WRT400n and PS3 wireless issue

I have recently purchased a WRT400n and want to hook up my PS3. I would not consider myself technologically inclines, but can figure things out, and I am at a loss. Both computers in house (wireless laptops) work great. The PS3 on the previous router, worked great. When i set up the PS3, i am getting slow connection speeds, and cannot get full gaming experience if I am online for an extended period of time. Cant hear me, lags, etc.... occur and I get an error on the PS3 of "Failed connection speed test". Any thoughts as to how I can fix this situation would be great!! Thanks for your help.

Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
On the set-up tab change the MTU Size to 1365 and click Save Settings...Click on "Administration" tab and disable the option UPnP and click Save Settings...Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...
**Also disable UPnP and Change MTU on the router.

Similar Messages

Can you help resolve a "Go Wireless" and Verizon Wireless issue?

How do you file a complaint against "Go Wireless" and Verizon wireless? It was partially my mistake because I didn't realize that Go Wireless charges a premium for their service. That said, I was informed by the sales person that I could get the $150 bill credit per phone line I ported over, and a $200 visa card for each smart phone I turned in. That's $350 for each phone in credits.. This seemed like a great deal, so I purchased 3 phones, samsung galaxy 5. I paid a $50 premium per phone to buy them from the store (note..there are NO PRICES listed, you have to rely on what the sales persons quotes you). I also paid a $20 per phone "set up" fee and a $10 sim card fee. Again, I take responsibility for not asking if other verizon stores charged these additional fees. HOWEVER, when I was told to go to the corporate verizon store to get the envelopes for to turn in the smart phones for the $200 per phone credit - this was not my lack of research. I did go to the corporate office and was told that the $200 offer had ended 7 days ago. I went back to "Go Wireless" and the store manager told me that the employee was misinformed and was working off a quote sheet that was out dated. Ok, now you'd think they'd offer something to fix their "mis-informed" employees mistake. No, they said there was nothing they could do. I could return each phone for an additional stocking fee of $35, and cancel my plan. So, here I am...paid a premium for the phones, was "misinformed" by a store agent who was working off an outdated specials sheet, and my only recourse is to pay $105 to return the 3 phones. Something isn't right here. Verizon won't do anything, Go Wireless won't do anything. Any suggestions?

My girlfriend had a similar issue because her new device was not updated to IOS7 when she turned it on, but her backup point was created using IOS7. Check to be sure the restore point was created and then factory reset the phone after you have updated to 7.

Borderlands and ps3 controller issues

hi i play borderlands on my imac, i use my ps3 controller as a gamepad and i have one issues. When playing the game when trying to bring up such things as vendor screen to buy items it will not stay. I played it without the controller and it works fine, so it something to do with the controller being used. Is anyone else who plays like this have this problem? How can i fix it

My wife and I have the same problem with our respective iMacs when we play Borderlands. There is obviously a bug somewhere either on Feral's end or Apple's Bluetooth end. There is one solution that I discovered, if you don't mind keeping your controller tethered to your computer via USB.
Step 1: Make sure your PS3 controller is not currently paired with your Mac (I am not certain if this step is critical or not, but this how I do it to get it to work).
Step 2: Startup Borderlands and begin your game.
Step 3: Plug your PS3 controller into your Mac via USB (your charaters perspective will begin to spin around on your screen).
Step 4: Press the clear circular button in the middle of your PS3 controller and keep your controller plugged into your Mac. Do not unplug your controller from the USB port until you are done playing your game (you should now be able to use your controller in the game without that annoying glitch).

