Wireless and 7921G Issues.
Hi everone.
I have made a new installation with CUCMBE, a WLC CT5508, AP1262N x 70 and 7921 x 100.
The firmware of the phone is 1.4SE1
We use a SSID only for voice and the APs are maninly used for voice. The currently configuration in de WLC have every frecuency selecte "All", "auto" in 7921, QOS in "premium", WLL "Allowed". Everything else is per default.
I didn't configure QOS in the switches ports connected to APs because I though It wasn't necesary. The porsts are Giga and are coneccted to the core throught 10Gb fiber. May be that was a error.
Now everything is done but we have some issues.
1. We experimente frecuently voice cuts (arround 5 secondos)
2. The phones unregister/register of CM frecuenly.
That happend even when the user are speaking in the same place (a office site per example).
But the main problem was the costumer didn't want give the 7921 phones to the users before the number plan migration so now the system is working in production and the costumer is angry of corse (I alerted him)
Anyway.
I going to change some configuration and I need your advise please. These are the steps.
1. Change the frecuency just work in "b/g" in the WLC and the phone. (is it better "a" to 5Ghz?)
2. Update the 7921G firmware to the 1.4(2)
3. Change the WLL to Requiered.
4. About the QOS in switches. Is that necesary in a WLAN enviromet?
And do you think another option to see/change?
Another thing.
I have seen this post about optimice tha WLAN for voice. He say this.
4. Use 8 channels, configure the Cisco 7921G to only scan those 8 channels. (This is very important)
a. 36,40,44,48,149,153,157,161
http://www.goatnetworking.com/forum/viewtopic.php?f=8&t=15
Someone know where can I configure that at the pohone? do I have to do something to the WLC?
Thank you.
Best Regards
Here is how to set the channels on a 7921G.
1. Enable the web access in CUCM.. (Versions may differ)
You have to set "Web Access*" to Full, then check the box to the right.
Then enter a password in the "Admin Password" field
2. Go to the phones web page https://
- Admin is the username
- Enter the password you entered into CUCM
3. Go to the Profile page, click Advanced in the upper right.
- You then select the channels that you want to use.
Don't forget to save the profile.
You need to set the channels on the wireless network to match the channels that you are scanning on the phone. If the phone is not scanning the channel that you have on an AP, the phone will not see it.
I always trust DSCP instead of COS. COS can be lost going over an access port, but the DSCP will stay with the packet on any switch link.
Similar Messages
-
I have been asked by my boss to add some Cisco 7921 phones to our network.
Currently we dont have wireless coverage.
The wireless will be installed purely for voice.
Can someone advise me on, or point me to some docs, to ensure I set the wireless up as secure as possible, whilst allowing the phones to work, and also to make sure the wireless is configured correctly for voice.Currentlty only looking at one access point, but may expand in the future.
Thanks in advance.Hii leolaohoo ,
I agree with what you said , but even though we support WPA2 , Combination with CCKM was not fully supported.
"Prior to this firmware release 1.3.4, CCKM was not supported when WPA2/AES was selected; this required a full re-authentication when roaming between access points, and could result in loss of audio during the roam. Now that CCKM is supported when WPA2/AES is selected, the full re-authentication is no longer required and roaming to a new access point should not result in any perceptible loss of audio.
Firmware 1.3(4) provides full CCKM support of all WPA versions."
However , in recent firmware 1.3.4 problem seems to be fixed . refer to the following link for details : http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/firmware/1_3_4/english/release/notes/792x_134.html
So in summary :
Use WPA+TKIP+CCKM for firmware 1.3.3 or lesser
Use WPA2+AES+CCKM for firmaware 1.3.4 or later ( you need to verify it that works fine)
Thanks
Vinay -
Hello,
I bought iphone 5 before two weeks from Jordan - Middle East where I live
I noticed that there is a problem with my wlan and cellular connections comparing to my previous iphone 4S
While standing anywhere at home my 4S could see and connect to my home wireless while the iphone 5 could not even see the connection itself !!
So what shall I do with this thing?? is there a problem or the iphone 5 wireless is just weaker than 4S ??
Your help is appreciated
THANKS in advance!Take it back where you bought it.
-
Unbreakable Linux almost installed - wireless and up2date issues
I am trying to build a RAC/linux/iScsi test/play system and I am new to Linux. I have downloaded and installed Unbreakable Linux on 2 dualboot HP laptops with some degree of success.
1. Wireless cards are not working. lspci shows that my broadcom hardware was recognized (but I guess I don't have the driver/packages to support them). Googling leads me to think that I will need to pursue a ndiswrapper solution, or perhaps the kernel just does not support the technology. How do I solve this? Will I need a kernel upgrade?
2. I assume that I'll need patches/updates. The instructions at http://www.oracle.com/technology/tech/linux/htdocs/yum-repository-setup.html describe how to setup and configure up2date and a yum repository. The instructions also say that I'll need to enter an Oracle CSI number when I register and run up2date. I don't have an Oracle CSI# anymore due to a recent layoff. Any suggestions?
3. Should I abandon just Oracle linux and switch to another distribution (i.e. Open Suse or CentOS) ?
Thanks.Hi tom
I am trying to build a RAC/linux/iScsi test/play
system and I am new to Linux. I have downloaded and
installed Unbreakable Linux on 2 dualboot HP laptops
with some degree of success.
1. Wireless cards are not working. lspci shows that
my broadcom hardware was recognized (but I guess I
don't have the driver/packages to support them).
Googling leads me to think that I will need to
pursue a ndiswrapper solution, or perhaps the kernel
just does not support the technology. How do I
solve this? Will I need a kernel upgrade?
First you can install the driver on the wireless card cdrom.if can't ,please list the
type of wireless card.
2. I assume that I'll need patches/updates. The
instructions at
http://www.oracle.com/technology/tech/linux/htdocs/yum
-repository-setup.html describe how to setup and
configure up2date and a yum repository. The
instructions also say that I'll need to enter an
Oracle CSI number when I register and run up2date. I
don't have an Oracle CSI# anymore due to a recent
layoff. Any suggestions?
Unfortunately. if you don't have CSI,you can't run up2date.please go to http://linux.oracle.com and click "Buy Unbreakable Linux from the Oracle Store" label.
Thanks.
3. Should I abandon just Oracle linux and switch to
another distribution (i.e. Open Suse or CentOS) ?
