WLC2412-Clients Not receiving DHCP addresses
I recently upgraded a clients WLC and they keep saying they are unable to get an IP address from the DHCP server. It's a simple, flat network and here is what the logs are showing. Any advice would be greatly appreciated.
*apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
(Cisco Controller) show>interface detailed management
Interface Name................................... management
MAC Address...................................... 64:00:f1:91:5d:40
IP Address....................................... 192.168.8.3
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.8.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 8
Quarantine-vlan.................................. 0
Physical Port.................................... 1
Primary DHCP Server.............................. 192.168.8.49
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Similar Messages
-
Clients not receiving DHCP IP address from HREAP centrally Switched Guest SSID
Hi All,
I am facing a problem in a newly deployed branch site where the Clients are not receiving DHCP IP address from a centrally switched Guest SSID. I see the client status is associated but the policy manager state is in DHCP_REQD.
The dhcp pool is configured on the controller itself. The local guest clients are able to get DHCP and all works fine, the issue is only with the clients in the remote site. The Hreap APs are in connected mode. Could you please suggest what could be the problem. Below is the out of the debug client.
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Adding mobile on LWAPP AP 3c:ce:73:6d:37:00(1)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Reassociation received from mobile on AP 3c:ce:73:6d:37:00
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Changing ACL 'Guest-ACL' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Applying site-specific IPv6 override for station 10:40:f3:91:7e:24 - vapId 17, site 'APG-MONZA', interface 'vlan_81'
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Applying IPv6 Interface Policy for station 10:40:f3:91:7e:24 - vlan 81, interface id 13, interface 'vlan_81'
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Applying site-specific override for station 10:40:f3:91:7e:24 - vapId 17, site 'APG-MONZA', interface 'vlan_81'
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 3c:ce:73:6d:37:00 vapId 17 apVapId 1
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
*apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 apfMsAssoStateInc
*apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 apfPemAddUser2 (apf_policy.c:222) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Idle to Associated
*apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 Scheduling deletion of Mobile Station: (callerId: 49) in 28800 seconds
*apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 Sending Assoc Response to station on BSSID 3c:ce:73:6d:37:00 (status 0) ApVapId 1 Slot 1
*apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 apfProcessAssocReq (apf_80211.c:4672) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Associated to Associated
*apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4183, Adding TMP rule
*apfReceiveTask: May 24 11:35:53.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 3c:ce:73:6d:37:00, slot 1, interface = 13, QOS = 3
ACL Id = 255, Jumbo F
*apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 IPv6 Vlan = 81, IPv6 intf id = 13
*apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (ACL ID 255)
*pemReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 Sent an XID frame
*apfMsConnTask_3: May 24 13:26:49.401: 10:40:f3:91:7e:24 Updating AID for REAP AP Client 3c:ce:73:6d:37:00 - AID ===> 1
*apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) DHCP Policy timeout
*apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Pem timed out, Try to delete client in 10 secs.
*apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 Scheduling deletion of Mobile Station: (callerId: 12) in 10 seconds
*osapiBsnTimer: May 24 13:28:59.315: 10:40:f3:91:7e:24 apfMsExpireCallback (apf_ms.c:599) Expiring Mobile!
*apfReceiveTask: May 24 13:28:59.315: 10:40:f3:91:7e:24 apfMsExpireMobileStation (apf_ms.c:4897) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Associated to Disassociated
*apfReceiveTask: May 24 13:28:59.315: 10:40:f3:91:7e:24 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
*osapiBsnTimer: May 24 13:29:09.315: 10:40:f3:91:7e:24 apfMsExpireCallback (apf_ms.c:599) Expiring Mobile!
*apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 Sent Deauthenticate to mobile on BSSID 3c:ce:73:6d:37:00 slot 1(caller apf_ms.c:4981)
*apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 apfMsAssoStateDec
*apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 apfMsExpireMobileStation (apf_ms.c:5018) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Disassociated to Idle
*apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Deleted mobile LWAPP rule on AP [3c:ce:73:6d:37:00]
*apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 Deleting mobile on AP 3c:ce:73:6d:37:00(1)
*pemReceiveTask: May 24 13:29:09.317: 10:40:f3:91:7e:24 0.0.0.0 Removed NPU entry.#does the client at the remote site roams between AP that connects to different WLC?
#type 9 is not good.
*pemReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
#Does your dhcp server getting hits.
#Also, get debug dhcp message & packet.
