WLC 2125 with 2x 1520 Mesh Points - Ethernet Bridging
Hi - I'm looking for assistance with a new Mesh set up we are deploying, the solutions consists of:
1x Wireless LAN Controller 2125
2x 1520 AP/Mesh Points
What we are trying to achieve is to bridge two networks together, I have followed the Cisco configuration guide and I simply can't get the traffic to cross from one side to the other. The WLC can see both 1520's on either side of the mesh network and I appear to have set it up right.
Here is how everything is set up:
- Local network (Class B, 10.0.0.0/16) connected to Port 1 on the WLC.
- 1520 is connected to Port 2 on the WLC via g0/0 with an IP address of 10.0.3.110 (management network, 10.0.3.111 for the wlan-management network) - this is set up as the RootAP, with ethernet bridging enabled and the bridging group set to rsqmesh.
- 2nd 1520 is around 800ft away set up as a MeshAP with ethernet bridging enabled and the bridging group set to rsqmesh. Small 5-port switch (non-cisco) connect to g0/0 on this 1520 with a device attached which has the IP of 10.0.3.37.
All help is appreciated.
Thanks,
Craig.
Bridging will not work if the RAP is directly connected to the controller. But CSCsk15792 is filed on this issue. If you put a switch between the controller and RAP traffic should start flowing.
Similar Messages
-
Outdoor Mesh AP Ethernet Bridging Problem
Hi All,
I've setup 6 X 1522 MESH APs.
Setup:
There is 1 RAP and the rest are MAPs. All APs have already successfully registered with the WLC (4402-50), with the RAP being the hub and all other MAPs a single hop away. APs are all in VLAN 10 (same vlan as the AP manager) and the WLC management interface is in VLAN 9. Bth VLANs are routable to each other. All APs are configured with Ethernet Bridging checked and all are configured with the same bridge group name. The switchports (Fa0/8) for each switch connected to each AP is configured to be trunk mode with native Vlan of 10. All switches are also configure with other VLANs such as VL20 - 30 besides the mentioned VL9 & 10.
Problem:We tried to bridge VLAN 20 across the wireless bridge by plugging a notebook(A) to a switchport (Fa0/1: sw mode access & sw ac vl 20) belonging to a switch connected to MAP1; and another notebook(B) also plugged in to a VL 20 access port whose switch is connected to the RAP. From notebook A, we were able to ping all relevant IP addresses (notebook B, WLC management IP, VL 20, VL30 ip addresses of equipment somewhere else in the network behind the RAP). This means the wireless bridge is already working as VL20 is already bridge across th MAP and RAP. However, when we tried to do anything else, such as ftp, IPERF, some other TCP dependent application, it doesn;t work. we setup a FTP server on notebook B and used notebook A to retrieve a file. ftp client in notebook A was able to perform login, list directory. But when a file is being pulled, it stopped after it downloaded exactly 1024byte of information. FTP will timeout after a while with only 1024byte transferred. However, using tftp, we were able to complete transferring the entire file. It seems that the wireless bridge or the switches which the hosts were connected to allows tftp (UDP) to go through but restricted big packets/blocks of TCP information to go through (since only file transfer or any other application involving larger data exchange fails, but logging in and telneting applications still works).
Very puzzled as we had previously configured wireless bridging before on the same model of APs and it was working.
Can any experts here offer any advise to our problem?
BTW, the WLC is on the latest version of the MESH firmware as of today. All APs gets their IP address dynamically from a router in VLAN 10 configured with the correct DHCP pool and option 43 parameters. DHCP should be working well as our APs are all registered with the correct range of IP addresses and all APs are pingable from anywhere in the network. LinkSNR between the RAP and the MAPs are very good ranging from 30-38 hence it should not be an issue of poor signal or interference or noise.
Thank you
AlvinI've personally not configured the MESH gear to form a bridge, so I can't provide any "real world" expertise. Here is short document on how to set it up, so maybe something within it will catch your eye:
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00808e9c1b.shtml
Good Luck! -
Mesh Ethernet Bridging with VLAN Tagging Issue
Hi all.
I'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again.
Has anyone else seen this? I can't find any relevant bugs.
