Why doesn't my E4200 wireless router show all attached devices when viewing the DHCP Client table?

I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results.
Other than a factory reset, any suggestions to get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago? Thanks!

barrysegal wrote:
I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results.
Other than a factory reset, any suggestions to get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago? Thanks!
It is strongly recommended that you upgrade the firmware to a smart wifi, which may resolve lot of bugs. You can also download the firmware here:
E4200v2 Linksys Smart Wi-Fi Firmware11/19/2012
Ver.2.1.39.145204
Download
18.3 MB

Similar Messages

Why doesn't my full email list show in a sidebar when I click 'write'?

Only a small number of addresses show up when I click 'write' instead of the usual full email list

''clan02 [[#answer-680924|said]]''
<blockquote>
Yes, I am talking about the Contacts Sidebar at the left of the Write window. It no longer is shown. This also eliminates the BCC option at the bottom of the sidebar. How can I regain BOTH features?
</blockquote>
You said "full email list". The "full" was misleading.

Macs show up as "unknown" on my router's DHCP Client Table

Both of my Macs, an Intel Mac Mini running Snow Leopard and a G4 iMac running Tiger show up as "unknown" in my router's DHCP client table.
All of my Windows PCs all show up with their computer names.
Is there a way to get my Macs' computer names to show up in the DHCP client table? The router is a Linksys RTP300.

Open Network System Preferences, click on the service you are using to connect to the network (airport, ethernet, etc), click on Advanced and go to the TCP/IP tab. There is a field for DHCP client ID. This may pass a name to the router and it may use it. I don't know.
Another option is the WINS tab. You can set the Netbios name (other than the default) and workgroup (and any WINS servers, if you know their addresses).

Missing Wireless Devices On DHCP Client Table

I’ll always have three wired devices connected on my router at all times and other wireless devices but I disconnect them when I'm done using them. I’ve recently left two wireless devices connect all the time but what seems after a week or so all my wireless devices stop showing up on my DHCP Client Table. Even though they stop showing up on the DHCP Client Table they still work fine and are still connected to the internet. I already tried rebooting my router and that seems to fix it. I have an E2000 Router with the latest Firmware: 1.0.04 I haven’t had any problems with disconnects or anything. My question is why is this happening and how do I fix it or does the router not support devices been connected for days? Thanks in advance.

There is no fix for this problem as it's not a problem. Maybe your wireless devices don't renew the lease at some point but just keep using the current IP address. Maybe it's a bug in firmware. But as you have noticed it does not cause connection problems. I think very often there are glitches in the DHCP table of various routers.

Linksys E2500 does not show any devices in DHCP client table

Equipment:
Old Westell DSL modem, still runs like a champ
Linksys E2500
home built desktop running Linux 12.10
We're having intermittent WiFi. This morning I finally sat down to do some troubleshooting. SOP for me is to reset both the modem and the router. Modem bounce went fine.
Before bouncing the router I did some nosing around and noticed there were no devices listed when I nosed throught the DHCP client table, not even the wired connection for my desktop. There should be 2 MacBooks, an Apple TV device and a Galaxy S4 showing up.
The other oddity - on a lark I switched the MacBooks over to the guest connection and there have been no problems with wifi since.
What gives...?
Any and all help will be greatly appreciated!

You make sure that the router's firmware is up to date. Reset it again since that's recommended after the upgrade and reconfigure the settings again. All devices in your network connected/ utilizing the router's DHCP server should be listed under the Clients Table.
For the intermittent wireless issue, try changing the wireless settings; ssid, wireless channel, and the security. For the channel, play around with channels 1, 6, 9, and 11.

My iphones and ipods no longer show up as devices when I plug into my computer to use itunes

Does anyone know why my iPhone and iPod no longer show up as devices when I plug into my computer to use iTunes?

Hi jacquelinex,
Welcome to the Apple Support Communities!
If your devices are not showing up in iTunes I suggest your read over and follow the troubleshooting steps in the attached article.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Have a great day,
Joe

Comcast just replaced my cable modem/wireless router. All devices connect properly except my iPhone 4. It shows itself to be connected to the network, but it does not load any web page. Resetting the iPhone does not solve the problem. Any suggestions?

Comcast just replaced my cable modem/wireless router. All devices connect properly except my iPhone 4. It shows itself to be connected to the network, but it does not load any web page. Resetting the iPhone does not solve the problem. Any suggestions?

