Wi-fi status light

I recently downloaded OS X Maverick all went seemless with the exception of the desktop WI-FI status light stays illuminated whether connected to the internet or not ?

Where is this Wi-Fi status light? I sure don't have one on my MacBook Pro!
Clinton

Similar Messages

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
Power off the AirPort by pulling the power cord
Wait a minute or two
Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
Release the reset button and allow a full minute for the AirPort to restart
Now try to configure the AirPort again. If you continue to see the same symptoms as before, the AirPort will need to be replaced.

HT3728 No status light at all on Airport/Time capsule. I can plug internet cable directly into bac of my MAC and have internet access no problem. Is my Airport dead and need to be replaced??

I have NO status light on my Airport/Time Machine, I unplugged the internet connection from back of Airport and plugged directly into my MAC and am able to get to the internet just fine.
The Airport is almost 6 years old
Is my Airport dead and just need to get a new one??

Is my Airport dead and just need to get a new one??
Unfortunately, yes. On the upside, your Time Capsule lasted about twice as long as normal.

My airport time capsule did not set up successfully, and then status light flash amber

Hi, Guys
I am the first time user of the time capsule, please help how to proceed?
I have set up the first time and my airport time capsule does not set successfully, then I try to reset to factory setting. After this, although I use the ethenet cable to connect the router to the airport, the status light flash amber, always, even after the reset.
Also, I can see that airport time capsule base station from the wireless network when airport is plugged in. However, when I want to access to it.

Thanks for your guidance, but the product is really anoying. First, I am sure that the airpor utilities is 6.3.
and I also follow your instruction that to set the IPv6 as local link mode. But still get the same error as mentioned in my first post.
Therefore, I have tried to use the bridge mode but could not find it, and therefore still can not set it up successfully, even though I reset the factory again(press the reset button 5 secconds at least).

Solid amber status light on ASA 5505

Hi,
I have a Problem with a ASA 5505
when i power on the ASA the Power LED change to green and the Status light to solid amber.
There is no Console output or anything else.
Is this a DRAM or Flash Problem?
What can i do ?
thanks a lot!

Had the same problem, and this fixed it for me. If i plug the power supply into the ASA then plug the power supply into the wall, i get the amber status light and green lights flashing failure. However if I plug the PSU into the wall first, then wait a few minutes and plug the tiny little adapter(Fail on the adapter design Cisco) into the ASA 5505, ta-da it works! It seems like the PSU needs to build up the power before being plugged into the ASA. I don't know for sure, but this works for me. I never wanted to plug in the tiny adapter first because i was afraid of it arcing in the adapter and that causeing problems, but this method works for me, hope it helps.

Apple TV 3 Status Light turns ON and stays ON when I turn ON my Broadband Modem. How do I stop this ?

Since I updated my Apple TV 3 to 5.1.1, the Status Light turns ON and stays ON when I turn ON my Broadband Modem. How do I stop this ?
At the moment I have to go to the HDMI channel that my ATV 3 is connected to, wake the ATV, then put it back to sleep, to turn OFF the status lght.
When I first got my ATV I did not have this problem, when it was running 5.1.0.
I sent in a Feedback form, but they only as the option to select the OS version of a NON iOS device.
Is there a fix to this that wont involve me leaving my modem ON all the time ?
I turn my modem OFF when I am not using the Internet because I am a bit paranoid about the security of the data on my devices, and if I leave the modem turned ON all the time it might make me an easier target for hackers etc. { This is NOT part of my question, just explaining why I turn my modem OFF ( I feel safer ) }
<Edited by Host>

The ATV3 does that to me when I turn on my TV. the light goes on and stays on. If I switch to the ATV3, it seems to be half asleep with the light on ... I do wish Apple would enable the HDMI CEC and then everything would make sense. I've turned off my wireless and on again but the ATV3 light does not turn on automatically for me.
As you pointed out, I guess this could be a small glitch on the new firmware/software update... I wonder if this could be fixed by doing a restore from the iTunes app. I might give it a try tomorrow and see what happens...
Cheers!

So i connected my ipod shuffle to my apple computer and the status light on my ipod shuffle shows that it is charging but when i look for it on the pc dock or in itunes it doesn't show it at all.... so what do I do???

so i connected my ipod shuffle to my apple computer and the status light on my ipod shuffle shows that it is charging but when i look for it on the pc dock or in itunes it doesn't show it at all.... so what do I do???

If you have not already, I would shut down (power off) your computer. Do this to Reset your shuffle
http://support.apple.com/kb/HT1655
Start up computer. Run iTunes. Connect shuffle.
If you have added a new USB device recently (since the last time it worked properly), you may want to try disconnecting it to see if that makes any difference.

When I plug in apple tv the status light just blinks amber and nothing appears on the screen

When I plug in my apple tv (first gen) the status light just blinks amber and nothing appears on the screen. The status light never turns white and won't stops blinking amber. I've tried to over ride this with the remote, resetting it and trying to revert it to the factory settings. Is there a way to wake it up or is it a lost cause?

Welcome to the Apple Community.
The system looks like it's unable to start up, this could be software but more likely hardware, either way unless it will start up there is nothing a user can do to resolve this.

My Apple tv status light is blinking fast - how do I troubleshoot?

my Apple TV gen 2 status light is blinking fast and I am not able to see anything from my Apple TV - how do I troubleshoot? What I read on the Apple site is that my Apple TV has issues. My Apple TV is hard wired to my Ethernet network. It is connected to my TV using an HDMI cable. It worked in the past but when I turned it on today it did not work. I have not used it in several months and we had a bad thunderstorm here a couple weeks ago.

