Wicd does not automatically connect to eth0

Wicd works fine using my wireless network. It does not automatically connect to eth0 when I plug in a cable, but I can connect to it by pressing connect manually.
I already have ethtool installed (do I need to run ethtool as a daemon???)

stabele wrote:I have two maybe naive question:
1)are you connected to wireless network before you plug in ethernet cable? If yes, than wicd does not automatically switch to wired network. Maybe you can get it done by custom scripts wicd support for each connection, but I never used this thing in wicd.
2) do you have disabled in rc.cong interfaces you want wicd to manage INTERFACES=(!eth0 !wlan0) ?
Thanks for your answers, 1) no I'm not connected to wireless, and 2) eth0 is disabled.
I found out it works fine if I connect eth0 manually and then I can remove and plugin the cable all I want and it automatically connects. This is because dhcpcd is already running for eth0 so maybe I should run dhcpcd eth0 in a boot script (although I think wicd should do this).

Similar Messages

  • IPad (3rd generation) does not automatically connect to wi-fi.

    iPad (3rd generation) does not automatically connect to wi-fi.  It is fully updated to 5.1.1 but you have to manually connect after turning off and back on.  I also have an iPad 2 with the same OS but it automatically connects.  The wi-fi has no security. 

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Windows 8.1/IE 11 Does Not Automatically Connect to the Internet

    Windows 8.1/IE 11 Does Not Automatically Connect to the Internet
    I can't find the dial and redial options anywhere.
    I' m connecting through PPPOE but only manual.
    I know that in windows 7/8 a program like IE9 or IE10 could connect to the internet, but now it just says that I am not connected to the internet.
    How to connect automacally to the internet and how to let IE to connect automatically to the internet, and why I don't have the options for dialing and redialing like in Windows 8?
    Thank You

    Hi,
    Sorry for my dilatory reply, what does your mean that IE dialing to connect to internet?  Did your system can connect to Internet? or just IE 11 couldn't connect to internet. you can
    check your IE poxy setting in Connections of Internet options.
    If you encountered any IE problem, you can try to reset IE for test to resolve this problem.
    If you need further assistance on this particular issue or any other Windows related issue, let us know and we will be glad to assist you.
    Roger Lu
    TechNet Community Support

  • Wifi does not automatically connect on iMac

    When turning on my imac intermittantly the wifi internet connection does not automatically connect and when this happens i have trouble manually connecting it, resulting in me turning airport wifi on and off upto 5 times.
    I am running OSX Lion V 10.7.4.
    Any sugestions?

    Hi, this has worked for a few...
    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    old... http://docs.info.apple.com/article.html?artnum=106653
    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    10.7…
    System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
    10.5.x/10.6.x/10.7.x instructions...
    System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
    The interface that connects to the Internet should be dragged to the top of the list.
    Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
    For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
    208.67.222.222
    208.67.220.220
    Click OK.
    Also, turn off IPv6:
    System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6
    Or whatever Interface you use.

  • Does not automatically connect to wireless network anymore

    Mac Book does not automatically connect to know networks any longer.

    Hi sashton,
    When troubleshooting Wi-Fi connectivity issues, I find the following resource has the most relevant information:
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    http://support.apple.com/kb/HT4628
    Furthermore, you may want to avoid giving your network a common name. While the following article (and excerpt) refer to iOS devices, the same applies for your Mac:
    Avoid giving your wireless network a common name (SSID)
    http://support.apple.com/kb/HT4450
    If you were to give your wireless network a common name (SSID), users of your network who use iOS devices [sic] and are away from your network would run the risk of joining a different network with the same name. Having joined the unexpected network, they would be exposed to potential data theft.
    Because of this security issue, Apple maintains a list of common or ambiguous SSIDs, including the default SSID for many commercially available access points, as well as the SSIDs "wireless" and "default". If your network's name is on the list, any iOS device [sic] that joins the network stores the access point's BSSID and associates it with the network's SSID. Subsequently, it will only auto-join the network if the access point's BSSID matches the information the device has stored. This avoids joining a different network with the same name.
    Therefore, you may want to refer to the following article when configuring your Wi-Fi router:
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    Thanks,
    Matt M.

  • Yoga 13 does not automatically connect to Wifi at times

    My yoga 13 does not automatically connect to WIFI at times thought it has been saved to automatically connect. It will connect after I click on the WIFI icon in the desktop and then it sees the WIFI network and automatically connects to it. Though it is not a big deal it is minor inconvenience that I have to click that icon at times when internet doesn't work. This shouldn't be the case for a laptop that retails over 1000 bucks. Any suggestions?

    This happens to me too. I haven't found a solution yet either.

  • Iphone 4 does not automatically connect to Airport WIFI from i Mac if it does it will not connect to Safari

    iPhone 4 does not automatically connect to my iMac's Airport network. When I do get connection Safari will not open on iPhone?