#Dhcp server is not responding.
*apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) DHCP Policy timeout
*apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Pem timed out, Try to delete client in 10 secs. -
Client not receive ip address - dhcp_reqd
Hi,
In my environment there's a 5508 (firmware 7.4.110.0) and ap 1600 with a ias radius server. All wlan are in flex-connect local switching, one client try to connect on a wlan but not receive ip address. After enabled debug aaa all i took the log corresponding :
Cisco Controller) >*emWeb: Feb 11 16:52:36.047: Created WARP Capabilities IE (length 12) for WLAN LAB
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Adding mobile on LWAPP AP 00:3a:9a:77:55:a0(0)
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Association received from mobile on BSSID 00:3a:9a:77:55:06
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Rf profile 200 Clients are allowed to AP radio
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Max Client Trap Threshold: 50 cur: 3
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Rf profile 200 Clients are allowed to AP wlan
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Re-applying interface policy for client
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
*apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 In processSsidIE:4264 setting Central switched to FALSE
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying site-specific Local Bridging override for station 18:3d:a2:25:01:a4 - vapId 103, site 'Test', interface 'management'
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying Local Bridging Interface Policy for station 18:3d:a2:25:01:a4 - vlan 0, interface id 0, interface 'management'
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying site-specific override for station 18:3d:a2:25:01:a4 - vapId 103, site 'Test', interface 'management'
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Re-applying interface policy for client
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Processing WPA IE type 221, length 24 for mobile 18:3d:a2:25:01:a4
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 8
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 unsetting PmkIdValidatedByAp
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) DHCP required on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1for this client
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1 flex-acl-name:
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfMsAssoStateInc
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 18:3d:a2:25:01:a4 on AP 00:3a:9a:77:55:a0 from Idle to Associated
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfPemAddUser2:session timeout forstation 18:3d:a2:25:01:a4 - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Sending Assoc Response to station on BSSID 00:3a:9a:77:55:a0 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfProcessAssocReq (apf_80211.c:7399) Changing state for mobile 18:3d:a2:25:01:a4 on AP 00:3a:9a:77:55:a0 from Associated to Associated
*apfMsConnTask_2: Feb 11 16:54:22.506: 18:3d:a2:25:01:a4 Updating AID for REAP AP Client 00:3a:9a:77:55:a0 - AID ===> 4
*dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 Station 18:3d:a2:25:01:a4 setting dot1x reauth timeout = 1800
*dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Connecting state
*dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 Sending EAP-Request/Identity to mobile 18:3d:a2:25:01:a4 (EAP Id 1)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 Received EAPOL START from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Connecting state
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 Sending EAP-Request/Identity to mobile 18:3d:a2:25:01:a4 (EAP Id 2)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.541: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.541: 18:3d:a2:25:01:a4 Received EAP Response packet with mismatching id (currentid=2, eapid=1) from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Received Identity Response (count=2) from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 EAP State update from Connecting to Authenticating for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Authenticating state
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=3) for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 3)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 3, EAP Type 25)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=4) for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 4)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 4, EAP Type 25)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=7) for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 WARNING: updated EAP-Identifier 4 ===> 7 for STA 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 7)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 7, EAP Type 25)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Processing Access-Accept for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Station 18:3d:a2:25:01:a4 setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Username entry (pippo) created for mobile, length = 253
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Username entry (pippo) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Creating a PKC PMKID Cache entry for station 18:3d:a2:25:01:a4 (RSN 0)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Sending EAP-Success to mobile 18:3d:a2:25:01:a4 (EAP Id 7)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Freeing AAACB from Dot1xCB as AAA auth is done for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Starting key exchange to mobile 18:3d:a2:25:01:a4, data packets will be dropped
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Entering Backend Auth Success state (id=7) for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Received Auth Success while in Authenticating state for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Authenticated state
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Received EAPOL-key in PTK_START state (message 2) from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 apfMs1xStateInc
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1for this client
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1 flex-acl-name:
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5952, Adding TMP rule
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 00:3a:9a:77:55:a0, slot 0, interface = 13, QOS = 0
IPv4 ACL ID = 255, IP
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 0, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 Key exchange done, data packets from mobile 18:3d:a2:25:01:a4 should be forwarded shortly
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
*pemReceiveTask: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask3: Feb 11 16:54:22.707: 18:3d:a2:25:01:a4 Sent EAPOL-Key M5 for mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.768: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.768: 18:3d:a2:25:01:a4 Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile 18:3d:a2:25:01:a4
*Dot1x_NW_MsgTask_4: Feb 11 16:54:22.769: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
*apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5576, Adding TMP rule
*apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 00:3a:9a:77:55:a0, slot 0, interface = 13, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 0, Local Bridging intf id = 0
*apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*pemReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
(Cisco Controller) >*emWeb: Feb 11 16:54:46.127: 18:3d:a2:25:01:a4 Central Switch = FALSE
*emWeb: Feb 11 16:54:46.128: 18:3d:a2:25:01:a4 Central Switch = FALSE
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >*emWeb: Feb 11 16:55:36.461: 18:3d:a2:25:01:a4 Central Switch = FALSE
*emWeb: Feb 11 16:55:36.463: 18:3d:a2:25:01:a4 Central Switch = FALSE
From log i know that 802.1x passed, while dhcp don't send ip address. It seems that the local vlan id is 0 while in reality is 3... WHY ? i don't understand.