Thanks.It's needless. if you have any question about linux , please .post here. -
Can you help resolve a "Go Wireless" and Verizon Wireless issue?
How do you file a complaint against "Go Wireless" and Verizon wireless? It was partially my mistake because I didn't realize that Go Wireless charges a premium for their service. That said, I was informed by the sales person that I could get the $150 bill credit per phone line I ported over, and a $200 visa card for each smart phone I turned in. That's $350 for each phone in credits.. This seemed like a great deal, so I purchased 3 phones, samsung galaxy 5. I paid a $50 premium per phone to buy them from the store (note..there are NO PRICES listed, you have to rely on what the sales persons quotes you). I also paid a $20 per phone "set up" fee and a $10 sim card fee. Again, I take responsibility for not asking if other verizon stores charged these additional fees. HOWEVER, when I was told to go to the corporate verizon store to get the envelopes for to turn in the smart phones for the $200 per phone credit - this was not my lack of research. I did go to the corporate office and was told that the $200 offer had ended 7 days ago. I went back to "Go Wireless" and the store manager told me that the employee was misinformed and was working off a quote sheet that was out dated. Ok, now you'd think they'd offer something to fix their "mis-informed" employees mistake. No, they said there was nothing they could do. I could return each phone for an additional stocking fee of $35, and cancel my plan. So, here I am...paid a premium for the phones, was "misinformed" by a store agent who was working off an outdated specials sheet, and my only recourse is to pay $105 to return the 3 phones. Something isn't right here. Verizon won't do anything, Go Wireless won't do anything. Any suggestions?
My girlfriend had a similar issue because her new device was not updated to IOS7 when she turned it on, but her backup point was created using IOS7. Check to be sure the restore point was created and then factory reset the phone after you have updated to 7.
-
Wireless and network printing transcript for Meet the Experts
On March 16th, HP hosted its first online chat event on wireless and network printing. Below is a transcript of that session.
I am in the process of planning the next chat event. I would love to hear what topics would interest you, what day of the week and time is best for you, and if you think an hour is too long.
So, if you get a minute, please let me know.
Here's the transcript:
SiobhanF-HP: Welcome! Cameron, Craig, David, and Jim are ready to tackle your questions.
SiobhanF-HP: Just to remind you if you want to ask a question, you must be a member of the HP Support Forums. If you want to join, go here https://passport2.hp.com/hppcf/createuser.do
nc256: Do I need a wireless router to hook up my wireless printer?
CameronL-HP: No, but most people will want to do it this way. You can use a feature called an ad hoc connection to avoid using a router, but it is only covered under an older standard that is slower and less secure. Also, without something to route traffic between the local network and the internet, you cannot get an internet connection. Using a wireless router makes setting up a wireless network easier, and it will generally make the network work better too.
jest1: I've seen some hardware in stores for a "print server" hardware device that attaches to a network. Is this something that I need in order to run a printer over a network?
CraigB--HP: Not if you have a printer that has a network connection built in. Many models of HP computers are ready to be connected directly to your wired or wireless network.
katiepage: How can I print when I am using a VPN?
DavidH-HP: VPN connections generally hide the rest of your home network to increase the security of the VPN connection. A printer on the network isn’t a security threat but the VPN doesn’t know that. It just hides everything just to be sure. That means that when a VPN is active you need some way to connect to the printer other than your home network. Bluetooth, USB, and even printing to a thumb drive and plugging that into the printer are all ways of getting your print job to the printer that don’t go through your home network.
SiobhanF-HP: If you have specific product questions, the more information you give us the better we will be able to help you. Getting your exact model number; any error messages; a description of your wireless network including what kind of security you have, what wireless-devices are connected to your network, and your IP address will go a long way to helping us answer your question.
MelissaP: Why would I want a wireless printer?
CraigB--HP: The main advantage of a wireless printer is the ability to place the printer somewhere in your home or office even if this is not near your router or computer.
Deltan: What is the maximum distance I can have between my router and my printer?
CameronL-HP: It does depend on your environment. Without interference about 25 feet. Walls and floors and other objects can reduce this. The types of walls are important. For example, mirrors and outdoor walls will greatly reduce the indoor range.
jest1: Is there a preferred wireless router type or brand for wireless printing compatibility? We are using a Linksys 802.11g router in my home.
JimB-HP: In general, any wireless-router from a name brand manufacturer that has been Wi-Fi certified is compatible with our printers (look for the Wi-Fi logo). We use Linksys in our lab with great success.
nc256: Are there any digital cameras that can send directly to an HP wireless printer for photo printing?
DavidH-HP: Many printers support a feature called Pictbridge. If the camera and printer both supports this feature, the camera can be plugged directly into the printer to print photos. Or are you asking about printing over a network connection?
KevinW: I keep hearing that you shouldn’t use default settings for a network. Why?
CraigB--HP: There are three reasons not use default settings: First, wireless-routers do not have any wireless security enabled by default. Second, you will be using a common network name in which case you may connect accidentally to your neighbor’s network. Third, your wireless-router is accessible by inadvertent guests who may change the configuration of your wireless-router without your knowledge or use your internet connection without your permission.
Bodie08: I have an HP Lan attached printer and Windows XP on my home network. Is there a known setting (Firewall/port/other) or patch to address the issue of hpqtra08.exe hanging on Windows XP Shutdown? A number of us in the forum have identified this issue. Thanks!
DavidH-HP: This problem has been seen in the past but there were attempts to address it. Have you checked to see if there is a later release of software available on the web? (hp.com)
ZhuLee3: How old is wireless printing technology? I noticed all the experts have around 20 years of experience with it, was there wireless 20 years ago?
JimB-HP: Wireless printing first appeared with the introduction of the 802.11 standard in late 1990's. HP has been making wireless printers since 2003.
lpeterson123: What makes wireless so flaky at times?
CameronL-HP: There are lots of reasons. Wireless signals are affected by distance, walls, metal objects, and other wireless devices like cordless phones. However, most of the problems seem to be from how the network or how security software is configured, and these can also cause things to fail only occasionally or in certain situations. Having a good wireless connection between a PC and printer involves several hardware devices and lots of software made by different companies that all have to work together; if something is not quite right in any of these things then the whole solution looks flaky.
