Wireless guest access with CWA and ISE using mobility anchor
My team is trying to demo wireless guest access using CWA with an ISE server. We appear to be hitting an issue when combining this with mobility anchoring.
When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound. The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.
FOREIGN
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 255,
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP requested ip: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP ciaddr: 0.0.0.0, yiaddr: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP siaddr: 10.30.4.173, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP server id: 1.1.1.2 rcvd server id: 1.1.1.2
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is 1
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 3600 seconds
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
Similar Messages
-
Hi support community
we just implemented CWA for wireless guest access using ISE. however we have an issue, the redirect URL is a name, not an IP address, and the guest dhcp scope use public DNS servers, so CWA doesn't work unless we set the company DNS servers.
so my question... is there a way to configure ISE to send the ip address instead the name for redirection in CWA?
Many thanks in advance...Hi, thanks for answering...
Yes the problem is that public DNS servers obiously can't resolve ISE servers names. Additionaly the guest VLAN has an ACL blocking all the traffic destined to internal resourses with some exceptions (DHCP, DNS and ISE port for CWA).
however, guest can access to some company services, but as if they were located on internet, ie through the public ip address, so if we use internal servers, they resolve the internal ip address and connections fails. the Muhammad suggestions could be the solution for the problem....but now is something to discuss with the DNS server administrator...
thanks -
Wireless Guest Access with 802.1X (PEAP/MSCHAPv2) and ISE?
Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. LarsenHi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen -
Wireless guest access with Airspace
I understand the Airspace products have some guest access capability built into them. I have a hotel customer that has the following requirments.
First, he will have an AP in each conference room. He would have each AP set up with a different SSID. The guest username password used for logging in would be assigned to the SSID and be different for each conference room. I've been told this is not possible. While you can have more than one guest username/password they are not associated with any one AP or SSID.
Secondly, he would also like to be able to control the amount of bandwidth each conference room/group is assigned.
Can the Airspace stuff do this, or even something close to it?Yeah - no.
The Airespace guest functionality is basic - you define an SSID which has 'WEb Auth' set on it, and users are prompted for a username/password that is auth'd against radius.
The sort of granular stuff you are looking for isn't there - maybe look at BBSM or something similar, although I don't know how well that interfaces with AireSpace if at all..
Regards
Aaron
Please rate helpful posts. -
1801W wireless (guest access) config issues
Trying to setup wireless on 1801w ISR. Wired access to Internet and LAN works fine (Vlan1); however, wireless (Vlan2) does not.
Trying to setup wireless "guest" access with Internet access only (no access to LAN).
Wireless will not come up. Dot11Radios show "reset/down".
Below is the wireless config and a couple of troubleshooting commands as well:
dot11 ssid open
vlan 2
authentication open
====================================================
!(Sets up DHCP and excluded addresses.)
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 172.16.25.1 172.16.25.99
ip dhcp excluded-address 172.16.25.116 172.16.25.255
ip dhcp pool open
import all
network 172.16.25.0 255.255.255.0
default-router 172.16.25.1
dns-server 4.2.2.1 4.2.2.1
lease 3
====================================================
(Turned on integrated routing and bridging.)
bridge irb
====================================================
(Wireless radio interface config.)
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip virtual-reassembly
ip route-cache flow
encryption vlan 2 mode wep optional
!---(SSID is given as "open")
ssid open
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
description LAN
ip address 192.168.0.100 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Vlan2
description Wireless VLAN
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 172.16.25.1 255.255.255.0
ip nat inside
ip virtual-reassembly
bridge 1 protocol ieee
bridge 1 route ip
====================================================
Verifying...
RTR#sho dot11 associations
802.11 Client Stations on Dot11Radio1:
802.11 Client Stations on Dot11Radio0:
SSID [open] : DISABLED, not associated with a configured VLAN
====================================================
RTR#sho ip int brief
Dot11Radio0 unassigned YES NVRAM reset down
Dot11Radio0.1 unassigned YES unset reset down
Dot11Radio1 unassigned YES NVRAM reset downYour ssid is configured in vlan 2.
But you forgot to configure dot11radio0.2 with under it "encapsulation dot1q 2".
