WLC 2100 configuration
Hello,
I have 2100 wlan controller and wlapp ap connected to switch (catalyst 3560).
when I configure the controller with basic configurations , I can not access the webmode anymore with the management ip interface.
can you help me please.
Br
Yamani
Hi Yamini,
Issue the command "show network summary" on the WLC cli and verify whether the WEBMODE is enabled.. if not then issue the command..
"config network webmode enable" and try accessing the GUI.. if we have enabled the Webmode and still not able to access then, check for the duplicate IP assigned...
Regards
Surendra
Similar Messages
-
LAP1142 can not join wlc 2100 !
I'd WLC 2100 series and 9 access point LAP1142N .
8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not .
Could you help me to solve it ? Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 2 10:52:52.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.28.21 peer_port: 5246
*Apr 2 10:52:52.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 2 10:52:52.667: LWAPP_CLIENT_EVENT: lwapp_check_image_good: image is good now
*Apr 2 10:52:53.107: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.28.21 peer_port: 5246
*Apr 2 10:52:53.108: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.28.21
*Apr 2 10:52:53.108: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: ap model AIR-LAP1142N-A-K9
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: ap sw version 12.4(23c)JA
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: lwapp_encode_ap_reset_button_payload: reset button state on
*Apr 2 10:52:53.237: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 2 10:52:53.240: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.28.21
*Apr 2 10:52:53.240: %DTLS-5-PEER_DISCONNECT: Peer 172.16.28.21 has closed connection.
*Apr 2 10:52:53.241: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.28.21:5246
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnDeleteAllMobiles radio 0
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnLockDevice radio 0
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnDeleteAllMobiles radio 1
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnLockDevice radio 1
*Apr 2 10:52:53.280: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 2 10:52:53.280: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 2 10:52:53.286: LWAPP_CLIENT_EVENT: spamInitCfgData: Loaded configuration into v2 struct (version 7.0.98.0)Actually, 5.2 or later is needed.
5.0 and 5.1 do not even support 1140 Access point.
Rating useful replies is more useful than saying "Thank you" -
I need to intergrate WLC 2100 with ACS 5.0
i have a cisco ACS version 5.0, I need to authenticate a wireless users connected to WLC 2100 controller
when i connect the controller to a Dot1x port in the switch , the port go down.
if any helpLaith,
Nicolas is right about the dot1x switchport. If you want to authenticate all users on a specific SSID using 802.1x, then you will need to configure the radius serve in your WLC under Security | Radius | Authentication. Then on the WLAN SSID, you need to set the radius server information on the WLAN | SSID | Security | AAA. I suppose the radius already has a certificate installed since you are using dot1x on the switch side.
Here are some links:
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080b4cdb9.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665d18.shtml -
Hello Guys, please someone help me.
I can't access the gui from cisco WLC 2100 device, i changed IP's to the same subnet, connected straight-through cable on both interfaces (Notebook & WLC), i can ping, but can't access the GUI by using ethernet connection.
I've tried to access the GUI using WI-FI and it worked perfectly, but i still can't access using ethernet, please give me advices!
Is there a way to upgrade WLC IOS using wireless?
ThxGo to console of the WLC & post "show interface detail management" output. In WLC Which ports connect back to switch & what is the switch port configuration looks like ?
In the switch, post "show run interface x/x" where x/x is connecting to your 2106.
Rasika -
WLC 2100 series Guest LAN not found
Hi there
I am unable to configure Guest LAN as in this link
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml
because my Cisco WLC 2112 version 7.0.240.0 does not have the option for Guest LAN. Is Guest LAN supported for WLC 2100 series? Any workarounds or suggestions?
Thanks for your help
DIegoDiego,
Wired guest access is not supported on WLC2106.
Reference:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml#configs
consider using a WISM, WLC4400, 3750 integrated WLC or a WLC5500 -
WLC 2100 and DHCP strange issue.