Someone can help me to find the problem? i think the problem is on the network, the dhcp ( the corporate router) is directly connected to the ap.Are you setting your FlexConnect native vlan and the wlan to vlan mapping? You also need to make sure you have the ip helpers setup and that dhcp is working. I would configure a switch port to a vlan that the wireless users is suppose to be on locally at that site and connect a laptop to that port and make sure that the laptop gets an address.
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"***** -
WLC2504 clients not receiving DHCP leases
I'm stock with a 2504 using version 7.0.220.0 that won't lease out DHCP adresses
Wifi clients are unable to get a DHCP lease from an external DHCP server.
The WLC are handling 3 WLAN, 2 using internal DHCP server, 1 (that wont work) using external DHCP. The external DHCP server, is a router/firewall (out of my reach) that suffered from a power out, a short while ago, ever since the DHCP is not working on that VLAN, if client are getting static ip adresses, everything works fine. If i'm using the same network link, and plug it into a computer, I get a DHCP address.
I've enable DHCP proxy
Debbuging DHCP, using: Debug DHCP packets enable
Gives me this:
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP received op BOOTREQUEST (1) (len 308,vlan 20, port 1, encap 0xec00)
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option len (including the magic cookie) 72
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: message type = DHCP INFORM
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 61 (len 7) - skipping
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 12 (len 1) - skipping
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: vendor class id = MSFT 5.0 (len 8)
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 55 (len 13) - skipping
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP options end, len 72, actual 64
*DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
ThanksHi Steen,
When a client is in DHCP REQ state on the controller, the controller drops DHCP inform packets. The client will not go into a RUN state on the controller (this is required for the client to pass traffic) until it receives a DHCP discover packet from the client. DHCP inform packets are forwarded by the controller when DHCP proxy is disabled.
Please check this, if still u r facing issue then provide more info.
Can you please paste a client debug of the client having DHCP issues.
Go to cli of the wlc and run the client debug . Diconnect the client then reconnect and gather the output and post.
Regards -
Clients not receiving DHCP on layer 2 Vlan
I have flexconnect WAPs with local switching and local dhcp server on the switch.
I have one SSID assigned to a layer 2 vlan. The wireless clients are unable to receive an ip address on this vlan. The wired clients are able to receive an ip address on this vlan with no problem.
The WAP switchport is trunked and all of the layer 3 vlans are working with no problem.
The layer 2 vlan interface is assign the DHCP - ip address pool Vendor_VLan
Any help would be appreciated.
Thanks
LHHi LH,
Have you configured the SSID with "Local Switching" feature.
Also did you do the vlan mapping on this FlexConnect AP for the configured SSID ?
HTH
Rasika
**** Pls rate all useful responses **** -
Vmware clients not receiving dhcp from wifi networks
we are testing mac laptops running windows 7 virtually using vmware fusion at our office. One problem i ran into is windows 7 cant ever get the dhcp information from Domain Controller to get onto the network/internet here at the office. i have set the NIC to bridged mode in vmware fusion. it works fine at my house where i can get on my home network/internet just not in the office so i know it can be done, but not sure what setting on the cisco wireless lan controller 2106 controlls that feature. can anyone assist me in resolving this? if i plug it into the network using an ethernet cable everything works just fine, so i believe it is just a setting on the wireless controller that needs to be changed, at least thats what i am hoping, im hoping its not some limitation of the system......
Hi,
I thought i replied to this post.. but i havent.. extremly sorry!! here is the bug that we are hitting!!