Nokai E71 and PS3 Wireless Headset pairing problem

hi!
My PS headset should be good with my E71 Phone,
but i have no idea, how to pair them!
I've tried to find answer online, but couldn't.
Could someone please give me some advice?
Thx!

many have talked about its need, I dont know when a software update will enable this
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

WRT54G Wireless G Router and PS3

Hi there, I am a proud owner of the above mentioned items. The reason why I am posting this is that when I am playing on the PlayStation 3 and one of my other family members are on a hardwired computer, the hardwired computer I believe looses it's connection to the internet, but my PlayStation is still connected to the internet, and it works very good. My setup for my network is I have a laptop, Nintendo Wii, and PS3 connected wirelessly, and I also have two hardwired computers. I asked around on the internet, and other people said that I should not be having issues, and if I were that it might be something wrong with the firmware of my router. I do have the router fully updated with the latest firmware, so don't recommend that to me. So my question is, is anybody else having a similar issue, or am I just all alone on this, and is this a firmware issue, and if so, is Linksys doing anything to fix this issue? In case if anybody was interested, I have the version 6.0 of the WRT54G router.

Make sure your firmware is up to date. If not, upgrade it, reset and reconfigure the router.
The box said windows xp or better... So I installed Linux!

WRT310N v1 and MacBook Pro wireless issues

Hi all,
I've been having ongoing wireless issues with my WRT310N v1. I have a macbook pro (early 2009) with mac os 10.5.8. I have cable internet, with a DHCP connection. I have a computer and PS3 hardwired through the router, and they work flawlessly. The wireless, however, has never been what it should be. Internet loads slow, even though the connection speed is pretty good (not as fast as hardwired devices, but close).
Here are the wireless settings:
wireless config: manual
network mode: mixed (the Macbook can get wireless-n, by iPhone is only g)
Radio band: standard 20 mhZ
wide channel: 9 (can't change this with this config, unless i go wide channel at 40 mhZ)
standard channel: 11
SSID broadcast: enabled
I've got WPA2 security, with AES encryption. I've set the Beacon interval to 75, and left the Fragmentation and RTS thresholds at default. The firewall is activated, and "filter anonymous internet requests" is disabled.I'm wondering if I'm losing so much speed by broadcasting a mixed signal, instead of just G or just N. I've tried transmitting only in Wireless-N, but there's no noticeable change (and the iPhone can't connect at all).
Any input at all would be really appreciated. I'm hoping I don't have to fork over $30 to linksys just to get tech support. Thanks in advance.
Solved!
Go to Solution.

Well its not necessary to power cycle your router everytime whenever you make any changes on your Router. But if you re-configure all the settings on your from scratch, then its better to power cycle your router.

WRT400N and 4965agn issue.

I have a Gateway M6864FX laptop that came with an intel 4965 agn wireless adapter. I've looked up the specs and such and found that it can be run on 2.4 or 5 ghz spectrums. I recently upgraded my router to a Linksys WRT400N with the simultaneous dual band. At the same time I also purchased a linksys dual band usb adapter for my fiance's laptop that has an older intel pro g adapter. I've set up both 2.4 and 5 ghz correctly. I planned to use the 2.4 spectrum for us to use our Iphones with and the 5 ghz for our laptops. I set hers up first and had no issue with finding and connecting to the 5ghz network. My laptop, on the other hand, only finds the 2.4 ghz network. I've gone about updating the driver for my card from the intel site and still don't find the 5ghz.
Am I missing something here? Even distances don't make sense. She uses hers on the other side of our house without issue and my laptop is maybe 2 feet from the router.

I think it might be the problem with the Intel adapter itself. You may try some settings on your Computer, i think this will make your adapter recognise 5Ghz network.
Under your advanced port settings of your adapter you should be able to force it to n only.
Also turn off IP6 protocol on your computer this helps some times since there are really no networks requiring it.

Issues connecting psp and ps3 airport extreme

Im having issues connecting my psp and ps3 to my airport extreme.

I have the newest airport extreme (square) & I was able to connect my psp, ps3 and Nintendo DS to it wirelessly once I change the security back to WEP. It seems that they were having trouble connecting to my WPA protected network.
Also, go into airport utility and manual settings. Under the Wireless tab, make sure that the radio mode option is set to the first options (8.02.11n (802.11b/g compatible) and not the other options.
Hope this helps.

Is anyone else having email problems such as apps exiting in the middle of an email? It may be a wireless issue. I use First Class for work and yahoo email for personal. I will be in the middle of typing a long email and the app just quits, all data lost.