    Have you tried BT's Support Communities? http://community.bt.com/t5/BB-Speed-Connection-Issues/unable-to-connect-iphone-t o-BTHomeHub-Wi-Fi/td-p/1816

  • Does not automatically connect to recently used WIFI networks

    Recently purchased 13" Macbook Air, with Lion installed. All's well, except upon start-up or waking up from sleep mode, it does not automatically re-connect to the WIFI network it was just connected to. Instead, I'd have to manually find the network to select it. (Incidentally, some of my friends who also use Macbook Air and Macbook Pros have also experienced this periodically.)
    Another strange thing, is that there is this one particular WIFI network at work, that I've successfully connected to before, upon return the next time, all of a sudden, the network isn't even visible anymore. My OS5 iPhone sees it fine, and never has a problem, but repeatedly this happens. Other people at work who also use Macbook Pro and Macbook Air also encounter the same problem. People who are using PCs don't have the same experience.
    Is there a setting somewhere? I have "Remember networks this computer has joined" checked, and I see the particular network listed as ones I've joined.
    Any light that can be shed on this would be greatly appreciated. It's very frustrating, especially Airs don't have a built-in ethernet port. I hate using the adapter, it steals one of my USB slots.
    Thank you in advance!

    Hi sashton,
    When troubleshooting Wi-Fi connectivity issues, I find the following resource has the most relevant information:
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    http://support.apple.com/kb/HT4628
    Furthermore, you may want to avoid giving your network a common name. While the following article (and excerpt) refer to iOS devices, the same applies for your Mac:
    Avoid giving your wireless network a common name (SSID)
    http://support.apple.com/kb/HT4450
    If you were to give your wireless network a common name (SSID), users of your network who use iOS devices [sic] and are away from your network would run the risk of joining a different network with the same name. Having joined the unexpected network, they would be exposed to potential data theft.
    Because of this security issue, Apple maintains a list of common or ambiguous SSIDs, including the default SSID for many commercially available access points, as well as the SSIDs "wireless" and "default". If your network's name is on the list, any iOS device [sic] that joins the network stores the access point's BSSID and associates it with the network's SSID. Subsequently, it will only auto-join the network if the access point's BSSID matches the information the device has stored. This avoids joining a different network with the same name.
    Therefore, you may want to refer to the following article when configuring your Wi-Fi router:
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    Thanks,
    Matt M.

  • My 5800 does not automatically connect to Bluetoot...

    Hey Folks,
    I have the following problem with my 5800 X-Press Music: I paired my Bluetooth Headset with my mobile and everything works fine. Then I accepted the question about automatic connection between headset and mobile. But when I turn the headset off and on, my mobile does not (re)connect to the headset. I did a lot of research and found a lot of topics where people says that this is a bug in the bluetooth firmware. I just upgraded my firmware to the newest version, but that did not solve it. 
    any hints and help would be appreciated, but answers from nokia officials would be the best for me!
    Thank you in advance

    It's more likely to be a bug in the bluetooth earpiece. I too have one and it does reconnect automatically when I switch it on, provided bluetooth is switched on on the phone, obviously.
    Message Edited by grschinon on 29-Jul-2009 12:14 PM
    Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

  • MacBook Air does not automatically connect to network

    The MBA automatically connects to the network when the network broadcasts the SSID, however when I don't broadcast the SSID then I have to manually setup the network in order to connect to it. On a Windows PC running XP there is a checkbox that allows the computer to connect to networks that are not broadcasting the SSID. Is there any such thing for the MAC?

    You can setup a network location on your mac and select a preferred network for the mac to join.
    However there is no reason not to broadcast an SSID. It does not make you any more secure as wifi sniffing software can detect hidden networks just as easily as none hidden ones. It gives a false sense of security. The only wifi protection you should consider using is WPA or WPA2.
    Is there any such thing for the MAC?
    FYI a MAC is not a Mac
    MAC=Media Access Control
    Mac=Macintosh

  • T60 does not automatically connect to wireless profile at bootup any more

    Probably my rose-colored-glasses mistake again. 
    I let the ThinkVantage system updater install most of the latest updates last night including the
    wireless adapter software.  Now, when I boot up, my PC no longer automatically connects to
    my wireless profile.  The radio is on and it is obvious it knows the network is there because it
    is highlighted in the Access Connections menu with a Connect option.
    It connects just fine when click Connect. 
    It will still automatically switch between ethernet and wireless when I plug and unplug the
    ethernet cable even if I have specifically disconnected from the wireless connection before
    plugging in the ethernet cable.  It also automatically connects when I log off Windows and log back on.
    Is there a setting some place that controls whether it should automatically connect to a
    wireless profile at bootup?
    I love the brain-dead online FAQ about this exact problem.
    It says to click the Connect button if it happens.
    Well, duh!  What do I do to make it automatically connect like it used to?
    I tried unchecking the "allow computer to turn off the radio" setting as other suggested.
    But, my problem is not the radio being off.
    Thanks 

    Hi sashton,
    When troubleshooting Wi-Fi connectivity issues, I find the following resource has the most relevant information:
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    http://support.apple.com/kb/HT4628
    Furthermore, you may want to avoid giving your network a common name. While the following article (and excerpt) refer to iOS devices, the same applies for your Mac:
    Avoid giving your wireless network a common name (SSID)
    http://support.apple.com/kb/HT4450
    If you were to give your wireless network a common name (SSID), users of your network who use iOS devices [sic] and are away from your network would run the risk of joining a different network with the same name. Having joined the unexpected network, they would be exposed to potential data theft.
    Because of this security issue, Apple maintains a list of common or ambiguous SSIDs, including the default SSID for many commercially available access points, as well as the SSIDs "wireless" and "default". If your network's name is on the list, any iOS device [sic] that joins the network stores the access point's BSSID and associates it with the network's SSID. Subsequently, it will only auto-join the network if the access point's BSSID matches the information the device has stored. This avoids joining a different network with the same name.
    Therefore, you may want to refer to the following article when configuring your Wi-Fi router:
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    Thanks,
    Matt M.