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsi90344
There are workarounds to overcome this..
Workarounds: 1. Configure the virtual machine software for NAT ("shared networking") mode, not bridged mode. 2. If using 4.1 WLC software, configure the virtual machine to use static IP addressing, not DHCP. 3. If you have an AP that does H-REAP, change the AP mode to H-REAP and local switching so that DHCP (and other) packets do not traverse the controller.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull -
Clients not receiving dchp addresses from server
Our dhcp server (windows 2012) is failing to issues addresses to the pc's. Once the lease has expired on the pc (user goes on holiday for a week) the machine will fail to pick up an ip address on the users return.
The event viewer on the server reads "IP address range of scope is 95 percent full with only 7 IP address available"
I have gone through the dhcp scope of which there are 94 exclusions and i have a further 39 machines which require addresses.
On a class C subnet i should have far more than 7 addresses available.
Any thoughts as to what might be at fault here.
This topic first appeared in the Spiceworks CommunityJust completed a major network upgrade... So decided it was time to stack some ofmy old switches! Can anyone date some of these things?And some before and after shots: The first one is of a distribution cabinet (2 x 10Gig Fiber link ag. to server room) on the other side of our site, the last two are of the core cabinet in my server room. Will take some more pictures later.
-
Clients not receiving addresses from DHCP
I have a Cisco 2811 router and have configured it to be a DHCP server at a remote site. It seems like it should be pretty straight forward to configure DHCP. Apparently I'm missing something because I can't get clients to receive an address. Below are the applicable parts of the config. I also have tried associating the DHCP pool with the Claims vrf and that did not work either.
ip dhcp excluded-address 10.10.30.0 10.10.30.99
ip dhcp excluded-address 10.10.30.201 10.10.30.255
ip dhcp pool Claims_Office
network 10.10.30.0 255.255.255.0
domain-name fmi.com
default-router 10.10.30.253
dns-server 10.10.10.191
lease 7
interface FastEthernet0/0
description Claims Office
vrf forwarding Claims
ip address 10.10.30.253 255.255.255.0
duplex auto
speed auto
no mop enabled
interface FastEthernet0/0/0.1205
description Claims Office
vrf forwarding Claims
encapsulation dot1Q 1205
ip address 192.168.103.2 255.255.255.252Unfortunately that didn't work. Here is the output before:
Pool Claims_Office :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 254
Leased addresses : 0
Pending event : none
1 subnet is currently in the pool :
Current index IP address range Leased addresses
10.10.30.1 10.10.30.1 - 10.10.30.254 0
And after:
Pool Claims_Office :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 254
Leased addresses : 0
Pending event : none
1 subnet is currently in the pool :
Current index IP address range Leased addresses
10.10.30.1 10.10.30.1 - 10.10.30.254 0
What I want is for it to assign addresses from 10.10.30.100-199 -
Flexconnect Local Switching Hosts Do Not Receive IP Addresses
Hello,
My WLC software version is 7.4.110.0. I have a branch office in my lab. The AP in my branch is configured as flexconnect with native VLAN of 700. The SSID that I have in the branch office is configured to do local switching. The show wlan is added below.
My tunneled SSID still working and I can still receive IP addresses from it. My issue is last week I have the Flexconnect working with no problem, then this morning I can connect to the SSID, but I'm not receiving IP addresses for my test wireless clients.
Thanks
[code]
WLAN Identifier.................................. 2
Profile Name..................................... ACS Guest
Network Name (SSID).............................. RMTGuest
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
--More-- or (q)uit
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... RK2WLC5508-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... 172.28.27.130
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
PMIPv6 Mobility Type............................. none
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
--More-- or (q)uit
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
--More-- or (q)uit
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
--More-- or (q)uit
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
--More-- or (q)uit
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
[/code]is the VLAN still mapped on the AP, and allowed across the trunk?
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
1142 Autonomous AP not passing DHCP address to clients
Hi there,
I do hope someone can help me out here because I am having a nightmare with a single AP.
Setup is as follows:
5 existing APs already on site, all working correctly plugged into a 48 port 2960, (non poe).
customer wants to add another AP to extend capacity.
Installed AP, (config attached) mirrored switchport settings, (below) and fired it up.
Outcome: if you are on a static IP or have received DHCP through another AP then everything works as it should. But DHCP requests are never fulfilled if connected through this AP. (this goes also for a laptop with an existing DHCP address if you go through the \release \renew process) DHCP is served by a server living on the switch.