Is anyone else having email problems such as apps exiting in the middle of an email? It may be a wireless issue. I use First Class for work and yahoo email for personal. I will be in the middle of typing a long email and the app just quits, all data lost.

Have you tried restarting or resetting your iPad?
Restart: Press On/Off button until the Slide to Power Off slider appears, select Slide to Power Off and, after the iPad shuts down, then press the On/Off button until the Apple logo appears.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds). Ignore the "Slide to power off"

I have had wireless issues sense Leapord, any fixes yet? its a shame that my wife has to sit in front of our 27 inch imac on a $300 Windows computer to use the web effectively. I have tried all fixes and some work while others don't but all temporary

This Lion wireless issue has become more than just an irritation, so much so, my wife has resorted to sitting in front of a 27 inch imac with a 300 dollar Walmart Windows computer to get the bills paid and use the web. And yes, there is not a fix out there I haven't tried over the last year or so, some worked and some didn't, but all were temporary at best. Same issue with my Macair, I wonder if its a hardware issue, like the video card in my 2006 MBP, it went out after the warrenty and then I found out there was a calss action suit going on over it, unfortunately Apple wouldn't cover it and wanted 7oo bucks to fix it, sold that as parts.
While i really like me Macs, I own three, I may have to bow out and stick with LINUX, that has yet to let me down, anyone know if Mountain will fix this issue? or are we all just waiting for defective WiFi cards to fail at our own expense, PS, got three Macs for sale.

Sounds like you're getting kernel panics, which are usually, but not always, caused by hardware problems, with memory being one of the regular culprits.
First thing I would do is to get our your original OS X disks, insert the first one (should say 'AHT version x.x' in small print on the label - if not, find the one that does), and reboot holding the Alt key down. Choose the Apple hardware test, and when prompted, choose the extended test. If you have either of the TechTool programs, they can do similar testing. Does that identify any hardware issues?
Next, I'd download rember from http://www.kelleycomputing.net/rember/ . This is a memory testing program that you can set to run overnight. Does it come up with any errors? If so, try resetting your memory card(s) by removing and putting back into the computer. Rerun memory test.
This FAQ will provide other details: http://www.thexlab.com/faqs/kernelpanics.html

T420 - Intel Wireless and Windows XP issue?

Has anyone else seen any issues with using the Intel Wireless Advanced-N 6205 card on Windows XP? I have a 4178-6UU and it will work for a while, then just stop receiving packets, but will not disconnect even though it doesn't work and I am no longer able to ping it.
I have the latest driver available from Intel and Lenovo (14.0.1.2), and also the latest BIOS (1.22). Unfortunately, I have to have XP/SP3 on these T420's. Any suggestions or is anyone else seeing any issues?

Have you solved this issue? If so how? I think I may have the same issue. I don't understand all terminology in the post such as "ping", so I can't be certain if it is exactly the same issue. Also I use Windows 7 Pro. However in certain locations but not all, my wireless capabilities are horrible. The same locations that worked just fine with my Dell E6400, that I recently switched from are not working on my lenovo T420 4178-6UU. The internet access is constantly loss and I have to reconnect over and over again throughout the work day. HELP!!!! (SN: This keyboard is the best I have ever worked on, I don't think I will ever buy a different kind of PC, that is if I can resolve this wireless issue).

