Windows 8 does not remember secondary SATA hard drive letter

So, I bought an HP Pavilion with a 1TB HDD with Windows 8 installed. I burned the recovery disks, wiped the 1TB (Seagate) drive and installed a 250GB (WD) drive. I installed the WD as the primary boot and OS, and formatted the Seagate as a basic drive for
storage. I reinstalled from the recovery disks, and the OS went exactly where I wanted it to, but the Seagate doesn't list in the My Computer display. It does appear in the BIOS, and it does appear in Disk Management.
I searched the internet and found the tips about using Disk Management to assign a drive letter to the second drive. SUCCESS! Or so I thought. I can see the second disk in disk management, and can successfully assign a drive letter so that the drive appears
in My Computer; but after any/every reboot, I have to go through the same process over and over and over again. Windows 8 is not "remembering" the drive letter settings for this particular drive.
It doesn't seem like a big deal, but this drive is intended as a shared drive for the "Homegroup" so that everybody can use it as storage. Not everybody in the small office is familiar or comfortable with going through this, so I need the system
to "remember" the disk settings all of the time.
The 1TB Seagate has the following properties:
Disk type - Basic
Partition style - MBR
File system - NTFS
Does anyone have any ideas? Suggestions?
Thank you!

Hi alcisco70,
The drive letter miss after restarting the computer, right?
I would like to suggest you update its driver firstly, and then do the following:
open a command prompt with administrator privileges, then type:
Diskpart
List disk (you will get detail disk info, if you only have one disk, it will show disk 0)
Select disk 0
List volume (you will get detail volume info)
Select volume # (change # to corresponding number)
then enter:
attributes volume clear hidden
After that, restart the computer and reassign the drive letter to that volume. And navigate to the path below:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows Search\VolumeInfoCache
Which lists all the current drive info. check if there is any conflict.
Karen Hu
TechNet Community Support

Similar Messages

Secondary SATA hard drive doesn't show up in J115

I've a Lenovo J115 738726u which is installed Windows XP. I installed a secondary SATA hard drive (Western Digital WDBAAX3200ENC-NRSN). The new installed HDD is not shown up as hard disk in file explorer. But In control panel->system->device manager, I'm able to see the new hard disk in the 'Disk Drive'.
Does anyone has idea what's required to solve the problem?
Thanks a lot.

Good day and welcome to the community.
If I'm not mistaken, you'll need to create a partition on the drive before Windows Explorer will see it. You can create a partition from within Disk Management. Right-click My Computer and select Manage from the pop-up.
Hope this helps.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

"F11 System Recovery" during boot does not work after Cloning hard drive.

Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
Startup Menu (F11 System Menu works properly) only on original hard drive.
Following obtained from Disk Management & diskpart in Command Prompt.
GPT Disk <700GB>
Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
Partition 7 NTFS Primary 26MB/350MB [Recovery]
Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
Acronis True Image 2015
Acronis Backup for PC
AOMEI Backupper Professional
Macrium Reflect
Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
“Recovery
Your PC needs to be repaired
A required device isn’t connected or can’t be accessed.
Error code: 0xc0000225
You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
Thank you in advanced.

Hi,
How did you clone the HDD ? One-for-one or different method ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Time Machine does not start after external hard drive is connected

Time Machine does not start after external hard drive is connected

These are the iCloud storage options: http://www.apple.com/icloud/includes/lightbox-storage.html
Also bear in mind that:
1. restoring data over icloud takes time
2. iCloud is not designed as a replacement to Time Machine.

LR 5 does not recognize my external hard drive. It has recognized this drive in the past. No help at any Adobe site.

LR 5 does not recognize my external hard drive. It has recognized this drive in the past. No help at any Adobe site.

My external HD contains photos I have worked on in the past.
Additionally, I have added photos to LR5 directly onto my Mac HD. (38
photos added when working in the absence of my external HD)
Presently, in the Library mode, the Le Cie external HD is not seen in the
upper left hand corner "Source" location.
The only way to "see" the La Cie HD and its photos is in the "Import" mode.
These photos have previously been imported.
I wish to use the La Cie HD as my source in the Library mode and proceed to
the Develop mode.
In other words, work on my previously imported, previously worked on
photos, now on the La Cie.

