Why is the input mode greyed out when I try to create a virtual channel for my 1102?

I have set up a virtual channel for my SCXI-1102, and the input mode is greyed out with it set to "differential". I have already skimmed this forum for answers, and I have checked to verify that the mode slot under the AI tab for my MIO-E series card is set to nonreferenced single-ended mode. I then created a virtual channel with the device slot under the hardware column set to Dev1_SC1_MD1CXI-1102. At this point, as already stated, the input mode goes grey while set to differential. What's going on?

Hello,
All outputs from the SCXI module are measured in differential mode. You can still mix differential and single ended measurements (if you use the remaining channels of your daq board).
The easiest way to mix modes is with virtual channels. All SCXI analog input channels will be differential, while you can make other virtual channels differential or single ended. If you don't want to use virtual channels, you can use AI Hardware Config in LabVIEW to change the mode.
Hope this helps. Regards,
John N
Applications Engineer
National Instruments

Similar Messages

  • Why is the layers panel greyed out when I try to use PSE9 as my external editor?

    Recently, when I try to use Photoshop Elements 9 as my external editor in Aperture 2.1.4 the layers menu is greed out and the layers panel won't allow me to create layers.

    Hello,
    All outputs from the SCXI module are measured in differential mode. You can still mix differential and single ended measurements (if you use the remaining channels of your daq board).
    The easiest way to mix modes is with virtual channels. All SCXI analog input channels will be differential, while you can make other virtual channels differential or single ended. If you don't want to use virtual channels, you can use AI Hardware Config in LabVIEW to change the mode.
    Hope this helps. Regards,
    John N
    Applications Engineer
    National Instruments

  • Why is the column browser greyed out when viewing iPod music?

    Hello,
    I can not display the "column browser" for my iPod Touch, like I can for my iTunes Music Library (iTunes for Windows)
    To confirm we're on the same page: the column browser is the specific display/view with "Artists" and "Albums" filters (and optionally 'Genres" , "Composers" and a few other not-so-useful options) in Columns at the top of the screen: selecting different combinations allows you to easily filter the "results" panel below, which displays all the individual songs that match those filters.
    I have seen other questions on how to display the column browser, which relate more to the iTunes Library Music, opposed to the iPod touch music. (FYI the fix for the Library is to click "songs" and then the option for column browsing is available in "View/Column Browser/Show Column Browser")
    If i display the sidebar, and select 'Music' under my iPod Touch, it just displays ALL songs. The option for "show column browser" is greyed out and not selectable. If i hige the sidebar, and click "Music" in the top left column under the name of my iPod, i get the same view. If i click "Music" from the big centered bar at the top of iTunes (but below the standard File/Edit menubar) this just shows my Sync options...
    So question is: How do I display the column browser for my iPod music?
    If i can't, question is: Why did you hide this feature and can you please bring it back?
    And a general comment: Please let the brilliant Jony Ive loose on the iTunes design ASAP: it desperately needs a designer's eye to make this interface more intuitive. There are about 5 incongruous button/menu themes utilised at different places, and none of them are particularly well thought out. I'm a student of the school of thought where you can (if needed) utilise a few different interface design styles on one application to suit different users and different scenarious: but they need a talented designer to harmonise. The current iTunes is like years of changes piled on top of each other with no clear direction. Not an enjoyable experience!

    Hello,
    All outputs from the SCXI module are measured in differential mode. You can still mix differential and single ended measurements (if you use the remaining channels of your daq board).
    The easiest way to mix modes is with virtual channels. All SCXI analog input channels will be differential, while you can make other virtual channels differential or single ended. If you don't want to use virtual channels, you can use AI Hardware Config in LabVIEW to change the mode.
    Hope this helps. Regards,
    John N
    Applications Engineer
    National Instruments

  • The send button is greyed out when I try to text some but not all people from my iPod touch. Any ideas how I can fix this?

    The send buttin is greyed out when I try to text some but not all people from my iPod Touch. This happens even when they have iPhone 4s. Any ideas why and how I can fix this?

    This issue can be caused by the McAfee SiteAdvisor extension.
    Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Appearance/Themes).
    * Don't make any changes on the Safe mode start window.
    See:
    * [[Troubleshooting extensions and themes]]

  • Using the Android Reader app, why is the signature option greyed out?

    I have a client that has enlisted me to create 3 fillable PDF forms. I used FormsCentral to create these fillable forms, then I saved them as PDFs to my Dropbox. I opened the Adobe Reader app on my Tablet, and access the forms. As for the client, they are home builders, and these 3 forms are 3 different stages of the building process. They are using them to interact with the new homeowner. They want to do this on Samsung Note 10.1 tablets with Verizon data. There are 3 issues I am faced with fixing:
    1. The signing process is quite a process. Meaning too many clicks to setup and apply a digital signature according to the customer. And that is on a PC, because I am unable to use the "signature" function - the button is greyed out. Why is that?
    2. Once we resolve the above issue, then will there be a way to "lock" the form so that the customer's responses and selections are unchangeable? If so, how?
    3. Once the form is signed and "locked" (if possible), what is the simplest way to send the form via e-mail? I ask because they want there to be a way to setup the form to e-mail copies to the addresses that are entered into an e-mail field on the form. Sort of "auto-populate" the addresses as well as be able to set a predetermined address (back to their office) so that the results may be sent via mobile instantly upon completion.
    I know that is a lot to ask. Your help would be most appreciated!
    Thanks in advance, Rob