Sierra Wireless EM7345 ThinkPad 8 and 10 general issues

This was posted as a reply to german forum but it was deleted Symptoms (mobile connection is connected)
1. mobile connection randomly disconnects. It is possible to reconnect again. 2. when resume from Connected standby mode the mobile connection appears to be connected but it is dead. It is not possible to disconnect nor turn off the mobile connection, it is stuck. Windows restart is required to resolve it. 3. when resume from Connected standby mode the EM7345 composite device disappears at all from Device Manager and new unknown device '1 CDC' appears. Windows restart is required to resolve it. Note: Issues 2 and 3 occurs when running on battery only. I don't have any occurence when the tablet was plugged in AC, turned off (into Connected standby mode) and on, yet. I have already tried to reinstall the 1.6.10513.4153 driver, no luck. I have also tried to disable 'USB selective suspend' feature in driver settings and switch off GNSS device (because it has Sierra Wireless driver), no change. I have latest BIOS 1.24 (ThinkPad 8, 64 bit). It is hard to reproduce the case 3 but I have almost reliable steps: 1. uninstall current driver (even it is the latest version)2. restart3. install current 1.6.10513.4153 driver, select Custom Setup, make sure the 'WWAN Logging Tool' is selected, finish the installation4. restart 5. establish mobile connection6. go to Start menu, Intel group, start 'M.2 WWAN Logging Tool'7. press Start Trace button8. turn off the tablet (while the tracing is running) by power button, wait for a minute 9. turn on the tablet(repeat steps 8 and 9 multiple times, in case you can not reproduce it at the first time) EM7345 device disappears with typical unknown 1 CDC device. Yes, it is not a standard operation but it is easily reproducible with the same result. Similar issue is reported in other forum posts for ThinkPad 8 and 10
http://forums.lenovo.com/t5/ThinkPad-Tablets/Thinkpad-8-with-Sierra-Wireless-EM7345-Driver-or-Firmware-issue/m-p/1758961http://forums.lenovo.com/t5/ThinkPad-Slate-Tablets/Tablet-8-win-8-1-unbekanntes-Gerät-1-CDC-kein-mobiles-breitband/m-p/1839400http://forums.lenovo.com/t5/ThinkPad-Tablets/Thinkpad-10-EM7345-stops-working/td-p/1742115http://forums.lenovo.com/t5/ThinkPad-Tablets/Flaky-WWAN-in-ThinkPad-10/m-p/1793007 Additional related issue - firmware update does not work
Old firmware 1.1 that can not be updated to 1.2, read this thread http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T540p-Sierra-WWAN-EM7345-reliability/m-p/1839271#M106663 The 1.2 firmware might help to resolve the issue (although this post states it actually did not help). Technical details When the USB composite device (EM7345 = WWAN + GNSS) disappears it incorrectly identifies itself as VID = 1519, PID = F000 so Windows can not find proper driver for the device and displays it with (?) icon. If you remove the '1 CDC' device from Device Manager and perform 'Scan for hardware changes' this time it is correctly identified as VID = 1199, PID = A001 and installed (these tasks can be automated using devcon.exe command-line tool, so the fix wouldn't require OS restart everytime it occurs. It is still hack, not a solution). It looks like a firmware bug because the USB composite device and WWAN MBIM device uses Microsoft generic driver. Summary Given the price tag of ThinkPad 8 and 10 tablets, Lenovo should fix that because this is basic functionality failure. Disappearing WWAN device that needs full restart is really serious issue. And again, please diagnose and resolve the issue (hint , hint) instead of "try to reinstall this, try to reinstall that, replace this, replace that" advices. It leads to nowhere because the driver/firmware is buggy as it was in the past with Ericsson device. (copy of the post is stored)

More details. I installed USB Device Viewer from Windows Driver Kit to get some information. When the EM7435 device is healthy: [Port3] : USB Composite Device
Is Port User Connectable: no
Is Port Debug Capable: no
Companion Port Number: 0
Companion Hub Symbolic Link Name:
Protocols Supported:
USB 1.1: yes
USB 2.0: yes
USB 3.0: no
Device Power State: PowerDeviceD2
---===>Device Information<===---
String Descriptor for index 2 not available while device is in low power state.
ConnectionStatus:
Current Config Value: 0x01 -> Device Bus Speed: High (is not SuperSpeed or higher capable)
Device Address: 0x05
Open Pipes: 6
===>Device Descriptor<===
bLength: 0x12
bDescriptorType: 0x01
bcdUSB: 0x0200
bDeviceClass: 0xEF -> This is a Multi-interface Function Code Device
bDeviceSubClass: 0x02 -> This is the Common Class Sub Class
bDeviceProtocol: 0x01 -> This is the Interface Association Descriptor protocol
bMaxPacketSize0: 0x40 = (64) Bytes
idVendor: 0x1199 = Sierra Wireless Inc.
idProduct: 0xA001
bcdDevice: 0x1729When the EM7435 device disappears and is shown as unknown '1 CDC' device [Port3]
Is Port User Connectable: no
Is Port Debug Capable: no
Companion Port Number: 0
Companion Hub Symbolic Link Name:
Protocols Supported:
USB 1.1: yes
USB 2.0: yes
USB 3.0: no
---===>Device Information<===---
String Descriptor for index 2 not available while device is in low power state.
ConnectionStatus:
Current Config Value: 0x00 -> Device Bus Speed: High (is not SuperSpeed or higher capable)
Device Address: 0x02
Open Pipes: 0
*!*ERROR: No open pipes!
===>Device Descriptor<===
bLength: 0x12
bDescriptorType: 0x01
bcdUSB: 0x0200
bDeviceClass: 0x02 -> This is a Communication Device
bDeviceSubClass: 0x00
bDeviceProtocol: 0x00
bMaxPacketSize0: 0x40 = (64) Bytes
idVendor: 0x1519 = Comneon GmbH Co., Ohg.
idProduct: 0xF000
bcdDevice: 0x1234 I have also tried to diagnose what exactly happens after returning from Connected standby usingUSB hardware verifier but as usually I can not reproduce it while the tool is used

