Why is my iPhone 6 Plus home screen flickering and freezing up?
Why is my iPhone 6 Plus home screen flickering and freezing up?
Try these steps as needed:
1. Reset phone - press both home and lock buttons for at least 10 seconds, releasing when the Apple logo appears
2. Restore to factory settings:
Use iTunes to restore your iOS device to factory settings
3. Get warranty service from Apple in the country where the phone was purchased
Similar Messages
-
MBP 13" Screen Flickers and Freezes After Upgrading HDD
Hi There,
I have seen on here and a few other forums that people are having issues with graphics cards or overheating that is making the MBP screen flicker and freeze.
Mine has been fine until yesterday when I installed a new Seagte 1tb HDD. It works ok, but every now and then the screen starts to flicker, half of it goes black and the system freezes. Sometimes it's just for a few minutes, but sometimes I need to do a hard reset by holden the power button down for 5 seconds.
Here are the details:
MBP 5,5 13" (2008 I think - Can't remember)
Boot ROM Version:
MBP55.00AC.B03
SMC Version (system):
1.47f2
Version 10.6.8
2.26Ghz Intel Core 2 Duo
8gb 1067 Mhz DDR3 (Just upgraded, but before the hard drive and no issues)
1TB Seagate Momentus SATA HDD
As mentioned, I upgraded the RAM a week or so ago and it has been running fine. I put the new hard drive in last night and after a few hours, the flickering started.
I cloned the hard drive using SuperDuper and it all started up fine.
So far, I have verified and repaired permissions, checked SMART status and run a SMART Utility diagnostic. All comes back ok.
I cleared the PRAM and installed smcfan control as another forum with similar issues said it was a overheating problem and running the fan control program should fix it. I did that at 8am this morning and it has run great all day. Come 5.30pm, the flickering started and then it froze.. GREAT!!!!
It's so frustrating, I was really looking forward to having my MBP upgraded and running fast again.
Any ideas or tips would be very welcome.
Thanks in advance.set old HD. If problem will gone - you have weakened power supply or internal power converters. Yours new HD draw more power during spinup or something - so voltage on internal bus lowers and memory or videocard freaks.
5.30 PM looks like a time when there begins a lot of load on city energy grid - so voltage in wall socket goes a bit unstable, it may also add to problem.
if problem is gone when you are on battery power - its power supply. If it persists or get worse when on battery - its internal power convertors. -
MacBook Pro screen flickers and freezes after Snow Leopard/Safari 5 updates
Hi guys,
I have a silver 120GB 15-inch MacBook Pro from Summer 2007 with 3GB RAM and 25+GB free space which has recently begun to freeze irrecoverably. The first appearance of these symptoms seems to coincide with my installing the Snow Leopard 10.6.6 update via Software Update.
I'm not particularly well versed in computer technology, but will try to describe my problem as detailedly as possible.
What happens is this:
1. I start the computer as per usual, with only a couple of startup items. Everything's fine.
2. I start working. Use a lot of Safari 5 for browsing websites, often with some kind of Flash or "Flash-type" content such as banner ads, videos, even full Flash designs. I may also have programs such as QuickTime, VLC or an image editor open, if not necessarily "actively" doing anything. Everything's still fine - I'm able to both browse websites and watch videos as usual.
3. After a while of active working - say, 1-3 hours - I notice browsing websites gets a little choppy. Display features such as the file list view in Finder may or may not appear properly. The rotating wait cursor may or may not appear from time to time.
4. Immediately after symptom no. 3, the next time I start to watch a video, either via Safari 5 (say for example something on DailyMotion.com) or a file via QuickTime, something goes wrong.
Following no. 4, one of three things invariably happen:
5a) The video freezes and the entire screen flickers from black to the screen view very quickly two or three times, after which the computer or screen appears to freeze. The cursor still moves, but nothing reacts to it - open windows become completely unresponsive, nor does the top or any other menu react in any way to clicking. The "menu row" of application items, which normally appears when I move the cursor to the very bottom of the screen, doesn't appear. Restarting "blindly" by pressing the Off-button once and pressing R doesn't work. I'm forced to do a hard reboot, after which the computer is once again fine until the next two hours of active working. This usually happens ONLY when I try to watch a video in Full Screen-mode.