Bowman16: I use a Mac, are there any features that would not work if I was to set it up for wireless use
DavidH-HP: All the features will work on a Mac if you install the full HP software solution.
jest1: Thanks for the answer on the router question. The next question, then, is to ask what would be a recommended consumer-grade wireless-enabled printer (or series) just so I can start my research.
JimB-HP: Any of our Photosmart or Officejet wireless printers will work with Wi-Fi certified wireless-routers. Our price points really have more to do with how much printing you do. In general, our more expensive printers cost less per page than our less expensive models.
Bodie08: Why would I choose "spooling" on my PC over "direct connect”?
CraigB--HP: In general, spooling allows you to use your program sooner than printing directly.
ZhuLee3: Jim: What is it like to be an "HP Printing Expert"? What kind of stuff do you get to work on, on a day to day basis?
JimB-HP: I really like my job -- I've always been a radio enthusiast so working on 802.11 technology is really a dream job for me. I'm also fortunate to work with a great team here in Vancouver, WA. More importantly, I like designing equipment that people use in their everyday lives.
TEACHER1: Recently I changed routers, now I am unable to print wirelessly, even though the SES and wireless network light are steady on my Deskjet 6980 printer. What is the solution? Thanks.
DavidH-HP: The wireless light indicates that the radio is on but does not indicate that the printer is connected to the network. First check that the printer is connected to the network by printing a network configuration page from the printer.
AgentRed: I get my internet with a Verizon wireless broadband card. Someone told me that wouldn't work with a wireless printer. Is that true?
CameronL-HP: Our wireless printers use the 802.11 b, g or n standard which is not compatible with the wireless cellular standard. It would be like trying to connect to a wireless network using Bluetooth. They are different wireless technologies.
DavidH-HP: Regarding the Verizon card, it is true that you cannot connect the printer over the Verizon connection, but as long as your laptop has Wife you can print to the printer over WiFi at the same time that the Verizon connection is active. This should not be a problem.
jest1: Is there a "minimum" internet connection that is recommended for wireless printing? We live a bit far from the DSL CO so our connection is sometimes flaky. I would guess that incoming speed shouldn't affect my local wireless LAN but I want to ask it anyway
CameronL-HP: There are 2 parts to your home network. 1 is your wireless router which manages your local network equipment, then your network connection to the world wide web which your DSL provider gives you. The connection speed of your local network is not affected by your internet connection speed.
Bowman16: Are any HP printers 802.11n? I do not want to add an 802.11b,g to my network and cause it to slow down.
JimB-HP: Currently, our printers comply with the 802.11g standard. We are investigation the emerging 802.11n standard.
ZhuLee3: Will there be a transcript of all the questions and answers from this chat available for viewing after the session? I think I missed some questions at the start.
SiobhanF-HP: The chat event begins when you joined. Sorry that you can't see what was said before you joined. I hope to have transcript posted tomorrow or on Wednesday at the latest.
nc256: Where is the future of printers headed? Does HP have any interesting plans with printing technology? And what’s your opinion on whether or not color laser printing will ever approachthe photo realism of ink jet color?
JimB-HP: The future of HP printing will be characterized by wireless connectivity to not only computers but to mobile internet devices. In fact, as mobile devices become smaller (think phone or netbooks), the need to print from your mobile device might become more relevant.
jest1: Am I able to print from my iphone to a wireless printer?
CraigB--HP: You can print photos from your iPhone to HP wireless printers and it works great in my experience. Go to http://www.hp.com/go/iprintphoto to get the details.
TEACHER1: Thank you. I printed a page. It shows that wireless is disconnected.
DavidH-HP: Then you just need to input the wireless settings from your new router into the printer. If your printer does not let you input the settings from the front panel, you can use the CD that came with the printer or downloaded from hp.com to configure the printer again ( look for the option to "add a device" ).
ZhuLee3: Question about security... if I get a wireless printer, what’s to prevent other people within range of my printer, from adding it and printing documents? How is this configured on the actual printer?
JimB-HP: The simplest way to secure your printer is to enable WPA-PSK security for your wireless network and to use a security pass-phrase that is at least 12 characters long. This configuration is very safe from intruders for the foreseeable future.
CameronL-HP: It' is also a good idea to use a unique network name, also called an SSID.
carolj: I have a photosmart C7180 and I have it hooked up to my laptop (windows vista) when the setup completed the printer was put in networking instead of printers and I cannot access it or move it out of there. What do you suggest?
CraigB--HP: You might need to uninstall and reinstall. Before doing this, make sure your get the latest driver from the HP support at: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=1153754&lc=en&cc=us&dlc=en&lang=en&cc=us This is also where you can get a copy of the instruction book.
wizll: Hi, I haven't done much research in wireless printing, but I'm interested as I currently have my printer set up the old fashioned way where it's connected to a networked PC, but if the PC is off I can no longer print, which is obviously inconvenient. Do hp wireless printers have a web gui you can connect to once it's on the home network, or is it simply all done from the printer's interface. I've seen some old wired network printers that only use the printer's ui and that seems like a clunky use.
DavidH-HP: Yes, the HP printers which have networking built-in have what we call an "embedded" web server which allow you to configure settings, check status, and have many other features; on some models you can even scan using the embedded web server.
nc256: Jim: Will color laser printing ever reach ink jet quality for photos?
JimB-HP: While never is a long time, inkjet printers will, for the near future, output higher quality photos.
katiepage: If I'm at home, connected to my office network via VPN, can I access my office networked printers?
CraigB--HP: Yes, when you are connected to the office VPN, you can print to your office printers. However, you will not be able to print to your home networked printers while you are connected to the VPN.
jest1: If a friend comes over to my house with their laptop and needs to print something, are they able to do this just by authenticating with my wireless LAN (assuming I have a wireless printer set up)?
CraigB--HP: In addition to authenticating to your network, you friend will also need to install the printer driver for your printer.
jpszambelan: Is there a wireless USB device of some kind I can connect to my printer if there is no network connection already built in?
JimB-HP: HP sells an accessory that adds Wi-Fi capability to your USB printer (see http://www.shopping.hp.com/product/printer/inkjet/wireless/4/accessories/Q6236A%2523A2L) Also, many higher-end wireless-routers allows USB printers to be connected to them to allow sharing of the printer from the network. Note that this solution often limits you to just printing and not scanning from the network.
rockwoodchev: It seems that my computer can find my printer, but my printer can't find the computer, so that "Scan to computer" won't work. What do I need to do in order to fix that?