WRT320N. Port forwarding help. Xbox and ps3 playing at same time. NAT issues

Hi
I'm trying to have both my xbox and ps3 play with open NAT's for online gaming. I have had success utilizing info from 'portforward.com'. But the solutions will unlock OPEN NAT for either the ps3 or the xbox .. one at a time. Is there a way to get both to be open?
It seems like one main conflict is the success depends on both utilizing port 3074. But I can't have both use it? ( obviously).
I tried port forwarding the xbox per specs off of this forum and that works great.. And DMZ ing the PS3. But like i said before. Most solutions
leave one console with OPEN and one with Moderate.
Is there a solution that allows both NAT OPEN's on both consoles?

First of all XBOX works on a different port number and PS3 works on a different port numbers. Follow the steps below to open the ports on your router for XBOX and PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
This settings are for your XBOX.
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
For PS3 Follow the steps below
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

Airport Express (Model with 802.11G +54MBPS Mac/PC and Set Up Issues

Hi,
We have a 4 Mac and 1 PC Household. Cable Internet Service by Roadrunner.Cable model (owned) connected to a D-Link 802.11G wi fi router (by ethernet from cable modem)in the family room , then out to a Imac (the half moon base and LCD screen with a airport card also in the family room and the closet computer to the D-Link
router, (we did add a D-Link antenna to the router ? about 10 months ago (a D-Link ANT24-0700 (Version 1.2)and a HP 4 in 1 printer attached via USB to the Imac
,a eMac 1.25 ghz 1Gb ram with airpot card also connected wirelessly (no printer attached on the same floor but in a ajoinging room about 20 feet from the Router, and another eMac 1.0 Ghz 1Gb ram with airport card in the upstairs part of our house (a bedroom) and no issue with Internet connection (it has a Epson 3in 1 printer attached via USB, and a MacBook Pro with 802.11N wireless card in side , bought for a Christmas/Birthday Present and also for college.It to has no issues with the Internet where ever it may be in the house. Our sole PC a HP tower with a added D-Link WDA -2320 Range Booster Desktop Adapter (802.11G) and we added a D-Link Antenna same model as the other a ANT24-0700 to help with Internet access which it did as well as adding some ram to increase page loading time etc. It does not have a printer attached. I will get to the Topic Area now
The Airport Express. I was not involved in the set-up as I was laid up due to a bad back and post major knee surgery , But I always (especially recently) wondered why the light was amber and blinking. I read through the manual and also
Apple.com support and MacFixit.com (which is under construction and moved to part of Cnet.com)and then went to the Airport Express Discussion area (sorry for being so wordy) I need a Twitter account to post!) We have a network name for the D-Link and the computers all were added and it also supports a Xbox 360, a Sony PlayStation 3 and a Nintendo Wi (in online use without issue) but..
A network was also as it appears to myself) for the Airport Express and under the half moon bars showing connection strenght (there is our D-Link network "phoenix" with security protection WPA2 I believe) as I have set up the router, We had a Apple Base station prior that was ? 802.11B (a half moon white unit) still have it in the box ) So for normal daily use, checking e-mail and internet use all of the computers use the "phoenix" or D-Link supported Router 802.11G
and The other network calld Apple Network with numbers and letters after it (and hopefully security) password is unknown , The Airport Express is set up connected via USB to a HP B&W laser printer which has saved quite a bit of money on ink, To utilize that printer you must switch from "phoenix" The D-Link router network to the Apple Network (followed by letters and numbers) The Imac and the eMac in the family room and a ajoing room (after switching to the Apple Network
can than print to the lasr printer. The eMac upstairs and the HP Windows XP Professional software can not print to the laser printer (yet the HP PC shows it as a individual network and a strong signal, equal to the Internet connection from the D-Link, and the eMac (after switching under the half moon (not the proper name I am sure) to get to the Apple Network to print , it will not print, yet it shows a 5 bar signal, same as the D-Link connection. I do believe we have two seperate networks (but do not understand why the two Mac's in the family room can print to the laser printer by simply switching networks and then file and print. ** One other 9probaly major item is that it states to set up the Airport Express with a Mac With OSX 10.4 or later (at the time of set up, we had the Imac and two eMac's all running Panther OSX 10.3.9 9which they continue to have installed) We obtained the HP Tower and Monitor and HP 4in 1 printer ust before Christmas in 2008 and the MacBook Pro in Mid December 2009 (current model and running Snow Leopard 10.6. The HP Tower runs Windows Xp Professional (Service Pack 3) so the MacBook Pro which is much more mobile , could be used to do the set-up, or the HP Tower coulf be moved temprarily, I do recall if Router changes (at least with The D-Link You need to be connected by Ethernet to the Mac