  • AirPort does not automatically connect when IP settings assigned manually

    Hello,
    Since I manually set up the TCP/IP settings in System Preferences > Network > AirPort, I have found that upon waking my iBook, it no longer connects to our AirPort network automatically. Instead I have to go to the AirPort menu and select our home network manually. As you can imagine, this is somewhat annoying.
    I imagine it's designed this way as when you enter another wireless network you aren't going to want to use those same manual TCP/IP settings.
    Is anyone aware of a workaround for this?
    I'm not using DHCP as I want the iBook to retain the use of the '10.0.1.200' IP address, which the AirPort Extreme points port 80 traffic towards. 'DHCP with a manual address' seems like the way to go. However, with this setting my iBook is unable to determine the subnet mask or router address (why this happens is beyond me, since surely the iBook gets this information via DHCP?).
    Any ideas? Am I missing something really obvious?
    Jon.

    Huh?
    I have I think. "Configure via IPv4:" is set to "Manually". I have then manually set my IP address to "10.0.1.200", the subnet mask to "255.255.255.0", the router to "10.0.1.1" and the DNS servers to my ISP's DNS servers. I have no problems with the Internet connection. I don't think the problem lies here, if that's what you are talking about.
    The problem I have is that, when my iBook wakes (or is logged in) it doesn't automatically connect to our wireless network. Instead I have to manually select it from the AirPort menu, which is annoying. If I use the "Configure IPv4: Using DHCP" option it all works fine, apart from the fact that I can't use the IP address I want to use.
    It seems to me that if you configure manually AirPort won't auto-connect upon wake, for fear of connecting to a different wireless network using your manual TCP/IP settings.

  • Airport Does Not Automatically Connect

    I recently put a password on my router (NetGear). Since then, when I wake my computer from sleep or turn it on, the Airport no longer automatically connects to my network even though I have it set up in the System Preferences to "By default, join a specific network" (which is my network, with the password typed in). Any suggestions? Thanks.
    Ken

    I recently put a password on my router (NetGear). Since then, when I wake my computer from sleep or turn it on, the Airport no longer automatically connects to my network even though I have it set up in the System Preferences to "By default, join a specific network" (which is my network, with the password typed in). Any suggestions? Thanks.
    Ken

  • My macbook air does not automatically connect to my network when i go on safari

    I just replaced the hard drive in my macbook air, now when I try to log on to safari, it says I am not connected to my wireless network and I have to go to system preferences and pick my network and log on. Even though I lock the changes after I log off and come back I have to do it all over again. Any suggestions?

    WiFi, Internet problems, possible solutions

  • Does not automatically connect to my network anymore

    When I first got this Laptop a few weeks ago it would connect to my wireless network immediately. However, I downloaded a windows network program by mistake last week and, even though I deleted that program, I now have to get into Network Magic , go to view available networks and wait for a few seconds for my linksys network to show up. Then it connects with no problem.
    What can I do to get it back to the way it was?

    dvenneman wrote:
    When I first got this Laptop a few weeks ago it would connect to my wireless network immediately. However, I downloaded a windows network program by mistake last week and, even though I deleted that program, I now have to get into Network Magic , go to view available networks and wait for a few seconds for my linksys network to show up. Then it connects with no problem.
    What can I do to get it back to the way it was?
    Hi dvenneman,
    Make sure that at least another computer in your Network has Network Magic installed.
    Uninstall Network Magic from the laptop and reboot. the computer. For the XP Computers.
    Use Explore and remove the following folder and its sub-folders:
    \Documents and Settings\All Users\Application Data\Pure Networks
    \Program Files\Pure Networks
    Still using Explore manually clean out your \Temp Folders. Run Disk Cleanup.
    Run a Windows Registry Cleanup program to clean your Registry.
    A good one, is TuneUp Utilities 2010 at http://www.tune-up.com/products/tuneup-utilities/ 
    Reboot.
    Make sure that you are connected to the Router.
    Reinstall Network Magic.
    Use another computer to Activate this copy of Network Magic.
    Report back.
    thecreator - Running Network Magic version -5.5..9195.0-Pure0 on Windows XP Home Edition SP 3
    Running Network Magic version -5.5.9195.0-Pure0 on Wireless Computer with McAfee Personal Firewall Build 11.5.131 Wireless Computer has D-Link DWA-552 connecting to D-Link DIR-655 A3 Router.

Maybe you are looking for