:17 2010
    INF 2010-02-22T21:04:17Z cwmp: cwmp_session: session completed successfully
    Feb 22 21:04:17 2010
    INF 2010-02-22T21:04:17Z cwmp: cwmp_session: got empty envelope
    Feb 22 21:04:17 2010
    INF 2010-02-22T21:04:17Z cwmp: cwmp_session: got envelope, len=0
    Feb 22 21:04:17 2010
    INF 2010-02-22T21:04:17Z cwmp: cwmp_session: sending empty envelope to ACS
    Feb 22 21:04:17 2010
    INF 2010-02-22T21:04:17Z cwmp: cwmp_session: got empty envelope
    Feb 22 21:04:17 2010
    INF 2010-02-22T21:04:17Z cwmp: cwmp_session: got envelope, len=0
    Feb 22 21:04:14 2010
    INF 2010-02-22T21:04:14Z cwmp: cwmp_session: SetParameterValues is completed
    Feb 22 21:04:14 2010
    INF 2010-02-22T21:04:14Z cwmp: cwmp_session: sending envelope to ACS
    Feb 22 21:04:14 2010
    INF 2010-02-22T21:04:14Z cwmp: cwmp_param: set InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.Enable, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.Line.1.Enable
    Feb 22 21:04:14 2010
    INF 2010-02-22T21:04:14Z cwmp: cwmp_session: SetParameterValues
    Feb 22 21:04:14 2010
    INF 2010-02-22T21:04:14Z cwmp: cwmp_session: got envelope, len=0
    Feb 22 21:04:14 2010
    INF 2010-02-22T21:04:14Z cwmp: cwmp_session: got envelope, len=1157
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_session: SetParameterValues is completed
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_session: sending envelope to ACS
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_param: set InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.OutboundProxy, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.Line.1.SIP.AuthUserName, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.UserAgentTransport, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.UserAgentPort, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.RegistrarServer, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.Line.1.SIP.AuthPassword, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.RegistrarServerPort, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.ProxyServer, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.ProxyServerPort, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.SIP.OutboundProxyPort, InternetGatewayDevice.Services.VoiceService.1.Voic​eProfile.1.Line.1.CallingFeatures.CallerIDName
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_session: SetParameterValues
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_session: got envelope, len=0
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_session: got envelope, len=358
    Feb 22 21:04:11 2010
    INF 2010-02-22T21:04:11Z cwmp: cwmp_session: got envelope, len=1600
    Feb 22 21:04:10 2010
    INF 2010-02-22T21:04:10Z cwmp: cwmp_session: AddObject is completed
    Feb 22 21:04:10 2010
    INF 2010-02-22T21:04:10Z cwmp: cwmp_session: sending envelope to ACS
    Feb 22 21:04:10 2010
    INF 2010-02-22T21:04:10Z cwmp: cwmp_session: AddObject
    Feb 22 21:02:49 2010
    ( 60.390000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 22 21:02:41 2010
    ERR 2003-01-01T00:00:34Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 22 21:02:15 2010
    ( 25.740000) DVA started
    Feb 22 21:02:13 2010
    ( 24.540000) sys_if_stats_reset failed for atm0
    -+-No longer a forum member-+-

  • 1.2 mps broadband

    For 8 day,s now i have somewhere between 1.2 and zero mps broadband 4 phonr calls 2 emails and nothing has been done other than one returned phone call which i missed when i was attending my father in laws funeral, a funeral in whish the wrong speech was read out because i could not contact the pwrson making it with a revised version as my emails wont load  because they time out like every other page .
    i fully intend to go to the press and refuse to pay my bill you should be ashamed of yourselves i informed you from the first contact that i was organising a funeral, i guess people in Mombai do not havre the same respect as people in the UK have , its obvious BT does not either.

    is any of this the information i am looking for ?
    Time and date
    Message
    Feb 11 21:13:21 2015
    (15083.200000) Admin login successful by 192.168.1.76 on HTTP
    Feb 11 17:35:41 2015
    ( 2022.590000) Socket error
    Feb 11 17:13:52 2015
    ( 714.230000) sock_socket: failed bind() for ip 0.0.0.0 port 5062: Address already in use
    Feb 11 17:03:21 2015
    ( 82.960000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Feb 11 17:02:42 2015
    ( 65.620000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 11 17:02:40 2015
    ERR 2003-01-01T00:00:42Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 11 17:02:23 2015
    ( 46.590000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 11 17:02:23 2015
    ( 46.590000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 11 17:02:23 2015
    ( 46.590000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 11 17:02:23 2015
    ( 46.590000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 11 17:02:23 2015
    ( 46.490000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 11 17:02:23 2015
    ( 46.490000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 11 17:02:23 2015
    ( 46.490000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 11 17:02:23 2015
    ( 46.490000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 11 17:02:06 2015
    ( 29.940000) DVA started
    Feb 11 17:02:05 2015
    ( 28.670000) sys_if_stats_reset failed for atm0 
    FAQ
    1. Best Effort Test: -provides background information.
    Download  Speed
    1 Mbps
    0 Mbps
    7.15 Mbps
    Max Achievable Speed
     Download speedachieved during the test was - 1 Mbps
     For your connection, the acceptable range of speeds is 0.6 Mbps-7.15 Mbps.
     Additional Information:
     Your DSL Connection Rate :7.07 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 6 Mbps
    If you wish to discuss these results please contact your Broadband Service Provider.If you are experiencing problems with specific applications, servers or websites please contact your Broadband Service Provider for assistance.
    Your test has completed please close this window to exit the performance tester.
    Please visit the FAQ if you are unable to understand the test results.

  • Sporadic random disconnects this week, very bad to...

    I've never had any problems with BT Home 2.0 until this week, I have moved nothing about in my room nor adjusted any settings on the hub and my PC. I have changed the filter and still the same problems occur. I've noticed a lot CRC /HEC errors on the up stream... I live in Bristol if that might help to solve the problem. Maybe something next door could be affecting the line or a BT engineer has messed around with something on the exchange? (I am using a wired connection BTW). Any help and suggestions appreciated, thanks, Rob.
    ADSL line status
    Connection information
    Line state
    Connected
    Connection time
    0 days, 0:10:20
    Downstream
    9,727 Kbps
    Upstream
    636 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.5
    Latency type
    Interleaved
    Noise margin (Down/Up)
    7.5 dB / 8.5 dB
    Line attenuation (Down/Up)
    33.5 dB / 18.4 dB
    Output power (Down/Up)
    21.0 dBm / 12.4 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    0 / 208
    CRC Errors (Down/Up)
    44 / 2147480000
    HEC Errors (Down/Up)
    nil / 566812
    Error Seconds (Local)
    39
    TCP/IP settings
    Broadband network IP address
    81.151.168.20
    Default gateway
    217.32.141.33
    Primary DNS
    194.74.65.68
    Secondary DNS
    194.72.0.114
    C:\Users\Robin>tracert 217.32.141.33
    Tracing route to 217.32.141.33 over a maximum of 30 hops
      1    94 ms    98 ms    99 ms  BThomehub.home [192.168.1.254]
      2    16 ms    16 ms    16 ms  217.32.141.33
      3    18 ms    18 ms    33 ms  217.32.141.78
      4    16 ms    16 ms    15 ms  217.32.141.33
    Trace complete.