DavidH-HP: This can be blocked by security software running on the PC (such as a personal firewall). Make sure that your firewall is configured to allow communication on your local network. You can also unblock specific ports, but the easiest way is often just to allow communication on the local home network. The specific setting varies from firewall to firewall.
SiobhanF-HP: We are nearing the end of our chat session. We only have time for 3 more questions. If we did not get to your question, please post it on the Networking and Wireless board in the Printers and All-in-Ones forum. http://h30434.www3.hp.com/psg/board?board.id=Networking
SSPatrick: Is it possible to print wirelessly to the same HP printer using both a PC and a Mac?
JimB-HP: Yes -- I do this in my home. I have both Macs and PCs on my network without any trouble.
Bowman16: Any plans to do this again?
SiobhanF-HP: Yes we are.
ZhuLee3: Do all of the experts hang out on the HP community? Will we see you posting there after this?
DavidH-HP: Oh yes, whenever time permits. In addition to trying to help people, I learn things too.
JimB-HP: I'm known as Wi-Fi-Guy on the support forums. I hang out there often helping where I can. It helps me be a better designer.
CraigB--HP: I monitor the forums looking for problems to take back to the development lab for investigation. To date, I have only posted one reply.
CameronL-HP: I haven't been involved in the past but expect to be more involved in the future.
SiobhanF-HP: We only have time for one more question. If we did not get to your question, please post it on the Networking and Wireless board in the Printers and All-in-Ones forum. http://h30434.www3.hp.com/psg/board?board.id=Networking
ZhuLee3: Thanks for setting this up!
SiobhanF-HP: The transcript will be posted on http://h30434.www3.hp.com/psg/board?board.id=Networking
TEACHER1: Thank you all for conducting this session !!!!
jest1: Is there an OS limitation to print wirelessly?
JimB-HP: All the OS versions supported by the printer as supported wirelessly. In general, we are compatible with Macs, Windows and Linux.
SiobhanF-HP: We are ending the chat event. Thank you for coming. We hope you found it worthwhile. I will be posting a transcript of the event in the Networking and Wireless board in the Printers and All-in-Ones forum. We will be hosting future Meet the Experts chat sessions on a variety of topics, so please tell us what you thought of the event and how it could be improved. http://h30434.www3.hp.com/psg/board/message?board.id=Feedback&thread.id=525
Live Forum Closed
Message Edited by timhsu on 03-18-2009 05:39 PM
Message Edited by timhsu on 03-18-2009 05:43 PM
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.I expected this to be released quite earlier. But now that it's in process, I'll wait patiently.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee. -
Failed Hardware Scan and other issues E440
Hi all,
This is probably more rant than anything, but I wanted to give a heads up to others too.
I have a ThinkPad E440 that is a year old. From the very first time I turned it on, there have been issues. The first hardware scan (via Lenovo Solution Center - LSC) showed a warning for the Intel Dual Band Wireless-AC 7260 Local Connection Test. There were also tons of System Events that always show up in the "Configuration History" part of the LSC. You can look at the calendar and tell exactly which days I used the computer because there will be System Events generated each day. Things like app crashes and failed drivers.
In July 2014, I got the first warning for the 16 GB SSD - the SMART Short Self-Test. By February this year it showed as failed for each hardware scan (these were initially set up to run monthly).
Also the whole time I've had it the touch screen would just stop working at some point and I would have to reboot to get it working again.
I finally called Lenovo on March 30th, before my warranty expired. When I called that time, I didn't realize the hard drive failure was the SSD. So they sent me a new 500 GB drive. I also added the other things into the case when I talked to them. For the wireless issue they suggested making sure the driver was up to date. I did this and let them know when I called back that it was up to date and still having the warning. So I called them to tell them to tell them about the wireless and also that I realized it was the SSD having the failure, not the main drive. The first case had already been closed even though none of the other items were addressed.
So they opened another case (this is #2). They said to mail them the laptop since the wireless issue would probably be on the board and it wasn't something I could fix myself. They sent a box with a prepaid overnight shipping label. I was very sick for a few days so I sent it back to them on April 10th (a Friday). Via UPS I saw it was delivered on Saturday. Work was performed on it Monday, April 13th and sent back to me that very day. I received it on April 14th. This part of the service has been excellent - very fast response.
Being in IT, I included a letter with the laptop that outlined the issues that should have been in the case. I also printed the hardware scans and what the system events looked like.
When I got the laptop back, the sheet inside said they had replaced the Speaker because of Distorted Sound. This was not even on the list even though I had noticed it. I didn't even power up the laptop before calling them again - yes, I was furious! Plus our power was out...
So this was noon on the 14th. They opened case #3 and sent me ANOTHER BOX so I could send it back.
After our power came back on the 15th, I powered up my laptop. I opened the browser (I have it set to restore the previous session) and there was a sexually explicit video on YouTube. I opened the other browser and there was a different video on YouTube. So this person was watching YouTube instead of fixing my laptop. I looked through both browser histories and there was quite a bit of activity while my laptop was at the repair center... I ran the hardware scan - still failed and a warning for the wireless. They really hadn't done anything.
I also found two pictures of the repair person in the recycle bin...
So I called back. I was LIVID! They opened another case (this is #4). And sent me ANOTHER BOX. I finally learned the other day that once a case is opened, it cannot be edited or added to at all. Instead, they close the other case and open a new one. I guess their turnaround time for closing cases is excellent! I've never seen a system like that - and I've used a lot of them.
I got a really nice, patient fellow on the line. He took all my info (again). I emailed him the pictures, screen captures of the YouTube videos, the letter I had sent - everything. He entered as much into the new case as he could - he talked to one of the supervisors to make sure he did it right. Somehow he flagged it so that the laptop would get more attention (time) at the repair facility. He also opened a separate case (an escalation ticket?) for a supervisor to call me regarding the person's conduct at the repair facility. He said they would call me that day. (It's now the 25th and I've never heard from anyone)
So, he sent me ANOTHER BOX. I've built up quite a stack of them.
Our power was out AGAIN from the 17th through the 19th (don't get me started).