that would be doing the set up/configuration of the router (and it runs OSX 10.3.9 and is a older Mac (with 80Gb Hard drive that is partioned for OS9 and OSX as well , it is under a Ghz processor wise and less than 1 Gb of ram as the last ram slot required a seal to be broken and 256mb of ram (?) could be added
it has 768 mb of ram but knock on wood running well. We use Lacie external drives
on the Imac and both eMac's and need to get external drives for the HP PC as well as the Mac Book Pro (15" screen)
I apoogize if I repeated myself, and rambled but I wanted to (in one post) to explain our set up and network configuration
Questions
1) if indeed it is that the two networks is true and a set yp that is not correct
can the Airport Express be configured without opening up the router (when ever that happens it seems one computer is unable to get online and each time its a differnt one a Mac or veen the PC
The PC under My Computer and Networks clearly shows the wto distinct and seperate netwoks with strong signals and the distance is not far (it is through a floor as the other emac and the PC are upstairs and cabling by ethernet is not a option
2) If I need to open the router would I add the Airport Express as a client as if it was one of the computers or gaming systems on the network? (adding the Mac adress or IP address (not sure how you find the Mac address) and its been while since the router was opened up for any additions or work on it.
3) would it be on the same channel as the router or not ?
4) Hopefully with proper configuration the light will stay on (and green) on the A/E and the eMac and HP PC will be able to print to the laser printer. Currentlt
when anything needs printed from the PC its put on a Flasg Drive and plugged in tothe Imac and the the Apple Network is selected and data printed, The eMac upstairs has the option of using the attached Epson 3 in one or doing the Flash stick work around.
I would be verya appreciative if some one took a look at the set up above and advised me of what is right, what is not right* and what to do to fix things up
I would imagine after proper set up, delete the Apple Network from the PC and eMac upstairs and ? all of the computers as we should have one base station (the D-link and the spoke (the A/E connected by UBS to the A/E (it may be ethernet but the cable connection from the A/E to the HP laser printer is correct (the rest of the A/E set up ... Please , tell me where it is and where it should be
and ? any idea why we can print to the laser printer down stairs and not up stairs ? it did mention printer set up with Panther as possible, page 43 of themanual we have un chaper 5 Tips and Troubleshooting (under whn your printer isn't responding) (we do not have the interfereance listed in the manual,
our phones are land line, one 900 mghz and the others 5.8 ghz
It is possible to move the A/E and laser printer if that would help the two computers (desktops) upstairs) bt the distance is way less than 150 but their is a floor and ? duct work (metal ) but I think here is a place to stop typing and let some of the experts on the discussion forums take a look.
one lst note (as the lap top will be going off to college in the fall (runnning Snow Leopard, and the other 3 Mac's run Panther OSX 10.3.9 should the HP PC windows Xp Professional be the computer to set up the air port express and the Airport Utility proram installed & would this conflict with the current Router (set up by a Macc running OSX 10.3.9 (Panther) i.e (should both set ups be on the same computer?) but actually aThe D-Link is OSX10.3.9 compatible (and 802.11G) and set up requires ethernet connection to a Mac (You type in the numbers and . etc and password as administror and you are in, or should the admin be on the same cpmpuer for the router and A/E ?
(and considering a Airport Extreme Base Station as well as dual frequency simulataneus and 802.11N (for the laptop now) and future, or wait. The 802.11
in theory would broadcast farther..?? even if computers had 802.11b(our Mac Desk tops and the PC 802.11B card
Thanks Again!!!
Many, Many Thanks
amnienttales