Thank you for your response.
I had rebooted the router (several times, actually), to no avail.
I do not know the answer to whether MAC filtering is enabled on the router. Have tried to find info about that, but unsuccessfully. Router is an Arris TG852G, supplied by Comcast. I would be surprised if MAC filtering were the issue, since in addition to the computer, we have successfully connected several other devices to the wifi, namely an iPad, a Android phone and a Kindle Fire - all able to access internet pages through the wifi, and all without a need to add the device to a MAC address whitelist. To add to the mystery, the Comcast tech was able to connect his iPhone 4 to my network and access web pages. He was unable to connect my iPhone, however, after trying for some time.
I seem to recall reading somewhere that an iPhone cannot connect to a wireless "n" router, only "b" or "g". The Arris router is described as a n/g/b compliant router, and as noted the Comcast tech was able to connect his iPhone, so don't know why that would be the issue here.
By the way, my iPhone does connect wirelessly to my network at home. This difficulty is at a second home.
Any other thoughts would be appreciated.

Why doesn't my TestStand deployment installation show up under my Windows start menu of my target machine?

Why doesn't my TestStand deployment installation show up under my Windows start menu of my target machine?
I have successfully installed working deployments to target machines. However, I was expecting to see the installation listed as "My TestStand System A" in my start menu, but it is not. Am I misunderstanding something here?
Also, if I peform a different second deployment to the target station like "My TestStand System B", all of the LabVIEW files from my previous installation for "My TestStand System A" disappear from the target directory (c:\Program Files\My TestStand System A).
I am using TestStand 4.2.1 Professional on the development station with Windows XP and LabVIEW 2009.
Solved!
Go to Solution.

Thanks Paul,
That solved my second problem and inspired me to search deeper for the answer to my first problem. The answer is in the "Distributed Files" tab, "installer properties", "Create a Program Item" checkbox:
Wouldn't it be nice if this was automatically checked by default for the main sequence files? Wouldn't it also be nice if "Upgrade Code" was automatically regenerated by default whenever we saved the *.tsd file under a different name?
Thanks again,
Eugene
Message Edited by Eugene12 on 05-06-2010 04:27 PM

HT1245 Why does my caller I.D. photos show as a small thumbnail in the upper right corner and not full screen? I have used both photos I have synced and photos I have taken, yet others have full screen photo I.D.'s.

Why does my caller I.D. photos show as a small thumbnail in the upper right corner and not full screen? I have used both photos I have synced and photos I have taken, yet others have full screen photo I.D.'s. I have looked onlime at several threads and there are no real answers as to what I need to do or am doing wrong.

I am also having this issue.
I've just spoken to someone in the Apple Support Centre who advised me that since the product is in beta, he is unable to assist. I wanted to find out whether someone was able to delete the data for me, or 'reset' the photos app somehow. This apparently cannot be done. He suggested I provide feedback via the feedback page, which I will do, but to be honest doesn't fill me with a lot of confidence in the issue being fixed.
I also deactivated the service and waited the 30 days for the pictures to be deleted - this should have been completed in mid-January. Instead, my iCloud.com Photos page is now showing the photos that should have been deleted as grey squares, just as you described. I am also unable to delete these photos; every time I try, I get the same message about a server error.
I am also unable to disable the service by enabling and then disabling it on my iPhone. Each time I have tried this it hangs on uploading for several hours, with the progress bar not moving at all. When I disable it on my iPhone, the web app remains unchanged.
If anyone has had this issue and has managed to fix it, PLEASE share your wisdom. I am out of patience!

E3000 as an access point with an E3200 as the primary router not showing all connected devices

I recently rewired my home with cat 6. All network and telephone comes in to the basement. While most devices in the home were converted to LAN connections a few remain WiFi connected. The connections are as follows:
Cable modem -> E3200 ->High Speed Switch <--> E3000.
I purchased the E3200 to be the primary router. I'm using both 5.0 and 2.4 ghz connections. I set up my (existing) E3000 as an access point (AP) according to these instructions. I used the LAN-LAN setup so that all devices would be on the same network. Both E3200 and E3000 are at the latest firmware level. Both use the same SSIDs, one each for 5ghz connection and a second for 2.4 ghz connection. Almost everything is working but there are a few nagging issues.
1) A smart phone connected wirelessly to the AP shows as a LAN connection when viewing the E3200 DHCP client list
2) I set up a DHCP reservation for my network attached printer on the E3200. When it connects via the AP it is not assigned the predefined IP address
3) I can see the network attached printer on the E3000 MAC filter list but I can't see it when viewing DHCP clients or MAC wireless clients from the E3200 even though the printer is attached and working correctly.
I can understand the reasons for issue 1 but it seems that a client attached to a wireless AP should also show as wireless to the main router.