5b) I notice the video freezing only just in time, and am able to pause it and "esc" out of Full Screen-mode, and the computer remains operational. However, as soon as I again try to play video in Full Screen-mode, everything described in 5a. happens.
5c) The video stops playing, and the screen reverts momentarily to pale blue before switching to the login screen. I login again with my details, and everything appears to be fine again until the next two hours of active working. The computer "starts up" a lot faster than with a hard reboot. This usually happens ONLY when I've tried to watch a video in its original size, i.e. when not in Full Screen-mode.
This happens 1-4 times a day, and it appears to depend directly on how much work I've been doing on the computer. The less I use it in the course of a day, the longer it takes until the next time it freezes.
So, in a way, I'm able to replicate this problem. 95% of the time the screen has frozen while watching or starting to watch (usually already when starting to watch) video footage, but it has also frozen a couple of times just switching between e.g. Safari 5 and an image editor or browsing a website with a Flash banner ad or embedded video content (which however hasn't necessarily been playing); today, the screen froze when I tried to open a website made entirely with Flash.
Although it could be just a coincidence, I believe this issue first appeared when I updated Snow Leopard to 10.6.6 via Software Update alongside some other pending updates, including as far as I recall one for Safari 5. The update process appeared to have gone well at the time, though, and was not interrupted in any way. I have never had this specific problem with the computer/screen before, though.
I've read a couple of threads here regarding very similar issues with newer MBP models than mine, in which it has been suggested that the fault may lie in a malfunctioning NVIDIA GeForce graphics card. Now I've had that replaced already once because my screen went unexpectedly completely blank after a forced reboot 1-2 years ago (I don't remember exactly), but according to my System Profiler info the card still a GeForce 8600M GT. Can it be failing again?
I've also had some kind of a RAM card failure once. As far as I understood it, one of the RAM cards had fried and was preventing the computer from starting up. I replaced the bad 1GB card with a new 2GB one and the problem was resolved. Before the computer died, there were also other symptoms, but they were not similar to these.
I'm also doing the Apple Hardware Test tomorrow. Any other suggestions, though, than the graphics card?
*Could this have to do with Flash or Safari 5?* Just hear me out. Even though my computer has frozen from watching a video in just QuickTime, Safari 5 has always been open in the background at the same time, and more likely than not with websites with "Flash" content open. And come to think of it, before I performed the Snow Leopard and Safari 5 updates, I used to have daily problems viewing Flash video in Safari 5, the video content either suddenly showing up as "Plug-in Failure" or crashing the browser; I've had both Safari 5 and the Safari 5 Flash plug-in "quit unexpectedly" countless times in the past, almost daily. Sometimes the "Plug-in Failure" could be fixed just by refreshing the browser view; at other times, Safari 5 would stop showing Flash content altogether - Flash banner ads (such as Google ads), YouTube and other Flash videos, everything - until I quit and restarted Safari 5. BUT - since the day I updated everything via Software Update, I don't remember this happening; it never gets to "Plug-in Failure" now. Could it be worth trying to use e.g. just Firefox for a while or is there something (e.g. Adobe Flash) that I could try reinstall? Or am I just clutching at straws here?
Thanks for reading this long, long post!Do you have access to an Apple Store? If so, it may be worth making an appointment at the genius bar and having them run the test for the NVIDIA problem. Since your replacement logic board still has the NVIDIA GeForce 8600 M GT video chip, it could be starting to happen to your replacement logic board.
I also agree with all of CMCSK's suggestions. Freezing is often associated with hard drive problems. You might also want to run SMART Utility:
http://www.apple.com/downloads/macosx/systemdiskutilities/smartutility.html
You can download the demo and run it several times for free. It will give you a very comprehensive view of the physical health of your hard drive. If you still have the original one from 2007, it's getting pretty long in the tooth and may be approaching the end of its average useful life of 3-5 years. I just recently had to replace my original 2007 Fujitsu drive.
If your drive is headed south, and is also too small, it may be time to upgrade to a larger and faster drive.
The software update probably didn't cause the problems, but it may have exposed problems that were already in existence.
Good luck! -
Why the screen flickers and moves from one app to another by itself without being touch?