I noticed a hardware scan had now gotten a failure on the main hard drive. So I called them on the 21st to add this to the case before sending the laptop back. The girl said they can't add anything to an existing case or edit it at all once it's opened. She would have to open a new case and SEND ME ANOTHER BOX. I told her to forget it because I was ready to send it in and didn't want to wait for another box. I also asked for a status on that "escalation case" where the supervisor was supposed to call me. In order to do this she, yes, wait for it, had to open ANOTHER CASE!! So they would know I wanted a status. I'm completely dumbfounded.
So I sent it back on the 21st. This time I practically wiped it. I had already removed all my files the last time, but I had left my bookmarks and browser history intact. I set up a guest logon with admin privileges. I updated my letter and printed off more stuff to include with the box. On one sheet I had only the case number, the serial number and machine type. On another sheet I had "DO NOT SEPARATE THIS PAPERWORK FROM THE LAPTOP" and the case number. I put this sheet on top (The guy on the 15th said my letter and stuff may have gotten separated from the laptop once it was delivered to the repair facility). I used a ton of staples so it would all stay together. I included in my letter the failure on the main hard drive and asked if they could look at it. I wrote about having to open a new case if I wanted to include it.
They received it on the 22nd. A nice gentleman from the repair facility called me that day asking about the password. that. was. written. on the sheet they have you fill out. I told him what happened last time and also mentioned the hard drive failure and asked if he could look into it. He said they would.
I received my laptop back yesterday morning.The sheet that came with it said they had "replaced the following parts to complete the repair of your laptop."
Part Description Symptom
IMAGE Replaced due to engineering change
System board Network card error
Hard disk drive Network card error
ECA-WIRELESS <no symptom listed>
There was also a sheet saying they had installed a factory preload of software and I needed to install Lenovo and Windows updates.
When I booted it up, the first thing I noticed, in the lower right corner was:
Windows 8.1
SecureBoot isn’t configured correctly
Build 9600
I ran a hardware scan. Well, I tried. It stopped part way through and said it finished successfully but most of the tasks showed up as cancelled. I tried to run it again - issues - rebooting ensued. It said the LSC wasn’t available and that I should try again or reboot.
Tried several times. Then got what I guess is the new BSOD - kinder, gentler:
Your PC ran into a problem and needs to restart. We're just
collecting some error info, and then we'll restart for you. (xx% complete)
If you'd like to know more, you can search online later for this error: DRIVER_CORRUPTED_EXPOOL
Even though the LSC said my Lenovo files were all up to date, I ran the Update. And first I had to download a new version of Update. Then I downloaded all of the Lenovo updates and installed them (there were quite a few). The BIOS update failed. While I was doing the Lenovo downloads, I got a light blue screen but no text (I was out of the room so I'm not sure what happened). Did CTRL-ALT-DEL and it shows only IE and Task Manager as applications that are running. Could not “Switch to” IE. Hitting window key to go to start didn't do anything. So I had to restart.
By 3pm yesterday there were 34 system events in the configuration history.
I ran the hardware scan again after I updated the Lenovo files, and you guessed it! Failure on the SSD (SMART Short Self-Test) and warning on the wireless. Nothing had changed. Except hardware scan is acting different than it did before I sent in the laptop for repairs. When it finishes, it instantly closes and just shows 100% complete. When I click on "see last results" it shows a screen called
Log Information,
Canceled 04/24/2015 n:nn pm
You have not done a hardware test on your computer
And the calendar in LSC only shows the very first hardware scan I did on Friday. Even the hardware scan screen shows the date and time of the last scan. It also shows the error code. In order to see exactly what is failing, I have to sit there and watch it very closely and snap a picture of the screen as soon as the error (or warning) shows up.
When I would try to run Windows update, it would hang up PC Settings. I couldn't even kill it using task manager because it didn't show up as a task. During this, I got a flag saying the firewall wasn't turned on. I tried to turn it on, but clicking on Turn on Windows Firewall didn't do anything. I tried to setup my Microsoft account but that just hung too.
I ended up running Windows Update FOUR TIMES to get all the updates installed. Every time I ran it, it said "Done!" and I would run it again and more would show up. The last time was this morning.
At some point, the error about SecureBoot went away.
Then, I created a bootable BIOS update disk. Following the ReadMe instructions, I went through ThinkPad Setup and verified several values. Of note:
Secure Boot was DISABLED. According to the ReadMe file, this should be ENABLED in Windows 8.1. I enabled it.
Under Startup/Boot, according to the ReadMe that came with the BIOS update, UEFI/Legacy Boot is supposed to be set at UEFI Only for Windows 8.1. Mine was set to "Both". I changed it.
In Startup, OS Optimized Defaults was DISABLED, even though it says right there (and in the BIOS update ReadMe) it should be ENABLED to meet Microsoft Windows 8 Certification Requirement.
After these updates, I flashed the new BIOS.
Then, I ran hardware scan again...
Now I have TWO failures on the SSD: Random Seek Test and SMART Short Self-Test. Great.
In the Event Viewer (that I recently discovered), it says my disk has a bad block. It just says The device, \Device\Harddisk\DR1, has a bad block. I assume this is the SSD...
There are 867 events in the event viewer - Critical, Error, and Warning...
Fifty-two of these are from October 7, 2013 - before my little laptop was a glimmer.
The rest are from when Lenovo had it and yesterday and today.
64 of them are the disk error.
341 are from DeviceSetupManager. 65 of those are from failed driver installs. 69 are for not being able to establish a connection to the windows update service. 64 are from not being able to establish a connection to the Windows Metadata and Internet Services (WMIS).
3 times it's rebooted without cleanly shutting down
60 of them are from Service Control Manager and say The TDKLIB service failed to start due to the following error: The system cannot find the file specified.
One of them says {Registry Hive Recovered} Registry hive (file): '\??\C:\Users\Default\NTUSER.DAT' was corrupted and it has been recovered. Some data might have been lost.
16 are warnings that various processors in Group 0 are being limited by system firmware.
12 say the certificate for local system with thumbprint <bunch of hex numbers> is about to expire or already expired.
108 are warnings for failure to load the driver \Driver\WUDFRd for various devices
16 are application errors
One is for the computer rebooting from a "bug check"
15 are for name resolutions timing out after none of the configured DNS servers responded.
10 are for SecureBoot being disabled.