JustinHi Saravanan,
It is one RAP and three MAPs. After a TAC call and 30 hours of monitoring, my VLANs have remained registered. I think the issue was mismatched VLANs to bridge groups an it looks like the mesh bridge may be stable for now. Here is what I was seeing on the RAP and MAPs when the VLANs were deregistering unexpectedly. Notice how VLANs 2 and 10 are mapped to opposite bridge groups on the RAP and MAP:
After I removed all the VLAN IDs from the Trunk configuration on the MAPs (through each AP's Mesh tab -- Ethernet Bridging config) and then rebuilt the VLAN IDs, I ran the same commands and now see this:
My very unscientific theory here is that the mismatching was causing consistency checks to fail, so the RAP was just tearing down the registrations after getting bogus or non- responses from the MAPs during the periodic VLAN registration maintenance checks (debug mesh ethernet registration).
If I have continued issues, I'll post back with updates.
Thanks for the response!
Justin -
Hi guys, I have a customer with a WLC 2125, with the version 6.0.199.4 and I will now upgrade to the version 7.0.250.0 but i wondering if it´s possible to make a backup for the old image, (i already download the configuration, but not the image) It´s is possible via console or web?
Or it´s safety do the upgrade directly?
Thanks
GonzaloHi,
As per my knowledge you can download old image from wlc. To get the same imgae its better to download from cisco.
Here is the link:
http://software.cisco.com/download/release.html?mdfid=282210723&flowid=7011&softwareid=280926587&release=7.0.250.0&relind=AVAILABLE&rellifecycle=ED&reltype=latest
Regards
Dont forget to rate helpful posts -
Hi guys, we are having some trouble with a WLC 2125 with only 6 APs, but like 40 clients trying to associate.
Version: 5.1.151.0
The issue here is that the WLC reboots every 6 or 8 hours for no apparent reason. CPU is always at 0% - 1% and mem usage is at 35% - 40%. I've heard in this forums that this kind of WLC is not recommended for more than 20 clients.. so I don't know if we are over using the box.
Maybe is an issue of software version or something, but in cisco.com there is only one version for this model of controller.
I'm adding an attachment with the crash file:
thanks!Reboots usually occur to one of three reasons on a 2100 series controller. First is power. The power supply is very susceptible to power spikes and brownouts. If the power spikes, the controller will reboot. Second, memory leaks on the controller. When using Web Auth the controllers CPU and memory resources are consumed fairly quickly. If the code does not effectively release those resources the system will eventually crash. There will be a record of this in the Tech Support section under management on the controller. Third and lastly, thermal issues around the controller. This will show in the event logs as a warning that the controller has exceeded it temperature threshold. If it gets too hot it will shut down completely.
We are just completing the largest single deployment of 2100 series controllers in Cisco's history deploying of 200 2125s and a number of other 2100 series controllers and these are the major reboot issues we have seen. -
Hello
I have set up an wlc 2125 with local eap auth which I think is working fine for now.
But I dont want it come up a certificate warning when user log in.
Can I stop this from happening without bying a certificate?
Can I turn of https all together?
TrondThank you Trond,
So here we are talking about web authentication, which does not use local EAP, so not sure whether the local EAP profile is really being triggered for that.
Clients are being prompted with a WLC's self-signed certificate, more or less in the same way as they would be if they tried to login to the WLC via HTTPS.
Similarly, the fastest way would be to install this certificate on the user's machine, so that it can trust it from that moment on.
Or you can generate a certificate signing request for the WLC, submit it to a root CA/buy a root CA signed server certificate (with the root CA trusted by the clients) and then install this certificate on the WLC:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00806e367a.shtml
For web authentication, there is no way to switch to HTTP for the WLC's certificate validation.
Regards,
Fede
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
Can you use a 3600 for an Ethernet bridge??
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
Can you use a 3600 for an Ethernet bridge??
http://www.cisco.com/en/US/docs/wireless/controller/7.0MR1/configuration/guide/cg_mesh.pdf
Check - Converting Indoor Access Points to Mesh Access Points
Ethernet bridging has to be enabled for the following two scenarios:
1. When you want to use the mesh nodes as bridges.
2. When you want to connect Ethernet devices such as a video camera on the MAP using its Ethernet port.
Wireless Backhaul:
In a Cisco wireless backhaul network, traffic can be bridged between MAPs and RAPs. This traffic can
be from wired devices that are being bridged by the wireless mesh or CAPWAP traffic from the mesh
access points.
Guidelines For Using Voice on the Mesh Network
• Voice is supported only on indoor mesh networks in release 5.2, 6.0, 7.0, and 7.0.116.0. For
outdoors, voice is supported on a best-effort basis on a mesh infrastructure.
other factors to note:-
#you would be running on backhaul using A radio which is prone to DFS.