The AP lives on VLAN 2, hence native .2 on both ends, and wireless clients should recieve a VLAN 1 address. All the other APs, (1131s) are working without a problem and this is driving me NUTS! Have been through configs and every screen of the GUI but cant find any difference in set up. Apart from different AP models the new one is on a pwrinj4 while the others are on pwrinj3's.
Switchport settings:
interface GigabitEthernet0/1
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
AP Config
aaa authentication login default local
aaa authentication enable default enable
aaa authorization exec default local
aaa authorization network default local
aaa session-id common
dot11 vlan-name *** vlan 1
dot11 vlan-name *** vlan 2
dot11 ssid ***
vlan 1
authentication open
authentication key-management wpa optional
wpa-psk hex ***
username manager privilege 15 password ***
username user privilege 0 password ***
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 2 size 128bit *** transmit-key
encryption mode ciphers tkip wep128
encryption vlan 1 key 2 size 128bit *** transmit-key
encryption vlan 1 mode ciphers tkip wep128
ssid ***
channel 1
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption key 2 size 128bit *** transmit-key
encryption mode ciphers tkip wep128
encryption vlan 1 key 2 size 128bit *** transmit-key
encryption vlan 1 mode ciphers tkip wep128
ssid ***
no dfs band block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio1.2
encapsulation dot1Q 2 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface GigabitEthernet0.2
encapsulation dot1Q 2 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
transport preferred all
transport output all
line vty 0 4
transport preferred all
transport input all
transport output all
line vty 5 15
transport preferred all
transport input all
transport output all
interface dot11Radio 0
ssid ***
no shutdown
interface dot11Radio 1
ssid ***
no shutdown
power inline negotiation injector installed
interface BVI1
ip address 10.25.97.245 255.255.255.0
no ip route-cache
ip default-gateway 10.25.97.1Hi Scott,
Yes, the only difference is as this is a 1142 I was instructed to put it onto one fo the Gb ports. I tried the Ap on a known working port to rule out switch config to no effect.
Here is the extended switch config:
interface FastEthernet0/44
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/45
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/46
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/47
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/48
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface GigabitEthernet0/1
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
interface FastEthernet0/44
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/45
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/46
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/47
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/48
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
spanning-tree portfast
interface GigabitEthernet0/1
description Connect to wireless AP
switchport trunk native vlan 2
switchport trunk allowed vlan 1,2,1002-1005
switchport mode trunk
Not sure about the spanning tree settings on the others: I didnt set those up and am a great believer in the "if it aint broke, dont fix it" maxim! -
DHCP: Some clients not getting IP address
Recently setup a new DHCP server on Mac OS X Server 10.5.8 running on an Xserve. We migrated from a Linux server.
The Xserve was originally just a file server. So the only services currently running are: AFP, DHCP, NFS, and SMB. No additional software is running.
The DHCP server ran just fine for the first couple weeks. But then we found some computers just stopped getting IP addresses from the DHCP server. Some were new computers introduced to the network. Some were laptops that had left and come back. However, the DHCP server is definitely still giving out IP addresses and renewing them for most new and existing computers. There have been five computers that have not gotten IP addresses so far, and that had been the case both on the wireless and on a wired connection. Two were PC's, one running Windows 7 and one running Windows XP with Lenovo's ThinkVantage software. The other three were different models of MacBook Pros.
For those five computers, we managed to get them working in two ways. One, we can select to use DHCP with a manual address. When we do that, it manages to pick up all the other information from the DHCP server like DNS and gateway. The second thing we can do is configure the DHCP server to supply a static IP address by providing it with the MAC address of these machines. When we do that, the computers receive the IP address from the DHCP server.
So I guess you could say the problem I'm experiencing is for a few computers the DHCP server seems to only be able to provide static addresses, but not dynamic ones with a lease time.
I have logging set to the highest for the DHCP server. Below is the first thing I noticed that keeps showing up. Sometimes it shows a different MAC address than the one below. None of the afflicted computers have that MAC address, though. I have not seen any other errors in the logs for the DHCP server.
