Where do I connect ethernet cable?

After connecting the ethernet cable to my Apple TV, where does the other end go? The ethernet connection on my computer, on my Apple Extreme, or on my cable modem???

Normally you'd connect it to your router via ethernet or wifi.
Depends if the cable modem or the Extreme is behaving as the main router, though potentially both could work.
You can even connect direct to a computer but would need to configure internet sharing for AppleTV to see the internet.
AC

Similar Messages

  • Back up is very slow on 2 tb time capsule. After 2 days only 60 gb of 320 gb completed. Have connected ethernet cable. Any suggestions?

    Back up is very slow on 2 tb time capsule. After 2 days only 60 gb of 320 gb completed. Have connected ethernet cable. Any suggestions?

    Yes, that's terribly slow.  You should get somewhere in the neighborhood of 20-24 GB/hour via Ethernet, assuming there isn't a lot of conflicting network traffic or your Mac's CPU is under very heavy load.
    Are you sure you're actually using the Ethernet connection, instead of WIFI?   To check, turn Airport off.  If the backup fails, it's on WIFI.  In that case, you need to set Ethernet as the "preferred" network, via System Preferences > Network.  Click the "gear" icon at the bottom of the sidebar and select Set Service order.  Then drag Ethernet above Airport.  When both Airport and Ethernet are on, that will make OSX select Ethernet over Airport.
    If that doesn't help, see #D2 in Time Machine - Troubleshooting.

  • How to connect ethernet cable to rMBP?

    Recently I've thought of getting a new router w/ ethernet cable, but the problem is that my retina MBP doesn't have a slot for the cable. Is there anything I can use to connect the cable to my computer?

    Yes: http://store.apple.com/us/product/MD463ZM/A/thunderbolt-to-gigabit-ethernet-adap ter
    Works great.

  • Connecting Ethernet cable causes shutdown

    Our 17" iMac suddenly shutdown and refused to start up - makes the start sound but shuts down after a few seconds.
    Managed to get it going by removing all cables and resetting SMU. Then connected to network thru Airport.
    The moment I reinsert the Ethernet cable the Mac shuts down. Thought it might be a faulty cable, but does the same with another cable which works fine on another Mac. Problem only happens when the cable is connected to the router, indicating it is not a short in the Ethernet port.
    I suspect the Ethernet card in the iMac. Any other suggestions?
    Any tests I can run to identify the issue?

    An iMac has a SMC and the steps for resetting the SMC are different from another Mac resetting the SMU. And apple has revised the process since the iMac Core Duos were introduced.
    Are these the steps that you used?
    Reset the SMC
    • Shut down the computer.
    • Detach the computer's power cord.
    • Press and hold the power button for 5 seconds.
    • Release the power button.
    • Reattach the computers power cable.
    • Turn on the computer.
    Run the Hardware Test on the original Install DVDs that shipped with your iMac.
    Dah•veed

  • Can't connect ethernet cable on Time capsule without messing Time Machine

    Hi All,
    I just bought a Time Capsule couple of weeks ago.
    I have a mac with time machine enabled on Wi-fi. I also have a vista that I can't get the wireless card to work properly... It keeps disconnecting and connecting from the internet.
    So I decided to plug an Ethernet cable between the vista and time capsule. Everything was working great, except that Time machine cannot connect to time capsule as long as that cable is there...
    Can't find anything to fix this...
    So either solution is fine by me: either some tips on why Vista keeps dropping the internet connection or why my time machine can't back up with an ethernet cable plugged on Time Capsule.
    thanks,
    marcelo.
    Message was edited by: caldas.family

    The warranty entitles you to complimentary phone support for the first 90 days of ownership.

  • Losing internet connection (Ethernet, cable modem)

    Hi,
    Lately (the past month or two), I am tending to lose my internet connection. (I never would before.) I connect via Ethernet to my cable modem. My ISP tells me that if I am getting 4 steady lights on my modem (with the 5th flickering), it isn't the modem. (I was thinking of replacing it.)
    Rebooting the computer will fix it. One minute it's fine, the next it may have lost the connection. When I lose connection, Network Diagnostics* says my built in ethernet and network settings are ok (green). The rest will vary (going on memory here), ISP, may or may not be green, Internet and server will be definitely out, when this happens.
    * I have dragged it out of wherever it was buried and have it now on my desktop. It is VERY convenient to check what is going on with my connection problems. (I guess I have created an applet?) I recommend this to all.
    I am considering re-installing the OS (archive and install) but am hoping someone can offer some suggestions for me to try short of that.
    Disk Utility and Tech Tool Deluxe don't indicate any problems. I can try the Apple Hardware Test. I am hoping this isn't a hardware issue as I cannot afford a new Mac or other repairs. I can live with rebooting if I have to.
    Thank you.
    John L