#CAPWAP may not tolerent enough with AWPP convergence on MAP roaming.
#CAPWAP is more latency sensitive than voice. -
Can't get ethernet bridge to connect to network
Hi
I am trying to connect my old iMac G3 (10.2) to my airport express network with an Aeropad Mini (an ethernet bridge powered by USB hub on my mac - made by Macsense).
The network is seen successfully by an iMac G5, an Intel Macbook and a PC. The connection occasionally works but more often than not it does not see my airport express - instead it connects to a self-assigned IP. Sometimes it connects then drops off halfway through. Other times it just will not connect at all.
There are no drivers and you set it up via your browser. I can connect to the status and set-up page (192.168.1.50), after entering all the Aeropad info manually, and most times it can see my Airport Express (via the Site Survey on the set-up pages). but sometimes it does not even get that far. I reset the aeropad and restart the mac many times, and sometimes it works but mostly it doesn't.
I'm using channel 11 and it's WAP-encrypted.
Things I've tried:
updating the firmware from the macsense website
checking it's on client mode
manually entering the DNS address of my router - 10.0.1.1.
Trashing the internetconfig preferences from the library
making sure that ethernet is at the top of my network port configurations
Plugging it into a powered USB hub
Trying it on my MacBook (running Leopard).
Still can't connect - just a self-assigned IP - even on on the new macbook.
Any help would be appreciated as I really can't get this to work and it's beginning to take over my life!. I thought it was working after I entered the DNS address but it just went down again the next day.
Thanks.
Message was edited by: Joanna LeapmanThis is probably repeating the steps which you have taken already, but I thought I'd put them in one place just in case.
Problem:
If you're able to see other wireless networks but not your own. (And it works with AppleTV version 1.x)
It can be any of the following:
1. No wireless signal/out of range (check your multicast setting and put this as low as possible, check the range with other wireless devices/moving your appletv closer)
2. The wireless SSID is set to invisible/private (use "Other" on AppleTV and enter the SSID manually.)
3. The AppleTV doesn't support the channel used. (Tune the wireless to use a lower channel such as those under 10.)
4. The AppleTV is not supporting the security of your encryption.
Troubleshooting:
1. First try setting up a basic wireless network with no security, no frills such as a high multicast rate or high channel number and as a basic wireless b or g network. Position the AppleTV next to the basestation and then attempt to make the appletv connect to it. (Do not use an AdHoc network with your mac, as the AppleTV doesn't see these.) At this stage you're just trying to see if the AppleTV is even able to connect to your hardware. If this doesn't work there is possibly a larger problem at hand.
2. If this works, then move the devices to their desired locations. (This checks that it's not a range/interference issue.)
3. If this is still working, then the problem lays in a configuration setting. Firstly enable a security protocol, avoid WEP. Keep adding settings, keeping changes from the default to a minimum.
If you can't get past step 1, then it could be an issue with your wifi base station. Try getting the AppleTV to connect to a different wireless basestation (perhaps borrow one from a friend or a neighbour's unsecured network.) -
Hi all,
I'm running a 2106 with version 6.0.196.0. I'm running a couple indoor 1131s on it for regular client access successfully, but my problem is with trying to Ethernet Bridge Wireless Mesh two 1522s. I have placed the 1522 MAC addresses in the MAC Filter. I have Ethernet Bridging radio set on both the RAP and the MAP. I have the RAP and MAP connecting(They see each other as AWAPP neighbors, I can ping the MAP from the wired LAN, and it registers to the WLC, but I can't seem to bridge through these APs. I tried setting the Switchport attached to the RAP as an access port were the WLC and other APs sit as well as tried trunking it, making that same WLC vlan the native vlan. I also tried creating a separate AP group for the 1522s...no joy. Can anyone point me in the right direction on this?/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Indoor WLAN and outdoor mesh is not supported on the same WLC at the same time.
So you cannot mix 1131s and 1522s on the same controller.
Regards,
André -
Hello everybody,
I have a Mesh architecture with 2112 WLC and 1042 APs
I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
thanksHello benhamzagi,
Thank you for contacting the Sales Acceleration Center (SAC) regarding your recent inquiry, Case Number 80931
Case Description:
WLC 2112 with 1042 Mesh APs
Case Solution:
Here is the compatibility Matrix link
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp118661
Or the attach tables will help you base on Release, Controller, Mesh and AP
Table 3 Controller Software Release and Controller Model Support Matrix
Controller Model
First Support
Last Support
2100
4.2.x
7.0.x
2500
7.0.x
Cat3850
3.2.0SE
4400
4.2.x
7.0.x
5500
6.0.x
5700
3.2.0SE
7500
7.0.x
8500
7.3.x
Virtual Controller
7.3.x
WiSM
4.2.x
7.0.x
WiSM2 (1 DP)
7.0.x
WiSM2 (2 DP)
7.2.x
SRE
7.0.x
Table 4 Mesh and Controller Software Releases and the Supported APs
Mesh and Controller Releases
Supported Access Points
7.4.x
1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552EU, 1552CU, 1552S, 1130, 1240, 1250, 1260, 1600, 2600, 3500e, 3500i, 3500p, 3600e, 3600i, 1140, 600 OEAP, AP801, AP802
7.3.x
1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552EU, 1552CU, 1552S, 1130, 1240, 1250, 1260, 2600, 3500e, 3500i, 3600e, 3600i, 3500p, 1140, 600 OEAP, AP801, AP802
7.2.11x.x
1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552S, 1130, 1240, 1250, 1260, 2600, 3500e, 3500i, 3500p, 3600e, 3600i, 1140, 600 OEAP, AP801, AP802
7.2.10x.x
1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552S, 1130, 1240, 1250, 1260, 3500e, 3500i, 3600e, 3500p, 3600i, 1140, 600 OEAP, AP801, AP802
7.0.2x.x
1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1130, 1240, 1250, 1260, 3500e, 3500i, 3500p, 1140, 600 OEAP, AP801, AP802
7.0.116.0
1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1130, 1240, 1250, 1260, 3500e, 3500i, 3500p, 1140, 600 OEAP, AP801, AP802
7.0.98.x
1522, 1524PS, 1524SB, 1130, 1240
6.0.202.0
1522, 1524PS, 1524SB, 1130, 1240
5.2.193.0
1522, 1524PS, 1130, 1240
4.1.192.35M (Mesh Release 3)
1505, 1510, 1522, 1524PS, 1130, 1240
4.1.191.24M (Mesh Release 2)
1505, 1510, 1522 (US, Canada, and RoW), 1130, 1240
4.1.190.5 (Mesh Release 1)
1505, 1510, 1522 (US and Canada)
As per your confirmation, I am going to close the case for this specific inquiry. We strive to provide you with excellent service. Please feel free to reach out to me or any member of the SAC team if we can be of any further assistance or if you have any other related questions in the future. We value your input and look forward to serving you moving forward. -
Hello
I intend to connect a small network outside the main building by a mesh point to point link. In this small network are several vlan's in the ethernet network active. Is it possible to use the mesh point to point link as a trunk with tagged vlan's? If this not works, what alternativ exist?
Controller: WLC 2504
AP: 2602
Regards
PascalYes, this is possible. You will need to configure your RAP/MAP to peform "ethernet bridging".
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_mesh.html#wp1856051
Also, this section is regarding vlan tagging for your various interfaces.
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_mesh.html#wp1857978 -
3502p AccessPoint support MESH and Point-to-Point Wireless Bridging with Outdoor Antennas??
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging??
The 3502p is only used for arenas and or stadiums. These are different units than the 3500's and 3600's. So no they can't be.
You can use Cisco Aironet 1400 Series Wireless Bridge for a wireless link between two buildings (1km) to extend your LAN. For more detail you can go through the below link.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5279/ps5285/product_data_sheet09186a008018495c.html -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
Hi,
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.
I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.
The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
The RAP etherbridge port is enable and set to: normal
The MAP etherbridge port is enable and set to: Trunk,
native vlan is set to: 2
Vlan id 10
Vlan id 20
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
Could someone please tell me what I'm doing wrong?
I would open a TAC case as this is a bug. I don't recall what code it stopped working but I know it doesn't work also in the v7.3 & v7.4
Sent from Cisco Technical Support iPhone App -
Deployment of WLC-5508 with 2702i-D have performance issue.
Hi Team,
We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
1- HQ. have 26 AP with POWINJ5.
2- Branch location A- 8 AP with POWINJ5.
3. Branch location B have 8 AP with POWINJ4.
my exception is to achieve that single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
and branches are connected through flexconnect mode. and all are working with different-2 NPS.