Jan 24 12:09:47 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:09:47 fileserver bootpd[73839]: service time 0.000304 seconds
Jan 24 12:09:50 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:09:50 fileserver bootpd[73839]: service time 0.000280 seconds
Jan 24 12:09:54 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:09:54 fileserver bootpd[73839]: service time 0.000264 seconds
Jan 24 12:10:03 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:03 fileserver bootpd[73839]: service time 0.000265 seconds
Jan 24 12:10:11 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:11 fileserver bootpd[73839]: service time 0.000283 seconds
Jan 24 12:10:19 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:19 fileserver bootpd[73839]: service time 0.000291 seconds
Jan 24 12:10:28 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:28 fileserver bootpd[73839]: service time 0.000324 secondsRecently setup a new DHCP server on Mac OS X Server 10.5.8 running on an Xserve. We migrated from a Linux server.
The Xserve was originally just a file server. So the only services currently running are: AFP, DHCP, NFS, and SMB. No additional software is running.
The DHCP server ran just fine for the first couple weeks. But then we found some computers just stopped getting IP addresses from the DHCP server. Some were new computers introduced to the network. Some were laptops that had left and come back. However, the DHCP server is definitely still giving out IP addresses and renewing them for most new and existing computers. There have been five computers that have not gotten IP addresses so far, and that had been the case both on the wireless and on a wired connection. Two were PC's, one running Windows 7 and one running Windows XP with Lenovo's ThinkVantage software. The other three were different models of MacBook Pros.
For those five computers, we managed to get them working in two ways. One, we can select to use DHCP with a manual address. When we do that, it manages to pick up all the other information from the DHCP server like DNS and gateway. The second thing we can do is configure the DHCP server to supply a static IP address by providing it with the MAC address of these machines. When we do that, the computers receive the IP address from the DHCP server.
So I guess you could say the problem I'm experiencing is for a few computers the DHCP server seems to only be able to provide static addresses, but not dynamic ones with a lease time.
I have logging set to the highest for the DHCP server. Below is the first thing I noticed that keeps showing up. Sometimes it shows a different MAC address than the one below. None of the afflicted computers have that MAC address, though. I have not seen any other errors in the logs for the DHCP server.
Jan 24 12:09:47 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:09:47 fileserver bootpd[73839]: service time 0.000304 seconds
Jan 24 12:09:50 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:09:50 fileserver bootpd[73839]: service time 0.000280 seconds
Jan 24 12:09:54 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:09:54 fileserver bootpd[73839]: service time 0.000264 seconds
Jan 24 12:10:03 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:03 fileserver bootpd[73839]: service time 0.000265 seconds
Jan 24 12:10:11 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:11 fileserver bootpd[73839]: service time 0.000283 seconds
Jan 24 12:10:19 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:19 fileserver bootpd[73839]: service time 0.000291 seconds
Jan 24 12:10:28 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
Jan 24 12:10:28 fileserver bootpd[73839]: service time 0.000324 seconds -
DHCP via Hyper-V VM, Server2012r2 Hyper-V host, clients not getting IP address
You have to authorize a dhcp server as Britv8 says. That's the only way it'll start dishing out leases. That's standard for Windows DHCP server in an AD Domain.
Also there's 0 reason to mention Hyper-V here. The whole point of virtualization is to do hardware level abstraction.I recently encountered this. Setup:
Initial setup of the system was at a different location from its final destination, with different network equipment (switches) between the two. No teaming is involved, however.
Set up the system at its final destination, with DHCP via a Hyper-V VM (Server2012r2), Server2012r2 Hyper-V host, physical clients on the lan were not getting IP address.
The physical server box has a 4-port Intel Gigabit ethernet card.
I moved the setup (Hyper-V Virtual Switch manager) so that the interface for the DHCP server VM was isntead using one of two built-in Broadcom adapters.
While this topic seemed promising,
http://community.spiceworks.com/topic/251317-hyper-v-vm-not-leasing-ip-s-dhcp
unfortunately, "fiddling about" was not what I was looking for as possible solution.
My notes for the resolution:
Hyper-V system running...
This topic first appeared in the Spiceworks Community -
Clients not getting DHCP from external server
Hi,
I have a 4402 (version 7.0.235) working with 10 units of 1121 APs connected to it. The WLC is not configured to work in LAG mode. Physical portt #1 is connected to the Main Switch (trunk). I have 3 WLAN mapped to 3 Different VLAN and Everything (security and internal, external DHCP) is working swell...
Now- I have connected Physical port #2 directly to an ADSL Router (giga port), Configured Port 2 as untaggedwith the proper IP details.
I have configured this interface to receive DHCP from the ADSL Router and for some reason, Clients are not getting addresses.
When I assign a Static address to my laptop I get internet access and all is nice. I tried configuring The WLC internal DHCP server (instead of the ADSL router) and that didn't help. It seems like a DHCP problem but I dont understand the source of the problem of think of the solution.