Why the screen flickers and moves from one app to another by itself without being touch?
Have you tried a reset to see if that fixes it ? Press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
-
Email address hacked via iphone. iphone locked home screen displaying my email password! and has been reset. now unable to restore iphone, saying i do not have permission
If you don't know your password, don't know your security questions and don't have a rescue address or don't receive a reset email, you should contact AppleCare who will initially try to assist you with a reset email or if unsuccessful will pass you to the security team to reset your security questions for you.
If you are in a region that doesn't have international telephone support try contacting Apple through iTunes Store Support. -
Hi my iphone 4 home screen keeps flashing on and off repeatdly. I will beonmy phone or in an app and it will go to a black screen and then light up to the home screen. Then the power off option will pop up. I have tried letting it die and recharging it and powering it off neither worked. Does any one have an idea on what this could be or what I can do?
If the Slide to Power Off option is coming up, that suggests your power button isn't working correctly and is sticking.
Best thing to do is bring the phone to an Apple store (make an appointment first) and have a Genius take a look at it.
~Lyssa -
why does my iPhone 5s shut down unpredictably and needs to be reset every time to start back up?
Hi Cyprus11,
Thanks for visiting Apple Support Communities.
If your iPhone is shutting down unexpectedly, I recommend going through these troubleshooting steps:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Best,
Jeremy -
Just upgraded to OSX 10.9 mavericks on macbook pro mid 2011 version. Having a big issue here that whenever my mac comes back from sleep, i.e after I open the lid, the screen flickers and there is an error of Finder not opening properly. Any fix to this?
My daughter has had her Razr for about 9 months now. About two weeks ago she picked up her phone in the morning on her way to school when she noticed two cracks, both starting at the camera lens. One goes completely to the bottom and the other goes sharply to the side. She has never dropped it and me and my husband went over it with a fine tooth comb. We looked under a magnifying glass and could no find any reason for the glass to crack. Not one ding, scratch or bang. Our daughter really takes good care of her stuff, but we still wanted to make sure before we sent it in for repairs. Well we did and we got a reply from Motorola with a picture of the cracks saying this was customer abuse and that it is not covered under warranty. Even though they did not find any physical damage to back it up. Well I e-mailed them back and told them I did a little research and found pages of people having the same problems. Well I did not hear from them until I received a notice from Fed Ex that they were sending the phone back. NOT FIXED!!! I went to look up why and guess what there is no case open any more for the phone. It has been wiped clean. I put in the RMA # it comes back not found, I put in the ID #, the SN# and all comes back not found. Yet a day earlier all the info was there. I know there is a lot more people like me and all of you, but they just don't want to be bothered so they pay to have it fix, just to have it do it again. Unless they have found the problem and only fixing it on a customer pay only set up. I am furious and will not be recommending this phone to anyone. And to think I was considering this phone for my next up grade! NOT!!!!
-
I installed Yosemite and now my computer is slow when logging in. Also when I type my password, a bar appears measuring the process and then all of a sudden the screen images are distorted. After that my home screen appears and everything seems normal. What can I do to fix this?