14 for services terminating unexpectedly
15 are for WLAN Extensibility Module has stopped
61 are for applications not being able to be restarted because the application SID does not match Conductor SID
12 are for activation of CLSID timing out waiting for the service wuauserv to stop
So, I'll call them on Monday and open. a. new. case (#5?) - but really 7. And get A NEW BOX.
I'll keep you updated!Hi amycdero and welcome to the HP Forum,
I understand that you are having scanning and printing issues after upgrading to Mavericks OS X v10.9.1. I will try my best to help you resolve this issue.
In this document for Mac OS X: Scanning Software Does Not Open or Stops Responding are steps the may help you with your scanning issue.
This document for Fixing Ink Streaks, Faded Prints, and Other Common Print Quality Problems should help with the streaking printing issue.
I hope this information is helpful. Please let me know.
Thank you,
I worked on behalf of HP. -
IQ826t Restart and Heating Issue
One thing I definitely do not like the HP's support especially when they will not allow us to buy a 7 Upgrade from Vista nor will they support something (even when I find their glitches and they admit after telling me it was just the OS).. On Repair work, I had to ship it out and this will be my 2-3 time to do repair on this PC in the past 3 years (and I have to wait a week for the repair to be done...)
Besides that, IQ826t, Win 7 Ultimate SP1
All Drivers are up to date with HP website (utilizing Win 7 64 bit drivers and Firmware is up to date). AVG update/scan (no issue - confirmed even rootkit).. Malwarebyte - Scan and no issue
Disk Cleanup, Disk Defragmentation done on a monthly and quarterly schedule
Biggest Issue:
I am getting a crash with Win 7 0x124 Stop Error Message (happens periodically and even after a reboot)
Never had this issue until May and the upgrade to Win 7 was done last year with SP1 update done on March (so it is not an issue with the OS as HP support personnel seems to think... I proved them the issue with Windows Update History, The Bluescreen error code on my error code reader).. This machine under warranty and I had issues with it constant (even in Vista)
They state that it is the OS.. Again, if that was the case, I would think it would happen right away like my Toshiba on SP1 upgrade... That was not the case in the matter. I have a firmware reset (default settings) and the issue persist..
The Error Code relates always HAL.dll or ntoskrnl.exe
One if hardware compatiblity and the other is an OS kernel exe file.. And this usually checking knowledge base relates to hardware failing due to 1) Compatibility (which HP website confirms is not the case) 2) OS corruption (which is not the case checking on safe mode and this happening STILL 3) Heat Issue (which I believe is the issue and was been documented on the Internet
What I am noticing is the unit is extremely HOT (vent is almost burning when it has been off and just turned on).. I wonder if the hardware pieces are literally melting to destruction since I can't just open it up (they state it will void my warranty)
The Symptoms before the Crash (happens any time.. Even right after a power up)
If you are playing audio or video, you will start to hear jitters and sound seems to echo itself .. Video would start to lag and become choppy.. Systems start to slow down and things seem to run very slow.. I have seen the power light on the PC start on but the touchscreen just go black (will not restart sometimes)..
Minor Issues (but could be related)
1) When running PC Hardware Diagnostic, they will come up with an error code in the past and that was warranted for a motherboard replacement (of course, they ship the box to the wrong location and I was in the middle of my wedding so I get to it now).. It was pertaining to PCI Express Status ICH9 PCI Express Root Port where it will generate an error code... Now, running the diagnostic... I will not get any error but PCI Express Root Port 3 & 5 do not show up on the diagnostic... Wouldn't that obvious show something that is a problem when there are 6 ports (which on the previous diagnostic that I can't grab past logs shows that). That is not warranted for a warranty work? Just a note, I got the fail test code (which was intermittent but keep happening and the tech support would not look at previous case.. Port 4 failed and a fatal device code)
2) Blu-Ray player will not run and their answer is that it is your Blu-Ray until they realize that I ran it on 3 different Blu-Ray player standalone, different Blu-Ray, and confirm DVD will work.. They still think it is a software issue until they can't deny my point when it will not read the Blu-Ray no matter what (they took control and confirmed it).. They believe the HP SmartDVD software was failing because of Win 7 and not Vista (even when I downgrade and confirm it works, I stated the software is the issue... Lone and behold, 2 months later they had an update that they refuse to admit I was RIGHT on the matter and done 15 hours of troubleshooting that they were wrong about)
3) Wireless Keyboard and Mouse lost connectivity even if the battery is not low... Just stop typing or omit letters.. This is considering the keyboard is literally in front of the touchscreen
4) Touchscreen is sensitive when it wants to be but won't in other... Constant issues there
This is why I have so much issue with support.. They seem to show that they will do anything to deny the issue.. Heck, I am a computer technian calling on the issue.. It ain't like I didn't troubleshoot on the matter... But they think we are all morons and when I prove them wrong, they will use any excuse to honor warranty... That is why it is amazing..Look in your Settings > App Manager.
Tap Device Monitor.
Tap the Battery tab.
At the upper right, tap "Since Last Charge" to change to "Last 48 Hours".
What apps or processes are consuming the most battery power?
ALSO, in setting up your new Z30, are you syncing many contacts or calendar data from a connected email account?
Social accounts such as Facebook or Twitter?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
I am unable to stream Netflix to my Iphone or Apple TV, from my wireless router . . . even though I am able to watch Netflix on my WII (also wireless) and desktop computer (not wireless).
On the Iphone and Apple TV I can connect to Netflix . . . it recognizes me and my account settings . . . and I can veiw all my recent programs and show titles, descriptions, etc.. But when I select one to watch I get a message saying:
"ERROR A PROBLEM OCCURED WHILE PLAYING THIS ITEM. TRY AGAIN LATER, OR SELECT A DIFFERENT ITEM. GO TO WWW.NETFLIX.COM/SUPPORT FOR MORE INFORMATION. (139)
Netflix support say there is nothing wrong on their end . . . that it is an Apple issue. They see the request for the show, the devices are registered . . . but it shows 0 bandwidth to the device.
My Apple TV did this when I first hooked it up a couple of weeks ago. Then after a few days started working with Netflix, for no apparent change . . . now doesn't again for the past couple of days (I think that it auto restarted the other night after a virus scan).
