WRT150N v1.1 setup trouble

when the setup wizard detects the router, it says "Router Not Supported"....i'm using the disc that came in the box, and alreay checked to make sure it's for the right model
internet still works through it though

Can anyone help me with installing WRT54GS - my internet provider is Bellsouth (AT & T). Every time I go to connect the wireless router to my computer I can no longer get on the internet from my stand alone computer - we now have a laptop and we are trying to be able to assess the internet on the laptop and our stand alone computer. Help!!!

Similar Messages

WRT150N as access point troubles

Trying to use a 150n as an access point and am having troubles.
First my setup:
PC on XP, receiving wireless from my ISP through a wireless card in the PC.
Have no way to connect the incoming ISP signal directly to the 150N.
What I want to do, and have done it before with access points, is to recieve my ISP through my wireless card, send it to the 150N router via my network card, and then be able to access the 150N wireless signal throughout my home with a laptop.
I have done the searches and done the procedures to change the IP address of the router, however when I am done doing this I can no longer access the 150N through my network card. Have tried with a couple different computers and each time after the router is reconfigured it crashes the network card in the computer.
The only way to get back to the router is to press the reset button and start over.
I'm about to trash the router and go back to a standard access point of a different brand. I have never had this problem before. With today's technology there's no reason this shouldn't work with a standard router, yet all of them I see require a direct connection to a DSL or cable modem in order to work.
Help...........
Thanks

I'm trying to share the incoming connection wirelessly through the router/access point.
Incoming wireless to my desktop via wireless card, send that out through the network card to a router/access point, thereby creating my own internal wireless network which I can access with my laptops throughout the house.
The incoming wireless is a bit weak, so it does not allow a reliable connection to the laptops.
Basically the desktop will only function as a server system to the internal wireless network.
Done the same in the past, just gotta figure out how to do it with the new Linksys router.
Thanks
Tom

10g RAC setup trouble in Windows 2003 env.

Hello, guys,
I had trouble in setup 10g RAC in Windows 2003 env.
Environment is following.
* Two PC which have two LAN cards which one is connected public network, other is connected internal network.
And Two PC have SCSI card connected shared disk. Share disk is setup logical drive, not assigned drive letter.
* PC's OS is Windows2003 Enterprise Server. OS is installed clean, not contain previous oracle.
Due to install manual, At first setup CRS, second setup 10g. So I setup CRS at firast. During CRS setup, I input two PC's public name and private name in installing node window and proceed setup, setup program install program into two PC at the same time. But setup failed in last service configuration window, and CRS service can't start.
I checked error message in log file, error is about registry... I can't find cause.
Do you know how to setup CRS into two PC?

I could resolve this trouble.
Cause is that shared disk settig is affected. Another side PC can't mapped drive letter, so I assigned drive letter manually, and reboot both PC.
After that, OracleCRService, OracleCSService, OracleEVMService could run.
Thanks

UC 520 initial setup trouble

Hi -
I've got a UC 520 and am having trouble accessing the device to configure the initial setup.
I can connect using the console port, but I can't access the device thru CCA.
I do not get an IP address using DHCP when connected.
I can no ping the default port(s) 10.1.1.1 or 192.168.10.1 when using a static IP address on the same subnet.
I followed the steps on uc500.com to update the sfotware to 8.0.1 and to using the factory-default configuration.
I still can not access the device using CCA. The device also does not give out IP addresses to an IP phone when connected.
ANY tips/suggestions would be GREATLY appreciated.
Thanks in advance!

Press F2 while in CCA to view console logs while CCA does it's voodoo.
In my experience enabling telnet helps ALOT, because in the logs CCA is constantly trying to telnet, but can't if it's disabled and falls back to HTTP.
line vty 0 4
transport input all
Also make sure your interfaces are not shutdown. Assuming vlan 10 is your UC520 switch vlan:
conf t
int fa 0/1/0 - 8
no shut
int vlan 10
no shut

Exchange Activesync Setup Trouble

We are attempting to use the iPhone Configuration Utility to setup our new iPads and iPhones. I am running into problems getting Exchang Activesync to configure properly. I can manually setup each iPad to work correctly, but when attempting to use a profile (prompting users to enter their account information when the profile installs) the profile adds their email address incorrectly.
After entering all of the Exchange information and installing the profile on an iPad, the Exchange account incorrectly adds a "mail." to the server address. So for instance if our Exchange server is "mail.servername.xx" and email should be "[email protected]" the profile is being installed with their email address as:
"[email protected]" As a result the configuration of their account fails. I should add that our user names are not the same as our email account; is this confusing the utility/
How do I get the configuration profile to stop adding the "mail." to the email address?

For anyone having trouble setting up exchange email on your HTC Droid DNA i think my own started working now with this simple steps:
Email address: Your email
Server Address: mail.com
Domain: Blank
Username: Your complete email address
Password: Your password
Try it.

Basic home network setup troubles: Airport, ethernet, and cable modem

Hi,
Having only just subscribed to a cable broadband service we're experiencing some troubles setting up a mixed-mode home network and I'm wondering whether we've got some of the very basics messed-up.
What we have is:
1. Recent version (white) ibook, with airport, running 10.4.7;
2. Old G4 PowerPC (450MHz I think) running 10.4.7 ... airport card available;
3. Old powerbook (?Lombard) running 10.2.8 ... no airport;
4. A PC running Windows XP (not that important to have this in the network though) with no wireless;
5. A 3com SuperStack 1100 switch;
6. A cable modem;
7. A Linksys BEFSX41 Etherfast Cable/DSL Router ... 4 ethernet switch ports;
8. An airport express base station;
9. An HP laser printer connected into the ethernet LAN.
We'd like to keep both our wireless and ethernet networks running with all computers able to access one another, print to the laser printer, and access the broadband (fixed IP address) account. We're not (yet) conderned with hosting websites from our home computers.
I'm unsure of how we should configure this system. Do I connect the airport base station to the switch (which is what we presently have) or into the router? Do I connect each of the hardwired PCs (and the printer) into the switch
and then the switch to the router via single conenction?
If we use DHCP to access the router have I got the potential for the router and the airport base station to interfere with one another?
Any advice would be greatly appreciated. I've pulled a few TCP/IP setup-for-idiots books from our local library but this specific situation doesn't seem to be well covered.
Cheers
Dougal

You probably have a few options here that will work. Considering the number of wired devices, I would suggest the following:
Cable modem > (Ethernet cable) > [Internet port] BEFSX41 [LAN_1] > (Ethernet cable) > SuperStack switch > (Ethernet cable) > [Ethernet port] AirPort Express Base Station (AX) > (wireless) > wireless clients, AND
SuperStack switch > (Ethernet cable) > wired clients
Then setup the AX as a bridge, as follows:
To set up the AirPort Express Base Station (AX) as a bridge, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, make these settings:
Network tab
- Distribute IP addresses (unchecked)
- Apply the new setting.
- Wait at least 5 minutes.

Blackberry Bold 9900 email setup trouble

When i access the setup app and then select email accounts i receive instructions to "activate your enterprise account and enter details provided by your system administrator". From looking at information on the internet it seems i should be getting another option: "Internet Mail Account" but that option doesn't appear. I have just recently bought this phone and i have never set up an enterprise account. Now i can't access my emails through my phone. Any ideas?
Solved!
Go to Solution.

Before getting too deep in that, please call your carrier and confirm that you have the blackberry internet service added to your account. Without this service you will not be able to setup personal email on that phone. Not sure what add on they mention, but you have to have BIS added to your account in order to setup email. Even while on a wifi connection.
Please click the Thumbs Up icon if this comment has helped you!
If your issue is resolved, please click the solution button on the resolution!
Every BlackBerry should have BlackBerry Protect, get it now! | Follow me on Twitter | Bring Back BBM Music!

Xserve setup trouble

I'm trying to set up an Xserve at a high school in my town. Someone from a local college came to help, but he had never set up an Xserve before and we got stuck. We have already gone through the set up process (creating the account, attaching it to the internet and downloading the updates). Now we need to create accounts for all the students. I'm not exactly sure how to do this. The guy from the college tried doing it via the user options in system preferences, but it didn't work and didn't seem right. We then opened up the workgroup manager (thinking that it would allow us to do it). We weren't able to edit anything - then I noticed the lock symbol in the corner. However when we tried to unlock it, the admin password didn't work. What password should we be using? Are we even using the right application to set up networked accounts? I tried looking at the documentation, but it just confused me. We were left at a bad place - I'm not sure what part of the documentation we are at. Any advice?
Thanks!

I set up a Xserve, with workgroup access, last year. When I went to create user accounts, I discovered that I had to set the Open Directory usage to Open Directory Master, even though Apple's documentation made it sound as if this was unnecessary. Once you have your Xserve set to be an Open Directory Master, you will need to configure WorkGroup Manager in order to set up access for your users.
There are at least three essential Mac OS X Server Guides that you will want to have handy. They are
File Services Admin Guide
Open Directory Admin
User Management
I would actually recommend downloading all the server guides you can find on http://www.apple.com/server/documentation/. Try doing a search for any you don't find on that page. I also used the Getting Started booklet that came with the Xserve to help me activate Open Directory, but be aware that it only gives very basic help.
I had to read through several of the guides in order to figure out what to do. I would walk you through the steps, but it would take wa-a-a-y too long and you may not want the same setup I am using.
A couple of tips that are not obvious from the documentation:
1. You server must be connected to the network in order to set it up as an Open Directory Master.
2. WorkGroup Manager opens with the default Admin directory. You will need to switch directories in order to set up a workgroup for user access. To switch directories, click on the small globe icon just below the tool bar. You should be given some choices in a drop-down menu. You probably want the local directory, which should be /LDAPv3/127.0.0.1.
Once you are in the correct directory, you should be able to unlock it using your administrator password.
Xserves ship with a default admin password, but if you have changed that, the change should apply to WorkGroup Manager as well. That having been said, I had my Xserve hiccup and lose my admin password. When I reset it, I could not get WorkGroup Manager to recognize any password at all. I ended up having to completely reinstall OS X Server and then had to set the whole thing back up again. Fortunately, I had documented my setup as I went along - something I strongly recommend you do
I hope this helps. The real key is to read, read, read. Good luck.
-Phoenix

[SOLVED] Audio setup troubles with usb headphones and built-in sound

Hello,
I Just started using Arch about a month ago after going through many Debian and Ubuntu variants. After all my frustrations with apt pinning to get working 10bit video playback, only to have everything else uninstalled by crappy dependency checking, I am extremely happy with how easy it was in Arch.
Now I am having difficulties perfecting my audio setup. Almost everything else is set up to satisfactory levels but I have yet to bring the sound to the same standard. With just ALSA my built in audio works, but defaults to the unused hdmi on my nvidia graphics. I have managed to get it to switch at some point but with ALSA alone I could never get my usb headset to work at all.
By using pulseaudio as well I was able to get simutaneous playback, which is ideal, but had choppiness and other issues with just the usb headset. I followed some instructions found on the arch wiki and other places on the net for choppiness in both ALSA and pulse and tried the fixes listed in various combinations. I ended up with outcomes such as pulse not starting, no sound at all, creepy ticking in usb and perfect sound on speakers, and my current situation of perfect sound on speaker and acceptable but tinny sound on usb which degrades over time requiring restart.
Is anyone able to give any advice or point me to any guides I may have overlooked?
Setting up sound from scratch is something I have never done before coming to Arch, so I don't know what commands are useful for audio specifically, but learning is one of the reasons I decided on Arch. As for commands I do know, lspci and lsusb, relevant entries are as follows:
spricc ~ $ lspci | grep Audio
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
01:00.1 Audio device: NVIDIA Corporation GF104 High Definition Audio Controller (rev a1)
Bus 004 Device 003: ID 1532:000e Razer USA, Ltd
USB device is a Razer Megalodon headset, NVIDIA Audio is of no interest to me, unless it is not what i think it is.
Thanks to anyone who takes the time to read this.
Last edited by spricc (2012-03-23 15:21:11)

I managed to find a solution.
https://wiki.archlinux.org/index.php/Pu … oppy_sound
Following this exactly didnt work before, but setting the sample rate to 192000 instead seems to have done the trick

WRT150N problem with setup

i cant use the three option on the EasyLink Advisor cause i cant complete the setup. i follow to step by step that it told me to but on the step where it was trying to detect my router it said that router is not support. i try to download the lastest version of EasyLink Advisor but it still do the same things. ne one want to do plz tell me.

well...if the auto config tool is not working ... try setting up the router manually .. below are the steps you can try :
1)connect the computer to the router's port#1 and the modem to the router's internet port
2)access the router using http://192.168.1.1 . the default password is admin
3)on the router web ui, click on the "mac add clone" subtab .. enable it and click clone...save the settings and do a power cycle
4)go to the "status" tab on the ui and check the "internet ip add"
5)if it has a valid ip add , try going online
if facing any problem , let me know the ISP details whether cable or DSL ...

Not ready to give up yet....Initial setup troubles:

Hello. I am attempting to add Time Machine to an existing wireless network. I have followed the directions for doing so, which included resetting Time Capsule's name to a short one (this has been reported to have been an issue in other posts), changing my password, pointing TC to my wireless network, and finally, the TC is supposed to restart. Upon TC restart, Airport Utility is unable to "'see" my TC anymore. I rescan, rescan, rescan, to no avail. (Mind you, my Airport is connected, so there is network connectivity.) I then tried unplugging TC, and plugging it back in. Still not visable. I then reset TC to default settings, and started over again. The same exact process, and the same exact results. No exaggeration, probably 15 attempts over two days.
I really like the concept of this device, and feel like if I can just discover the rosetta stone I need to get it going, I'll be really happy. I have also invested so much time in this already, I really don't want it to be in vain.
So, my friends, can anybody tell me what I am doing wrong or could be doing better. For your information, my goal is to set TC up as an "additional wireless device" on my existing wireless network. I understand that my initial backup should be done by ethernet. I plan on doing that. But I can't do that until I get this initial setup squared away. Thanks.

Hi Richard, I have not done the manoeuvre of primary backup via ethernet (I wish that I had, it took 5 hours but I cannot see that this would make any difference to your problem (I could be wrong of course) - The fact is that there is currently a MASSIVE bug with the Time Capsule Disk in that it will not auto-mount on the desktop - that is, you can't see it!
The quick fix is to open a finder window (Command - N) and select your Airport router in the left hand panel (under 'Shared') and in the adjacent right hand column select 'Time Capsule Disk' - it will then magically appear on the desktop!
Until Apple fixes this issue in their next system update, I have found that this is a simple-enough-for-me workaround which auto-mounts the Time Capsule Disk at login:
Go to Automator > custom action > Files & Folders. Next add/drag 'Get Specified Servers' from the centre column to the right hand column, then you click the 'Add..' button and then select your Time Capsule Disk server (whatever you have named it) in the window which opens and add it to the 'Get Specified Servers' window. Next you add/drag the 'Connect to Servers' function from the centre column to the right hand column - and that's it! Test the Automator app by clicking 'Run' and that should make your Time Capsule Disk appear on the desktop (you can eject it first by dragging it to the trash if it's already there). Finally save the Automator workflow as an application, then put it into your utilities folder and having done that you can then add this new utility application to your Login Items in System Preferences > Accounts so that when you start your Mac the Time Capsule Disk auto-mounts.
I hope that this info is appropriate and that I have not entirely misunderstood your issue (which is entirely possible :)) Best, Donald..

Tomcat setup trouble.

Hello.
I downloaded a pre-configured version of tomcat and have set my class paths etc but I can't connect via a browser. The page loads to localhost but it is just white and blank.
This is what I get on after calling catalina run from a command prompt:
C:\>paths
C:\>set PATH="C:\Program Files\Java\jdk1.5.0_10\bin";C:\WINDOWS\system32;C:\WIND
OWS;C:\WINDOWS\System32\Wbem
C:\>set JAVA_HOME=C:\Program Files\Java\jdk1.5.0_10
C:\>set CLASSPATH=.;C:\apache-tomcat-5.5.17\common\lib\servlet-api.jar;C:\apache
-tomcat-5.5.17\common\lib\jsp-api.jar;C:\Servlets+JSP;..;..\..
C:\>cd C:\apache-tomcat-5.5.17\bin
C:\apache-tomcat-5.5.17\bin>catalina run
Using CATALINA_BASE: C:\apache-tomcat-5.5.17
Using CATALINA_HOME: C:\apache-tomcat-5.5.17
Using CATALINA_TMPDIR: C:\apache-tomcat-5.5.17\temp
Using JRE_HOME: C:\Program Files\Java\jdk1.5.0_10
01-Feb-2007 23:38:39 org.apache.catalina.core.AprLifecycleListener lifecycleEven
t
INFO: The Apache Tomcat Native library which allows optimal performance in produ
ction environments was not found on the java.library.path: C:\Program Files\Java
\jdk1.5.0_10\bin;.;C:\WINDOWS\system32;C:\WINDOWS;"C:\Program Files\Java\jdk1.5.
0_10\bin";C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem
01-Feb-2007 23:38:39 org.apache.coyote.http11.Http11BaseProtocol init
SEVERE: Error initializing endpoint
java.net.BindException: Address already in use: JVM_Bind:80
at org.apache.tomcat.util.net.PoolTcpEndpoint.initEndpoint(PoolTcpEndpoi
nt.java:297)
at org.apache.coyote.http11.Http11BaseProtocol.init(Http11BaseProtocol.j
ava:138)
at org.apache.catalina.connector.Connector.initialize(Connector.java:101
6)
at org.apache.catalina.core.StandardService.initialize(StandardService.j
ava:580)
at org.apache.catalina.core.StandardServer.initialize(StandardServer.jav
a:791)
at org.apache.catalina.startup.Catalina.load(Catalina.java:503)
at org.apache.catalina.startup.Catalina.load(Catalina.java:523)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:266)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:431)
01-Feb-2007 23:38:39 org.apache.catalina.startup.Catalina load
SEVERE: Catalina.start
LifecycleException: Protocol handler initialization failed: java.net.BindExcept
ion: Address already in use: JVM_Bind:80
at org.apache.catalina.connector.Connector.initialize(Connector.java:101
8)
at org.apache.catalina.core.StandardService.initialize(StandardService.j
ava:580)
at org.apache.catalina.core.StandardServer.initialize(StandardServer.jav
a:791)
at org.apache.catalina.startup.Catalina.load(Catalina.java:503)
at org.apache.catalina.startup.Catalina.load(Catalina.java:523)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:266)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:431)
01-Feb-2007 23:38:39 org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 937 ms
01-Feb-2007 23:38:39 org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
01-Feb-2007 23:38:39 org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.17
01-Feb-2007 23:38:39 org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
01-Feb-2007 23:38:41 org.apache.coyote.http11.Http11BaseProtocol start
SEVERE: Error starting endpoint
java.net.BindException: Address already in use: JVM_Bind:80
at org.apache.tomcat.util.net.PoolTcpEndpoint.initEndpoint(PoolTcpEndpoi
nt.java:297)
at org.apache.tomcat.util.net.PoolTcpEndpoint.startEndpoint(PoolTcpEndpo
int.java:312)
at org.apache.coyote.http11.Http11BaseProtocol.start(Http11BaseProtocol.
java:150)
at org.apache.coyote.http11.Http11Protocol.start(Http11Protocol.java:75)
at org.apache.catalina.connector.Connector.start(Connector.java:1089)
at org.apache.catalina.core.StandardService.start(StandardService.java:4
59)
at org.apache.catalina.core.StandardServer.start(StandardServer.java:709
at org.apache.catalina.startup.Catalina.start(Catalina.java:551)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:294)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:432)
01-Feb-2007 23:38:41 org.apache.catalina.startup.Catalina start
SEVERE: Catalina.start:
LifecycleException: service.getName(): "Catalina"; Protocol handler start fail
ed: java.net.BindException: Address already in use: JVM_Bind:80
at org.apache.catalina.connector.Connector.start(Connector.java:1096)
at org.apache.catalina.core.StandardService.start(StandardService.java:4
59)
at org.apache.catalina.core.StandardServer.start(StandardServer.java:709
at org.apache.catalina.startup.Catalina.start(Catalina.java:551)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:294)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:432)
01-Feb-2007 23:38:41 org.apache.catalina.startup.Catalina start
INFO: Server startup in 1672 ms
but it seems to hang and does not return to the prompt which I would imgaine is wrong.
I used a bat file to set my paths which is below:
set PATH="C:\Program Files\Java\jdk1.5.0_10\bin";%PATH%
set JAVA_HOME=C:\Program Files\Java\jdk1.5.0_10
set CLASSPATH=.;C:\apache-tomcat-5.5.17\common\lib\servlet-api.jar;C:\apache-tomcat-5.5.17\common\lib\jsp-api.jar;C:\Servlets+JSP;..;..\..
can anyone spot what I may be doing wrong? or give me advice on what I could try to change? as you can see there is an error although it still says it will stat at the bottom.
Thanks and regards
Mike

Hi, I changed the port back to default and it worked. I got to the Tomcat index page and viewed some JSP examples. All was going well...
Then I clicked to view an example and the page would not load firefox says waiting for local host. I shutdown Tomcat and re-started it and it let me view an example, then the same thing happened. I can not get it to work properly, after it starts it works fine for 30 seconds and then won't load the examples.
Any ideas what could be the problem?
BTW I dont have IIS installed on this machine.
Thanks
Mike

Invoice setup trouble - Help appreciated!!!!

Hey there.
I've been making some stationary for my company and need to finish this invoice in Pages. I have 5 columns (Date, Description, Daily Rate, Days Worked and Total) and a final cell as a total due on the last row. I've obviously managed to do the sume to multiply the daily rate with days worked to make the total and then the total due underneith, but this is only one row.
I want to set it up so that I can add a row underneith and the calculations all work and add up to the total due. At the moment when you add a new row, it just adds a blank one with no calculation info. Is it possible to make this work?
Would also be nice if you could dynamically put the date in, but thats not much of a problem.
Thanks for any help!!!
Christian

Someone else may have a better idea for this, but here goes mine.
As far as I can tell, you can't add a dynamic date within table cells. (I assume you are using a table for your form.) The simple solution is to add the date (Insert->Date&Time) outside of the table proper -- say the upper left or right corner of the document just above the table proper.
While you can't add rows and have calculations work, you can delete them. For example, if I have a formula that says =SUM(B2:B7), and I delete rows 6 & 7, the formula still works. What you might have to do is start with more rows than you need and then delete the unused ones as you work with each form.
Jim

Skim-setup-trouble

Hi there from overseas!
In the near future i'd like to input CJK (and hopefully soon some Russian and Mongolian words as well) but got stuck with my first configs of scim/skim (on KDE). Well, I've been trying to follow the skim-help-dialogs within kde (German locale). Anyway it seems to be quite outdated, because the menus shown there wouldn't match the skim ones. eg in the helping instructions there is an entry "SCIM servers" which probably could be those "IM Engines" I read about, but I couldn't find both in my skim-config~ Additionally, while clicking on 'Input Methods'|'Generic Tables' there is always an error 'couldn't find kcm_skimplugin_scim_tables.la' showing up; I don't know what that could mean, I already installed scim-tables~
Please help!
thx, nexus
Edit: I so far installed the following pkg's:
scim
scim-pinyin
scim-tables
scim-hangul
scim-chewing
scim-anthy
scim-m17n
skim
Last edited by nexus7 (2007-06-09 18:11:44)

Well, found something similar in the meanwhile, look here.
So, according to this my error could be s.th. bad with the scim-tables...
Aditionally, her'es my ~/.xinitrc-entry (following this thread):
export XMODIFIERS="@im=SCIM"
export GTK_IM_MODULE=xim
export QT_IM_MODULE=xim
scim -f socket -c socket -d
And all these plugins seem to show up usually in here in a doublepack of files ending {.la,.so}:
/opt/kde/lib/kde3/kcm_skimplugin_scim_tables.so
while my .la is missing instead. Any ideas?
Last edited by nexus7 (2007-06-09 20:36:49)

Computer wont run setup

hi i bought a hp pavillion all in one pc. they lady i purchased it off had restored it to factory settings. i bought it home plugged it in and turned it on. it gets to setup is starting then a window pops up saying the computer was restarted abruptly or an unexpected error occurred please restart computer to restart setup. trouble is thats all it keeps doing please can someone help me please.
This question was solved.
View Solution.

I am glad to hear it is all sorted out.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

WRT150N v1.1 setup trouble

Similar Messages

Maybe you are looking for