WLC 2106 ports and vlans

I am connecting a 2106 to our small network.  If I set a specific port on the 2106 for the "guest interface" and wire that port directly to the DMZ is it still necessary to define a VLan?  Does defining the ports separate the traffic?
What I am thinking is leaving all (except the guest wireless) of the interfaces on port 1, wiring that to our normal network and setting up radius authent.  All of the network traffic then goes out through the normal firewall interface.
Then setup the guest interface to go to "port 4" on the 2106.  Run a wire fom "port 4" to a NIC dedicated to the DMZ.
Note:  The "nics" listed above are actually PNics on separate VSwitches in VSphere.
Thanks,
Bob

Thanks for your help!
It looks as if I need to read up some more on the use of this unit.  It was dropped in my lap by a third party so I am kind of faking it.  Any other suggestions would not hurt my feelings:
Internal network is 192.168.5.x, guest wireless is  172.16.1.x.  At this point I am going to have all interfaces go to "port 1" except the guest wireless which will go to "port 4".
I will plug "port 1" into my regular switch and "port 4" into a DMZ switch.
From what I gather I will have to give the "port 4" traffic an exclusive "VLan indentifier", change the Vsphere switch to include that VLan, etc.
Thanks again,
Bob

Similar Messages

  • WLC 2106 and Linksys Bridge WET610N works with 7.0.116.0 release?

    Hi all,
    i'm having troubles with WLC 2106 controller and several wireless bridges, so i'd like to know if i can fix it in some way.
    My environment is as follows:
    1 WLC 2106 with 2 Aironet 1240G
    I have a production appliance that needs an ethernet port to work, so i bought a Linksys Bridge WET610N to make it works via wireless.
    The Linksys bridge connects to the 1240G as a client and works well, but the appliance connected to the ethernet port of the bridge is unreachable.
    Searching for the problem, i found that the wlc act as a proxy arp for the wireless clients and being the ethernet appliance a "passive" client, the controller isn't aware of it.
    My WLC is running the 7.0.98.0 firmware. In the release notes for the 7.0.116.0, in the "Non-Cisco WGB Support" seems to state that now also non cisco bridges can work using the passive client feature. I've already enabled it on my controller but this didn't solve my problem.
    Can anyone tell me if the upgrade to the 7.0.116.0 can fix it?
    Thanks in advance
    Riccardo Coppola

    I'm not sure what (cheap) devices can do the wgb feature that is inter-brand compatible.
    The thing is that the WLC enforces the rule "1 wireless client = 1 client". Meaning you can't bridge multiple clients behind a wireless clients, that just screws up roaming mechanisms etc ...
    Cisco WGBs have the IAPP protocol to tell the WLC "listen, I'm a WGB wireless client and those are the wired clients connected to me, allow them on the network".
    What does "universal WGB" feature does is that the WGB forwards the traffic of the client (only 1 client supported in this case !) to the infrastructure AP but the WGB never sends anything with its own mac address. It uses the client mac address as source.
    This means that the WLC has no way of knowing that there is more than 1 device. It just thinks that your wired client is a wireless client.
    So it's more than mac cloning since the WgB has to be the one authenticating to the infrastructure (Wpa/wpa2 whatsoever) by spoofing the client mac. The WGB is still in charge of roaming decisions and so on and so on...
    I hope it clarifies the situation ?

  • WLC 2106 Configuration steps

    I have WLC 2106,And 5 LWAP, 3 Cat3560 Switches.and my 2851 CME router providing DHCP for Data VLAN 1 nad Voice VLAN 100
    any one can please help me how to do the basic configuration
    when i configure Managment and AP manager on WLC 2106 on untaged VLAN 0 i can able to ping but when i cahnged the VLAN to 1 im not able to communicate to WLC from switch or any port from WLC
    please help me to configure the WLC
    Thanks & Regards
    PRajoth

    The software guide states "A zero value for the VLAN identifier (on the Controller > Interfaces page) means that the interface is untagged.
    The default (untagged) native VLAN on Cisco switches is VLAN 1. When controller interfaces are configured as tagged (meaning that the VLAN identifier is set to a non-zero value), the VLAN must be allowed on the 802.1Q trunk configuration on the neighbor switch and not be the native untagged VLAN.
    Cisco recommends that only tagged VLANs be used on the controller. You should also allow only relevant VLANs on the neighbor switch's 802.1Q trunk connections to controller ports. All other VLANs should be disallowed or pruned in the switch port trunk configuration. This practice is extremely important for optimal performance of the controller.
    Note Cisco recommends that you assign one set of VLANs for WLANs and a different set of VLANs for management interfaces to ensure that controllers properly route VLAN traffic"
    Can you supply a screen shot of the interfaces page from your WLC and supply the WLC switch port configuration also? Just to sanity check what you have so far?

  • WLC-2106 and multiple interfaces on the same network

    Hi there,
    I recently created a TAC request to the Cisco support regarding our WLC-2106, but they could not help me. Basically I just learned that you can create new interfaces for the wireless LAN controller and then dedicate them to a given wireless network (SSID). This way I could more effectively utilize network bandwidth also. Problem is that all of the interfaces have to be in a different network segment in order to work, which is not what I want. I specifically want to have several interfaces on the same network segment.
    Has anyone tried to accomplish the same?

    Basically what I've misunderstood is that all the traffic generated by our wireless clients have been going through the single 100Mbit/s ethernet port on the wireless LAN controller (management interface), and to mitigate this I thought I could create new interfaces (ports) and dedicate those to given WLAN networks.. I see now that this is not supported. Not inside the same network at least.
    So, by reading further and consulting my best friend Google I learned about a setting called "AP Mode". Changing that from Local (the default) to H-REAP the APs should not route their traffic anymore through the management interface on the wireless controller, but instead route all the client traffic directly to the local LAN. This way you effectively remove the 100Mbit/s bottle-neck when all the APs were using the management interface both for configuration and client data traffic.
    It seems you also have to enable H-REAP Local switching from a given WLAN network in addition to changing the AP Mode of your access points to H-REAP. I'm still in the testing phase here so should anyone have any insight to this, I'd be greatful to hear more.

  • Wlc management port can't trunk other than native vlan

    Hello,
    Ihave installed my first WLC 5508 with this topology :
    WLC Connected trought distrubtion SFP 1Gb port to Core Switch port configured as Trunk port permetting 3 Wireless VLAN :
    - Management WLC, Wireless Voice and Wireless Data Vlan (native Vlan is management WLAN).
    - I have created 2 dynamic interface on WLC regarding my Wireless VLAN :
    10.7.1.0/24 : Defaut Management Virtual Interface when installing WLC +
    10.7.6.0/24 : Voice Virtual Interface and
    10.7.2.0/24 : Wireless Data Virtual Interface trought GUI.
    DHCP configured on each dynamic interface is the L3 vlan interface for equal VLAN subent for CORE SWITCH contining IP DHCP Pool.
    WLC Management Inerface IP adress is : 10.7.1.10/24
    I Have  create 2 WLAN with SSID named Data  ID 1 & Voice ID2.
    I have create and AP Groupe named APGRP1 containing the AP registered on WLC and using both SSID WLAN.
    Both AP are connected to Switch acess port configured as access port to native management WLC VLAN.
    I have create 3 IP DHCP pool on Core switch with related L3 Interfaces for Inter VLAN routing.
    Problem: when I try to connect from laptop to Data SSID  I get IP Address from management WLC VLAN a non DATA VLAN.
    the same case from Wireless IP Phone configured with Voice SSID.
    What can I modifie that permet to both device to get IP address from the correct VLAN?
    Thnks

    Hi Adil,
    Q1 >> AP access port on the switch must be configured on an Access port mode or trunk mode?
    ANS - The  LWAPP/ CAPWAP APs connected to the switchport should be a Access port not trunk.
    Q2>> if the first case, setting the port on, the same VLAN like WLC Management VLAN will support other WLAN Vlans (voice and data)?
    ANS - Yes it does support, since the traffic which involes the WLAN will be inside the LWAPP/CAPWAP logical tunnel.
    Q3>> I will verify the interface mapping between WLAN and Dynamic Interfaces and i will tell you.
    ANS - I will be waiting for your response!!
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

  • AP 1140 and WLC 2106

    Does someone know if WLC 2106 support AP 1140 ? I read that AP 1140 is CAPWAP only and I don't know if WLC 2106 supports CAPWAP.
    Thanks