Windows does not want detect my DVD drive

I do have HP Pavilion dv7-1133cl after uisng Windows Recovery my Windows Vista does not want to recognize DVD drive.
When I have followed all advices what I have read here on chats I have find message:
Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code39)
I do not know what to do with this problem.
I will be really grateful for any help or advice what to do with it.
Regards
Gregory

This is usually caused by a known software issue and happens across the board will all computer manufacturers due to a conflict with media burning/ripping applications...
You can either run this file , go online to Microsoft's site for a fix, or manually fix it by following the instructions below:
Manually delete the registry entries
Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 (http://support.microsoft.com/kb/322756/ ) How to back up and restore the registry in Windows
Note Before you use this method, uninstall all CD or DVD writing or recording programs. Deleting the corrupted registry entries might cause problems with any other CD or DVD writing or recording programs that are installed on your computer. Uninstalling these programs before you start will help you avoid any problems that removing the registry entries might cause. You can reinstall these programs after the problem is resolved.
This method provides step-by-step instructions for how to use Registry Editor to delete the following corrupted Registry entries:
UpperFilters
LowerFilters
Step 1: Start Registry EditorStart Registry Editor
Start Registry Editor...type "regedit" into the run box on the start menu.
Step 2: Delete the UpperFilters registry entry
In Registry Editor, expand My Computer, and then expand HKEY_LOCAL_MACHINE.
Expand SYSTEM, and then expand CurrentControlSet.
Expand Control, and then expand Class.
Under Class, click {4D36E965-E325-11CE-BFC1-08002BE10318}.
In the details pane of Registry Editor, on the right side, click UpperFilters.
Note You may also see an UpperFilters.bak registry entry. You do not have to remove that entry. Click UpperFilters only.
If you see the UpperFilters registry entry in the details pane of Registry Editor, go to step 6.
If you do not see the UpperFilters registry entry, you still might have to remove the LowerFilters registry entry. To do this, go to "Step 3: Delete the LowerFilters registry entry."
On the Edit menu, click Delete.
Click Yes when you receive the following message:Are you sure you want to delete this value?
Step 3: Delete the LowerFilters registry entry
In the details pane of Registry Editor, on the right side, click LowerFilters.
Note You might see a LowerFilters.bak registry entry. You do not have to remove that entry. Click LowerFilters only.
If you do not see the LowerFilters registry entry, unfortunately this content is unable to help you any more. Go to the "Next Steps" section for information about how you can find more solutions or more help on the Microsoft Web site.
On the Edit menu, click Delete.
Click Yes when you receive the following message:Are you sure you want to delete this value?The LowerFilters registry entry is removed.
Exit Registry Editor.
Step 4: Restart your computer
Restart your computer. After you have done this, try to access the CD or DVD drive. If you can access the CD or DVD drive, and if you do not receive an error message, the problem is resolved. You can reinstall your CD or DVD writing or recording software.

Server Essentials R2 does not recognize two new Hard Drives

I have a fresh install of Windows Server Essentials R2. The installation went fine and the Operating System is on a 250 GB SATA Drive. Up to this point everything went well. However, I have added two new 3 TB SATA Internal
Hard Drives that I cannot get the Server Operating System to recognize at all. I want to use these two new HDs as my primary storage for the Client Computers. The BIOS does see the two Drives but the Operating System does not see them, meaning that
no message came up when I installed them from the OS, they don't show up in "Computer" or the "Storage/Computer Management" plug-in of "Administrative Tools". What is happening here? I've tried everything that
I can think of, but with no luck. Please assist with this issue. Thank you.

GPT if i'm not wrong will support large partitions.
I have enabled GPT on my server, and I formatted the drives using NTFS.
check out link below, it's not Microsoft site but it will give you an idea.
text below is from this link: http://www.tomshardware.com/forum/233291-32-what-difference
Here's what the site says:
MBR
is the standard partitioning scheme that's been used on hard disks since the PC first came out. It supports 4 primary partitions per hard drive, and
a maximum partition size of 2TB.
GPT disks are new, and are readable only by Windows Server 2003 SP1, Windows Vista (all versions), and Windows XP x64 Edition.
The GPT disk itself can support a volume up to 2^64 blocks in length. (For 512-byte blocks, this is 9.44 ZB - zettabytes. 1 ZB is 1 billion terabytes). It can also support theoretically unlimited partitions.
Windows restricts these limits further to 256 TB for a single partition (NTFS limit), and 128 partitions.
Only Itanium systems running Windows Server 2003 and Windows Vista systems with an EFI BIOS can boot from a GPT disk. The other operating systems mentioned
earlier can use GPT disks as data disks but not boot disks.
For more information on GPT, see Problems
with larger than 2TB arrays in the General Storage forum, and see Windows
and GPT FAQ for additional information.
Every second counts..make use of it. Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
IT Stuff Quick Bytes