I'm having the same problems as you. Any solutions? This is what i'm facing
1. No video signal at all
2. Plugged in power cable only, there is no light
3. Plugged in micro usb, there is flashing light
4. Restore via iTunes is sucessful but problem still persists

Apple TV loses picture output and status light flashes rapidly after 5 minutes hooked up via HDMI - DVI cable

Apple TV connected to a 2005 50" plasma monitor with DVI input via belekin HDMI to DVI cable. Unit worked perfectly long enough to get it connected to the wireless network and begin the itunes registration process when there was a loss of signal message on the screen from the monitor and the Apple TV status light flashed rapidly and continuously. Reset and reboot yeilded flashing rapid status light and no output detected from the monitor. I contacted support online and was told to return the unit to the apple store. I returned home with another brand new apple tv and connected it in the same manner with exactly the same results. Is there something with the HDMI - DVI interface that is causing this? Are there known issues with the HDMI - DVI connection to Apple TV with older plasma monitors?

The Apple TV doesn't actually support DVI. Some have managed to get it to work others have had varying issues with it.

Mac Pro 3.1 status light is always on

Hello
I have a Mac Pro 3.1
Since last week I have a problem, and could't yet found the solution. Sometimes (most of the times, actually) the Mac Pro doesn't boot and just stops after the chime (just as it was powered off). But what I found strange is that the white status light is always on (not blinking, always on) from the moment I connect the power strip.
I've run multiple times the Apple Service Diagnostic tests (running then again at this moment) and there´s absolutely no error reported.
I've changed memory, video card slot position, everything I could think off, but still haven't found a solution.
Thank you for your help

I will try the UPS as soon as I can get one working (it seems my trusted Ellipse Max 1500 isn't working anymore). But how can it explain the fact that the light always stays on?
Another thing. In one of the last reboots to seemed that the Mac Pro couldn't find the startup disk. Past the chine nothing happened. After I started again with the alt key pressed and chooses the correct disk it appears to be working (the light problem keeps the same).
So, maybe there's a problem with the SMC, could it be? Yes, I did the SMS (and PRAM) reset, but the problem keeps the same

Why does my Apple TV 2 status light periodically come on when it's supposed to be asleep?

Hi Community.
Apple TV 2 asleep. TV off. No remotes bring pressed, no 'activity' I can see but perodically my Apple TV status light will come on for a minute then go off.
I can't say exactly how much it happens but I notice it several times a day. If I switch on the TV the Apple TV is not 'on' even though the light is on. If I press the remote and wake it, it wakes and works as normal.
What's going on? Surely if the Apple TV is registering network activity or something like that, there's no need for a status light? Doesn't seem like a very Apple behaviour.
Thoughts?
Thanks, Rodí

not sure about atv2 but I have an atv1, and since these devices are never truely off,
when you see them as off it's just the video output which is disabled.
they are present on wifi all the time also when you see it as asleep
when a computer is on for enough time it will crash sooner or later
even googles servers require a reboot once in awhile
so my logic is that when my atv1 light up where it was asleep before
it's because it crashed because if I pull the plug and put it back in thats
what happens too

Status lights in DVD Pro

Just recently I have started having an issue in DVD pro. I complete a sequence in FCP save it export it as a Quicktime movie then open DVD pro import assets, and the two status lights next to the audio vieo files are yellow instead of green. I have been doing it this way for some time, and it has always worked fine, and the two little lights were always green until just recently. Can somebody tell me what might be causing this.
Thank You,
Bob Bowers.

Seeing how yours is a DVD-SP question, you might get more and better responses by posting in the DVD-SP forum: http://discussions.apple.com/forum.jspa?forumID=952
-DH

Status light in AP1130 doesn't work!!!!!

I have a AP1130, it's working fine, except the status light is always green, even when there are clients connect to it through wireless in which case it should be blue.
I've upgraded the firmware and the same problem still happens.
Does anyone knows how to fix this??
Thanks in advance,
regards,
Hugo

Is it possible that you are actually connected to an adjacent LWAP? In other words, can you unplug the LWAP in question and still connect via wireless?
The reason I ask is that there is a known issue where the 1131 LWAP turns status LED turns light green when it is not actually connected to the WLC.
This behavior ocurrs when the LWAP is not receiving an IP address via DHCP.
- John

Flashing Status Light

Hi,
I switched on my Mac Pro today (after using it yesterday) and it won't start; no starting chime or anything. All I have is the status light above the ON switch is flashing continuously; there is no pattern to the flashing as suggested in the user guide - it just flashes constantly.
I have disconnected all external devices and re-seated the memory cards and PCI Card for my eSATA drive but the Mac will not start and the light continues to flash.
I'd be grateful for any ideas or suggestions.
Thanks,
Cliff
Brighton, UK

Specifically which mac pro model do you have?
There are other diagnostic leds on the processor board besides those near the dimms. Look carefully around for others that may be lit.

HT200154 how do you turn off the apple TV box? There doesn't seem to be an off button. The status light stays on.

how do you turn off the apple TV box? There doesn't seem to be an off button. The status light stays on.

Usually, when you put it to sleep mode, the status light will turn off. To put it into sleep mode, go to Settings.
If you want it completely off, then I guess the only way to do it is to pull the electric plug.

Wi-fi status light

Similar Messages

Maybe you are looking for