    Sorry I can't offer any magic suggestions.   I had been getting regular disconnects for some months and even though I was keeping the router continuoulsy powered to avoid loss of line synchronisation it still was occurring.   See my comments in the thread "Re: Disconnects on Accessing HH and Random Disconnects at Night" for 10 Feb. 
    The Forum Moderators were very helpful and responded to my queries and arranged four visits from OpenReach to try and sort out the problem.    Eventually they decided that there was a fault in the exchange boards and made some change.  Subsequently I kept the router powered up until the 13 May to make sure there was no synchronisation interrupts.   The line eventually stabilised at 14,336 kbps.   It has remained at that even with my logical disconnects at night from the HH Home Page.
    I found from a search back in Jan as reported in the thread "Re: HH Type B Energy Consumption & Switching Off the Router" , that the Type A software version was 8.1.H.J.  I don't know if it has been upgraded since.   I have found for my Type B that when received it back in Oct 2010 the ver was 4.7.5.1.83.3.5. and it is now ....83.3.18.   -  when it was changed/upgraded I don't know.
    As I say, although I still get random disconnects, it doesn't seem to affect my line rate.   Not sure if it is noise on the line (i have made a quiet line check and that is OK) as the Noise Margin is ca 7.6-9.1dB.   I get disconnects sometimes when I try to look at the ADSL Settings, etc., having typed in the password for access.  I have just looked at my Events Log and there have been a number of disconnects today since the router was logically connected at 14:04 this afternoon; 5 in total I think!   And the rate is still shown as 14,336 kbps.
    Jun 3 21:29:30 2011    (26713.110000) Admin login successful by 192.168.1.64 on HTTP
    Jun 3 18:26:16 2011    (15719.410000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jun 3 18:25:47 2011    ERR 2011-06-03T17:25:47Z cwmp: mt_cwmp: session error: Could not resolve host
    Jun 3 18:25:46 2011    (15688.810000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jun 3 18:25:46 2011    (15688.740000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jun 3 18:06:05 2011    (14507.480000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jun 3 18:05:35 2011    ERR 2011-06-03T17:05:35Z cwmp: mt_cwmp: session error: Could not resolve host
    Jun 3 18:05:34 2011    (14476.950000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jun 3 18:05:34 2011    (14476.890000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jun 3 15:03:16 2011    ( 3538.970000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jun 3 15:02:48 2011    ERR 2011-06-03T14:02:48Z cwmp: mt_cwmp: session error: Could not resolve host
    Jun 3 15:02:46 2011    ( 3508.470000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jun 3 14:34:10 2011    ( 1793.130000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jun 3 14:33:41 2011    ERR 2011-06-03T13:33:41Z cwmp: mt_cwmp: session error: Could not resolve host
    Jun 3 14:33:40 2011    ( 1763.120000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jun 3 14:33:40 2011    ( 1763.070000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jun 3 14:06:16 2011    ( 119.040000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Jun 3 14:05:44 2011    ( 109.480000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jun 3 14:05:39 2011    ( 104.560000) Admin login successful by 192.168.1.64 on HTTP
    Jun 3 14:04:43 2011    ERR 2003-01-01T00:00:27Z cwmp: mt_cwmp: session error: Could not resolve host
    Jun 3 14:04:39 2011    ( 44.450000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jun 3 14:04:39 2011    ( 44.380000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jun 3 14:04:23 2011    ( 28.920000) DVA started
    Jun 3 14:04:23 2011    ( 28.170000) sys_if_stats_reset failed for atm0
    Having said that your rate is quite reasonable and unless you are playing games or watching videos perhaps the interrupts will not be serious.   We only use it for email, family history, ebay and browsing so it is not really noticeable.
    Rodney Fry

  • Broadband really slow annoyingly slow since friday

    Hi
    My internet is really slow and lagging, i cant see any problems in my area (northamptonshire) so thought doing a test on my line to check speed might help, only it wont work!
    Im a uni student and i cant access my course
    Hub settings are -
    ADSL line status
    Connection Information
    Line state
    Connected
    Connection time
    0 days, 05:48:54
    Downstream
    3,835 Kbps
    Upstream
    979 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.5 Annex A
    Latency type
    Fast
    Noise margin (Down/Up)
    7.1 dB / 5.7 dB
    Line attenuation (Down/Up)
    53.7 dB / 32.2 dB
    Output power (Down/Up)
    6.1 dBm / 1.4 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    0 / 0
    CRC Errors (Down/Up)
    11199 / 0
    HEC Errors (Down/Up)
    3280917 / 0
    Error Seconds (Local/Remote)
    20943 / 0

    Time and date
    Message
    Feb 5 20:45:01 2012
    (23176.350000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:36:42 2012
    (22677.820000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:36:27 2012
    (22662.350000) Admin login successful by 192.168.1.77 on HTTP
    Feb 5 20:19:39 2012
    (21655.110000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:19:34 2012
    (21649.870000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:19:32 2012
    (21647.530000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:19:30 2012
    (21646.150000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:12:23 2012
    (21219.120000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 20:08:04 2012
    (20960.240000) Admin login successful by 192.168.1.77 on HTTP
    Feb 5 19:57:29 2012
    (20325.260000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 19:57:21 2012
    (20316.550000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 19:56:22 2012
    (20257.360000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 19:55:08 2012
    (20183.400000) HTTP server returned error 404
    Feb 5 19:01:23 2012
    (16959.200000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 18:56:52 2012
    (16687.450000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 18:56:19 2012
    (16654.330000) Admin login successful by 192.168.1.77 on HTTP
    Feb 5 18:33:07 2012
    (15262.390000) sock_socket: failed bind() for ip 0.0.0.0 port 61376: Address already in use
    Feb 5 18:28:51 2012
    (15006.670000) HTTP server returned error 404
    Feb 5 16:33:19 2012
    ( 8075.140000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 16:33:13 2012
    ( 8068.690000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 14:21:13 2012
    ( 149.300000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 14:21:11 2012
    ( 146.850000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 14:20:38 2012
    ( 114.120000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Feb 5 14:19:56 2012
    ( 94.140000) danube_dsl_ioctl:88: Failed ioctl 290 errno 61
    Feb 5 14:19:45 2012
    ( 83.380000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 5 14:19:24 2012
    ERR 2003-01-01T00:00:40Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 5 14:19:23 2012
    ( 60.930000) HTTP server returned error 404
    Feb 5 14:19:10 2012
    ( 48.180000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 5 14:19:10 2012
    ( 48.180000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 5 14:19:10 2012
    ( 48.180000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 5 14:19:10 2012
    ( 48.180000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 5 14:19:10 2012
    ( 48.100000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 5 14:19:10 2012
    ( 48.100000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Feb 5 14:19:10 2012
    ( 48.100000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Feb 5 14:19:10 2012
    ( 48.100000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 5 14:18:52 2012
    ( 30.110000) DVA started
    Feb 5 14:18:51 2012
    ( 28.680000) sys_if_stats_reset failed for atm0

  • Please I need help - 6mths of talking to BT and no...

