"Wirless Client List" button on WRT160NV3

Has anyone had any joy getting the Wireless -> Wireless Mac Filter -> Wireless Client List  button to work?
I've tried several browsers, and several versions of the firmware (v3.0.02 and v3.0.03) but no joy.
In each case my browser pops open a new empty window and then it appears the webserver running on the WRT160N crashes.  It no longer accepts any more connections on port 80, although continues to operate fine as a wifi router.  I need to powercycle it to get the management web interface working again.
And yes, I did the full "reset-to-factory defaults + reload my configuration" dance after the firmware upgrade.

Whenever you upgrade the firmware on your Router, you don't need to load the configuration on your Router, you need to configure all the settings on your Router from scratch.

Similar Messages

  • WRT160Nv3 - Clicking "wireless client list" button kills WRT160Nv3 web interface.

    Clicking the "Wireless Client List" button on the "Wireless MAC Filter" page causes a new Internet Explorer instance pop-up containing the the error: "Internet Exploer cannot display the webpage".
    After the error appears, I can no longer access the WRT160Nv3 via it's web page interface. I just keep getting the above error message. But I can bring up a command prompt and sucessfully PING the WRT160Nv3. I just can't get back to the WRT160Nv3 router's web interface.
    If I wait about 24 hours (or so) the WRT160Nv3 web interface is accessable again.
    Why is this happening, how do I correct it and how do I get a list of all the wireless devices connected to my WRT16Nv3 router?
    Thank you.

    Okay, I'll assume the solution of resetting (and then recofiguring) the WRT160Nv3 router gets the router's web interface working again.
    But how do I see which of my client devices are actually connected to the WRT160Nv3?
    Clicking the "wireless client list" button appears to causes a problem for the router's web interface and then requires resetting and reconfiguring the router.
    It seems like I still don't have a solution that shows me which devices are connected to the router. And I have to reset and reconfigure the router if I attempt to invistigate which devices are connected to the router.
    Any additional insight would be appreciated.
    Thank you;

  • E1200 Wireless Client List will not display and causes web UI to temporarily stop responding

    I picked up an E1200 and set it up successfully.  I am using wireless MAC filtering, and decided to pull up the list of connected wireless clients (Wireless >> Wireless MAC Filter >> push "Wireless Client List" button).
    When I do so, it immediately throws this back:
    Immediately after this the Web UI of the E1200 becomes inaccessible.  It still routes traffic, and the router remains pingable, but it will not allow access to the Web UI for several minutes.  The error that appears upon attempt to access the Web UI during this time window is similar to the above, but reads "Error 102 (net::ERR_CONNECTION_REFUSED): The server refused the connection."
    I have tried this in Google Chrome, Firefox 4, and MSIE on two separate computers.  Each browser displays the error a bit differently (MSIE, for example, just says it can't display the page and gives no further detail) but the net results are always the same.  I have tried resetting the device to factory defaults in addition to re-downloading the firmware from the Cisco/Linksys website and installing it.  No improvement.
    I have also noted that the Log (Administration >> Log; and yes, I have it enabled) doesn't appear to be picking up anything at all.  In fact, the Security log, which supposedly (according to the Help) "displays the login information for the Router’s browser-based utility," is also blank.
    Is this a bug, or should I head back to the retailer and swap this device?

    Ok - I nailed this down, I think, and it looks like a firmware bug.
    Short version is that a factory reset cleared the issue, but during stepwise reconfiguration the problem came back.  Through a bunch of iteration I figured out that if I have the E1200's DHCP server disabled *and* have wireless clients connected to it, the problem I described appears.
    Turn the DHCP server back on and the problem goes away.  Turn it off and the problem comes back.  Turn it back on and it goes away.  You get the idea.
    If I had to pose a theory here, it's that the initial display of the Wireless Client List, which uses "IP Address" as the default sort, somehow implodes if the E1200 isn't actually assigning those IP addresses to the clients.
    When this happens it appears to crash the Web UI wholesale.  Just for grins, while the Web UI was unresponsive, I pinged the router it as before - still pingable - then ran nmap against it - no open ports found on the router.  When the Web UI is functional, though, nmap detects port 80 quite easily.  I have not timed how long it takes for the Web UI to come back up, but it is longer than 5 minutes, and I presume some sort of watchdog process has to detect that it has gone kaput and start it up again.
    Final test was to restore my saved configuration from before the factory reset (note that the saved config was done under the same firmware version, and in this config, the DHCP server is disabled).  Boom, problem.  Wait for the Web UI to come back, turn on the DHCP server.  Problem goes away.  Turn the DHCP server off.  Boom, problem comes back.
    So, there you go.
    Would be interesting if someone could verify this via a test against another E1200.  It may be worth noting that in my baseline test I was also using Manual wireless setup (vs. Wi-Fi Protected Setup), and WPA2.  Didn't make any other setting changes from the factory defaults.  I did not actually have to turn the Wireless MAC Filter on to do the test.  All one needs to do is click Enable on the Wireless MAC Filter tab, and then do *not* click Save Settings - just clicking Enable will light up the Wireless Client List button, which you can then push to get the list.  That is how I handled testing to ensure that neither specific entries, nor the Prevent/Permit setting, nor having the filter enabled in saved configuration were involved in the problem.
    Separately, no explanation for the lack of entries in the security log, but that pretty much looks like a firmware bug to me as well.