My macbook does not recognize my external hard drive

I have a brand new external drive which I have already formatted in FAT32 and previously used in my MBP with no issues at all. From a couple of days ago though it simply ceased to appear on my Desktop, Finder or Disk Utility. It is, however, recognized in the System Profiler or System Configuration when I click on the USB port tab. No physical damaged has been applied to the HD, and the light turns on normally, making a perfectly normal noise. As I said, it used to run just fine on my MBP, and even on other Mac computers and PC's.
I took it to a store with Apple technical support, they plugged it into one of the store's Macbooks and, surprise surprise, it magically appeared and worked perfectly. They even tried it on a Windows PC and ran just fine. Came back home, turned my computer on, connected it and the problem persists....
Any ideas?... Can you help me?
My specs are:
15'' Macbook Pro 5,1 with an Intel Core 2 Duo 2,4 GHz processor and 8GB of RAM
Mac OS X 10.6.8 fully updated
Western Digital Hard Drive - WE Elements SE Portable WDBPCK0010BBK-01

Did you get a solution for this issue ? I have the same HD which works fine on two other Mac Book pros (Snow leopard and mountain Lion) but does not work on a brand new mac book pro with Mavericks

Bridge does not see both external hard drives

In either CS3 or CS4, Bridge does not recognize my second external hard drive. Photoshop and lightroom see both drives. I am using a laptop and Windows xp.
Thanks,
mIKE

Those directories are modified in the User Preferences tab in the Setup Room.
When you've got the file tree dialogue box open, you'll need to point Color to the "Volumes" level, once there, you should see your external drive.

Putting photos etc into trash does not clear space on hard drive

When I move photos etc into the trash there is no increase in available space on the hard drive.

If you've installed third-party software called "Disk Drill," I suggest you remove it according to the developer's instructions. If you prefer to keep the software, refer to the developer for support. Otherwise, see below.
For information about the Other category in the Storage display, see this support article. If the Storage display seems to be inaccurate, try rebuilding the Spotlight index.
Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash first:
iPhoto ▹ Empty Trash
Do the same in other applications, such as Aperture, that have an internal Trash feature. Then restart the computer. That will temporarily free up some space.
According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation—not the mythical 10%, 15%, or any other percentage. You also need enough space left over to allow for growth of the data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
See this support article for some simple ways to free up storage space.
You can more effectively use a tool such as OmniDiskSweeper (ODS) or GrandPerspective (GP) to explore the volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one. Note that ODS only works with OS X 10.8 or later. If you're running an older OS version, use GP.
Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
Proceed further only if the problem isn't solved by the above steps.
ODS or GP can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
Back up all data now.
If you have more than one user account, make sure you're logged in as an administrator. The administrator account is the one that was created automatically when you first set up the computer.
Install the app you downloaded in the Applications folder as usual. Quit it if it's running.
Triple-click anywhere in the corresponding line of text below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
sudo /Applications/GrandPerspective.app/Contents/MacOS/GrandPerspective
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. You'll be prompted for your login password, which won't be displayed when you type it. Type carefully and then press return. You may get a one-time warning to be careful. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator. Ignore any other messages that appear in the Terminal window.
The application window will open, eventually showing all files in all folders, sorted by size. It may take a few minutes for the app to finish scanning.
I don't recommend that you make a habit of doing this. Don't delete anything as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
When you're done with the app, quit it and also quit Terminal.

Windows 7 Not Starting on Second Hard Drive

Here's some background:
I have a MacBook Pro (15-inch, Mid 2012). My intention is to run OSX on the primary hard drive (750GB Toshiba) and run Windows 7 on the hard drive in the optical bay (500GB Samsung). Through some trial and error and posts I have read on this site, I have determined that it is not possible to install Windows 7 on the secondary drive.
Keeping the latter in mind, I switched the drives, 750GB in optical bay, 500GB in primary bay, and Windows 7 installed and started fine. When I switched the drives back to where I actually wanted them, I got the 'No Bootable Device' error on the Bootcamp drive.
6 Months or so ago, I took the same steps and I was able to boot into both Windows 7 and OSX just fine.
On to my question:
Is this still possible to do or would I be better off adding a Bootcamp partition to my primary (750GB) drive and use the 500GB as exFAT that both Operating Systems can access?