When turning off the proxy settings I noticed that it helped. Is there anything to do with that? The problem was that after a while the other WLANs starting causing DHCP issues as well.
What is supposed to be configured? Any Expert is the House?
I attached a crappy drawing..Hi Scott,
Thanks for your answer.
So what you are basicly saying is that I have 2 choices: 1 - disable the Proxy option on the WLC and work with external DHCP servers (internal will not work when this is enabled). 2 - Enable the Proxy option and only work with the WLC internal DHCP.
I have installed many WLCs this way, having Different DHCP Servers (external and internal) for multiple WLANs.
What do you think may be different this time? The router that I am using isn't the most expencive but it is providing DHCP to other clients (wired client) with no problems.
Thanks!!! -
Clients not getting DHCP in VRF
Good morning -
We have devices in the global routing table (not in a VRF) getting DHCP addresses without issue. The SVI is configured as such:
interface Vlan2301
description BLUE
ip address 172.19.68.1 255.255.255.0
ip helper-address 10.4.16.222
interface Vlan2512
description RED
vrf forwarding RED
ip address 10.217.5.1 255.255.255.0
ip helper-address 10.4.16.222
Clients in BLUE are getting DHCP but clients in RED are not. If I statically assign an address I have connectivity and can reach the DHCP server (which is also DNS server; with a static IP in VLAN 2512 I can do name resolutions for example).
I am at a bit of a loss. Is there anything special I need to do for VRF IP HELPER-ADDRESS configuration? A capture on my firewall interface shows the DHCP server is trying to reply - it is like the helper-address is not forwarding the dhcp reply (or is not getting it)
11:11:52.915180 IP (tos 0x0, ttl 254, id 17478, offset 0, flags [none], proto UDP (17), length 337)
10.217.5.1.67 > 10.4.16.222.67: BOOTP/DHCP, Request from xx, length 309, hops 1, xid 0xb53a220c, Flags [none]
Gateway-IP 10.217.5.1
Client-Ethernet-Address xx [|bootp]
11:11:52.918761 IP (tos 0x0, ttl 124, id 28096, offset 0, flags [none], proto UDP (17), length 344)
10.4.16.222.67 > 10.217.5.1.67: BOOTP/DHCP, Reply, length 316, xid 0xb53a220c, Flags [none]
Your-IP 10.217.5.12
Server-IP 10.4.16.222
Gateway-IP 10.217.5.1
Client-Ethernet-Address xx [|bootp]
Any ideas?Good morning -
I have a pair of 6513 in a VS40 (VSS quad sup) connected via L3 MEC to a VSS pair of 4500X. Active to Active and Standby to Standby connected in a L3 MEC port-channel that is also a vnet trunk:
(Core)
interface Port-channel5
description Distribution Uplink
no switchport
vnet trunk
ip dhcp snooping limit rate 100
ip address 172.20.68.1 255.255.255.252
ip ospf message-digest-key 1 md5 XXX
spanning-tree guard root
(4500 Distribution)
interface Port-channel1
description Core Uplink
vnet trunk
ip arp inspection trust
ip address 172.20.68.2 255.255.255.252
ip ospf message-digest-key 1 md5 XXX
The interfaces are all using LACP mode Active inside the channels
On the 4500 we have a global routing table and a vrf. Both have helper addresses pointing to the DHCP server which is extranet service behind the 6513 Core.
interface Vlan2301
description Global Routing Table
ip address 172.19.68.1 255.255.255.0
ip helper-address 10.4.16.222
interface Vlan2512
description VRF
vrf forwarding RED
ip address 10.217.5.1 255.255.255.0
ip helper-address 10.4.16.222
DHCP for the Global Routing Table subnet works. DHCP for the VRF does not.
What is interesting is if we shut down the link that is connected to the standby 4500 (Te2/1/1) DHCP starts to work for the VRF.
Using <debug ip dhcp server packet detail> at the 4500 here is what I am seeing.
When both links are up and DHCP is failing for the VRF:
Mar 10 20:02:02.419: DHCPD: BOOTREQUEST from 0100.1a6b.3a56.13 forwarded to 10.4.16.222.
Mar 10 20:02:10.473: DHCPD: Reload workspace interface Vlan2512 tableid 3.
Mar 10 20:02:10.473: DHCPD: tableid for 10.217.5.1 on Vlan2512 is 3
Mar 10 20:02:10.474: DHCPD: client's VPN is RED.