Now i am facing a problem with this deployment are following.
1- branch A have performance issue.
2- HQ have performance issue.
3- i don't want to go with dedicated NPS for every location.
In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ.
kindly help me in that to understand where I am doing wrong things to achieve my expectation.
Thanks.
NalinI am facing 2 different problems.
1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet, that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group.
for more understanding please go through the below mentioned CLI view.
Cisco Controller) >show wlan apgroups
Total Number of AP Groups........................ 4
Site Name........................................ GURGAON-AP-GROUP
Site Description................................. GURGAON-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Pol icy
3 gurgaon-interface Disabled None
--More-- or (q)uit
4 gurgaon-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GUR-AP-01 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:e4 default location 1 IN 1
GUR-AP-05 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b5:18 default location 1 IN 1
GUR-AP-03 2 AIR-CAP2702I-D-K9 bc:16:65:13:71:00 default location 1 IN 1
GUR-AP-07 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:f8 default location 1 IN 1
GUR-AP-06 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:e0 default location 1 IN 1
GUR-AP-08 2 AIR-CAP2702I-D-K9 f4:4e:05:45:78:98 default location 1 IN 1
GUR-AP-02 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:2c default location 1 IN 1
GUR-AP-04 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:64 default location 1 IN 1
GUR-AP-09 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b4:44 default location 1 IN 1
Site Name........................................ MUMBAI-AP-GROUP
Site Description................................. MUMBAI-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
--More-- or (q)uit
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-7-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:d8 7th Floor 1 IN 3
--More-- or (q)uit
FAL-7-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:18 7th Floor 1 IN 1
FAL-7-AP14 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ad:e8 7th Floor 1 IN 1
FAL-7-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:4c 7th Floor 1 IN 1
FAL-7-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:bc 7th Floor 1 IN 1
FAL-7-AP13 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:80 7th Floor 1 IN 1
FAL-7-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:94 7th Floor 1 IN 1
FAL-7-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:e8 7th Floor 1 IN 1
FAL-7-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:f0 7th Floor 1 IN 3
FAL-7-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:e4 7th Floor 1 IN 1
FAL-7-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:84 7th Floor 1 IN 3
FAL-7-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:14 7th Floor 1 IN 1
FAL-7-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:c8 7th Floor 1 IN 3
FAL-7-AP11 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:08 7th Floor 1 IN 1
Site Name........................................ MUMBAI-THIRD-FLOOR-AP
Site Description................................. MUMBAI-THIRD-FLOOR-AP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
--More-- or (q)uit
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-3-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:a4 3rd Floor 1 IN 3
FAL-3-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:94 3rd Floor 1 IN 3
FAL-3-AP11 2 AIR-CAP2702I-D-K9 f4:0f:1b:73:00:74 3rd Floor- Eurek 1 IN 3
FAL-3-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:d0 3rd Floor 1 IN 3
--More-- or (q)uit
FAL-3-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b5:88 3rd Floor 1 IN 3
FAL-3-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:9c 3rd Floor 1 IN 3
FAL-3-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:af:a0 3rd Floor 1 IN 1
FAL-3-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:fc 3rd Floor- Eurek 1 IN 3
FAL-3-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:28 3rd Floor 1 IN 3
FAL-3-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:f4 3rd Floor 1 IN 3
FAL-3-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:8c 3rd Floor 1 IN 2
FAL-3-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:f4 3rd Floor 1 IN 3
Site Name........................................ RAHEJA-AP-GROUP
Site Description................................. RAHEJA-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
--More-- or (q)uit
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
5 raheja-interface Disabled None
2 raheja-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-RAHEJA-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:1c Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:37:3c Confrennce Room 1 IN 3
FAL-RAHEJA-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:48 Near Confrence R 1 IN 3
FAL-RAHEJA-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:c0 Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:a0 Near Server Room 1 IN 3