    I have been having problems with my broadband since September 2010. The ironic things is, that when it works it is fantastic 19meg downloads. We just keep losing wirless and random points of the day and night. The wired connections also slow down. The wirless devices can see the router and are connected, but not get beyond. They don't all disconnect at the same time either.
    I have lost counts of how many times I have rung the call centre. I have changed, filters, cables on numerous occassions.
    After one engineer came he called India as he suspected they had been tampering, after this call everyting started working fantastically, alas this was only for 48 hours. Then all the original problems reurned.
    We have now has 4 engineers out (apparently they are all different engineers....). Still have the same problems. There are pages and pages or error logs on the router (no-one at BT understands these apparently!). eg
    Jan 17 15:11:00 2011
    (1039475.920000) Admin login successful by 192.168.1.65 on HTTP
    Jan 17 15:10:23 2011
    (1039439.410000) WGET: Error connecting to host http://192.168.1.65:2869/upnp/eventing/xzvuaxetkl (192.168.1.65:2869)
    Jan 17 15:10:23 2011
    (1039439.360000) Socket error
    Jan 17 15:09:45 2011
    INF 2011-01-17T15:09:45Z cwmp: cwmp_session: session completed successfully
    Jan 17 15:09:45 2011
    INF 2011-01-17T15:09:45Z cwmp: cwmp_session: got empty envelope
    Jan 17 15:09:23 2011
    (1039379.770000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jan 17 15:08:52 2011
    (1039348.030000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 15:08:52 2011
    (1039348.030000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 15:08:52 2011
    (1039348.030000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 15:08:52 2011
    (1039348.030000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 15:08:22 2011
    ERR 2011-01-17T15:08:22Z cwmp: mt_cwmp: session error: Could not resolve host
    Jan 17 15:08:17 2011
    (1039312.980000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 15:08:17 2011
    (1039312.980000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 15:08:17 2011
    (1039312.980000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 15:08:17 2011
    (1039312.980000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 14:02:17 2011
    (1035433.290000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jan 17 14:01:05 2011
    (1035361.780000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 14:01:05 2011
    (1035361.780000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 14:01:05 2011
    (1035361.780000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 14:01:05 2011
    (1035361.780000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 13:46:05 2011
    (1034461.550000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 13:46:05 2011
    (1034461.550000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 13:46:05 2011
    (1034461.550000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 13:46:05 2011
    (1034461.550000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 13:45:35 2011
    ERR 2011-01-17T13:45:35Z cwmp: mt_cwmp: session error: Could not resolve host
    Jan 17 13:45:33 2011
    (1034429.310000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 13:45:33 2011
    (1034429.300000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 13:45:33 2011
    (1034429.300000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 13:45:33 2011
    (1034429.300000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 13:35:41 2011
    (1033837.890000) Socket error
    Jan 17 13:35:41 2011
    (1033837.890000) Socket error
    Jan 17 13:30:14 2011
    (1033510.660000) Socket error
    Jan 17 13:30:05 2011
    (1033501.630000) WGET: Error connecting to host http://192.168.1.65:2869/upnp/eventing/pqwdalyvqc (192.168.1.65:2869)
    Jan 17 13:30:05 2011
    (1033501.620000) WGET: Error connecting to host http://192.168.1.65:2869/upnp/eventing/rkcvdjtawu (192.168.1.65:2869)
    Jan 17 13:30:05 2011
    (1033501.620000) WGET: Error connecting to host http://192.168.1.65:2869/upnp/eventing/drnogcnscy (192.168.1.65:2869)
    Jan 17 13:30:05 2011
    (1033501.620000) WGET: Error connecting to host http://192.168.1.65:2869/upnp/eventing/fnpstghbwb (192.168.1.65:2869)
    Jan 17 13:29:54 2011
    (1033490.480000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Jan 17 13:29:20 2011
    (1033456.550000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 13:29:20 2011
    (1033456.550000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 13:29:20 2011
    (1033456.550000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 13:29:20 2011
    (1033456.550000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 13:28:50 2011
    ERR 2011-01-17T13:28:50Z cwmp: mt_cwmp: session error: Could not resolve host
    Jan 17 13:28:48 2011
    (1033424.230000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Jan 17 13:28:48 2011
    (1033424.230000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Jan 17 13:28:48 2011
    (1033424.230000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Jan 17 13:28:48 2011
    (1033424.230000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Jan 17 13:08:10 2011
    (1032186.110000) WGET: Error connecting to host http://192.168.1.65:2869/upnp/eventing/chxealbrvi (192.168.1.65:2869)

    My stats. can't run a spedd test and it knocks the internet out.
    Line state
    Connected
    Connection time
    0 days, 00:01:31
    Downstream
    19,715 Kbps
    Upstream
    1,212 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.5 Annex A
    Latency type
    Interleaved
    Noise margin (Down/Up)
    7.6 dB / 5.9 dB
    Line attenuation (Down/Up)
    10.6 dB / 3.5 dB
    Output power (Down/Up)
    30.0 dBm / 1.8 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    0 / 0
    CRC Errors (Down/Up)
    0 / 32
    HEC Errors (Down/Up)
    7 / 0
    Error Seconds (Local/Remote)
    0 / 0

  • Best way to clone a installation

    Hi
    I installed and configured arch on an older machine and now would like to clone the installation (mostly because all the mail settings, etc) to a different machine... my plan was to install the basic installtion from a live cd and then copy all files from the old / .
    I know there are certain files than are machine specifiic eg. /etc/fstab, the extlinux loader file etc...
    so I tried to copy everything but these machine specific files, but that ruined the installation so I guess I am doing something wrong. Is there an easier way to clone the setup or did I just miss a specific file?
    Does anyone have experience in this issue?
    regards,
    keen
    Last edited by keen90 (2011-09-03 23:38:26)