  • WRT120N: Wireless Client List - Refresh button useless

    WRT120N:
    Wireless --> Wireless MAC Filter --> Enabled --> Wireless client list...
    Opening Wireless Client List on WRT120N shows the list of wireless clients connected.
    Add button is working.
    Close button is working
    But Refresh button is useless. Even if clients on the lists are already not connected to the router, pressing the Refresh button does nothing. It may add new clients connected but can't determine whether the client disconnects or not. The only way to determine if the client is still connected or not is to Reboot the router (Administration --> Start Reboot).
    Refresh doesn't update/remove disconnected clients from the list.
    I'm hoping that on future firmware updates for WRT120N, this can be fixed.

    Did you try to upgrade/re-flash the firmware on your router?
    Connect the computer to the router with the Ethernet cable. Download the latest firmware from Linksys website and save it on your computer. Upgrade/re-flash the firmware on your router. After upgrading the firmware on your router, reset the router and reconfigure it.

  • BT Cloud - Desktop client listing different folder...

    Hello
    I am experiencing a problem with BT Cloud's desktop client listing different folders to the browser version (both executing on the same Windows7 PC with same account details).  BT Cloud application version 2.1.3764 58683eb bt_production.
    The desktop client lists no backups of a new users home directory I have set up to backup (settings -> add folder -> c:/users/xxxx) whereas the browser version reports the directory, sub directory and files.
    I have tried logging out of the destop client and back in, but the problem persists. 
    Has anyone else experienced this and does anyone know if there is a way to correct?
    Thank you

    thedon24 wrote:
    My Windows 7 client used to work fine but I upgraded to the new version at the weekend, and now not only has the new version lost my previous settings for a backup folder, it won't let me add it back again.
    I click the cloud icon then the 'Add folder' button then browse to the folder I want and click 'Select folder' button.
    It accepts a folder on built-in drives (C: and D but ignores (no error or warning message) a folder on USB external drive F: which is the one I want.
    Looks like a failure in regression testing.
    Has anyone else had this problem, and is there a workaround?
    Just a very long shot.
    I only have a small number of files and folders in Cloud, as I'm still trying to come to terms with instructions - so far with success, as demonstrated by a recent system image restore. All files were preserved, after uploading them using the web version of BT Cloud. Even backup files were preserved.
    It's just possible that if you had the f:/ drive unticked or not connected at some point, Cloud took this as a deletion.
    You may just not be able to upload a deleted folder again. You do have problems trying to reload a deleted file.
    Have you tried to rename the folder in the f:/ drive?

  • Getting Wireless client list in WRT54G?

    On one of the other sites Isaw a post showing a URL you could use to get a WRT54G to lsit the currently connected wireless clients. unfortunately this URL did not work on my v5. The DHCP client list is useless because I host my DHCP server elsewhere and don't use the internal server.
    Does anyone know how to tickle a WRT54Gv5 into giving up the wireless client list?
    Thanks In Advance,
    Mark

    The wireless client list is available in the WRT54G v5+.   The URL is http://192.168.1.1/WClient.htm
    The button to display the table is hidden until Wireless MAC Filter is ENABLED on the /Wireless/Wireless MAC Filter page.
    http://192.168.1.1/WFilter.htm

  • DHCP client list empty on WRT310N

    This has happened all 3 times I reset my router to default settings.  I see the list of clients, no problem.  However, when I adjust the QoS for my desktop's MAC address, the client list empties, and from that point on, it stays empty, although 3+ clients are connected.  Removing any QoS settings won't alleviate my problem, either.  I have to reset to factory defaults again. 

    Have you tried to upgrade the firmware of your Linksys Router. If not then Go to website linksysbycisco.com/downloads.. .......insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop...
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

  • About my Dynamic DHCP Client List

    In my eH100 Network settings under Dynamic DHCP Client List it shows two hosts. My MAC address with no name and another MAC address with a name. Does that mean someone is using access through my router. Now it's only showing one host.