    The colors refer to what Network Diagnostics shows. Network Diagnostics is an Apple app that pops up when Safari has trouble connecting. I don't use Safari but loved having Network Diagnostics pop up so I figured out a way to use it independently of Safari. I dragged it out of wherever it was buried, put it on my desktop where it became an app and I use it at will to see why I am not connecting.
    It will show green, yellow or red as an indication of each aspect of the connection: built in ethernet, network settings, ISP, Internet and server (being Apple's server). Right now, all are green. When I can't connect, I'll have several going from server backwards that are red. If it can't figure out the status I get a yellow light.
    When I've asked my ISP why I am getting disconnected, they said if all 4 lights of the modem are steady (and the yellow one flickering), which they always have been when I've been disconnected, then it isn't the modem or them. They have good tech support and I trust them.
    I have replaced the modem once in the past and that fixed things. I may do it again.
    So, I don't know. I haven't tried the Safe Mode approach yet. I'll see if I can do that.
    Cheers,
    John

  • Connecting ethernet cable to macbook

    having wifi issues with MBA and wondering if internet can be acquired someway through a cable connection?

    Check out this link to the apple on-line store. It lists ethernet adapter/dongles, one for Thunderbolt/ethernet and another for USB/ethernet.
    http://store.apple.com/us/mac/mac-accessories/cables

  • How can I find my printer's ip connected (ethernet cable) to a time capsule which is in network extending mode ?

    I got a network printer connected to a Time Capsule which extends my wireless home network. But I can't manage to find out it's IP address nor i manage to find it on the network ! Am I doing something wrong ? Is there a way to tell Time Capsule which is the IP of the network printer ?
    Hope somebody can help me out !

    Most printers can print their status page.. on the status page is the current IP. I personally don't buy network printers that don't have a small LCD with enough menu to set things like IP address. And reveal the current IP.
    Is the printer set to dhcp? If so it will get an IP from the TC.
    Apple removed useful aspects of the old v5 utility which would give you a listing off all IP addresses passed out by the TC or connected to it.
    You can however do a netstat scan from your computer.
    In finder type in network utility into the search (apple have hidden it in a stupidly obscure location)
    In network utility run a netstat scan which should pick up the printer.
    One aspect of this, is that if the printer is in a deep sleep, power saving mode.. you may not pick it up.. certainly you should make sure the printer is awake and ready to run.. even if you need to reboot it.
    There will be a problem if the printer is manually set to the wrong IP range.. then it won't come up at all. To fix that you will need to actually read the printer manual.. and find out how to reset it to its defaults and start again.

  • Trying to connect an XBOX 360 to my airport base station via  ethernet cabl

    Hello,
    I have the older snow airport base station and was trying to connect my xbox 360 to it via an ethernet port. There are only 2 ethernet ports on the snow base station. one is being used by the cable coming from my dsl modem. the other free port i tried plugging into my xbox 360 to no avail. the xbox cant get an ip address. the open ethernet port on the base station is labeled with the circle logo. the one being used by my dsl modem has the two outer pointing arrows. I turned off the airport to my macbook and tried to connect my macbook to that port my xbox was in and it would not connect to the net either. Is it possible, i have the ports backwards. my wireless internet for all 3 mac computers works fine. Any help would be greatly appreciated!!!!
    Thanks!!!
    Vinny

    Yes, you have the ports connected backwards.
    The WAN port is labelled with the "circle of dots" icon, and must be connected to your DSL modem.
    The LAN port is labelled with the "double-headed arrow" icon, and that is where you connect ethernet cabled devices on your LAN.
    See Apple's article AirPort Base Station: About the WAN and LAN Ports
    What is surprising is that you haven't previously run into all sorts of problems with your existing setup. Once you cable things properly, you will likely have to power down your DSL modem and Base Station for a while (sometimes just an instant, sometimes overnight). After waiting, plug the modem into power and wait a minute. Then plug the base station into power and wait for it to restart.

  • Ethernet Cable Connection/MacBook Pro 2014

    How do you connect Ethernet Cable to MacBook Pro 15" [Mid 2014] existing Ports for direct wired connection.

    You need a Thunderbolt to Ethernet adapter http://store.apple.com/us/product/MD463ZM/A/thunderbolt-to-gigabit-ethernet-adap ter?fnode=b06858facdaae1a8480caa12bfda0f…

  • Given wireless range of Time Capsule is 150', will this work? Put DSL modem on phone line in garage, connect ethernet to small office bldg (125') and connect separate ethernet to main house (200'). Time capsule on each end (or Airport Express)? Thx

    Given Time Capsule wireless range is 150', will this solution work? In detached garage, connect DSL modem to phone line, then connect ethernet cable to DSL modem and run 125' to small office bldg. Connect separate ethernet cable to DSL modem and run 200' to main house. Put time capsule or Airport Express in each bldg resulting in separate wireless networks in each? Thanks.

    This will work very well. You can run a CAT5e (or CAT6) Ethernet cable up to 330 feet...or 100 meters...with virtually no signal loss.
    CAT6 costs a bit more, but will handle next generation Ethernet speeds, so if you have a choice, suggest that you opt for CAT6 cabling.