    Yes it does, you may have to upgrade your controller software to get 802.11n and CAPWAP, use the latest code 6.0.182.
    CAPWAP was supported from code 5.2.157
    The max throughput on the 2106 though is only 100mbps so yo wont see the highest speeds

  • WLC 2106 and iPhones

    Just recently I am having issues with my WLC 2106 WiFi network and iPhones.  For the past week, the iPhones have been locking up the network much like as it was described with the ARP issues with the exception that what I have been reading, this issue did not effect the 2100 series.
    I've done searches but have not found anything applicable to what is happening now.
    Any help will be GREATLY appreciated.

    It's running on v. 4.0.217.0.  Right now I'm controlling who is accessing the wifi via MAC filter to prevent anyone with an iphone to log on but that just doesn't cut it since there's a lot of visitors coming in to use the wifi.
    I won't be able to go in and do more testing for a week or two to get that debug log.
    But this seems to be a common issue with at least the 2106s.  As soon as anyone logs in with an iphone, the controller locks up and the only thing to do is reboot.  It only fairly recently started happening so maybe it's only with the newer iphones?

  • Port Channel and VLAN trunking

    When configuring trunking of VLANS accross a Port Channel, do we need to configure vlan pruning on both the port-Channel port and the physical ports ???
    E.g. do I need to apply the "switchport trunk allowed vlan add " command under each physical port and the port channel port ? Or only under the port channel port ?
    Thanks

    In short, yes. Configure the port channel interface exactly as you do the physical interfaces and both ends should be an exact match. otherwise you will have problems getting the channel to come up or stay up.
    -Mark

  • 4500 Aggregate policers and Per-Port Per-VLAN QoS

    Hello,
    I want to limit the aggregate traffic of multiple VLANs on a trunk using an aggregate policer. I also need Per-Port Per-VLAN QoS for other VLANs on the same trunk.
    To cut a long story short, will the example config below work?
    qos aggregate-policer pol_aggr_10Mbit 10m 12.5k conform-action transmit exceed-action drop
    policy-map Aggr_10Mbit
    class class-default
    police aggregate pol_aggr_10Mbit
    policy-map Limit_10M
    class class-default
    police 10m 12.5k conform-action transmit exceed-action drop
    interface GigabitEthernetx/y
    switchport trunk encapsulation dot1q
    switchport mode trunk
    ! Aggregate 10Mbit VLANs
    vlan-range 208, 316, 909
    service-policy output Aggr_10Mbit
    ! 10 Mbit VLANs
    vlan range 20, 50-100
    service-policy output Limit_10M
    Regards, Jan

    Your config looks good . Actually Per-port per-VLAN QoS (PVQoS) offers differentiated quality-of-services to individual VLANs on a trunk port. It enables service providers to rate limit individual VLAN-based services on each trunk port to a business or a residence. In an enterprise Voice-over-IP environment, it can be used to rate limit voice VLAN even if an attacker impersonates an IP phone. A per-port per-VLAN service policy can be separately applied to either ingress or egress traffic.