William Boyd Jr.
Hello again,
D-Link Router is model DGL-4300 (along with a D-Link ANT24-0700 Omnidirectional
7dbi Antenna . Our Cable Internet ISP (Roadrunner) provides consumers with dynamic ISP address's . All Mac's have Airport Cards and The Hp Tower XW4550 has a D-Link Rangebooster G Desktop Adapter WDA-2320 (also with a D-Link ANT24-0700 Omnidirectional 7 dbi Antenna (the PC OS is Win XP Pro Service Pack 3) The 3 desktop Mac's run OSX Panther 10.3.9 , The 15" MacBook Pro OS is OSX 10.6 Snow
Leopard (not sure what is after the .6 (right now) D-Link's website is
http://www.dlink.com , I have configured this router multiple times in the past.
also added as clients on the network (Utilizing the D-Link Router) are a X-Box 360, Sony Play Station PS3, and a Nintendo Wii all of which have on line ability
and enables online video game play with any one online.
As mentioned prior the Airport Port Express is Model A1084 Part No. M9447OLL/A
which is USB conected to a HP LaseJet B&W , model 1020 and some how the two computers near it can switch to the Airport Express Network from the D-Link Router based Network and print wirelessly to the A/E connected LaserJetPrinter
I realize I will need to reconfigure the D-Link Router and add the A/E as a client. I will try first to use the Airport Utility and see if I can do anything
Utilizing it (adding it to the D-Link network, I think its unlikely but worth a try but* the password is unknown but I have a few guess's as to what it may be.
I do have the necessary admin and network paswwords to cconfigure the D-Link Router,
1) * If the the A/E Utility experiment fails and I need to re-configure the router * do I need to (as per the Airport Express Set Up Guide (Use a Mac with OSX 10.4 or later or a PC with Win Xp Home or Professional (have a desk top PC that has the specs) and The Mac Book Pro meets the Mac Spec's)
If I can not get a password to work on the A/E I would reset it using the reset button
And before plugging in the A/E , connect the appropraite cables in our case a USB cable to the LaserJet Printer then plug in the A/E
2) I would then connect by Ethernet from Either the Mac Laptop or The PC to the D-Link router (if not the router will not set-up correctly)
3) The one question that puzzles me is that we are not using the A/E as a base
but a client
in two sections(Using Airport Express , connecting a Printer via USB
and use Airprt Utility to create a new network or join a new newWireless computers using Mac OSX 10.2.7 (Tiger) or later or a PC with Windows XP and it then goes in to the steps of ising the printer for both a Mac and a PC (using Bonjour on the CD that came with the A/E (this appears to contradict needing to use Mac OSx 10.4 or a PC with Win Xp set the A/E up for use as a printer
(joiing a new network or existig one)
And in Chapter 5 Tips and Roubleshooting= Your Airport Express Status Light Flashes amber & