Window s 8 consumer problem with hp laserjet p1005

hello everyone
today my second day with consumer preview
my printer was working will with developer preview
but now
i installed the software of hp full package and the printer where installed then i am trying to printing any page at give's me a side tap says
" Printing Error "
and not printing and in the queue says print-error
i tried uninstalling and reinstall ( Not working )
itried reinstall windows 8 consumer ( Not working )
i aslo tried my printer on other pc ( Uses windows 7 ) to sure the printer health its worked on windows 7 and one developer preview.
i tried microsoft fixit and hp problem detector every thing says no problem ,, but there's a problem
need help pls
thanks

Really Thanks God
i Found solution of this problem Randomly only by praying
The solution
Connect The p1005 printer to a pc have windows 7 and print a page with it and get the cable connected to windows 8 after that and go to control panel > hardware and sounds > Device and printer > hp laser jet p1005 Right click > Printer properties > ports > uncheck bidirectional support then press ok and print ,, it works
Note : after doing the pervious steps if u turned the printer off u will need to connect it to windows 7 pc again and print and connect it to windows 8 it will work without the pervious steps //
it seems like if windows 7 gives it information that is reseted after turn it off
we wish windows 8 to solve this problem nearly
That is the Original post page : http://answers.microsoft.com/en-us/windows/forum/windows_8-hardware/laserjet-p1005-will-not-print/34...

Similar Messages

Printing problems with HP Laserjet P1005

everything seems to be ok with my printer HP Lasejet P1005, but it just doesn't print. The works are in the gueue and error messages continually is "set the new toner cartridge" althrough I've changed the cartridge already. Also there is a message "HP:s part number"
What can or should I do??? Help!!!

Hi @rlp48,
I see by your post that you are getting the error message "set the new toner cartridge" and you have already changed it with a HP toner. I would like to help.
I would do a hard reset to see if that will resolve the issue.
Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
This ensures the printer is receiving full power and may help this situation.
Try and print a hardware self test on the printer to find out if it is a hardware or software issue.
Open and close the lid 5 times quickly. It should print out a page with lines on it.
Did it print the self test?
If the self test page printed, clear the Spool folder and restart the Print Spooler and try printing again.
How to Clear Current Print Queue In Windows Vista & Windows 7.
Download and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it. Find and fix common printer problems using HP diagnostic tools for Windows?
What operating system are you using? How to Find the Windows Edition and Version on Your Computer.
Are you using Genuine HP Toner?
What were the results when you ran the Print and Scan Doctor? (did it print or scan, any error messages)
Please provide in detail the results if you are still having issues.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

I have a problem with HP laserJet P2055dn... Has anyone resolved this issue??

I have a problem with HP laserJet P2055dn...
Since I changed OX to Mavericks, my macpro does not connect to the HP printer (laserJet P2055dn)
Has anyone had this issue? Anyone resolved this??

How do you force the printer driver to reinsall?
I delete the printer and re-added, but nothing changes.
All the forums topics concerning driver updates reference the App Store, but I cannot find anything there.
Nor I can download the driver from the vendor website, as it also redirects me to the App Store, where nothing happens.
I am new to Mac, so the question may be a silly one.
Thank you for your help.

Both xp and windows 7 have video problems with my VGA connection using TV

both xp and windows 7 have video problems with my VGA connection using TV as my monitor when it gets to starting up windows no matter what version it will not I have let my mac on all night and still says starting windows or the windows 7 logo and nothing else will happen also when I use a 3rd patty software like peraills or other it works like a charm how to fix it?

To map the drive on your computer click on Start - RUN - type "\\192.168.1.1" and click ok... When prompted for Username and Password type "admin" and click ok... Now you will be able to see the folder which you have shared on your router, right click on it and select "Map network drive" and click on finish.
Now it will map the drive on your computer and you should be able to transfer the file from your computer to the USB drive.