Here is what the etrecheck results are:
Problem description:
slow at start up, screen is distorted while logging in, it is fine after
EtreCheck version: 2.1.8 (121)
Report generated April 5, 2015 at 9:42:01 AM PDT
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
MacBook Pro (13-inch, Early 2011) (Technical Specifications)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 297
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.2 (14C109) - Time since boot: 0:7:0
Disk Information: ℹ️
Hitachi HTS545032B9A302 disk0 : (320.07 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / : 318.84 GB (174.85 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 319.21 GB Online
MATSHITADVD-R UJ-898
USB Information: ℹ️
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.devguru.driver.SamsungComposite (1.1.0) [Click for support]
[not loaded] com.logmein.driver.LogMeInSoundDriver (1.0.3 - SDK 10.5) [Click for support]
/System/Library/Extensions/ssuddrv.kext/Contents/PlugIns
[not loaded] com.devguru.driver.SamsungACMControl (1.1.0) [Click for support]
[not loaded] com.devguru.driver.SamsungACMData (1.1.0) [Click for support]
Startup Items: ℹ️
HP Trap Monitor: Path: /Library/StartupItems/HP Trap Monitor
Startup items are obsolete in OS X Yosemite
Problem System Launch Daemons: ℹ️
[failed] com.apple.ucupdate.plist
[failed] com.apple.watchdogd.plist [Click for details]
Launch Agents: ℹ️
[not loaded] com.google.keystone.agent.plist [Click for support]
[not loaded] com.hp.help.tocgenerator.plist [Click for support]
[not loaded] com.logmein.LMILaunchAgentFixer.plist [Click for support]
[not loaded] com.logmein.logmeingui.plist [Click for support]
[not loaded] com.logmein.logmeinguiagent.plist [Click for support]
[not loaded] com.logmein.logmeinguiagentatlogin.plist [Click for support]
Launch Daemons: ℹ️
[not loaded] com.adobe.fpsaud.plist [Click for support]
[not loaded] com.google.keystone.daemon.plist [Click for support]
[not loaded] com.logmein.logmeinblanker.plist [Click for support]
[not loaded] com.logmein.logmeinserver.plist [Click for support]
[not loaded] com.logmein.raupdate.plist [Click for support]
[not loaded] com.microsoft.office.licensing.helper.plist [Click for support]
User Launch Agents: ℹ️
[not loaded] com.adobe.ARM.[...].plist [Click for support]
[not loaded] com.facebook.videochat.[redacted].plist [Click for support]
[not loaded] com.google.GoogleContactSyncAgent.plist [Click for support]
User Login Items: ℹ️
iTunesHelper UNKNOWN Hidden (missing value)
AdobeResourceSynchronizer Application Hidden (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
Android File Transfer Agent Application (/Users/[redacted]/Library/Application Support/Google/Android File Transfer/Android File Transfer Agent.app)
HP Product Research Application (/Library/Application Support/Hewlett-Packard/Customer Participation/HP Product Research.app)
HPEventHandler Application (/Library/Printers/hp/hpio/HPEventHandler.app)
Internet Plug-ins: ℹ️
o1dbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
LogMeInSafari64: Version: 1.0.660 [Click for support]
Default Browser: Version: 600 - SDK 10.10
Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Click for support]
FlashPlayer-10.6: Version: 17.0.0.134 - SDK 10.6 [Click for support]
LogMeIn: Version: 1.0.660 [Click for support]
Flash Player: Version: 17.0.0.134 - SDK 10.6 [Click for support]
LogMeInSafari32: Version: 1.0.660 [Click for support]
QuickTime Plugin: Version: 7.7.3
googletalkbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
AdobePDFViewer: Version: 10.0.1 [Click for support]
SharePointBrowserPlugin: Version: 14.1.0 [Click for support]
iPhotoPhotocast: Version: 7.0 - SDK 10.7
3rd Party Preference Panes: ℹ️
Flash Player [Click for support]
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
7% ocspd
4% WindowServer
1% kextd
0% ps
0% securityd
Top Processes by Memory: ℹ️
137 MB Microsoft Word
120 MB Safari
86 MB ocspd
82 MB CalendarAgent
77 MB WindowServer
Virtual Memory Information: ℹ️
310 MB Free RAM
1.89 GB Active RAM
1.55 GB Inactive RAM
544 MB Wired RAM
1.13 GB Page-ins
8 KB Page-outs
Diagnostics Information: ℹ️
Apr 5, 2015, 09:32:47 AM Self test - passed
Apr 5, 2015, 09:30:05 AM /Users/[redacted]/Library/Logs/DiagnosticReports/AdobeResourceSynchronizer_2015 -04-05-093005_[redacted].crash
Apr 4, 2015, 01:12:41 PM /Users/[redacted]/Library/Logs/DiagnosticReports/AdobeResourceSynchronizer_2015 -04-04-131241_[redacted].crash
Apr 4, 2015, 08:13:57 AM /Users/[redacted]/Library/Logs/DiagnosticReports/AdobeResourceSynchronizer_2015 -04-04-081357_[redacted].crashReinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstalling OS X Without Erasing the Drive
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility and press the Continue button. After Disk Utility loads select the Macintosh HD entry from the the left side list. Click on the First Aid tab, then click on the Repair Disk button. If Disk Utility reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit Disk Utility and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Alternatively, see:
Reinstall OS X Without Erasing the Drive
Choose the version you have installed now:
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless. -
Why does my iphone have an itunes icon and a charger shown
why does my iphone have an itunes icon and a charger shown
Try this
If you can't update or restore your iPhone, iPad, or iPod touch
https://support.apple.com/en-us/HT201263
Best of Luck -
Mac air screen flickers and shuts down after startup
I recently loaded Lion on my 2011 mac air. After a week the computer started to have slow startup's, now when i turn on the computer the screen flickers and immediatly shuts down. How can i fix this problem.