That should allow the radio to broadcast ssid
Nicolas
===
Don't forget to rate answers that you find useful -
LWA Guest Access with ISE and WLC
Hi guys,
Our Company try to implement Guest Access with ISE dan WLC with Local Web Auth Method. But there is problem that comes up with the certificate. This is the scenario :
1. Guests try to connect wifi with SSID Guest
2. Once it connect, guests open the browser and try to open a webpage (example: cisco.com)
3. Because, guests didn't login, so it redirect to "ISE Guest Login Page" (url became :
https://ise-hostname:8443/guestportal/Login.action?switch_url=https://1.1.1.1/login.html&wlan=Guest&redirect=www.cisco.com/
4. If there is no ISE Guest Login Page installed, message Untrusted Connection message will appear, but it will be fine if they "Add Exception and install the certificate"
5. After that the Guest Login Page will appear, and guests input their username and password.
6. Login success and they will be redirected to www.cisco.com and there is pop up from 1.1.1.1 (WLC Virtual Interface IP) with logout button.
The problem happen in scenario 6, after login success, the webpage with ISE IP address and message certificate error for 1.1.1.1 is appear.
I know it happened when guests didn't have the WLC Login Page Certificate...
My Question is, is there a way to tunneling WLC Certificate on ISE ? Or what can we do to make ISE validate WLC Certificate, so guests doesn't need to install WLC Certificate/ Root Certificate before connect to Wifi ?
Thx 4 your answer and sorry for my bad English....Thx for your reply Peter, your solution is right,
i don't choose CWA, because their DNS is not stable...
i've found the problem...
the third-party CA is revoked, so there is no way it will success until it fixed...
and there is no guarantee, they will fix it soon..
so solution that we choose is by disable "HTTPS" on WLC...
"config network web-auth secureweb disable".
"config network web-auth secureweb disable".
"config network web-auth secureweb disable".
"config network web-auth secureweb disable".
"config network web-auth secureweb disable"
thank you all... -
Hi Guys, I have a wireless requirement from a customer and the customer is looking for the below: 1. Wireless guest access that requires user to input email into the captive portal. But the email address must be verified that it contains certain selected domain names (e.g. example.com or example.org). Any other domain names will be rejected. 2. Customer is looking to add their own logo and change the formatting of the captive portal. Questions: 1. For email verification, does this feature come straight from the WLC standalone box or must ISE be purchased? 2. If the WLC is able to do this without ISE, any online guides that is able to do this? 3. For security reasons, am I able to limit the number of concurrent users using this captive portal? 4. How do a configure the age-out for each connected users after they have successfully logged into the captive portal? 5. Can I customize the captive portal page on the WLC and how do I go about doing it?
Hi Mohanak,
It looks like the formatting ran out. Anyway, not sure if we are on the right topic here but let me get this straight. Customer has a Cisco 2504 Wireless LAN Controller. So, they would like to achieve the below features:
1. Wireless guest access that requires user to input email into the captive portal. But the email address must be verified that it contains certain selected domain names (e.g. example.com or example.org). Any other domain names will be rejected.
2. Customer is looking to add their own logo and change the formatting of the captive portal.
So, some of the questions I have are:
Questions:
1. There is a configuration on the WLC that allows guest users to login using email verification only. Does this feature come straight from the WLC standalone box or must ISE be purchased.
2. If the WLC is able to do this without ISE, is the WLC able to check if the inputted field is a valid email? And can I configure in such a way a particular domain is allowed? (e.g. example.com is permitted but example.org and anything else is reject).
3. For security reasons, am I able to limit the number of concurrent users using this captive portal?
4. How do a configure the age-out for each connected users after they have successfully logged into the captive portal?
5. Can I customize the captive portal page on the WLC and how do I go about doing it? -
Hi
I have setup wireless guest access for a customer with a single 5508 and web authentication no problem at all. He then wanted to test wired guest access. The 5508 is currently connected to a single 3560 switch. The wired clients get a DHCP address OK but cannot reslove DNS and thus don't get redirected to teh guest login portal. I have even tried turning of all L3 security to no avail. The setup is as follows
VLAN 101 access points and 5508 management interface
VLAN 102 wired guest access dynamic ingress (L2 config only no SVI on 3560)
VLAN 103 wireless guest dynamic egress nterface L3 network with SVI on switch
VLAN 104 wired guest dynamic egress interface L3 network with SVI on switch
There are two DHCP pools setup on the WLC one for the VLAN 103 and one for the VLAN 104 subnets.