Mar 10 20:02:10.474: DHCPD: using received relay info.
When I shut the Te2/1/1 link down in the L3 MEC at the 4500 DHCP starts to work for the VRF RED:
Mar 10 20:04:41.354: DHCPD: BOOTREQUEST from 0100.1a6b.3a56.13 forwarded to 10.4.16.222.
Mar 10 20:04:41.369: DHCPD: Reload workspace interface Port-channel1.2002 tableid 3.
Mar 10 20:04:41.369: DHCPD: tableid for 172.20.68.2 on Port-channel1.2002 is 3
Mar 10 20:04:41.369: DHCPD: client's VPN is .
Mar 10 20:04:41.369: DHCPD: forwarding BOOTREPLY to client 001a.6b3a.5613.
Mar 10 20:04:41.369: DHCPD: no option 125
Mar 10 20:04:41.369: DHCPD: broadcasting BOOTREPLY to client 001a.6b3a.5613.
Mar 10 20:04:41.369: DHCPD: no option 125
Mar 10 20:04:44.808: DHCPD: Reload workspace interface Vlan2512 tableid 3.
Mar 10 20:04:44.808: DHCPD: tableid for 10.217.5.1 on Vlan2512 is 3
Mar 10 20:04:44.808: DHCPD: client's VPN is RED.
It is like there is a bug that is treating the L3 MEC as a L2 MEC when both links are present; or the VNET trunk is not being processed correctly.
Has anyone else used a L3 MEC with a VRF and a DHCP helper with success? Is this a bug?
03.05.01.E is the code we are running on the 4500X-32(SPF+)
This is also with TAC but I thought I would share with the community in case anyone else has a similar environment or if Cisco experts want to comment. -
Clients no received ip address from Non-root APs
I have 3 AP, one roor and Non-root. The Root AP is connected to ADSL modem which provide DHCP.
the clients form root AP received IP without problem, but whe I try to associate to non-root AP I can not receive ip from DHCP.
What it could be the reason???
I hope any of you can help me...
regards
ROOT#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater
Device ID Local Intrfce Holdtme Capability Platform Port ID
NON-ROOT1 Vi-Dot11 0 177 T I AIR-AP124 Vi-Dot11 0
NON-ROOT2 Vi-Dot11 1 145 T I AIR-AP124 Vi-Dot11 0
ROOT#
ROOT#
ROOT#sh dot11 associations
802.11 Client Stations on Dot11Radio0:
SSID [enlace] :
MAC Address IP address Device Name Parent Stat
e
0021.00d6.6459 169.254.32.107 Br-client - 003a.9924.2ba0 Asso
c
0025.9cab.3073 0.0.0.0 Br-client - 003a.9933.e070 Asso
c
003a.9924.2ba0 192.168.1.249 bridge NON-ROOT2 self Asso
c
003a.9933.e070 192.168.1.251 bridge NON-ROOT1 self Asso
c
58b0.3568.372c 169.254.68.25 Br-client - 003a.9924.2ba0 Asso
c
c417.fe02.645f 192.168.1.64 Br-client - 003a.9924.2ba0 Asso
c
d8a2.5e49.5a83 0.0.0.0 Br-client - 003a.9924.2ba0 Asso
c
ROOT#
ROOT#sh ver
Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.4(21a)JA1, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 19:06 by prod_rel_teamHi Surendra,
I set static IP on interface BVI1 on non-root1 and non-root2, also root-bridge I can ping to both of them, in fact I access to them via web and telnet.
I also set ip helper-address on interface Dot11Radio0 in all APs root and non-root..
My mind is about to crash...I don´t know what else to try.
thanks for your time.
Maybe you are looking for
-
Please fix this ASAP and anyone know of a fix.
-
CONSTANT Java Applet Problems, HELP!
Alright, since I've had my mac, Java has never worked properly. I have the latest version of OSX and of Java, I tried repairing permissions and also tried manually installing the latest OSX update, but whenever a website uses the Java Applet (for a g
-
Unable to run jsp as include using jsp:include tag
I am trying to run the basic jsp:include sample provided by Oracle in OC4J 10g. When I run the code, It seems like include file is treated as text/html and not run at all. Can somebody help me in figuring out what I am missing here.. Here is the code
-
* seems to be running ok now, sorry for the inconvenience Message was edited by: JopVerberne
-
HT5538 How do I enable my lap top to download I Tunes?
How do I enable my lap top to "download," I Tunes?