correction the Mac Air is a 2010
-
Why is my Iphone 5 not opening safari and not recognizing my verizon data plan?
Why is my Iphone 5 not opening safari and not recognizing my verizon data plan?
What did Verizon say when you called them.
-
Why in my iPhone 6 has no FaceTime and how can i download it??? please help me.
why in my iPhone 6 has no FaceTime and how can i download it??? please help me.
If Facetime is not present on the phone you have, you cannot download it. The model of phone you purchased cannot have Facetime on it, period.
There is nothing to be done to download it - it's not possible.
~Lyssa -
Re: Yoga 2 Pro - Screen Flickering and Screen Blanking
sarbin wrote:
Moderator comment: Several posts were removed for contravening the Community Rules:
"No vendetta posts, or online campaigning. It is acceptable to state concern for how a particular Lenovo policy, performance, or procedure does or does not meet the expectation of a particular member, but it is not acceptable to use this forum in an attempt to broadly organize or incite members en mass, to cancel orders, return systems, undertake legal action or otherwise disrupt the normal business processes of Lenovo."
Rather than telling us what we can't do...how bout, as a mod, help by empathizing and perhaps suggesting solutions of courses of action for us.kbonura wrote:
I still feel like you can offer a suggestion rather than simply sweeping in and exerting your mod authority. This is a major issue that at this point there is no real evidence of lenovo addressing.
Are you an owner of a yogo 2 pro? If not, then you have no idea. You can't sit back and defend lenovo by modding us or hindering any potential efforts via discussion. You can't in good concience sit back and believe this to be ok.
Regarding paragraph 1:
1- If I had a suggestion to offer, I would have done so.
2- The moderation done to the thread (and the post moved here) was to apply conformance to the Guidelines.
3- Please see: http://forums.lenovo.com/t5/Idea-Windows-based-Tablets-and/Yoga-2-Pro-Screen-Flickering-and-Screen-B...
Regarding paragraph 2:
1- I have a Y2P, but don't have the issue described in the thread.
2- The moderation applied was not a defense. It was an application of the Guidelines.
Finally, again from the Community Guidelines, please recall:
"Extended debate with moderators or admins over their decisions with regard to moderation of posts is considered trolling."
Please feel free to continue the discussion, on-topic and within the Guidelines, in the ongoing thread.
Regards.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee. -
Screen flickers and goes black on boot up.
Have an older white MacBook that when I boot up, screen flickers and goes black, MacBook does power on.
Any suggestions?I am seing a similar issue with a 13" White MacBook.
Powers on ... chimes ... then screen goes blank as if the machine has gone to sleep. Hitting the Return key or the power button wakes it again, but only for two seconds ... and repeat!
Any help gratefully received!
Chris
Maybe you are looking for
-
Xml file not loading from different server
Hi, I have a simple flash banner that is pulling a number from an xml file on a different server. When it gets to the frame where the number should be it just says "transferring data from eckul.com" and will not actually pull in the number. Unfortuna
-
Can I download the software somehow since my MacBook Pro does not have a CD drive?
-
Error when deleting connector in CUP
Hi, When i try to delete connector I am getting message "Cannot delete because this is referenced by risk analysis" I tried by disabling the risk analysis and mitigation in CUP configuration,Still getting same message.I am unable to delete it.Any sol
-
Hi all, we seem to have an interesting issue when a header text from one order gets onto a header text of the billing document (invoice) of a completely different order, completely different customer and created by a completely different person. Does
-
My dictation didnt work this morning. I did a reset and NOW there is no MIC Icon at all..What happened and how can I fix..........? HOW can I get the mic back on the keyboard and get it working?? Please help