    The user issue is fine now.
    I used an external hard drive to copy my old installations data and did not use
    cp -ar
    so the permissions were missing. I fixed that.
    I'll post my /var/log messages in a couple of minutes.
    One more thing. I am a bit worried about the system I tried a pacman update und had these messages:
    :: Synchronizing package databases...
    core is up to date
    extra is up to date
    community is up to date
    error: duplicated database entry 'iproute2'
    error: duplicated database entry 'iana-etc'
    error: duplicated database entry 'usbutils'
    error: duplicated database entry 'syslog-ng'
    error: duplicated database entry 'binutils'
    error: duplicated database entry 'file'
    error: duplicated database entry 'device-mapper'
    error: duplicated database entry 'gcc-libs'
    error: duplicated database entry 'mkinitcpio-busybox'
    error: duplicated database entry 'module-init-tools'
    error: duplicated database entry 'readline'
    error: duplicated database entry 'glibc'
    error: duplicated database entry 'cronie'
    error: duplicated database entry 'pcmciautils'
    error: duplicated database entry 'pcre'
    error: duplicated database entry 'psmisc'
    error: duplicated database entry 'syslinux'
    error: duplicated database entry 'coreutils'
    error: duplicated database entry 'libgcrypt'
    error: duplicated database entry 'initscripts'
    error: duplicated database entry 'tzdata'
    error: duplicated database entry 'zlib'
    error: duplicated database entry 'linux-api-headers'
    error: duplicated database entry 'util-linux'
    error: duplicated database entry 'less'
    error: duplicated database entry 'dbus-core'
    error: duplicated database entry 'pacman-mirrorlist'
    error: duplicated database entry 'grep'
    error: duplicated database entry 'grub'
    error: duplicated database entry 'pam'
    error: duplicated database entry 'libcap'
    error: duplicated database entry 'heirloom-mailx'
    error: duplicated database entry 'perl'
    error: duplicated database entry 'logrotate'
    error: duplicated database entry 'mkinitcpio'
    error: duplicated database entry 'wget'
    error: duplicated database entry 'dash'
    error: duplicated database entry 'cryptsetup'
    error: duplicated database entry 'lvm2'
    error: duplicated database entry 'gmp'
    error: duplicated database entry 'db'
    error: duplicated database entry 'libgpg-error'
    error: duplicated database entry 'mdadm'
    error: duplicated database entry 'filesystem'
    error: duplicated database entry 'pacman'
    error: duplicated database entry 'procps'
    error: duplicated database entry 'shadow'
    error: duplicated database entry 'run-parts'
    error: duplicated database entry 'udev'
    error: duplicated database entry 'gawk'
    error: duplicated database entry 'diffutils'
    error: duplicated database entry 'linux-firmware'
    :: Starting full system upgrade...
    resolving dependencies...
    looking for inter-conflicts...
    Remove (1): kernel26-2.6.38.8-1
    Total Removed Size: 52.11 MB
    Targets (35): zlib-1.2.5-4 binutils-2.21.1-2 shadow-4.1.4.3-2 libcap-2.22-1 coreutils-8.12-3 cronie-1.4.8-1 gcc-libs-4.6.1-4 db-5.2.28-1 iana-etc-2.30-2 filesystem-2011.08-1 dbus-core-1.4.14-1 diffutils-3.1-1 file-5.08-1 gawk-4.0.0-1 pcre-8.13-2 grep-2.9-1 grub-0.97-20 heirloom-mailx-12.5-2 imlib2-1.4.5-1 module-init-tools-3.16-1 udev-173-3 iproute2-2.6.39-1 initscripts-2011.07.3-1 linux-firmware-20110822-1 linux-3.0.4-1 less-444-1 libgcrypt-1.5.0-1 linux-api-headers-3.0.1-1 mdadm-3.2.2-3 mkinitcpio-busybox-1.18.5-1 pacman-mirrorlist-20110816-1 psmisc-22.14-1 syslinux-4.04-2 syslog-ng-3.2.4-3 usbutils-004-1
    Total Download Size: 0.00 MB
    Total Installed Size: 165.15 MB
    checking package integrity...
    checking for file conflicts...
    binutils: /usr/lib/libbfd-2.21.1.20110627.so exists in filesystem
    binutils: /usr/lib/libopcodes-2.21.1.20110627.so exists in filesystem
    shadow: /usr/share/licenses/shadow/LICENSE exists in filesystem
    libcap: /lib/libcap.so.2.22 exists in filesystem
    db: /usr/bin/db_tuner exists in filesystem
    db: /usr/lib/libdb-5.2.a exists in filesystem
    db: /usr/lib/libdb-5.2.so exists in filesystem
    db: /usr/lib/libdb_cxx-5.2.a exists in filesystem
    db: /usr/lib/libdb_cxx-5.2.so exists in filesystem
    dbus-core: /usr/lib/libdbus-1.so.3.5.7 exists in filesystem
    dbus-core: /usr/share/doc/dbus/dbus-faq.html exists in filesystem
    dbus-core: /usr/share/doc/dbus/dbus-specification.html exists in filesystem
    dbus-core: /usr/share/doc/dbus/dbus-test-plan.html exists in filesystem
    dbus-core: /usr/share/doc/dbus/dbus-tutorial.html exists in filesystem
    dbus-core: /usr/share/doc/dbus/diagram.png exists in filesystem
    dbus-core: /usr/share/doc/dbus/diagram.svg exists in filesystem
    dbus-core: /usr/share/doc/dbus/system-activation.txt exists in filesystem
    diffutils: /usr/share/info/diffutils.info.gz exists in filesystem
    gawk: /bin/gawk-4.0.0 exists in filesystem
    gawk: /usr/bin/dgawk exists in filesystem
    gawk: /usr/bin/pgawk-4.0.0 exists in filesystem
    gawk: /usr/share/awk/quicksort.awk exists in filesystem
    gawk: /usr/share/awk/walkarray.awk exists in filesystem
    gawk: /usr/share/locale/fi/LC_MESSAGES/gawk.mo exists in filesystem
    module-init-tools: /usr/share/man/man5/depmod.d.5.gz exists in filesystem
    module-init-tools: /usr/share/man/man5/modules.dep.bin.5.gz exists in filesystem
    udev: /lib/libudev.so.0.12.0 exists in filesystem
    udev: /lib/modprobe.d/framebuffer_blacklist.conf exists in filesystem
    udev: /lib/udev/accelerometer exists in filesystem
    udev: /lib/udev/rules.d/61-accelerometer.rules exists in filesystem
    udev: /lib/udev/rules.d/70-udev-acl.rules exists in filesystem
    iproute2: /etc/iproute2/group exists in filesystem
    initscripts: /etc/logrotate.d/bootlog exists in filesystem
    initscripts: /usr/lib/initscripts/arch-tmpfiles exists in filesystem
    initscripts: /usr/lib/tmpfiles.d/arch.conf exists in filesystem
    linux-firmware: /lib/firmware/ar3k/30101coex/PS_ASIC.pst exists in filesystem
    linux-firmware: /lib/firmware/ar3k/30101coex/PS_ASIC_aclHighPri.pst exists in filesystem
    linux-firmware: /lib/firmware/ar3k/30101coex/PS_ASIC_aclLowPri.pst exists in filesystem
    linux-firmware: /lib/firmware/ar3k/30101coex/RamPatch.txt exists in filesystem
    linux-firmware: /lib/firmware/ar3k/30101coex/ar3kbdaddr.pst exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/athwlan.bin exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/bdata.SD31.bin exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/bdata.SD32.bin exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/bdata.WB31.bin exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/data.patch.bin exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/endpointping.bin exists in filesystem
    linux-firmware: /lib/firmware/ath6k/AR6003.1/hw2.1.1/otp.bin exists in filesystem
    linux-firmware: /lib/firmware/bnx2x/bnx2x-e1-7.0.20.0.fw exists in filesystem
    linux-firmware: /lib/firmware/bnx2x/bnx2x-e1-7.0.23.0.fw exists in filesystem
    linux-firmware: /lib/firmware/bnx2x/bnx2x-e1h-7.0.20.0.fw exists in filesystem
    linux-firmware: /lib/firmware/bnx2x/bnx2x-e1h-7.0.23.0.fw exists in filesystem
    linux-firmware: /lib/firmware/bnx2x/bnx2x-e2-7.0.20.0.fw exists in filesystem
    linux-firmware: /lib/firmware/bnx2x/bnx2x-e2-7.0.23.0.fw exists in filesystem
    linux-firmware: /lib/firmware/cis/src/3CCFEM556.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/3CXEM556.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/COMpad2.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/COMpad4.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/DP83903.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/LA-PCM.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/MT5634ZLX.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/NE2K.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/PCMLM28.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/PE-200.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/PE520.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/RS-COM-2P.cis exists in filesystem
    linux-firmware: /lib/firmware/cis/src/tamarack.cis exists in filesystem
    linux-firmware: /lib/firmware/dvb-usb-terratec-h5-drxk.fw exists in filesystem
    linux-firmware: /lib/firmware/ene-ub6250/ms_init.bin exists in filesystem
    linux-firmware: /lib/firmware/ene-ub6250/ms_rdwr.bin exists in filesystem
    linux-firmware: /lib/firmware/ene-ub6250/msp_rdwr.bin exists in filesystem
    linux-firmware: /lib/firmware/ene-ub6250/sd_init1.bin exists in filesystem
    linux-firmware: /lib/firmware/ene-ub6250/sd_init2.bin exists in filesystem
    linux-firmware: /lib/firmware/ene-ub6250/sd_rdwr.bin exists in filesystem
    linux-firmware: /lib/firmware/libertas/cf8381.bin exists in filesystem
    linux-firmware: /lib/firmware/libertas/cf8381_helper.bin exists in filesystem
    linux-firmware: /lib/firmware/libertas/lbtf_sdio.bin exists in filesystem
    linux-firmware: /lib/firmware/libertas/lbtf_usb.bin exists in filesystem
    linux-firmware: /lib/firmware/libertas/usb8388_olpc.bin exists in filesystem
    linux-firmware: /lib/firmware/radeon/SUMO2_me.bin exists in filesystem
    linux-firmware: /lib/firmware/radeon/SUMO2_pfp.bin exists in filesystem
    linux-firmware: /lib/firmware/radeon/SUMO_me.bin exists in filesystem
    linux-firmware: /lib/firmware/radeon/SUMO_pfp.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl127x-fw-3.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl127x-fw-plt-3.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl127x-nvs.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl128x-fw-3.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl128x-fw-plt-3.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl128x-nvs.bin exists in filesystem
    linux-firmware: /lib/firmware/ti-connectivity/wl12xx-nvs.bin exists in filesystem
    linux-firmware: /usr/share/licenses/linux-firmware/LICENCE.OLPC exists in filesystem
    linux-firmware: /usr/share/licenses/linux-firmware/LICENCE.ene_firmware exists in filesystem
    libgcrypt: /lib/libgcrypt.so.11.7.0 exists in filesystem
    libgcrypt: /usr/share/info/gcrypt.info-1.gz exists in filesystem
    linux-api-headers: /usr/include/linux/media.h exists in filesystem
    linux-api-headers: /usr/include/linux/mmc/ioctl.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/ipset/ip_set.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/ipset/ip_set_bitmap.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/ipset/ip_set_hash.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/ipset/ip_set_list.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/xt_AUDIT.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/xt_addrtype.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/xt_devgroup.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/xt_set.h exists in filesystem
    linux-api-headers: /usr/include/linux/netfilter/xt_socket.h exists in filesystem
    linux-api-headers: /usr/include/linux/omap3isp.h exists in filesystem
    linux-api-headers: /usr/include/linux/ptp_clock.h exists in filesystem
    linux-api-headers: /usr/include/linux/usb/functionfs.h exists in filesystem
    linux-api-headers: /usr/include/linux/uvcvideo.h exists in filesystem
    linux-api-headers: /usr/include/linux/v4l2-mediabus.h exists in filesystem
    linux-api-headers: /usr/include/linux/v4l2-subdev.h exists in filesystem
    linux-api-headers: /usr/include/rdma/ib_user_cm.h exists in filesystem
    linux-api-headers: /usr/include/rdma/ib_user_sa.h exists in filesystem
    linux-api-headers: /usr/include/rdma/ib_user_verbs.h exists in filesystem
    linux-api-headers: /usr/include/rdma/rdma_netlink.h exists in filesystem
    linux-api-headers: /usr/include/rdma/rdma_user_cm.h exists in filesystem
    syslog-ng: /lib/systemd/system/syslog-ng.service exists in filesystem
    Errors occurred, no packages were upgraded.
    Last edited by keen90 (2011-09-04 16:49:15)