    (1) Why is the Signature button greyed out (disabled)?
    You used FormsCentral to create fillable forms and exported to PDF.  When exporting FormsCentral forms to PDF forms, FormsCentral adds "extended rights" to PDF forms so that users can fill out the PDF forms in Adobe Reader (which is a PDF viewer, not a PDF editor).
    The current version (11.5.0) of Adobe Reader for Android does not allow signatures to be added to any "Reader Extended" PDF documents (including forms).  We are actively investigating and trying to resolve the problem.
    (2) Is there a way to "lock" a PDF form?
    You can "flatten" a PDF form after the form has been filled out and signed by a customer.  Once flattened, it's not possible to change filled data or signatures.  When you try to email a filled PDF form (optionally with a signature), Adobe Reader for iOS will present the E-mail Document dialog with two options: "Send Original Document" and "Send Flattened Copy".  You can choose the "Send Flattened Copy" option.
    Unfortunately, the feature has not been supported in Adobe Reader for Android yet.
    (3) What is the easiest way to send a "flattened" copy via email?
    Because the issues 1 & 2 above have not been resolved, you are not able to do this in Adobe Reader for Android.  However, you can do this in Adobe Reader for iOS.
    First, you need to add a Submit button to your PDF form.  I am not sure if you can do this in FormsCentral.  But you can use Adobe Acrobat (a paid product) to add a Submit button.
    Setting action buttons > Add a submit button
    When your customer taps the Submit button in the PDF form, Adobe Reader (for iOS - for now) will present thee same E-mail Document dialog.  Once the "Send Flattened Copy" option is selected, Reader will launch the default Mail app and auto-populate email address(es) specified for the Submit button action.
    Please let us know if you have further questions.

  • Why is Encore 6.0 giving me the "blue screen of death" when I try to create a menu?

    When I purchased my student edition 6.0 (which I love by the way), Encore did not have any of the libraries loaded up on it. After reading some discussions, I downloaded the missing folders.
    Now, when I try to create a menu, my computer shuts down and gives me "the blue screen of death" as they call it (a blue screen with white writting, counting up to 100%, and saying Windows is preparing to crash...or something about the hard drive crashing....I can't remember because it goes off the screen so quickly).
    I've done this several times - my computer only does this when I try to create a menu in encore, and not in any other part of encore. It hasn't happened in any of the other programs either (Premiere Pro and Audition are the only other programs I have used so far), or any other times I have my laptop.
    Because of this, I am not too concerned since it seems Encore is the problem. However, I do not want any other problems to escalade from this either.
    Am I doing something wrong? Can someone please help me? I'm working on my Senior Thesis (a video) this year, and I really really cannot afford to have my computer crash on me.
    Please and thank you,
    Meghin

    Read Bill Hunt on BSOD http://forums.adobe.com/thread/772169
    -and an Encore fix http://forums.adobe.com/thread/1060443

  • I cannot input an Application ID when I try to create my own application

    I signed up for the free APEX hosting tonight. I cannot input an Application ID when I try to create my own application.
    This is where you enter a number to give your application a unique id. I have tried many numbers but none are accepted.
    Any ideas on what I should put here ?
    JIM

    Auto assign?
    Ta,
    Trent

  • The following error message appears when I try to create a PDF in Publisher:

    The following error message appears when I try to create a PDF in Publisher:
    PDFMaker cannot locate the Adobe PDF Printer's printer driver. Please re-install Adobe Acrobat 10.1.
    I have tried update patches to no avail.
    Can anyone please help?
    Thank you.
    Susan

    Hello Michael,
    My version of Publisher is 2010 and my OS is Windows 8.1.
    64-bit OS x64 based processor.
    I'm not too sure if this issue has arrisen when I upraded to Windows 8.1.
    My Dell printer(Dell all in one) has also stopped working due to a driver issue now not being supported.
    Thank you for taking the time to view my request.
    Kind regards,
    Susan

  • Why is the Image Verification display blank when I try to comment?