The internet router is also connected to the 3560 on a sepearte VLAN with an SVI. the 3560 has a default route to teh internet router and teh DHCP pools give the DHCP clients a default gateway of the IP address of dynamic interface 103 or 104. The Internet routre can ping the WLC on both these addresses.
LAG is enabled on teh WLC and VLANs 101-104 are trunked to it from the 3560.
I even tried making the wired guest egress interface the same one as for wireless. The wired clientys now got an IP address on the wireless range but still couldnt pass any traffic. It's like the intrenal bridging on teh WLC between VALN 102 and 104 (or 103) is broken. Tried both the lates 6.x and 7.x software on the WLC. Any ideas ? All the problems I can find with this seem to relate to not gettingas far as a DHCP address but that works fine.
Thanks
PatHi
Yes got it resolved. It turns out that the connection from the wired guest access port to the WLC must be L2. That is the switch that the wired guest acces sport is connected and WLC are connected to must be L2 only. We were using a single switch to do the testing and it was also doing the routing for the test LAN. Even though there was no L3 VLAN interface configured for the VLAN that the guest access port was on for some reason this breaks it. Absolu Didnt have chance to work out the exact limitations of this as we simply made the switch L2 only and configured an 802.1Q trunk to the Internet router and made subinterfaces on the router for the wired and wireless egress ports and it worked then. No config change was needed on the WLC at all.
The only thing I can think of is that it's something about the way the WLC joins the wired guest access ingress VLAn and egress VLAN. The WLC isn't a reall router it says so in the documentation. I think the packet coming from the wired access port is being bridged to the egress VLAn not routed and this is what screws it up (remeber with a router the source and destination MAC addresses would be changed with a bridge they aren't). Got to be something along those lines. If you have a bigger newtork with a guest anchor WLC handling this function you dont run into this as the traffic is coming over an EOIP tunnle from the remote WLC so the switch with the guest anchor WLC doesnt see the MAC address of the wired guest PC. -
Hi I need help in configuring unified wireless guest access. i have followed the guide
http://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob41dg/ch10GuAc.html#wp999843.
But the problem is it still does not work. what i dont get is that the interface for the Guest SSID for the foreign controller is management, does this mean that i have to get an IP address first from the management segment before i can get an IP from the anchor WLC?
my setup is that i have an anchor controller which is on a different LAN from where my foreign WLC is. the anchor WLC has the DHCP scope and the local net user database. I have already join the two WLC to each other's mobility group. also i have configured the mobility anchor on the WLAN(SSID) of the foreign controller.
Another thing is that the AP im trying to use is on a different site from where my controller is. Im not sure if this is the one causing problem.
Can someone help point out my mistake.Its rare that I have a difference in opinion from both of you guys but let me share with you an issue I had.
If you map the foreign controller to the management interface and the tunnel breaks for whatever reason the clients will get dumped on the management interface, even though the WLAN is anchored to the DMZ controller.
I know this becuase I seen this for my self when I had anchor issues.
I opened a tac case and it was suggested to use a "dummy interface" on the foreign controller. I forget who I spoke to, this is over a year now. But I then followed up witha Cisco SE on the Advance Wireless team and he commented this is what they do as well. And to add further, a large hospital system here in the Tex Med center had Cisco advance team install their controllers and they too had dummy interfaces for the foreign controllers for guest.
Just my 2 cents ... Add a dummy interface call he dummy_guest_interface and tie it to 222.222.222.222 or something like ... no need to add anything on the wired. -
Does WAP4410N support Wireless Guest access solution?
Does the Linksys AP (WAP4410N) support Wireless Guest access solution?
Hi - I've got a WAP4410N which I'd like to use to provide wireless guest access, and I've had a look through the configuration pages and manual, and understand:
1) I've got to add a virtual SSID (although I'd like to know where the DHCP settings are as I don't believe the WAP4410N has DHCP capabilities)
2) I need to ensure that traffic can't hop across the multiple SSIDs
What I'd like to know is whether the WAP4410N can be set up to display a terms and conditions page which users have to "OK" or whether it can host a login page that can be administered by someone to allow access - kind of like hotels use to ensure that not everyone can automatically connect? I don't mind if there has to be a secondary piece of software hosted on a server someone, but I'd like to prevent people from being able to automatically connect straight to our connection and would also like to limit them in some way, at very least the bandwidth that the connection allows, at best the sites they can visit too.