FAL-RAHEJA-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:20 Reception Area 1 IN 3
FAL-RAHEJA-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:68 USER BAY ROAD si 1 IN 1
FAL-RAHEJA-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:d4 Training Room 1 IN 1
--More-- or (q)uit
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
3 gurgaon-interface Disabled None
4 gurgaon-guest Disabled None
5 raheja-interface Disabled None
6 test Disabled None
Cisco Controller) >show flexconnect group summary
FlexConnect Group Summary: Count: 4
Group Name # Aps
Gurgaon-AP 9
HQ-3RD-FLR-AP-GROUP 12
HQ-7THFLR-AP-GROUP 14
Raheja-AP-Group 8
(Cisco Controller) >show flexconnect group detail Gurgaon-AP
Number of AP's in Group: 9
bc:16:65:13:71:00 GUR-AP-03 Joined Flexconnect
f4:4e:05:45:78:98 GUR-AP-08 Joined Flexconnect
f4:4e:05:78:ae:64 GUR-AP-04 Joined Flexconnect
f4:4e:05:78:ae:e4 GUR-AP-01 Joined Flexconnect
f4:4e:05:80:b3:2c GUR-AP-02 Joined Flexconnect
f4:4e:05:80:b3:e0 GUR-AP-06 Joined Flexconnect
f4:4e:05:80:b3:f8 GUR-AP-07 Joined Flexconnect
f4:4e:05:80:b4:44 GUR-AP-09 Joined Flexconnect
f4:4e:05:80:b5:18 GUR-AP-05 Joined Flexconnect
Efficient AP Image Upgrade ..... Disabled
Master-AP-Mac Master-AP-Name Model Manual
Group Radius Servers Settings:
Type Server Address Port
Primary Unconfigured Unconfigured
Secondary Unconfigured Unconfigured
--More-- or (q)uit
Group Radius AP Settings:
AP RADIUS server............ Disabled
EAP-FAST Auth............... Disabled
LEAP Auth................... Disabled
EAP-TLS Auth................ Disabled
EAP-TLS CERT Download....... Disabled
PEAP Auth................... Disabled
Server Key Auto Generated... No
Server Key.................. <hidden>
Authority ID................ 436973636f0000000000000000000000
Authority Info.............. Cisco A_ID
PAC Timeout................. 0
Multicast on Overridden interface config: Disabled
DHCP Broadcast Overridden interface config: Disabled
Number of User's in Group: 0
Vlan :........................................... 203
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 205
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 204
--More-- or (q)uit
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 206
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 207
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 208
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 209
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 210
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 211
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 212
Ingress ACL :................................... None
Egress ACL :.................................... None
--More-- or (q)uit
Vlan :........................................... 216
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 217
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 218
Ingress ACL :................................... None
Egress ACL :.................................... None
Group-Specific FlexConnect Wlan-Vlan Mapping:
WLAN ID Vlan ID
WLAN ID SSID Central-Dhcp Dns-Override Nat-Pat
(Cisco Controller) >
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 6
WLAN ID WLAN Profile Name / SSID Status Interface Name PMIPv6 Mobility
1 FRACTAL-EMP-MUMBAI / FRACTAL Enabled group for mumbai none
2 FRACTAL-GUEST / FRACTAL-GUEST Enabled guest wifi none
3 FRACTAL-EMP-GURGAON / FRACTAL-GURGAON Enabled gurgaon-interface none
4 GURGAON-GUEST / FRACTAL-GUEST-GURGAON Enabled gurgaon-guest none
5 RAHEJA-EMP-WIRELESS / FRACTAL-R Enabled raheja-interface none
6 TEST-SSID / TEST-SSID Enabled test none
hope this will give you proper understanding.
Maybe you are looking for
-
Windows 7 x64 bit and iTunes not recognizing iPhone 3GS
Hello, I'm sorry to bring this up again and I know the community has seen it a million times but I'm definately needing someone to point me in the right direction. I have an Acer 5552 Laptop with Windows 7 x64 bit. It does not have the Intel P55 chip
-
Connecting two routers to create a home network and have access to the net "wired"
How do i set up a network between two linksys routers that can access the internet and computers set up on both routers. I noticed I cannot browse our home network computers that are behind the other router. currently i have a net connection going to
-
Unable to update my mac software
Hi, I am unable to update my macbook pro software. It says restart required. After restarting nothing happens and the system still shows one update pending. Please help me on the same. Thanks,
-
Displaying time ranges as a separate column
Hi, I need to show the time ranges with 30minutes starting from today 12:00 AM till current timestamp showing the time range as Time Interval 0:01 AM - 0:30 AM 0:31 AM - 1:30 AM till current timestamp(4:30 PM-5:00PM) as a separate column. Have anyone
-
I just upgraded to CS6 and Lightroom 4.2. LR4.2 sends photos to CS4, which I not longer have (nothing happens when I hit "Edit In"). How do I get LR 4.2 to send photos to be edited in CS6?