  • WLC 2106 problem

    Hello,
    I have problem with new one WLC 2106 controller. I make this basic configuration (after reset):
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap-manager                       1    10       10.10.10.21     Static  Yes    No
    management                       1    10       10.10.10.20     Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    At this point, everything works OK. Controller is accesible via HTTPS, AP (one 1130) is connected too. But next I need create new WLAN and another interface VLAN - named ak-lan
    config interface create ak-lan
    config interface port ak-lan 1
    HTTPS acces is still working, but when I configure IP adress:
    config interface address dynamic-interface ak-lan 10.10.11.10 255.255.255.0 10.10.11.1
    HTTPS acces stops. In fact, it seem like HTTPS starts on new interface - it's accesible via 10.10.11.10, but (after certificate warning) shows only empty page (Page is not accesible..)
    I dont have an idea why. I tray downgrade software (originaly comes with 7.0.98.0) to 6.0.196.0, whitch I use on another same controller, but the behavior is the same. Now I use software 6.0.199.4. Again the same behavior.
    "show interface summary" says:
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ak-lan                           1    11       10.10.11.10     Dynamic No     No
    ap-manager                       1    10       10.10.10.21     Static  Yes    No
    management                       1    10       10.10.10.20     Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    (Cisco Controller) >
    All interfaces (excluding virtual) matched to ping. All ïnterfaces have netmask 255.255.255.0.
    There was another strange thing - "show sysinfo" says that I use sw 6.0.199.4 and emergency is 7.0.98.0, but "show boot" says:
    (Cisco Controller) >show boot
    Primary Boot Image............................... 6.0.199.4 (active)
    Backup Boot Image................................ 6.0.196.0
    (Cisco Controller) >
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    RTOS Version..................................... 6.0.199.4
    Bootloader Version............................... 4.0.191.0
    Emergency Image Version.......................... 7.0.98.0
    Build Type....................................... DATA + WPS
    System Name...................................... ak-wlc
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.828
    IP Address....................................... 10.10.10.20
    System Up Time................................... 0 days 0 hrs 46 mins 35 secs
    System Timezone Location.........................
    Configured Country............................... DE  - Germany
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +55 C
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 0
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ E0:5F:B9:63:7B:00

    Switch is C2960, port Gi0/2:
    Gi0/2     T wlc              connected    trunk      a-full  a-100 10/100/1000BaseTX
    interface GigabitEthernet0/2
    description T wlc
    switchport trunk allowed vlan 10,11,100
    switchport mode trunk
    end
    VLANs are set properly. Router is ASA 5510, and routing is fine. Morever, interfaces on WLC is accesible via ping (I dot't try telnet or ssh).

  • I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .

    HI All,
    I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
    Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
    The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
    here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
    show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"   , DESCR: "Cisco 5500 Series Wireless LAN Controller"
    PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.235.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS
    System Name...................................... WLAN Controller 5508
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 10.125.18.15
    Last Reset....................................... Software reset
    System Up Time................................... 41 days 5 hrs 14 mins 42 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... US - United States
    --More or (q)uit current module or <ctrl-z> to abort
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +20 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 10
    Number of Active Clients......................... 61
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    AP Bundle Information
    Primary AP Image  Size
    ap3g1             5804
    ap801             5192
    ap802             5232
    c1100             3096
    c1130             4972
    c1140             4992
    c1200             3364
    c1240             4812
    c1250             5512
    c1310             3136
    c1520             6412
    c3201             4324
    c602i             3716
    Secondary AP Image      Size
    ap801             4964
    c1100             3036
    --More or (q)uit current module or <ctrl-z> to abort
    c1130             4884
    c1140             4492
    c1200             3316
    c1240             4712
    c1250             5064
    c1310             3084
    c1520             5244
    c3201             4264
    Press Enter to continue or <ctrl-z> to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Strong Password Check Features:
           case-check ...........Enabled
           consecutive-check ....Enabled
           default-check .......Enabled
           username-check ......Enabled
    Press Enter to continue or <ctrl-z> to abort
    Network Information
    RF-Network Name............................. OGR
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    OCSP........................................ Disabled
    OCSP responder URL..........................
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    IGMP Query Interval......................... 20 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    --More or (q)uit current module or <ctrl-z> to abort
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Web Auth Proxy Redirect ................... Disable
    Fast SSID Change ........................... Enabled
    AP Discovery - NAT IP Only ................. Enabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or <ctrl-z> to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr Type   Stat   Mode     Mode     Status   Status Trap    POE   SFPType  
    1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
    2 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    3 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    4 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    5 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    6 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    7 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    8 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    Press Enter to continue or <ctrl-z> to abort
    AP Summary
    Number of APs.................................... 8
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1       US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1       US       1
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1       US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1       US       1
    Anham_AP03           2     AIR-LAP1142N-A-K9     70:81:05:88:15:b5 default location 1       US       1
    ANHAM_AP01          2     AIR-LAP1142N-A-K9     70:81:05:b0:e4:62 Small Conference 1       US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1       US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9     70:81:05:96:7a:49         Copy Room 1       US       1
    AP Tcp-Mss-Adjust Info
    AP Name             TCP State MSS Size
    KNOWLOGY_DC01       disabled   -
    KNOWLOGY_DC02       disabled   -
    --More or (q)uit current module or <ctrl-z> to abort
    KN1252_AP01         disabled   -
    KN1252_AP02         disabled   -
    Anham_AP03           disabled   -
    ANHAM_AP01           disabled   -
    ANHAM_AP04           disabled   -
    ANHAM_AP02           disabled   -
    Press Enter to continue or <ctrl-z> to abort
    AP Location
    Total Number of AP Groups........................ 3  
    Site Name........................................ ANHAM8075
    Site Description................................. ANHAM 8075 Location
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Anham_AP03           2     AIR-LAP1142N-A-K9   70:81:05:88:15:b5 default location 1     US       1
    ANHAM_AP01           2     AIR-LAP1142N-A-K9   70:81:05:b0:e4:62 Small Conference 1     US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1     US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9   70:81:05:96:7a:49         Copy Room 1     US       1
    Site Name........................................ Knowlogy_DC
    --More or (q)uit current module or <ctrl-z> to abort
    Site Description................................. DC Center Access points
    WLAN ID         Interface         Network Admission Control         Radio Policy
    2               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1     US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1     US       1
    Site Name........................................ OGR
    Site Description................................. 1934 OGR Office
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                        None
    4               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    --More or (q)uit current module or <ctrl-z> to abort
    7               knowlogy_ogr        Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1    US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1     US       1
    Site Name........................................ default-group
    Site Description................................. <none>
    WLAN ID        Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    5               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                          None
    --More or (q)uit current module or <ctrl-z> to abort
    9               knowlogy_ogr         Disabled                         None
    10             management           Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Press Enter to continue or <ctrl-z> to abort
    AP Config
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch IP Address.................. 10.125.18.15
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
        Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
        Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
    --More or (q)uit current module or <ctrl-z> to abort
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 11
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
    --More or (q)uit current module or <ctrl-z> to abort
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
          CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
          36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
         Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 44
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    --More or (q)uit current module or <ctrl-z> to abort
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
        Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
    --More or (q)uit current module or <ctrl-z> to abort
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 1
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
         Coverage exception level................... 25 %
    --More or (q)uit current module or <ctrl-z> to abort
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
           36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
        Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 36
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
          Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 5
    Cisco AP Name.................................... KN1252_AP01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:ef:06:50
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.125.18.101
    IP NetMask....................................... 255.255.255.0
    Gateway IP Addr.................................. 10.125.18.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ Knowlogy Conference Rooms Side
    Cisco AP Group Name.............................. OGR
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.4.10.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. PoE/Medium Power (15.4 W)
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1252AG-A-K9
    AP Image......................................... C1250-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX122990L5
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 118
          WLAN 1 :........................................ 111
          WLAN 2 :........................................ 111
          WLAN 4 :........................................ 112
          WLAN 6 :........................................ 112
          WLAN 7 :........................................ 111
          WLAN 9 :........................................ 112
          WLAN 8 :........................................ 112
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 26 days, 00 h 24 m 39 s
    --More or (q)uit current module or <ctrl-z> to abort
    AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
    Join Date and Time............................... Wed Oct 9 10:59:07 2013
    Join Taken Time.................................. 0 days, 00 h 00 m 50 s
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211n-2.4
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 7
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:df:a5:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           11000 Kilo Bits.......................... MANDATORY
         MCS Set
           MCS 0.................................... SUPPORTED
           MCS 1.................................... SUPPORTED
           MCS 2.................................... SUPPORTED
           MCS 3.................................... SUPPORTED
           MCS 4.................................... SUPPORTED
           MCS 5.................................... SUPPORTED
           MCS 6.................................... SUPPORTED
           MCS 7.................................... SUPPORTED
           MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
           MCS 10................................... SUPPORTED
           MCS 11................................... SUPPORTED
           MCS 12................................... SUPPORTED
           MCS 13................................... SUPPORTED
           MCS 14................................... SUPPORTED
           MCS 15................................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
    --More or (q)uit current module or <ctrl-z> to abort
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 ..........

    Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
    Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
    There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
    Sent from Cisco Technical Support iPhone App

  • WLC upgrade license and access point

    Hi everyone,
    I need suggestion regarding wlc 5508  upgrade license. Right now i have 150 license for access points. There will be upgrade around 300 access points. So we are planning to buy new license until the maximum capacity of 5508 (500 licenses).
    Our management ip address is 192.168.50.x/24 . so all the access point are pointed to this management ip address (in the same subnet)
    First question,
    Because there will be an upgrade to around 450 access point. The current management ip address will not be enough.
    Please, give me the  best suggestion ?
    Should i create another management ip address ? or I need to make a bigger subnet using the current management ip address ?
    if i create a bigger ip address, the current access points must be set again yups ?
    Second question
    There will be a new link connected to the wlc, and i want to create new user subnets.
    what is the best practices for this matter ?
    if there are better suggestion, please let me know, i am still learning about wireless
    I have attached the topology.
    Thank you
    Fanie

    For an example, a 5508 can support up to 500 AP's, and the AP's can be in one large subnet or be in many different subnets and or even different locations. As long as the ap knows how to discover the WLC or the ap already had joined the WLC, then the AP's don't have to be on the same subnet as the WLC. The easiest way to have AP's join is to stage them on the same subnet as the WLC management and then move them to a different subnet. I would probably have no more than 100 AP's per subnet, but that's me. Stage some AP's on the management subnet that the WLC is on and then when the AP's join and complete downloading code, change the switch port Vlan and shut and no shut the port. The ap will come back up and join the WLC.
    Sent from Cisco Technical Support iPhone App

  • WLC 2106 comes up after rebooting

    Hello.
    I have installed a wlc2106 (ver 6.0.199.4).Everything was working fine until today...
    Wlc seems that looses connectivity with core switch (3750).That time i couldn't ping the management ip and i couldn't see it with cdp.
    After rebooting the controller the connectivity came up.The same situation was repeated after 30 minutes.
    I have attach the logs.
    Thanks.

    Hi,
    WLC port and the switchport will auto negotiate the speed/duplex...You need not hard code speed/duplex on the switchport...You may try resetting
    the switchport to defaults and configuring it again..for example,
    (config)# default interface
    (config)#int <>
    (config-if)#switchport trunk encapsulation dot1q
    (config-if)#switchport trunk allowed vlan x x x
    (config-if)#switchport mode trunk
    No need to set the native vlan on the switchport side if you have the tagging on the controller
    management interface...
    Once you make the above changes, reboot the WLC.
    Thanks,

  • WLC 2106 question

    Hello,
    What is the recomended way to connect  5 APs 1242 to a wlc 2106?
    Connect directly the 5 APs to the wlc and use one port for the management interface and connection to the switch or to connect the APs to a switch and use one connection for the wlc?
    Thanks in advance.

    Depends on the AP.
    One FastEthernet connection to the switch doens't "really" create a bottleneck.  Your AP might.  If you, say, you have 1130 or older then I'd say no significant bottleneck because the APs are also FastEthernet.
    If you use the newer ones, like the 1250 and newer, which has GigEthernet and/or higher throughput (if you enable 802.11n) the yes.  The switch AND the WLC 2100 are both the bottleneck.

  • Microsoft Server 2003 / PEAP / WLC 2106

    Has anyone ever had a certificate vanishing issue on an M$ Server 2003?  For some strange reason the certificate under my IAS RAS policy keeps disappearing after an undetermined amount of time?  The server is the only DC / CA root / IAS in the forest.  I'm not sure why the self-signed cert. will not remain in the cert. store?
    Current config.:
    (2) WLC 2106 (both RADIUS clients on DC/IAS)
    (5) 1141 LAPs
    Authentication: PEAP/MS-CHAPv2
    Encryption: TKIP/AES
    Any ideas?  Thanks.

    In 4.1, disabling DHCP proxy did just that, it disabled the "proxy". If you ever look at your dhcp lease of a wireless client, it comes from a dhcp server of 1.1.1.1 (virtual IP of the controller). With proxy disabled, the address will no longer be masked.
    In 4.2 and beyond, disabling dhcp proxy actually disables the DHCP Relay that is the process of the controller sending the dhcp requests to a specified server.
    So if in 4.1, you had "dhcp proxy" disabled, in 4.2 and beyond, you are actually disabling the relay as well.
    If this is indeed the case, enable dhcp proxy, or add an IP Helper adress to your router for this vlan, just like you would normally do for Wired clients.

Maybe you are looking for