    What is a EH100? A DSL or cable modem or router with wireless capability? IF so, it is likely that somebody is "fare-jumping" wirelessly onto your network, if you have no security set up on your wireless.
    IF you currently are an open network, I would recommend a combination of configuring your wireless access point with WPA-PSK security plus MAC authentication. (I hear there is a better one than WPA, which is itself better than WEP, but neither my computers nor modem support any better than WPA). On my ActionTec DSL modem/router/WAP, this is set in Advanced Settings under wireless settings (to specify WPA) and a clearly labeled MAC authentication link for the MAC address list. For MAC authentication, manually add hardware ethernet addresses as found in each authorized computer's system preferences > network > Airport or Built-in Ethernet as Airport ID or Ethernet ID given in the form of xx:xx:xx:xx:xx:xx), depending on how they will be accessing your WAP/router/modem.
    FWIW, this actually would have probably been more fitting to post over in the networking forum.
    (if you find that this solves your problem, or is actually helpful towards arriving at a solution to your problem, please consider clicking on either the "helpful" or "solved" buttons in the header of my post)

  • OK since midday today firefox 3.6.24 apparently no longer executes javascript on ebay. Can't use the "add to watch list" buttons or the enlarge photo buttons. It says 'javascript at the bottom of the firefox window but nothing happens.

    just as I wrote above.. ebay loads and functions. I can bid and view auctions but trying to either use the "add to watch list" or "add to wish list" buttons or to switch between different posted photos of an item just gives me javascript:; at the bottom left of my screen but clicking the button has no effect.I'm still running 10.4.11 with the last java download.. is this an ebay change to a newer java version not supported by my os or is it a firefox error..oh and one more thing each page seems to have become 4 times longer..ie there is a huge empty space as I scroll down the page before I hit the bottom.Only appears to do this on ebay..haven't found any other sites showing similar errors and everything works fine on my imac running firefox 4 under 10.5

    Craig Stenton: at 12:13:04
    but I can't install windows! During the install I am asked for the product key and it tells me that it is not valid and so I can't proceed.
    Craig Stenton: at 12:14:16
    I can't use the usual methods of activation because I cannot get an activation code. I can't use the activation wizard. I can't call the number because it requires an activation code.
    Hi,
    I'm a bit confused with this paragraph, as you said Vista already install on your computer, why did you say Windows can't be installed?
    According to your description with your problem, it is Product edition and key are not match. Firstly of all, we must make sure the system you installed on your computer was
    Windows Vista Business, not matter 32 or 64 bit.
    Note: you can check current system edtion at System Properties.
    After that, you can try to input your product key and activate your system for test.
    If problem still presists, it would be better to provide the activation error message.
    Roger Lu
    TechNet Community Support

  • Can 'track list' button show your playlist rather than album track list?

    Hi all
    My 3GS iPhone has my music on it in the form of whole albums which live in individual playlists on my Mac, but I also have playlist 'mixes' which I've created from various songs from multiple albums.
    When selecting to play a 'mixed' playlist on my iPhone I tap on it, tap the first song to start the music playing, but then if I tap the top right 'track list' button, instead of showing all the tracks in my created playlist it just shows the entire album tracks from where this particular song has come from. Visually I prefer the 'track list' screen but it seems I can't use it if I'm playing a 'mixed' playlist. Is there any way around this?
    Also, this is the same if I have a double CD album: once I hit the 'track list' button it shows just CD 1 (or 2 if I'm further down the play list of course), rather than all the tracks even though on they all live in one single playlist on my iTunes. I've even taken the starts of the track names off (some of them start with '1_01 Song Title' for example) when importing them into iTunes to see if that helps but it doesn't: the iPhone KNOWS how that track was originally supplied!
    Any help or clarification on this would be very helpful!
    Markos

    sadly, that kind of customization is only easily doable on a computer. the iPhone and it's core apps can not be changed by users. you can request the feature be put in, but unless there are a LOT of requests, you shouldn't get your hopes up as there are a lot of these kinds of requests, and by implementing it, how many other users would be angry and demand it be changed back? http://www.apple.com/feedback/
    if you are playing a song that you selected in a playlist, you should be able to hit the 'back' button in the top left to go back to the playlist and view your songs in the playlist.
    in regards to the 'cd 1 of 2' thing, you will need to change your song info to get this to show in the format you want. to see the song info, select a song and go to 'file -> get info'. that will show you all of the ID3 tag information, which you can edit to do whatever you want.