  • Kernel panic, yaboot, empty /dev

    Hello,
    I'm new to arch and just tried to install it on a G3 iBook. I tried the quickinstall way, but there was this wget error so it didn't work. Then I tried setup which, which was fine. For kernel installing I chrooted to the new install and used pacman. While I was at it I checked config files and so far I think they're ok. Exit the chroot, install yaboot, that was basically it. But the new install's /dev is completely empty (makedevs is not available after chrooting) except for console, null and zero. So I used pacman to install MAKEDEV and created nodes for hda. But even with this it still doesn't boot. I noticed that /dev/hda3 is being generated at boot, still I get this:
    kinit: Cannot open root device hda3(3,3)
    kinit: init not found!
    So I guess everything is fine until the boot process comes to the point of accessing /, where it borks. Does anyone have an idea how to fix this?

    Changed everything to persistent block device naming like mentioned here, with little effect. By now I don't think that the error is connected to error in my configs, I think it connected to this:
    :: Running Hook [udev]
    :: Loading udev.../etc/start_udev: 110: /sbin/udevtrigger: not found
    /etc/start_udev: 110: /sbin/udevsettle: not found
    If I understand this correctly then udev just isn't starting up correctly, right? Both mentioned symlinks are present in /sbin, so what might be the problem here?
    Update: Like mentioned here I reinstalled the packages (look in post #13) and rebuild the image, but still no love. I desperately need help because I'm out of ideas.. the kernel boots, but when it comes to accessing the harddrive, everything goes down the drain.
    Edit: For additional infos, I also posted my problem in this thread. Should I really just kill everything and try to install via quickinst, replacing wget with snarf in the process? How should I even do this?
    Last edited by p2501 (2008-07-28 08:19:33)