Satellite A500-1C0 - Windows has detected a problem with HDD

Good day,
Notebook shows me that Windows has detected a problem with HDD. The notebook is slow and the chops. And when you turn it shows me Smart Failure predicted on hard disk 1. Toshiba MK 5055GSX - (S2). Can you help me? (Im CZ)
http://img684.imageshack.us/img684/8434/smartm.jpg

Hi Konyga,
If you already get a warning about internal HDD before Windows starts I would recommend exchanging it and backup all data as fast as possible.
Is your notebook still under warranty?
If yes you can get a new HDD from an authorized service provider. This would be for free because its covered by warranty. Everything what you have to do is contacting an ASP.
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an ASP

Problem with HP LaserJet M1319f MFP installation

Dear support team and community members,
I'm currently trying to install HP LaserJet M1319f MFP connected by USB on Lenovo Q190 machine /Intel Core i3 processor/ running freshly installed Windows 7 Enterprise 64 bit with Bulgarian
language pack, all current updates, Microsoft Forefront Protection /I also tried to disable the Real-time protection/, UAC disabled, administrator account, IE 11, .NET Framework 4.5.1.
The priter was working correctly with Windows XP.
I downloaded the driver package from the official hp website.
After the installation process reach the "Copying files to the hard drive" stage the installer return error Printer Software Installer stopped working.
I tried running with Administrator privileges and/or Windows XP SP3 compatibility mode, but the same error occurs.
I tried Microsoft Fix It software for install/uninstall drivers too,but with no luck either.
I cleaned the cashe and temporary files around 10-15 times.
Windows update is not helping with the drivers too.
I tried to extract the files from the installer and manually add the printer and got error that the installation was not successful and below it says The file was not found /if I recall it correctly/
After that I tried HP Print and Scan Doctor software, but it displays that there is no driver installed and redirecting me to the driver download page.
I tried the Driver Wizard software too, but it returns that this model is no supported.
I tried to change the windows startup to "Selective startup" with "Load startup items" unchecked and all non-microsoft services disabled, but with no success.
Under Safe mode the install won't complete because of the Print Spooler service not running, which is running normally otherwise.
The "ntprint.inf" file is present in the "Windows\inf" folder, the registry HKLM\SYSTEM\CurrentControlSet\Control\Print\Enviroments\Windows NT x86 has only Drivers and Print
Processors subkeys and the registry HKLM\SYSTEM\CurrentControlSet\Control\Print\Monitors has only Local Port, Microsoft Shared Fax monitor, Standard TCP/IP Port, USB monitor and WSD port subkeys.
The folders Windows\System32\spool\PRINTERS and Windows\System32\spool\drivers\W32X86 are empty.
I ran sfc /scannow in cmd with administrator privileges, but there was no integrity violations.
I tried to disable the IE component, but no luck either.
So now I’m out of any ideas how to connect that **bleep** thing… I hope that someone can help me with this issue.
Currently the devices without installed driver in the Device Manager are "Hewlett-PackardHP LaserJet M1319f MFP" /Hardware IDs USBPRINT\Hewlett-PackardHP_La28A1 and Hewlett-PackardHP_La28A1/
and HP Scan /Hardware IDs USB\VID_03F0&PID_5817&REV_0100&MI_00 and USB\VID_03F0&PID_5817&MI_00/
I forgot to mention that I tried all kind of variations with these solutions with and without printer plugged in.
Thank you very much in advance for any kind of guidelines.
Best regards,
Ivan

Hello Rick,
Just as I mentioned above I'm using Microsoft Forefront Protection, but had no luck with disabling the Real-time protection - it is disabled,
but that chanage nothing.
The downloaded driver is for Windows 7 64 bit.
I did write to HP but I still got no answer from them... I already checked that support page, but I didn't get any information corresponding
to my problem, not to mention that a lot of that page is just copy/paste from another product and it's not relevant to that model.

Printing problems with hp laserjet 1018

- printing problem with my hp laserjet 1018 (no *.pdf files!), all other documents were printed
- hp photosmart premium c309 works with all file types
Windows 7 64 bit
Adobe Acrobat Pro 10.1.7
Acrobat Reader 11.0.3

Also having other "permission" based problems as well. Other people cannot open my PDFs even though I have not used any security. I'm thinking about getting a previous version of Accrobat Pro and installing that.

Problem with my laserjet m1217

i had problem with my router. My hp printer does not see the signal anymore and refuses to print and copy.
please help.
laserjet m1217 nfw mfp.
I am working with a pc and windows.
thank you

You have to reset the printer.

Windows 98 resource & memory problems with Developer/2k v2.1

Hi All
I have just started developing with Developer/2000 v2.1 on
Oracle v7.3. I recently purchased a Dell Inspiron 3500 notebook
PC running Windows 98 (64M RAM, 4.3G HD). I have had continuous
problems with the system running out of system resources and/or
memory.
The problem seems to be with both the development and runtime
programs. If I run the Form Builder and then exit it, the system
information program reports that the F50DES32.EXE is still
running, plus there are a load of 32-bit driver files left in
memory. The same problem occurs with the runtime, in that once
it's loaded, even after taking the exit option, the F50RUN32.EXE
is left running in memory. This would not be so bad if
subsequent loads of either program recognised that the program
was already running, but they do not so you end up with multiple
copies of the programs running. At the moment, with regular
changes, recompiles and reloads of the runtime going on, I have
to reboot the PC on average about once every 30 minutes.
I cannot find anything on either the Microsoft or Oracle web
sites about this problem, and really I'm not sure who's to
blame. I guess development on Windows 98 is still pretty young.
However, this seems to be a fairly serious problem and is
certainly having a major impact on productivity!
Am I missing something in terms of Oracle parameter settings or
in the way Windows 98 is set up? Has anybody out there had
similar problems? Can anybody help??
Thanks
Billy
null

I also observed something like this- but it was a programming error. I was using ADODB in LabVIEW to run SELECT statements and retrieve data from recordsets. My program would gradually consume more and more RAM over time. This was plainly visible on NTs Task Manager. My problem was that I was simply forgetting to close/destroy many of the object references. This would also sometimes cause my system to crash when I stopped the program and exited LabVIEW (or exited the run-time engine if it was an exe).
I might suggest you go through the program and make sure you use the Automation Close function to close the appropriate references.
Its especially important to close all "Fields" and "Field" references.
Also, I found that running the GET ROWS method or GE
T STRING method on a recordset works much better than retrieving data using "Fields" and "Field" objects... its faster, easier, less prone to causing problems, less trouble with references and stuff.

Printing problem with HP Laserjet 2550

I have an HP Laserjet 2550 which is having problems with my Macbook Pro with 10.6.3
Snow Leopard has the drivers for the HP 2550. So when I added the printer it picked up the drivers.
The problem I am having is that it send the job to the printer but the printer does not print it. When I restart the printer on startup it prints the job. I have to do this every time.
Is the problem with the Mac or the printer?

Have you run Software Update to check that you have the latest HP drivers? They have done a couple of revisions since SL was released. Of course, if you are still running 10.6.3 SU will come up with many other updates some of which might be relevant to the problem.
You might also do some maintenance - repair permissions, etc. This could make a difference. There are lots of other steps that might be taken but try these first.
Neville

Problems with hp laserjet 4ml on solaris 7

Hi out there,
I`ve got a problem with a hp laserjet 4 ml on "solaris 7" (AXUS ultrasparc WSU1D/200):
After I had installed the driver with the hp jetadmin-tool, it`s only
possible to print as a root-user, as a normal user nothing happened, the printjob never reached the printer, but with the
lpq-command I can see it in the printqueue. With "solaris 2.6" it worked fine. Thanks a lot.

Hi,
Check out the permissions for printer related directories and files.
Regards,
Dharani
SlashSupport India Pvt Ltd.
Hi out there,
I`ve got a problem with a hp laserjet 4 ml on "solaris
7" (AXUS ultrasparc WSU1D/200):
After I had installed the driver with the hp
jetadmin-tool, it`s only
possible to print as a root-user, as a normal user
nothing happened, the printjob never reached the
printer, but with the
lpq-command I can see it in the printqueue. With
"solaris 2.6" it worked fine. Thanks a lot.

Problem with HP LaserJet 4L and Leopard

4L will not print with Leopard except under following circumstances:
If I unplug the 4L, then replug and reset via Print & Fax preference,
then, it will print 1 page and stop. Will not print any more until I go through the unplug,replug,reset procedure. Then, I get 1 more page. Etc,etc. The unprinted pages appear in the printer queue. I have used this 4L happily going back through many Mac's to the old Duo. Any ideas?

I am having a problem with my HP Laserjet 6L. I use PowerPrint's Serial to USB cable. The computer recognizes the driver, but prints garbage. Does anyone know how to fix this?
With Tiger I used to have the problem where after each print job I would have to unplug the USB cable and plug it into the other USB port. This might be a work around for the other respondants.

Windows 8.1 Compatibility Problem With CP1518

I have an HP LaserJet CP1518ni printer that I purchased 2 or 3 years ago. We recently had our previous computers MOBO go out on us and had to replace our computer. I decided to purchase a machine with Windows 8.1. When I tried to install my printer, it will not recognize the printer at all. I have tried installing/uninstalling, different drivers, the DOT4 communications software, everything that I can think of. It just won't communicate with the computer. In searching the internet, I have found two different places on HP's website that it discusses compatibility. In one place, it says that it is USB and Networking compatible with Windows 8.1 and refers me to the Universal Print Driver. In the other place, it is shown in a table that says my printer is not compatible with Windows 8.1. I would hope that this is not the case, as the printer is not that old and was fairly expensive to purchase for a home office. Has anyone had this issue with compatibility with Windows 8.1? And, has anyone found a way to get Windows 8.1 to communicate with the printer?

Hi ClarkUELS,
Welcome to the HP Forums.
I see that you are having a bit of an issue attempting to install the printer on to your Windows 8.1 computer.
I suggest that you start from scratch and turn the printer on and the computer on. Connect the usb cable to the computer and then the printer. You will then see a Found New Hardware connection. Go ahead and run the add a printer and select the CP1510 series. This is a generic print driver and once it is installed you should be able to print with no issues.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Windows Server 2003 and problem with SSL connection (TLS)

Hi,
We are forcing a problem with SLL/TLS connection on a machine Windows Server 2003 SP2.
We spent hours trying to solve it without any result.
SYMPTOMS
No SSL connection can be established in any application since last year, e.g.:
we cannot do any windows update, because there is a time verification over SSL on the windows update website (there is an error that the time is incorrect while it is up-to-date)
we cannot open any website in Internet Explorer over https
when we try to connect to the SQL Server (database SQL 2008 hosted on the same server) with Management Studio it fails with an error: "A connection
was successfully established with the server, but then an error occurred during the pre-login handshake.(provider: SSL Provider, error: 0 - Could not
contact LSA)(Microsoft SQL Server)"
in a custom applications which sends requests over https we receive an error: "Could not establish trust relationship for SSL/TLS secure channel"
Everything seems to point at some SSL problem somewhere deep inside Windows.
We installed several patches, but without any result.
Can anybody help?
Regards,
Dawid

Hi, thanks for answers,
- In IE both SSL2.0 and TLS1.0 are checked. We tried to disable TLS1.0 - with no results.
- In HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\SecurityProviders\Schannel both SSL2.0
and TLS1.0 are enabled. We also tried to dislable TLS1.0 on the Client side - with no resuts.
- In
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\SecurityProviders\SCHANNEL EventLogging is set to 3, so it should log warnings
and errors. But we cannot find any related logs in EventLog
Unfortunately we are still in the same place.

Itune isntallation error massage in windows" There is a problem with this windows intaller package. A program required for this install to complete could not be run. Contact you support personnel or package vendor." please help

the subjected massage is coming every time i try to run itune setup on my windows 7 PC, the error massge is " There is a problem with this windows intaller package. A program required for this install to complete could not be run. Contact you support personnel or package vendor." i downloaded three times the setup from apple site same massge is coming, and when i try to install icloud client the same massage appeared, please help.

Did you try to repair Apple Software Update?
That is the important thing to try.
If that doesn't work we would need to try something else.

Window s 8 consumer problem with hp laserjet p1005

Similar Messages

Maybe you are looking for