  • E4200v2 - DHCP client list NEVER displays

    As the most expensive and hyped "consumer router" at the local big-box stores, and after already returning a Netgear N600 that appeared to be defective, I had high hopes that this router would work properly and I could stop fooling with router settings and move on to real work. And I'll acknowledge that for a lot of folks this router will probably be fine. I didn't do any speed measurements or methodical testing, but it seems pretty fast and using it for more than three weeks it seemed reliable. However, it had several issues that were maddening and ultimately for me, unacceptable. Summarized as follows:
    > The DHCP client list NEVER displays all the clients connected on my network, no matter how many times I look. These clients are actively transferring data, and I can download free programs from the web that report all clients reliably. Why is this so difficult??
    > The logging feature is ridiculous - it often didn't log events that I knew had occurred, and even when they were shown, you would only see an entry if you checked the log very quickly after the event (some sort of "auto-flush" function that makes the whole feature pretty useless).
    > The previous issues are annoying - but this was the deal-breaker. I could not connect to an OpenVPN device on my network through this router. I could connect to the device locally, I could connect to other devices remotely through other forwarded ports, and I could see in the log (if I looked quickly enough) that the router was seeing the connection attempt to the OpenVPN device, but it was getting blocked. Many hours searching forums and experimenting with router settings / firmware updates did not help.
    > In the pursuit of resolving the third issue, and with very low expectations, I contacted Linksys tech support. This proved to be a complete waste of time. After working through the front-line guy who only knew how to look through the User's Guide, I was connected to another person who was even more clueless and was almost robotic in his hard-coded sequence of attempts to guide me through silly procedures that had absolutely nothing to do with my problem. After again asking if I could speak to someone that might actually understand the issue I was put on hold for more than 20 minutes, at which point the call was disconnected (I think this means they hung up on me).
    So once again I'm returning an expensive router that doesn't work properly and will be trying something else. It shouldn't be this difficult.

    With reference to your post I would like to know that does all the client devices on your network runs on DHCP or some of them have static IP address as well? The devices which are running on static IP address will not be displayed in the DHCP client table.
    Regarding the logs that are not being created on the router for any event that takes place could be because of the reason that you might be using another router or a gateway before your linksys router.
    As far as your VPN issue is concerned please try to disable the firewall of the router and then try to connect to the open VPN device because this router acts like a VPN passthrough. Click on the following link to know how to disable the router's firewall http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=87795adab27b4bd7a432e03be4e28e8d_17347.xml&pid=80&...

  • Download list button in upper right corner hinds under "Reader" button? Unable to find down loaded file in the download folder afterward?

    The Download list button in upper right corner of screen hides under "Reader" button?   Does not show down loaded(?) file in the download folder afterward?
    Trying to run a brokerage firm streaming quote app with java.  Wondering if I may have deactivated the Download list button some how?

    Hey Sgt.Rics,
    It sounds like you're experiencing some unexpected behavior in Safari, specifically the window layout blocking the Downloads button. I would check and make sure no third-party add-ons are causing the issue:
    Safari: Unsupported third-party add-ons may cause Safari to unexpectedly quit or have performance issues
    http://support.apple.com/kb/TS3230
    Welcome to Apple Support Communities!
    Take care,
    Delgadoh

  • The Downloads Clear List Button Not Working In Firefox 19.0

    Hello,
    After upgrading Firefox to version 19.0 today, I noticed that the Downloads Clear List Button does not work & is always grayed/greyed out, and so you can not clear all downloads; and so you have to remove them each one-at-a-time.
    I did not have this problem until upgrading to version 19.0
    Screenshot:
    http://www.use.com/showoriginal.pl?set=1c0659d1946249dc69dc&p=1
    Thank you,
    -John Jr

    I made a bug report:
    https://bugzilla.mozilla.org/show_bug.cgi?id=845450

  • Search list button active in Find Mode

    Hi all,
    On the item master in Find mode, the search list button on the preferred vendor field is not working. Is this correct?
    Thanks,
    jane

    Hi Gordon,
    How do I change Form Setting for this CFL to add Display Description for this field?
    Thanks,
    Jane

  • Drop down list button in the WDP Abap interactive form

    Hi Gurus,
    I wanted to implement the drop down list button in the WDP Abap interactive form. Once the users clicks on the drop down button, an RFC should be called and display the details under the drop down button. Please give me the logic with code. Its very urgent...please help me. Please note that it is in WDP Abap interactive forms. We are using NW2004S, ECC6.0.

    hi david,
    all the UI elements in the adobe form are generally connected to your web-dynpro Context.
    whatever you type in the online adobe form is reflected in the respective context attributes of the dynpro Context of the view where "ur Interactive form UI element is".
    that means you can yourself fill the contents of ur interactive form by working on the get/set methods of the context attributes.
    Likewise you can clear the form by setting all context attributes to blank eg ""
    with regards,
    -Amol Gupta

Maybe you are looking for