  • WTF is wrong

    So I'm trying to skype my girlfriend but I always get disconnected and my internet gets destroyed by it for about 10 minutes. It eventually comes back though. This is unbearable.
    Here's my log if it helps:
    Mar 29 12:03:22 2015
    ( 199.650000) Admin login successful by 192.168.1.90 on HTTP
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: session completed successfully
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: got empty envelope
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: got envelope, len=0
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: InformResponse is completed
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: sending empty envelope to ACS
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: InformResponse
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: got envelope, len=0
    Mar 29 12:02:19 2015
    INF 2015-03-29T12:02:19Z cwmp: cwmp_session: got envelope, len=455
    Mar 29 12:02:16 2015
    INF 2015-03-29T12:02:16Z cwmp: cwmp_session: sending envelope to ACS
    Mar 29 12:02:16 2015
    INF 2015-03-29T12:02:16Z cwmp: session started event code(s): '1 BOOT'
    Mar 29 12:01:45 2015
    INF 2015-03-29T12:01:45Z cwmp: mt_cwmp: session not established, will retry in 30 seconds
    Mar 29 12:01:45 2015
    INF 2015-03-29T12:01:45Z cwmp: cwmp_session: session completed successfully
    Mar 29 12:01:45 2015
    INF 2015-03-29T12:01:45Z cwmp: cwmp_session: got envelope, len=-1
    Mar 29 12:01:45 2015
    ( 103.030000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Mar 29 12:01:22 2015
    ( 102.330000) Detected Asterisk isn't stuck anymore
    Mar 29 12:01:13 2015
    INF 2003-01-01T00:01:11Z cwmp: cwmp_session: sending envelope to ACS
    Mar 29 12:01:13 2015
    INF 2003-01-01T00:01:11Z cwmp: session started event code(s): '1 BOOT'
    Mar 29 12:01:07 2015
    ( 87.480000) Asterisk is stuck
    Mar 29 12:01:03 2015
    ( 82.920000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 29 12:00:33 2015
    ERR 2003-01-01T00:00:31Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 29 12:00:27 2015
    ( 47.330000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 29 12:00:27 2015
    ( 47.330000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Mar 29 12:00:27 2015
    ( 47.330000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Mar 29 12:00:27 2015
    ( 47.330000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 29 12:00:27 2015
    ( 47.290000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 29 12:00:27 2015
    ( 47.290000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Mar 29 12:00:27 2015
    ( 47.280000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Mar 29 12:00:27 2015
    ( 47.280000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 29 12:00:10 2015
    ( 30.260000) DVA started
    Mar 29 12:00:09 2015
    ( 28.990000) sys_if_stats_reset failed for atm0

    what hub are you using
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • Broadband speed has dropped quite considerably

    Hi,
    I usually have a 12-16mb speed with total broadband option 3 package in my area, but it has dropped to below 3mb. I've done a BT speedtest without result as it leaves a message it cannot complete the test.
    I have recently updated my cables after a previous issue, and my cable plugs directly into the test socket.  I am not using an extension
    Here are the ADSL details (downstream seems very low)
    ADSL line status
    Connection Information
    Line state
    Connected
    Connection time
    0 days, 07:34:29
    Downstream
    3,072 Kbps
    Upstream
    440 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.5 Annex A
    Latency type
    Interleaved
    Noise margin (Down/Up)
    16.8 dB / 26.1 dB
    Line attenuation (Down/Up)
    33.5 dB / 16.0 dB
    Output power (Down/Up)
    18.6 dBm / 1.3 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    371 / 0
    CRC Errors (Down/Up)
    0 / 0
    HEC Errors (Down/Up)
    0 / 0
    Error Seconds (Local/Remote)
    0 / 0
    The event details:
    Recorded events Time and date Message
    Oct 27 20:05:06 2013(27162.310000) Admin login successful by 192.168.1.64 on HTTP
    Oct 27 20:04:00 2013(27096.650000) Admin login FAILED by 192.168.1.64 on HTTP
    Oct 27 20:02:58 2013(27034.920000) Admin login FAILED by 192.168.1.64 on HTTP
    Oct 27 19:19:58 2013[24458.520000] klips_error:ipsec_tunnel_start_xmit: ip_send() failed, err=-1
    Oct 27 16:01:06 2013(12522.640000) HTTP server returned error 404
    Oct 27 13:01:54 2013[ 1774.790000] klips_error:ipsec_tunnel_start_xmit: ip_send() failed, err=-1
    Oct 27 12:34:01 2013( 97.560000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Oct 27 12:33:27 2013( 85.640000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Oct 27 12:32:58 2013ERR 2003-01-01T00:00:35Z cwmp: mt_cwmp: session error: Could not resolve host
    Oct 27 12:32:57 2013( 55.500000) HTTP server returned error 404
    Oct 27 12:32:48 2013( 46.450000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Oct 27 12:32:48 2013( 46.450000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Oct 27 12:32:48 2013( 46.450000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Oct 27 12:32:48 2013( 46.450000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Oct 27 12:32:48 2013( 46.370000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Oct 27 12:32:48 2013( 46.370000) danube_dsl_ioctl:88: Failed ioctl 255 errno 22
    Oct 27 12:32:48 2013( 46.370000) danube_dsl_ioctl:88: Failed ioctl 290 errno 22
    Oct 27 12:32:48 2013( 46.370000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Oct 27 12:32:31 2013( 29.770000) DVA started
    Oct 27 12:32:30 2013( 28.360000) sys_if_stats_reset failed for atm0
    Solved!
    Go to Solution.

    Have you been having problems with router dropping connection or manual resets or a combination of both?
    I think you are in a banded profile because of the drop/resets but if you maintain a stable connection 24/7 for 3/5 days the banding should release automatically with noise margin falling and speed increasing. If you get to 3+days connection time and still 3072 then repost your stats and mods will help you get out banding
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Grrrr