Very frustrating, and driving me nuts! Has anyone else had and been able to resolve this problem?Troubleshooting
Apple TV2 update one day and netflix is browsing but not launching the actual content (error 139)
Ipad2 (another ios device) forces me to update netflix if I want to use it and I get the same error 139 on it.
**** now I have two not ways not working where prior to some update it was fine.
Nintendo Wii is still working ( mind you running an ancient version of netflix ) Dusted the Wii off and gave it to the kids use. Now they are happy again...
PC is also still working ( using some other flash client ) but that's just of interest, we're not going to be watching tv with that.
My wife's iphone 4s is still working. Odd.. still ios but for somereason I am not forced to update the version. So basically she could mirror stream up to the apple tv with it. Nice feature of Ios5. Later found out it is using 1.4 version of netflix. The most useful thing out of that is that all 3 of the devices are Ios and it was actually the iphone with the 1.4 version of netflix that still worked!
I heard from a friend who was on a different ISP he was still working so I took my appletv2 and ipad2 over to my brothers house who is on that same ISP as my friend and both started working. So the ISP is involved too!
Brought the appletv2 and ipad2 back to my house hoping it would maybe still work. No dice Broken again.
Searched the appstore for a decent packet analyzer and there isn't really anything. I was able to sniff the traffic with my PC and also on my juniper ssg5 confirmed that. Turns out port 80 traffic is actually failing and authorization is not happening. The other clients do not do this...
Asked a buddy from work who used to work at the ISP if he could make a call to some one who might actually know what is going on. He came back pretty quick and said yea they are trying really hard to get the beta patch in from Bluecoat asap.
So knowing that it was actually Netflix that changed when it hit 2.0 and in my case the ISP made the adjustment it's pretty safe to say this issue is going to be ongoing unless netflix changes again the way they authorize for licenses.
So that's the summary of what went right down the troubleshooting path but I'll tell what what didn't
2 calls to Netflix (useless... waste of time... they are too quick to blame anyone but themselves)
1 call to apple support (support call was going to cost more than it cost for me to change ISPs)
2 calls to ISP (through the normal means - regular support number)
So why is this intermittantly working sometimes? If you are lucky enough to authorize to an IP address that is not cached they voila you are going to get an authorization / a license to watch the show. Some people report after defribulating their appletv (reseting, rebooting, dns changes, you name it) they get it working. Over the past month we all seem to have got it working for some period of time only to lose it a day to two later.
It's now been several days since the beta patch to the bluecoat and 4 of us who have been communicating on the issue appear to be online all at the same time for those several days and that is a good sign that we might be out of the woods on the issue.
Hope this turns into something helpful for someone else out there. -
The best way to connect wireless and wired for a WRT160N.
It took me about 4 hours to find out how to connect wireless and wired to a network using model WRT160N. Here is what I have done. First install the CD when it says there is not connection connect your PC, Modem and router Andy any wireless are wired products, after that do what the linksys advisor tells your which is default. When it gives you the security key write it down because you will need it for your wireless and wired Products. Under security mode type your SDD name and where key 1 is type your security password with was given to you. Remember all you wireless products have to have the same SDD Like Linsys and all your wired products have to have a different name like Linsys2 but your Key 1 numbers has to stay the same. That is all you have to do. Remember that wireless and wired has to be in sequence. That should do it.
Hi David Hamilton1;
I guess that all depends on how critical your data is in relation to how much time you want to spend doing the erasure. Those higher level erasure options can take a significant amount of time to complete. Personally I don't have anything on my Mac that I think is worth more time then a simple erasure even if that does leave it some what recoverable. To me it seems some people are going overboard on this issue.
Allan -
Cisco wireless and Apple Mac woes
Hello all,
I've been working with Cisco wireless and WLC's for a couple of years now but the recent onslaught of Apple Mac's is giving me heart burn. I've seen this at numerous sites now and need to throw it to eht community for guidance.
Basically we have had a number of instances where the Macs just fall off the wifi. Sometimes it's when they wake from sleep and other times when roaming between AP's (1131s with same SSID's). Our standard install is WPA2 and per ap local authentication. PC's work fine and never an issue.
We have completed a survey with a spectrum analyser and no RF interefence is present nor errors on the radio interface.
Questions:
- Is there a preferred Cisco config/setup for Mac's to work reliably? I've heard loads of rumors but nothing concrete and nor can I find anything specific.
- Should I be setting up WDS in case there is an authenticating issue.
- For those who are Mac gurus and happen to be reading. What Mac options we should look at?
This has all come to a head because the clients IT company who recommended the Macs (different from us doing the network infrastructure) are insisting that the problem is Cisco incompatibility and that we should rip out the Cisco kit and install airports (what tha!!!).
Thanks in advance for any pointers.
For those who like a config here it is .... Vanilla stuff really
Building configuration...
Current configuration : 2236 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP4
no logging console
enable secret xxxxxxxxxxxxxxxxx
no aaa new-model
dot11 syslog
dot11 ssid Home
vlan 1
authentication open
authentication key-management wpa
guest-mode
mbssid guest-mode
wpa-psk ascii xxxxxxxxxxxx
dot11 ssid avnet
vlan 2
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii xxxxxxxxxxxxxxxx
username abcd password 1234
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
encryption vlan 2 mode ciphers tkip
ssid Home
mbssid
speed basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.10.54 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
no ip http server
no ip http secure-server
bridge 1 route ip
line con 0
line vty 0 4
login local
endYeah!! even i have come across multiple issue with MAC and Cisco.. these are the below settings which i normally do on the cisco gears and most of the times this solved the issue..
on the IOS AP disable Aironet Extentions and set the poer local and ofdm to max
no dot11 extension aironet
power local cck max
power local ofdm max
end
On the WLC, disable Aironet IE..
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull -
I was decieved by Verizon Wireless and I may have to tell the world!
I too was decieved by Verizon Wireless and have had to pay for a phone we never intended to use for a year now. All they said was, did I agree to the legal mumbo jumbo, which of course I had to or I wouln't have been able to finish the contraction I thought I was signing up for. I've complianed about this every time I've spoken to verizon wireless since then for a year, but they don't care. All they care about is, are they getting more money from me. Well, yes they are, but I am a very unhappy customer and they will soon see how unhappy I actually am. I'm a jounalist and a publisher. And I'm going to take aim at them with the written word if they do not come to their senses and understand that a happy customer is more important than taking money from a customer based on a mis-understanding. Are they legally ok with this? Yes. Are they right about this? N. O. spells no!