    Suddenly the IV window is blank when I try to comment on my blog (using firefox). If I write a comment, then enter gibberish into the IV confirmation field it returns a "no match" message (well sure, it would) but then this next time the IV image is normal and things proceed as they should and the message goes through normally.
    But it always takes two tries now, the first being used up trying to "match" to a non-existant IV image.
    The little icon next to the IV image field is "broken" in two on the first try also, then is whole on the second try, after the first failure.
    Evey time now it's this way, and just started today.
    iWeb 08 (2.04) - hosted on mobileme. OS X (10.6.7)
    What's up with that?
    thanks

    I just checked again this time connecting via Safari and got the same thing happening, only there is a "?" in the field where the Verification Image should be instead of the "broken page" symbol in Firefox.
    On the second try, after the "no match" error message, the verification image appears normally and it all works perfectly. It's like it has to be "nudged" into remembering how to work the way it should.
    I cleared the cache in firefox to no effect.
    The only thing I did prior to this happening was to change some page names in the website, which changed the navbar obviously, but it works fine as does everything else. What I did was change the page name "Blog" to "blog" to get consistency in the capitalization in the navbar. This changed the direct URL for the blog page, naturally, but that's not been a problem except for a few users who had to re-bookmark it to get there directly. Don't know yet if other users are having the same issue, but several comments have appeared without any feedback of a problem.
    I have iLife11 on its way to me and plan to upgrade to iWeb 3 when it gets here. Any hope that will straighten it out? (Yeah, I'm backed up with time machine, I read that post upthread about losing the whole enchilada.)
    The site appearance is fine as published, the blog works except for that one annoying and new little bug in posting comments online.
    I have no clue where to even begin looking at this point.
    If it was a Chevy, I could fix it.

  • Why is creative cloud loging me out when i try to down load a trial version

    it is creative cloud loging me out when i try to download a trial version ... my pop up blocker is turned off is there another setting i have to change... i didn't have this problem with downloading the trial of lightroom

    http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html
    Mylenium

  • Newbie question: Why is "learn sound model" greyed out when trying to remove background sounds in a file using the Spectral Frequency display?

    I am trying to remove background sounds in a file using the Spectral Frequency display. The first edit on a new file, this process works fine:
    1. use brush to cover sound
    2. right click, learn sound model
    3. effects/noise-reduction-restoration/Sound Remover
    The next time I try to remove another sound in the file, "learn sound model" is greyed out. I have to close the file and reopen to be able to make another edit. What on earth is going on? Can it only learn one sound model or something?
    I'm a newbie, so thanks in advance for your advice!

    My daughter has had her Razr for about 9 months now.  About two weeks ago she picked up her phone in the morning on her way to school when she noticed two cracks, both starting at the camera lens. One goes completely to the bottom and the other goes sharply to the side. She has never dropped it and me and my husband went over it with a fine tooth comb. We looked under a magnifying glass and could no find any reason for the glass to crack. Not one ding, scratch or bang. Our daughter really takes good care of her stuff, but we still wanted to make sure before we sent it in for repairs. Well we did and we got a reply from Motorola with a picture of the cracks saying this was customer abuse and that it is not covered under warranty. Even though they did not find any physical damage to back it up. Well I e-mailed them back and told them I did a little research and found pages of people having the same problems. Well I did not hear from them until I received a notice from Fed Ex that they were sending the phone back. NOT FIXED!!! I went to look up why and guess what there is no case open any more for the phone. It has been wiped clean. I put in the RMA # it comes back not found, I put in the ID #, the SN# and all comes back not found. Yet a day earlier all the info was there. I know there is a lot more people like me and all of you, but they just don't want to be bothered so they pay to have it fix, just to have it do it again. Unless they have found the problem and only fixing it on a customer pay only set up. I am furious and will not be recommending this phone to anyone. And to think I was considering this phone for my next up grade! NOT!!!!

  • Why is the delete on my Ipod greyed out when I try to delete files on the ipod

    When I try to delete files from my IPod the 'Delete' button is greyed out.  I swear I have mamge files but I do have Start iTunes when plugged ii.  What settings should I have in order to be able to delete files on my IPod?   Thanks

    With the iPod connected to the syncing computer, go to the Music pane for the iPod in iTunes and unckeck the songs you want deleted from your iPod and then sync. The following givesyou some information about syncing.
    iOS: Syncing with iTunes

  • Why is the filter gallery greyed out in Photoshop CC?

    I just installed PS CC and want to try some artistic filters but the Filter Gallery option is greyed out. How do I access the filter gallery?

    Is the image mode set to 8 bits/channel?

  • Why is my input volume greyed-out?

    I've opened a new project and opened a new Real Instrument track. I have an external mic plugged into the Mac's audio input, and I know it's working 'cause I can see some volume on the input level indicator. I have selected Line Input in the System Preferences Sound pane. In the New Track Info window, I've selected Vocals, No Effects, Channel 1 (Mono), etc. but my input volume slider is greyed-out, can't move it from it's current level, which is the lowest possible. The only way I can get more input volume is to go back into the Sys. Pref. Sound pane and slide it there. How come?
    Powerbooks G3 & G4, iMac G5, plus Windows   Mac OS X (10.3.9)  

    http://www.thehangtime.com/gb/gbfaq2.html#volumesliderdimmed
    Also,
    http://www.thehangtime.com/gb/gbfaq2.html#micline

  • Why is the automatic updater greyed out?

    Not only is the automatic updater in IPhoto greyed out, I can also not manually download and install the update.  I am asked to download from the app store which does not recognise that IPhoto is installed and asks me to pay for a new copy.... any ideas why????

    Where did you purchase the version of iPhoto you have? Have you looked in teh App store under purchases?
    LN

Maybe you are looking for