    Funny how when i threaten to ask for my MAC code and leave BT my net speed shoots back to where it should be - almost instantly!.
     ANyway now all sudden my hub is constantly rebooting - actualy - it just goes to rboot and does **bleep** all . i have to reset it to reconect. TWICE in 5 minutes!!!
    Mar 22 03:31:10 2011
    ( 130.430000) Admin login successful by 192.168.1.64 on HTTP
    Mar 22 03:30:46 2011
    INF 2011-03-22T03:30:46Z cwmp: cwmp_session: session completed successfully
    Mar 22 03:30:46 2011
    INF 2011-03-22T03:30:46Z cwmp: cwmp_session: got empty envelope
    Mar 22 03:30:46 2011
    INF 2011-03-22T03:30:46Z cwmp: cwmp_session: got envelope, len=0
    Mar 22 03:30:45 2011
    INF 2011-03-22T03:30:45Z cwmp: cwmp_session: InformResponse is completed
    Mar 22 03:30:45 2011
    INF 2011-03-22T03:30:45Z cwmp: cwmp_session: sending empty envelope to ACS
    Mar 22 03:30:45 2011
    INF 2011-03-22T03:30:45Z cwmp: cwmp_session: InformResponse
    Mar 22 03:30:45 2011
    INF 2011-03-22T03:30:45Z cwmp: cwmp_session: got envelope, len=0
    Mar 22 03:30:45 2011
    INF 2011-03-22T03:30:45Z cwmp: cwmp_session: got envelope, len=455
    Mar 22 03:30:43 2011
    INF 2011-03-22T03:30:43Z cwmp: cwmp_session: sending envelope to ACS
    Mar 22 03:30:43 2011
    INF 2011-03-22T03:30:43Z cwmp: session started event code(s): '1 BOOT'
    Mar 22 03:30:13 2011
    INF 2011-03-22T03:30:13Z cwmp: mt_cwmp: session not established, will retry in 30 seconds
    Mar 22 03:30:13 2011
    INF 2011-03-22T03:30:13Z cwmp: cwmp_session: session completed successfully
    Mar 22 03:30:13 2011
    INF 2011-03-22T03:30:13Z cwmp: cwmp_session: got envelope, len=-1
    Mar 22 03:30:13 2011
    ( 72.830000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Mar 22 03:29:47 2011
    INF 2003-01-01T00:00:48Z cwmp: cwmp_session: sending envelope to ACS
    Mar 22 03:29:47 2011
    INF 2003-01-01T00:00:48Z cwmp: session started event code(s): '1 BOOT'
    Mar 22 03:29:41 2011
    ( 60.840000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 22 03:29:40 2011
    ERR 2003-01-01T00:00:41Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 22 03:29:40 2011
    INF 2003-01-01T00:00:41Z cwmp: mt_cwmp: session not established, will retry in 30 seconds
    Mar 22 03:29:40 2011
    INF 2003-01-01T00:00:41Z cwmp: cwmp_session: session completed successfully
    Mar 22 03:29:40 2011
    INF 2003-01-01T00:00:41Z cwmp: cwmp_session: got envelope, len=-1
    Mar 22 03:29:24 2011
    INF 2003-01-01T00:00:25Z cwmp: cwmp_session: sending envelope to ACS
    Mar 22 03:29:24 2011
    INF 2003-01-01T00:00:25Z cwmp: session started event code(s): '1 BOOT'
    Mar 22 03:29:24 2011
    ( 43.080000) danube_dsl_ioctl:73: Failed ioctl 250 errno 22
    Mar 22 03:29:24 2011
    ( 43.080000) danube_dsl_ioctl:73: Failed ioctl 255 errno 22
    Mar 22 03:29:24 2011
    ( 43.080000) danube_dsl_ioctl:73: Failed ioctl 290 errno 22
    Mar 22 03:29:24 2011
    ( 43.080000) danube_dsl_ioctl:73: Failed ioctl 270 errno 22
    Mar 22 03:29:24 2011
    ( 42.940000) danube_dsl_ioctl:73: Failed ioctl 250 errno 22
    Mar 22 03:29:24 2011
    ( 42.940000) danube_dsl_ioctl:73: Failed ioctl 255 errno 22
    Mar 22 03:29:24 2011
    ( 42.940000) danube_dsl_ioctl:73: Failed ioctl 290 errno 22
    Mar 22 03:29:24 2011
    ( 42.940000) danube_dsl_ioctl:73: Failed ioctl 270 errno 22
    Mar 22 03:29:07 2011
    ( 26.390000) DVA started
    Mar 22 03:29:06 2011
    ( 25.060000) sys_if_stats_reset failed for atm0

    Hi m_yeomans
    One disconnect a day should not be causing major problems, if this isn't impacting your SNR figure or killing your download speed it should be ok.
    Can you post up hub stats and a www.speedtester.bt.com for us to have a look please?
    ta
    Craig 
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)”
    td-p/30">Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Low Noise Margin, Regular Drop Outs of Broadband?

    I have noticed recently that my HH2 type B router is showing at various times a disconnect yellow LED.    This was not causing a major problem, but on reflection I think it has been happening since before Christmas.   I decided to check on the HH2 ADSL Connections and Event Log pages and keep copies of the text from 24 Feb.   Although I usually switch the HH off with the computer, I have refrained from doing so for the last week or two in case that was a possible cause.   The Event Log shows short connection times.
    I appear to have a small noise margin varying between 2.5 and 3.4 dB with the download speed of ca 18.0+ Mbps.    I have carried out a Quiet Line test on our corded phone and the line is perfectly quiet to the ear.   There have been no house wiring changes.
    Looking now at the Event Log it appears that the broadband disconnects in most cases are very regular every 30 mins - most odd?   Even between 01:00 and 06:00 hrs in the morning on 25 Feb my log shows 30 min drop out interval!
    Have BT made some kind of alteration to the Crowthorne exchange to cause the NM to sit below the normal level and for regular resets - seems unlikely?
    Back in Dec. 2012 in my thread "Re: Failure to Reset the Line to Original Rate following Cable Replacement" I was getting 15,876 kbps with a Noise margin of 6.0dB.  I still have the ferrite ring on the HH PSU cable.   It seems my line is being "squeezed" and giving me 18+ Mbps with drop outs.
    Should I request a Mod to reset my NM perhaps to a more reasonable value?
    Rodney Fry
    24 Feb
    ADSL line status
    Connection time            0 days, 04:28:21
    Downstream                 18,628 Kbps
    Upstream                      1,078 Kbps
    ADSL Settings
    Noise margin (Down/Up)            2.7 dB / 5.9 dB
    Line attenuation (Down/Up)        27.4 dB / 11.5 dB
    Output power (Down/Up)          28.5 dBm / 1.9 dBm
    Loss of Framing (Local/Remote)    0 / 0
    Loss of Signal (Local/Remote)    0 / 0
    Loss of Power (Local/Remote)    0 / 0
    FEC Errors (Down/Up)             14779 / 57780
    CRC Errors (Down/Up)              84 / 1446162
    HEC Errors (Down/Up)              955 / 0
    Error Seconds (Local/Remote)    57 / 203172
    Event Log
    Feb 24 18:02:32 2015    (28031.680000) Admin login successful by 192.168.1.69 on HTTP
    Feb 24 18:02:21 2015    INF 2015-02-24T18:02:21Z cwmp: cwmp_session: session completed successfully
    Feb 24 18:02:21 2015    INF 2015-02-24T18:02:21Z cwmp: cwmp_session: got empty envelope
    Feb 24 18:02:21 2015    INF 2015-02-24T18:02:21Z cwmp: cwmp_session: got envelope, len=0
    Feb 24 18:02:21 2015    INF 2015-02-24T18:02:21Z cwmp: cwmp_session: InformResponse is completed
    Feb 24 18:02:07 2015    (28006.010000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 24 18:01:28 2015    ERR 2015-02-24T18:01:28Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 24 18:01:27 2015    (27966.110000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 24 18:01:27 2015    (27966.060000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 24 16:05:20 2015    (20999.440000) Admin login successful by 192.168.1.69 on HTTP
    Feb 24 16:05:20 2015    (20999.440000) Admin login successful by 192.168.1.69 on HTTP
    Feb 24 15:41:05 2015    (19544.810000) Admin login successful by 192.168.1.69 on HTTP
    Feb 24 15:10:41 2015    (17720.690000) HTTP server returned error 404
    Feb 24 11:37:32 2015    ( 4931.230000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 24 11:36:59 2015    ERR 2015-02-24T11:36:59Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 24 11:36:58 2015    ( 4897.410000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 24 11:36:58 2015    ( 4897.350000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 24 11:07:49 2015    ( 3147.950000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 24 11:07:02 2015    ERR 2015-02-24T11:07:02Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 24 11:07:01 2015    ( 3100.000000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Feb 24 11:07:01 2015    ( 3099.950000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Feb 24 10:17:03 2015    ( 102.550000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Feb 24 10:16:27 2015    ( 89.240000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Feb 24 10:15:49 2015    ERR 2003-01-01T00:00:29Z cwmp: mt_cwmp: session error: Could not resolve host
    Feb 24 10:15:45 2015    ( 47.310000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    3 March
    Connection time        0 days, 20:04:53
    Downstream              17,990 Kbps
    Upstream                  1,078 Kbps
    Noise margin (Down/Up)    2.5 dB / 5.6 dB
    Line attenuation (Down/Up)    27.4 dB / 11.5 dB
    Output power (Down/Up)    27.5 dBm / 1.9 dBm
    Loss of Framing (Local/Remote)    0 / 0
    Loss of Signal (Local/Remote)    0 / 0
    Loss of Power (Local/Remote)    0 / 0
    FEC Errors (Down/Up)    5585 / 60053
    CRC Errors (Down/Up)    412 / 1492079
    HEC Errors (Down/Up)    16562 / 0
    Error Seconds (Local/Remote)    144 / 206517
    Message
    Mar 3 13:57:05 2015    (617497.220000) Admin login successful by 192.168.1.69 on HTTP
    Mar 3 12:58:31 2015    (613983.530000) HTTP server returned error 404
    Mar 2 17:53:34 2015    (545372.890000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 17:53:01 2015    ERR 2015-03-02T17:53:01Z c
    Mar 2 17:53:00 2015    (545339.080000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 17:53:00 2015    (545339.030000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 14:20:01 2015    (532560.490000) HTTP server returned error 404
    Mar 2 10:52:40 2015    (520118.800000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 10:52:06 2015    ERR 2015-03-02T10:52:06Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 10:52:04 2015    (520083.380000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 10:52:04 2015    (520083.330000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 10:24:40 2015    ERR 2015-03-02T10:24:40Z cwmp: mt_cwmp: session error: WGET TLS error
    Mar 2 10:24:40 2015    (518438.730000) WGET: Error connecting to host https://pbthdm.bt.motive.com/cwmpWeb/CPEMgt (66.193.112.93:443)
    Mar 2 09:06:41 2015    (513849.940000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 09:06:08 2015    ERR 2015-03-02T09:06:08Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 09:06:07 2015    (513815.930000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 09:06:07 2015    (513815.880000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 08:36:40 2015    (512049.360000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 08:36:08 2015    ERR 2015-03-02T08:36:08Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 08:36:06 2015    (512015.370000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 08:36:06 2015    (512015.320000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 07:06:44 2015    (506653.590000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 07:06:12 2015    ERR 2015-03-02T07:06:12Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 07:06:11 2015    (506619.930000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 07:06:11 2015    (506619.870000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 06:36:45 2015    (504854.390000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 06:36:13 2015    ERR 2015-03-02T06:36:13Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 06:36:12 2015    (504820.790000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 06:36:12 2015    (504820.730000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 06:06:48 2015    (503057.100000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 06:06:16 2015    ERR 2015-03-02T06:06:16Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 06:06:14 2015    (503023.670000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 06:06:14 2015    (503023.610000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 05:36:50 2015    (501258.910000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 05:36:18 2015    ERR 2015-03-02T05:36:18Z cwmp: mt_cwmp: session error: Could not resolve host
    Mar 2 05:36:16 2015    (501225.490000) danube_dsl_ioctl:88: Failed ioctl 250 errno 22
    Mar 2 05:36:16 2015    (501225.440000) danube_dsl_ioctl:88: Failed ioctl 270 errno 22
    Mar 2 05:06:51 2015    (499460.480000) RTNL: Received ERROR reply 'No such process' for message type 0x19
    Mar 2 05:06:19 2015    ERR 2015-03-02T05:06:19Z cwmp: mt_cwmp: session error: Could not resolve host
    Solved!
    Go to Solution.