  • Can connect via ethernet cable, have good Airport signal but no connection

    Hey folks,
    Pesky problem. I'm trying to connect to my wireless airport extreme basestation and having problems. Everythings hooked up correctly and if I plug the ethernet cable from the modem directly to the powerbook it works fine. The odd thing is that my computer sees the base station, it has good signal, and it tells me I'm connected to the internet via airport.
    Why then can I not actually acess it? Any thoughts?...it's comcast high-speed in case that matters.
    Cheers,
    Sean

    Sean,
    ---- I was trying to get a link to another similar thread, where one of the experts (I'm not one of them) made some recommendations, but I can't seem to find it.
    ---- Is your Network Preferences selected for Airport as well as ethernet, and is Airport at the top of the list? Anyway, the fact that your direct connection PB to modem is working fine, may be the very thing causing your problem. The modem looks for the PB (MAC address?). So, you can do an hardware reset, or if not then unplug it for a good while (not tooggle the power on & off, but I think I saw someone even recommend overnight). Shutdown the AEBS & PB.
    ---- Then after you powerup the modem & it connects with the ISP (it takes just a short few minutes, you can watch the lights), then power up the airport, then after its connected up to the modem (again, a few minutes, you can watch the lights), bootup the PB.
    ---- I wish that I could have found the other thread for you, as the experts do an extremely better job of this.
    -------- Gino
    -

  • What is the process for connecting ethernet.  Have ethernet cable connected to stereo received for internet radio and Blue Ray. However Network System Preferences indicates ethernet not connected and has red dot to left.  Note Airport wireless is working.

    What is the process for connecting airport extreme ethernet?  I have ethernet cables connected to stereo receiver for internet radio and another to blue ray player.  The system preference network indicates "ethernet not connected" with red dot to left of this message.  The airport wireless works and has green dot to left of it.  The stereo receiver and blue ray player do not respond and give message not connect to internet.  Thank you.  /  cfpirate 

    It worked for me finally. I took out the DNS numbers in airport admin utility, and restarted the airport express. I do not remember putting the DNS numbers in, I wonder from where the airport express got those numbers.
    After restarting, it worked.
    Thanks!

  • WRT160Nv3 won't disperse my internet connection via ethernet cable

    I am trying to get it to where I can configure my router by having a hardwire connection to it but I can't even get it to disperse I wireless/wired signal whatsoever.
    I have done so many 30/30/30 reboots but I still can't get it to work even when I have it plugged in with power, ethernet from wall to router, ethernet from router to computer. It shows the X on my LAN Connection with W7 as my OS.
    I am pretty frustrated as I had it working earlier when I was screwing around putting DD-WRT firmware on it to prevent it from dropping my connections but really I don't know what to do. I am stuck. I'd appreciate any help.

    I think it was just being moody, it's now working and now I could finally customize the name of the network, the WPA key as well as the router settings on top of having wireless internet working again.
    EDIT: BUT when I hook up the ethernet cable from my router to my computer it still doesn't pick it up. But at least Wireless is now working for my 360 and my laptop.

  • Connecting to Airport Express via Ethernet Cable

    Dear Apple Support Community,
    My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
    The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
    However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
    I hope the above question makes sense.
    Thanks in advance for any feedback.
    Regards
    ST

    Hello Brian Hunt1. Welcome to the Apple Discussions!
    I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
    Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
    If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
    Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
    If this isn't your model, then check out the following vendor offerings:
    o QuickerTek
    o hField Technologies' Wi-Fire

Maybe you are looking for

  • New field in condition record for batch determination

    Hi Gurus, I'm trying to create a new batch determination transaction OMA1 and I have found that the fields I need are not displayed in either KOMGH Maintenance, KOMKH Determination header, KOMPH Determination item. My question is has anyone entered n

  • How do I resequence image filenames in an iPhoto event?

    My system configuration:  iMac i7 (2013), OS X Yosemite 10.10.1, current iPhoto app,  all updates installed, and iPhone 6 Plus. Within an event in iPhoto on my iMac, I have 300 photos.  I have taken photos at various times within a two year period. 

  • After All These Years, Outlook STILL Pops Up an "Enter Your Username" Dialog

    I used Outlook 2003 for 10 years.  It performed sufficiently, but had a few quirks. One of them was this:  Every now and then it would pop up a dialog, with fields already filled-in, showing the POP server and asking me to enter my username and passw

  • Problem in FS00 in displaying GL Account

    Hi All, I tried to view a GL account through the transaction FS00 and used the F4 help to get the values but the value which i choose from the F4 help does not get displayed and a error message saying 'GL account does not exists in the company code'

  • Need SAP training institutes in DELHI or Gurgaon

    Hi, Please give me the details of any good SAP FICO training institute in Gurgaon or Delhi. Also plz tell me how to award the points.