Any thoughts greatly appreciated,
Andy -
E4200 Wireless Guest Access issue
Hello, I'm hoping someone can point me in the right direction. I have the wireless guest access set up in my E4200 flash to the latest firmware.
When I connect to the wireless guest network it comes up under the 192.168.33.xx IP address. I can connect fine but it never pops up the browser so that you can type in the guest password. I'm running Windows 7 but I've also noticed the exact same problem under XP.
The only thing I can guess is the problem is that I have this acting like an access point and all DHCP requests go to my router. I've basically turned off DHCP on this and plugged the network connection into the switch on the back.
Any suggestions?
Thanks
JoshIf I go to 192.168.33.1 it does pop up the browser but when I enter the password It just hangs. Not sure if it was connected or not. Is there no way to pop up the browser automatically?
-
I had an iphone 4s and it worked nice with facetime and imessage using my phone number but it was stolen on December so I buy a new iphone 4s using the same cellphone number but now imessage and facetime does not work with my number, it only works with my apple ID. Please Help me I speak Spanish so if my English is not ok I´m sorry about it.
Do you think that apple has to reset in their database of the old serial number attached with my phone number and that’s why I can´t activate imessage and facetime with my number in the new iphone 4s??I understand all of this Meg; that is why I bought an Iphone; but never expected my phone not even give a at least a 24 or even 12 hours....I work 12 hour shifts and also would expect to have to charge each night but not twice a day or more. I am not always somewhere I can charge my phone.
Your points are true; however it doesn't help me...... -
I had a gift card with money and I used it on iTunes now there isnt any money...
I had a gift card with money and I used it on iTunes now there isnt any money how to i change my payment back to none? When I try downloading any app it say "Please enter password to review billing information" I want to change it back to "none"
Sign into your account through the iTunes app and look for a None option in the Payment Method section.
-
How to send Email with Cc and Bcc using MailPackage
Hi ,
we are using Mail Package to send the Email using Mail Adapter.We have a requirement where we need to send Email with Cc and Bcc using Mail Package .
Can we send Cc and Bcc using Mail Package ?
Thanks
Rajesh .HI Rajesh,
There is a standard structure for Receiver Mail adopter which we can get from SAP market Place but it is not provided with CC if u want to use CC then you have to go with Dynamic Configuration.
DynamicConfiguration configuration = (DynamicConfiguration) container.getTransformationParameters().getStreamTransformationConstants.DYNAMIC_CONFIGURATION);
/*any other required fields*/
DynamicConfigurationKey key = DynamicConfigurationKey.create("http://sap.com/xi/XI/System/Mail", "THeaderCC");
configuration.put(key, "ccemail @ test.com");
Regards
Praveen Reddy
Edited by: Maareddy Praveen Reddy on Aug 10, 2011 12:17 PM -
Very happy with IMac version 10.4.11 Paired a wireless Bluetooth headset with the intention of using it to listen to radio podcasts. However, cannot connect headset. Any suggestions??
Perhaps this "hint" might resolve your problem:
http://hints.macworld.com/article.php?story=20050520082617274
Maybe you are looking for
-
I ran the update. i lost my "tools bookmarks file ect. how do i get them back
I ran the update to i think 3.6 Before the update i had the words " file view etc across the top. now they are gone how do iget them back?
-
FM for read cost center distribution infotype 1018
Hi Gurus, Can anybody provide FM for read OM Infotype 1018 - cost center distribution. Note : Requirement is get cost centers which are maintained in 1018 as POSITION based. Regards, Ranjith
-
Firefox 4 map search not working
When I open the maps search on firefox 4 homepage and enter a location, firefox says loading but goes no further, I can access the map of a location from the web search box by entering map followed by the location name. How can I get the map search t
-
Doesn't do it with other search engines Have tried to fix but no success
-
Unable to deploy artifacts to SOA MDS
Hi, When I try to deploy common artifacts to MDS through JDeveloper using procedure explained in this blog: http://yatanveersingh.blogspot.com/2011/07/mds-implementation-in-oracle-soa-11g.html , or try to do same thing using ant script as explained h