First, you should prevent your MAC to connect to a network. If you are connected with ethernet, unplug the network wire. If you are connected via wifi, switch off your box or apple airport.
Then restore again as you explained, normally, windoxws will not be able to update again, because it will not be able to connect to internet.
Then go to the configuration panel 'windows update'. In the settings, you should be able to desactivate 'automatic update'. Set 'manual update'. This will prevent Windows to redo the problematic update each time.
After that, you should be able to switch on the network again.
Then go in the windows update panel, do 'check for updates'. You should see a list of possible updates, with a box to check or not to do each update. Uncheck the updates you think causing the problem. And do the other updates.
If it works, keep the setting of 'windows update' on 'manual'. Then check regurlarly for updates in a periodic manner (let's say one time each week), and do the updates manually and be carfeul to uncheck the problematic pdates each time.
Also, you should prevent automatic coonection to network. It's more secure. Go in the 'network configuration panel'. Identfy the network you connect to. IN the 'properties', you shoud be able to set 'manual connexion'. Then, each time you boot your Mac on Windows, you will able to connect manually each time you need it, and only if you need it. This is a second security completing the setting 'manual' for updates'. To connect to a network, you have an icon in the task bar of windows, down on the screen, to the right. Do a right click, and you should see a list a networks that can be joined.
I have problems too with recent windows updates. Read this: https://discussions.apple.com/message/20313608#20313608
Maybe the same updates as for me are causing your problems.

How come IMAC does not recognize my Seagate hard drive that I used to use on my PC...I have a lot of documents on this that I need to use

Could you help me, I would like to use my Seagate hard drive that I used on my PC on my IMAC but It does not recognize it and I have a lot of documents I need on this small hard drive....

Please provide more information. Do you mean the drive cannot be seen in Finder or on the Desktop? If it is visible in the Finder sidebar but not the Desktop you just have a setting to correct Finder - Preferences - General Tab and make sure External Disks is checked.

My imac does not recognize an external hard drive

I have bought an USB external drive but my Imac does not recognize it,
the external hard drive does not appear in the desktop neither disk utilities.
characteristics of the disk
toshiba, 1TB, USB 3.0
thanks

The problem is NOT the fact that it is a USB 3.0 drive, as USB 3.0 is backwards compatible with USB 2.0. The problem is specific to Toshiba Canvio portable drives. They only work if you use a micro-USB2 cable instead of the included USB 3.0 cable. This problem does NOT affect other USB 3.0 portable drives (Seagate, Western Digital, etc.), and they work fine with USB 3.0 cables.
Once again, you need a micro-USB2 cable for the Toshiba to mount.

Final Cut Pro Does Not Recognize New External Hard Drive

I am editing a large video project and I had to buy an external hard drive. When I go into FCP, it does not recognize that I now have a lot more room to store media. How do I get it to recognize. Please help! Thanks.

I can see the new disk on my desktop. What do I change in "Preferences" exactly?
In Final Cut pro - System Settings - Shift Q...
You can add it to your list of scratch disks... (which, BTW, should NOT include your system disk)
Patrick

Pismo does not boot after replacing hard drive

We have had an old Pismo for several years now. Two or so years ago we decided to replace the stock 6GB hard drive, which was getting full, with a new 60GB drive. We cloned the old drive via target disk mode, popped in the new drive, copied the data back (again via target disk mode), and were surprised when we were met with the flashing question mark/system folder icon. Sort of left it at that and forgot about it.
I stumbled upon the Pismo again today and decided to see if I couldn't get it working. After going through a few "why won't this even turn on" sessions (the machine hadn't been powered on in a few years, so pulling the internal battery and resetting the PMU fixed that), I popped the old drive back in and the machine booted just fine. Cloned the original drive (again) using Carbon Copy Cloner via target disk mode to a disk image on my MacBook. Powered it down, put the new (60GB) drive back in the Pismo, cloned the disk image back to the new drive. The data's there, because I can browse it in target disk mode, but I can't boot off the new hard drive. I can't boot off my Tiger install DVD either - the DVD drive spins up and tries to access the disc, but won't boot. I'm going to try and get my hands on the CD version of Tiger to see if there's a difference using that.
Disk Utility on the MacBook says there's nothing wrong with the Pismo's hard drive, but I'm not convinced that's the case. I'd heard about Pismos being picky with certain types of hard drives, is this true? If not, what other issues might be leading to this behavior?

Is this perhaps an artifact of the drive being formatted via target disk mode on my MacBook
I suspect that the problem lies somewhere in that situation. I suggest that you boot from the install disk as I suggested previously and reformat the HDD and reinstall the OS.
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• Boot the MacBook Firewire Target Disk Mode.
• Insert install disk into MacBook's optical drive.
• Connect computers via firewire cable
• Option Boot Pismo.
• Select Install Disk for startup and click on the straight arrow.
• Select language
• Go to the Utilities menu (Tiger and later) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• Click on Options button
• Select Apple Partition Map (PPC Macs)
• Click OK
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Apply/Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
Open installer and begin installation process.
cornelius

Windows 8 does not remember secondary SATA hard drive letter

Similar Messages

Maybe you are looking for