If they check the history of the phone in question, which I have brought up with them numerous times, they will see that we indeed have not used it for almost a year now. THEY ARE WRONG IN DOING THIS TO ME AND MY FAMILY. THEY ARE STEALING. ARE THEY LEGALLY COVERED? YES. ARE THEY RIGHT. NO!!!!!
VERIZON WIRELESS. DO THE RIGHT THING AND MAKE GOOD WITH ME.
I am a publisher and I have a blog that has a thousand
unique visitors per week. I've put together a paper that has 145 complaints
that Verizon wireless customers have given me permission to put in the paper as
examples of problems with this company.
I am giving Verizon wireless a chance to make things right
with me before I post the work on my blog. I will also give Verizon wireless a
chance to make good with me on my issue before I publish the work on Amazon's
Kindle and B&N's Nook for customers throughout the world to have FREE
access to download.
VERIZON, DO THE RIGHT THING AND MAKE GOOD WITH ME!!! TIME IS
RUNNING OUT!
You have my information, call me and we can straighten this out.
Please! Pretty Please with sugar on top!!
As for anyone who thinks I'm trying to wriggle out of making a mistake. You are wrong and are commiting libel, since you don't have the facts. THIS IS BETWEEN VERIZON WIRELESS AND ME!
>Add'l info from another new post by the poster has been added to their original post and their latest posts have been deleted. In addition editing occurred to comply with the VZW ToS<
Message was edited by: Verizon Moderatorcommonsense101 wrote:
you added a line of service because you cant afford to buy a phone.. and then expect verizon to forgive the contact
is that what i'm understanding here?
That is exactly how I take it, but it seems some important info is missing. -
Windows 7 Wireless and Audio Drivers on 2010 MacBook Pro
I have a new MacBook Pro i7 2.66 Mhz with Snow Leopard and dual boot to Windows 7 64 bit Ultimate. I can't find the correct drivers (Windows 7 side) to get the audio and the wireless networking operating. I ran the bootcamp setup from the Snow Leopard install disc on Windows 7. It gave an error message that this model is not supported. I then ran each software driver individually from the install disc and was able to get all to work except the audio and wireless. I then installed the Bootcamp 3.2 update from the Internet with no improvement.
Does anybody know where the audio and wireless drivers can be located for Windows 7? (Apple Support has not been able to resolve the problem yet) Thank You!I'm having the same problem with Windows 7 64-bit Professional. I had to go through the same process to get most of the drivers installed. I've had the same issues with the wireless and audio drivers.
To get the Apple drivers installed, I followed the instructions from this blog post.
http://michael.anastasiou.me/index.php?option=com_content&view=article&id=22:qbo ot-camp-x64-is-unsupported-on-this-computer-modelq-solution&catid=7:how-to&lang= en
Has anyone had any luck with the rest of the drivers? -
Hi Everyone,
My phone takes too long to send SMS (2 - 3min), my gallery freezes when you revert back to it after editing a picture and the ringtones play when my phone rings, but seconds later it slows down like a broken record!
I have perform the *-3-Green reset, I have had the software updated and the issue is unresolved.
I dont think Nokia knows what to do now except for reloading the firmware. (Theey have reloaded it a total 9 times since I got the phone in July 2006)
Can anyone shine some light, apart from going to another brand?
My carrier is Vadofone AU.
Cheers.
Nokia N80 Pearl Black | v4.0623.0.41 | RM-92 | 68.01
Sydney, Australiain the application manager section of the Nokia N80 handset, is there anything that can be removed which may be causing slowness??
i just looked and i have the following in the application manager section, what can i safely remove?
QUICKOFFICE
CATALOGS
WIRELESS KEYBOARD
SEARCH-LOCALPLUGINS - HK
SEARCH LOCALPLUGINS - IT
SEARCH LOCALPLUGINS - FI
SEARCH LOCALPLUGINS - SE
SEARCH LOCALPLUGINS - UK
SEARCH LOCALPLUGINS - DK
SEARCH LOCALPLUGINS - FR
SEARCH LOCALPLUGINS - ES
SEARCH LOCALPLUGINS - NO
SETTING WIZARD
ADOBE READER LE
SEARCH-GLOBAL PLUGINS
SEARCH
SEARCH -
Major Wifi issues and 3G issues
Hi,
Let me start off by saying I have been searching for 3 days for help and can find nothing so here goes.
My iPhone 4 will connect to my wifi at home but will not open any webpages. I also have a 3G and a 3GS which work perfectly fine on the network.
I have made sure my router firmware is up to date and have renewed the lease on the phone and tried again, it seems to work for about 2 minutes and then stops, although the wifi icon stil displays at the top.
Second moan is that I NEVER get over 2 bars in 3G unless I go into the Orange shop to moan about it.
Again my 3g, 3gs are both on Orange and they are full with 3G but my Iphone4 dithers at around 1 or two bars at the most... what can i do to improve it?
On a positive note, my free bumper case was delivered this morningI have since reset the firmware on my existing router after reading that there may be compatibility issues with newer iPhones/OSs and older routers .. I also checked router wireless and network settings against Apple recommended settings on http://support.apple.com/kb/HT4199?viewlocale=en_US .. So far, situation appears improved. Let's see if that persists.
Maybe you are looking for
-
AP Payment to Generl Ledger (11i)
Dear All, if I know the payment number and the payment has been transfered to general ledger, How can I get the journal batch name and journal name of the payment journal? Could someone comment? Thanks & Best Regards, Jerome
-
'This device already associated with an Apple ID'
Hope someone can help with this. One of my students needed to download a recorded homework assignment that she'd saved to iTunes - I let her log into my iPad to do this, not thinking it would be a problem, but now I can't access any of my Music! I ge
-
I rented four movies on my mac and then transfered them to my iPad, i then did an update to my iPad, now the rentals are not on my ipad nor my mac. I did not watch them and I was charged for them. How do find them and transfer back on my iPad
-
I've noticed that the clock on my Macbook pro disappears after 23:59 hours (currently running OSX mavericks latest update) - This happens repeatedly. Is this a known bug? Has anyone noticed this or is this happening to you?
-
Hello How to define Input tax code for I/P ED 5.15% & CST2% regards