Well, let me know what IP addressess you have assigned to the network devices? Second if you remove the switch from the network (between E3200 and E3000) does the issue still persist... Once powercycle the whole network and then check whether it happens or not.

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. Any tips on how to do this?

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I have a iMac with a built in airport extreme card. Does the imac act as a wireless router so that I can connect to the internet from my iPad by tethering through my iMac?

I have a iMac with a built in airport extreme card. Does the imac act as a wireless router so that I can connect to the internet from my iPad by tethering through my iMac?

Depends which iMac exactly and your network setup, you can go into System Preferences and under the Sharing pane you can enable internet sharing from ethernet (or whereever you get your internet from) to Wi-Fi.

I have a net gear wireless router and a APE working great inside the house, but the wireless signal is weak in the backyard, can I get a net gear extender for the back and it will also send my music to the airport express?

I have a net gear wireless router and a APE working great inside the house, but the wireless signal is weak in the backyard, can I get a net gear extender for the back yard and it will boost our wo
Ireless signal and also send my music to the airport express? Or does the airport express work as a stand alone hub?

Trust me when I say this coming from 20 years of experience.
Get a powered external drive, format it 1 Partition Option: GUID and OS X Extended Journed as the format in Disk Utility.
Download and install Carbon Copy Cloner, clone internal drive to external drive.
Set a schedule to remind you to do it at least once a week, keep it near your charger.
When you plug your charger in, do plug the clone and power the machine up, set the display to sleep only,
CCC will do the rest.
If you want to boot from it, hold the option/alt and select it Startup Manager.
I've seen many TimeMachine and TimeCapsule nightmares and so far haven't seen a problem from anyone using a bootable clone.
It's simple, it's easy, it's more reliable and more powerful than what Apple does and it only takes plugging in a extra cable.
Make as many clones as you want, keep them time seperated, off site etc. etc.
Cables don't have network issues, clones can be verified in seconds merely by booting from them.
Clones protect your productivity, your up in seconds on a clone despite even the hard drive dying.
Software problem? No sweat, boot of the clone and reverse clone your problems away.
If you want to fuss and muss with half implemented TimeMachine and TimeCapsule network headaches then prepare to suffer.
I don't like to suffer, I bought a Mac not to suffer, but it appears you do with TimeMachine and TimeCapsule.
Most commonly used backup methods

Why doesn't my music transfer over to my iPad min when I sinc in iTunes?

Why doesn't my music transfer over to my iPad mini when I sinc in iTunes?

Hi Demo, thanks for the reply but I've solved it. Heres whet happened in case it can help some one else, when I was sinc'ing with my iPad mini through iTunes it wasn't putting my music on the device, everything else was good. After trying 5-6 times I reset the iPad and set it up as new. Originally I set it up from a phone back up.

Using Extreme in Bridge mode, can't see the DHCP clients if the D-Link router

I have an Airport Extreme attached to my DLink modem/router. I have configured the Airport Extreme in Bridge mode, and I was expecting all clients to show up in my D-Link router. Although the configuration works most of the time, I have been experience a few issues:
1. From time to time, computers attached (both Windows and/or Mac) complain about an IP address conflict. I can ignore the error and it works fine.
2. From time to time, I loose Internet connectivity, and I need to disconnect my computer and reconnect again to solve the issue. This is not necessarily linked to symptom #1
3. On my D-Link router/modem (which I only use to connect my Airport to my ISP), if I check the DHCP clients, I can see the Airport router connected and *some* of the wireless clients that connect through the Airport. The list changes quite randomly, and at times, I see the airport appearing twice with different IP addresses.
Any help configuring it "right" will be appreciated!
Alain

When the AirPort Extreme is in bridge mode, the AirPort Extreme is simply passing through the DHCP settings and services that are handled by the D-Link modem/router.
In other words, the D-Link device is in total charge of the DHCP services for devices on the network.
You might want to check with D-Link support to see if they have any recommended practices for configuing the modem/router when another router....the AirPort Extreme in this case....is being used in bridge mode on the network

Why doesn't my E4200 wireless router show all attached devices when viewing the DHCP Client table?

Similar Messages

Maybe you are looking for