    Thank you both for the replies.    I had wondered 'imjolly' if there could be a reason which you appear to confirm.   I have looked at the notes in the link 'John46'.   I have not noticed any problems with the HH2 or its PSU plug; the wireless link works well and my wife can now print to the HP Deskjet from her laptop.   Three of the Ethernet LAN sockets are now in use on the HH2 for a network.   One has the print server for the DeskJet and the main and standby Win 7 and Win XP machines occupy the other two.   
    Perhaps this home network might have some impact on the HH performance, but this should not really be so when the disconnects have also occurred in the early morning with everything switched-off, bar the router.   
    I shall continue to watch the behaviour and if it becomes too annoying perhaps a higher NM would be requested.    Games, videos and TV are not watched when such such interrupts could be unacceptable.
    Rodney Fry

  • Frequent connection loss

    Hi, recently my HomeHub has been disconnecting randomly and frequently. I checked the event logs and there appears to be a socket error of some sort.
    Does anyone know whats happening with this from the error log below?
    Thanks in advance.
    Aug 4 23:52:37
    2011
    (78042.020000) HTTP
    server returned error 400
    Aug 4 23:52:34
    2011
    (78038.570000) WGET:
    Error connecting to host http://192.168.1.77:2869/upnp/eventing/lohggrzxma
    (192.168.1.77:2869)
    Aug 4 23:52:34
    2011
    (78038.550000) HTTP
    server returned error 400
    Aug 4 23:50:04
    2011
    (77888.920000) HTTP
    server returned error 400
    Aug 4 23:49:53
    2011
    (77877.880000) HTTP
    server returned error 404
    Aug 4 23:49:32
    2011
    (77856.930000) Admin
    login successful by 192.168.1.83 on HTTP
    Aug 4 23:41:23
    2011
    (77367.540000) Socket
    error

    Quick search revelaed that the following use port 2869:
    Microsoft Internet Connection Firewall (ICF), Internet Connection Sharing (ICS), SSDP Discover Service, Microsoft Universal Plug n Play (UPnP), Microsoft Event Notification.
    Not sure why they would cause the hub problems, I would of thought it would of just limited your PC access.
    Hmm one for the tech heads me thinks..
    Check your exchange or major service outagesIf someone has given a helpful answer, please click on their Ratings star on the left-hand side. ***

Maybe you are looking for

  • My 2005, 60GB iPod color won't sync at all! Please help!

    I can't sync my iPod at all! I've looked everywhere for help and have found nothing. The only problem the iPod is having is this: When I click the 'Sync' button, nothing happens. There's no error message, nothing what-so-ever. iTunes reads the iPod a

  • Using USB 6341 device for frequency generation but level is droped when conect

    i am using USB-6341 Daq Device for frequency generation. The desired frequency is generated correctly but when i connect to other device the voltage level i means the Peak to Peak voltage of the frequency dropped to 0.6, 1 Volt and also the frequency

  • Cant connect a video confrence

    my friend and i both have the 20 in imac, ut we cant chat on a video together it says,"Date/Time: 2007-03-28 19:41:36.952 -0700 OS Version: 10.4.9 (Build 8P2137) Report Version: 4 iChat Connection Log: AVChat started with ID 1327156675. sgtscotty4444

  • Email account question

    I have 3 email accounts set up on my 3G, Google, MobileMe and Earthlink. All work fine EXCEPT Earthlink. I'm almost positive my setting are correct because it has downloaded some emails and I have been able to send one. However, most of the time I ge

  • Can I run a podcast and an app at the same time?

    Can I run a podcast and an app at the same time?