Hi,
i have this scenario: 1 WLC 2100 and two LW AP 3500 connected. If the access points are connected via external switch evrything works well - AP and Clients get IP address from external DHCP and this is ok but when im connecting AP 3500 directly to one of ports on WLC i need to chceck in controller web Controller -> Advanced -> DHCP -> Enable DHCP proxy - after that AP get IP addres and clients get too but ip is assigned from external dhcp but the gateway is set as controller IP address (!!!) so clients not works. I want to configure access points connected directly do WLC.
I have small setup and i have configured all in the one vlan - management dla users are in the same vlan.
And the second is - for what usage is internal DHCP server - and how to use it?When "Enable DHCP Proxy" is not enabled tha LW AP 3500 cannot get IP address if it is connected directly to LWC... when i add this option then on both LW AP 3500 - one connected to WLC and second directly to switch give me DHCP address from external DHCP but gateway sets as LWC management IP.
I made test - connected client witout "Enable DHCP Proxy":
Client IP 192.168.1.201 (correct in dhcp server logs), default GW 192.168.1.1 (correct gateway for this DHCP) correct dnses and in windws ipconfig i see "Server DHCP 192.168.1.1" all is correct.
Disconnected client and clicked "Enable DHCP Proxy":
Client IP 192.168.1.201 (correct in dhcp server logs), default GW 192.168.1.252 incorrect gateway - ip of WLC management interface) correct dnses and in windws ipconfig i see "Server DHCP 1.1.1.1" that shows that WLC modified DHCP packets... but what it try to set default GW as WLC?
WLC data:
Software Version
7.0.98.0
I can attach screenshots and any other configutation if you need. -
Issue in connecting to WLC 2100 via switch
Hi there, I am trying to setup my lap with a new WLC 2100. but failed to connect to the WLC via second switch.
In WLC 2100, fa0/2 connect to the second switch, Fa0/1 connect to PC.
In second switch 3560, it's fa0/2 connect to the WLC as trunk port. port fa0/1 is in vlan 1
Management int ip in WLC is 192.168.1.1 in VLAN 1 assoicarted with port is fa0/1, the PC ip is 192.168.1.2.
When PC connect via fa0/1 in WLC, I can ping 192.168.1.1 from PC. but connect PC to fa0/1 in 3560, no reply.
To my understanding, fa0/2 in WLC is trunk port by default and the vlan1 is allowed, since fa0/2 in 3560 also configured trunk, there is no reason, why I can not ping the WLC. any suggestion ?Hi Guys,
I have just configure the WLC as above and the result is nagtive.
plug PC to Switch fa0/1 no reply
plug PC directly to the WLC fa0/1 no reply. (was replying first time when I configure the WLC)
seem to me there might be some error in the intial configuration in WLC, since the initial configure is very simple, I post it as following, please help to see if there is any error:
after reset to factory default in WLC 2100:
Would you like to terminate autoinstall? [yes]: yes
System Name [Cisco_32:18:a0] (31 characters max):
AUTO-INSTALL: process terminated -- no configuration loaded
Enter Administrative User Name (24 characters max): admin
Enter Administrative Password (3 to 24 characters): ********
Re-enter Administrative Password : ********
Management Interface IP Address: 192.168.1.1
Management Interface Netmask: 255.255.255.0
Management Interface Default Router: 192.168.1.25
Management Interface VLAN Identifier (0 = untagged): 0
Management Interface Port Num [1 to 8]: 1
Management Interface DHCP Server IP Address: 192.168.1.25
AP Manager Interface IP Address: 192.168.1.2
AP-Manager is on Management subnet, using same values
AP Manager Interface DHCP Server (192.168.1.25):
Virtual Gateway IP Address: 1.1.1.1
Mobility/RF Group Name: MRF-GP
Network Name (SSID): TEST
Configure DHCP Bridging Mode [yes][NO]: yes
Warning! Enabling Bridging mode will disable Internal DHCP server and DHCP Proxy feature.
May require DHCP helper functionality on external switches.
Allow Static IP Addresses [YES][no]: yes
Configure a RADIUS Server now? [YES][no]: no
Warning! The default WLAN security policy requires a RADIUS server.
Please see documentation for more details.
Enter Country Code list (enter 'help' for a list of countries) [US]: au
Enable 802.11b Network [YES][no]: yes
Enable 802.11a Network [YES][no]: yes
Enable 802.11g Network [YES][no]: yes
Enable Auto-RF [YES][no]: yes
Configure a NTP server now? [YES][no]: no
Configure the system time now? [YES][no]: no
Warning! No AP will come up unless the time is set.
Please see documentation for more details.
Configuration correct? If yes, system will save it and reset. [yes][NO]:yes
show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
ap-manager 1 untagged 192.168.1.2 Static Yes No
management 1 untagged 192.168.1.1 Static No No
virtual N/A N/A 1.1.1.1 Static No No -
WLC 2100 Series Rack Mount Option
I am having a tough time finding the rackmount kit for the 2100 series Wireless Lan Controllers. Will the ASA5505-RACK-MNT= work?
Hi David,
Yes, this is the correct part to use :) I am guessing the ASA 5505 and WLC 2100 must use the same chassis;
http://www.cisco.com/en/US/docs/security/asa/hw/maintenance/guide/procs.html#wp104420
Hope this helps!
Rob -
What's the Part Number for the Cisco WLC 2100 rack mount kit?
Thanks in advance.Allows for convenient desktop mounting or rack mounting, with optional rack mount kit for flexible deployment.
http://www.cisco.com/en/US/products/ps7206/products_data_sheet0900aecd805aaab9.html -
WLC - Wlapp configurations problems
Hello,
I have connected the WCS to Wlc and WLC to AP
after giving the WLC basic configurations and AP management ip add, still i can not see the AP from the controller.
should I configure each ap manually and give it an ip add ? or it is enough to put the AP management ip add in the controller?If you can actually manage the WLC using the WCS, you can "force" the WCS to "discover" the AP attached to this WLC.
Simply, in Controller tab, select your WLC and in the upper right list select "refresh config from controller" and GO, then WCS ask you if you want to keep the configuration of the WLC stored in WCS database or "refresh" it deleting the actual configuration; check delete and Go.
Finally, You can review if the AP now is shown by the WCS or not.
Best Regards. -
Just purchased and installed a Cisco WLC 2100. I am getting the following message on the controller:Decrypt errors occurred for client 00:18:de:82:eb:57 using WPA2 key on 802.11b/g
The client is connecting but I am not getting a dhcp address.Hugh,
What code verson is running on the WLC? If you are running any 6.0 other than 6.0 199.0, then you need to upgrade as there are some nasty bugs in the other 6.0s. One of which allows a client to associate, but then not be able to get an IP and all you see on the controller is decrypt messages. There is a software advisory for these issues:
http://www.cisco.com/web/software/Wireless/Deferral/Software_Advisory_6_0_196_0.html
Thanks,
Lee -
Switchports of wlc 2100 dont bridge to rest of the LAN
Hi,
I've configured several WLC's before but I'm new to the 2100 series. I'm a bit confused in the way the 8 ports function. I have the following setup:
2 AP's (1131AG)
3 clients's (wired)
All five connected to WLC on ports 8,7,6,5,4
WLC port 1 is connected to a 24 port switch, non Cisco, so no CDP info available (may that matter).
The whole network should be an untagged Vlan. This is also the way I've runned the basic setup. AP int + MGM int are both untagged configured on port 1.
So I would like the 8 ports to function as an "expansion" to the 24 port switch. But for some reason there is no traffic possible between the wired clients+ap's on the WLC and the rest of the network.
Both sides can ping the AP int + MGM int of the WLC.
DHCP proxy works as well, the AP's get their IP, the wired client's dont.
As soon as the AP tries to resolve CISCO-CAPWAP-CONTROLLER.domain.local it fails, when connected to the 24 port switch, it succeeds, because the DNS server is on that side.
Am I missing something here?
Thanks for your help!
Update: WLC is running the latest version7The ports on the 2106 are designed to support AP connections or an uplink to a switch. They will not work with PC's connected to them.
-
Hi everyone,
Seems as per cisco all WLC --5500/2100 etc are effected by sslv3.
Need to know if there is any config change that can be done without doing version upgrade?
Regrads
MaheshIf you do not want users to connect to a web page using a browser that is configured with SSLv2 only, you can disable SSLv2 for web authentication by entering the config network secureweb cipher-option sslv2 disable command. If you enter this command, users must use a browser that is configured to use a more secure protocol such as SSLv3 or later releases. The default value is disabled.
-
Hi Everyone,
I am new to Wireless.
Need to know few commands to check the health ,status and troubleshooting for WLC2100?
Like CLI command to check how many AP are connected ?
What users are connected to AP or WLC?
how to check which radius servers are configured on WLC?
Regards
MAhesh
Message was edited by: mahesh parmarPlease check the below link for step by step configuration:
http://www.cisco.com/en/US/docs/wireless/controller/2100/quick/guide/ctrl206q.pdf -
Cisco WLC 2125 configuration help
So in a nutshell, from My computer I can ping all VLANS - everything seems to in workding order.
when telnet to the HP 5406zl core routing switch I can ping all VLANs and other parts of the network
But when logged into the Cisco wireless Lan Controller I cant ping VLAN 108 gateway IP (172.24.156.2 ) from the neighbour switch or other services on this VLAN
for example cant ping the DHCP on this vlan from WLC.
The neighbour switch can ping IP of the management interface created on the WLC
WLC cant ping VLAN 108
WLC can ping all other VLAN 102,104,106
Not sure where the problem is ??
Configure Dynamic Interfaces on the WLC for the Guest and Internal Users - DONE
Create WLANs for the Guest and Internal Users - DONE
Configure the 5406zl Layer 2/3 Switch Port that Connects to the WLC as Trunk Port allowing the relevant vlans i.e. management vlan, vlan 102 and Vlan 108 - DONE
Configure the Switch Port that Connects to the AP to VLAN 102 - DONE
configure virtual interface IP 1.1.1.1 - DONE
Configure the Router for the WLANs - DONE
LAP is registered to the WLC - DONE
WLAN and SSID broadcast - OKNot at present it is not, the port on the 5406zl that the WLC is connected was setup as a trunk group and All VLAN tagged. When I tried this I lost all connectivity to the WLC. Is there something on the WLC that need changing also?.
Maybe you are looking for
-
Parsing error in ejb-jar.xml
I am trying to build the war file using apache Ant1.5. But I am getting following error - [ejbjar] Could not resolve ( publicId: -//Sun Microsystems, Inc.//DTD Enterprise JavaBeans 2.0//EN, systemId: http://java.sun.com/dtd/ejb-jar_2_0.dtd) to a loca
-
Hi, all Yesterday, OVM Server3.1.1 was crashed. due to ovspoolfs.img was corrupted. I recovered ovspoolfs.img.(but OVM Manager didn't recognize that server.) Main problem is that Filesystem goes read-only. I checked out /var/log/messages. but There a
-
Elements 10 will not display my slideshows in full screen, any ideas?
My 'Full screen preview' remains square with black borders down the left and right sides. The same happens when outputting to DVD for replaying on TV. I previously ran Elements 4 on my old machine without this problem! I would appreciate some help
-
Hello together, I'm a little bit frustrated. The follwoing is my problem: I want to insert some values from an Oracle 10gR2 database into a MSSQL database (SQL Server 2008 R2). Therefor I'm using DG4ODBC 11.2.0.3. The connection is working absolutly
-
EvDRE vs evGET - DRE pulls wrong data
BPC 5.1 SP3 I added one calculated member to the second hierarchy of a two-hierarchy user-defined dimension. The H2 formula is this: [FUNCACCOUNT].[H2].[F_3RDNETSALES]-[FUNCACCOUNT].[H2].[F_3RDGROSSPFT],solve_order=99 F_3RDNETSALES and F_3RDGROSSPFT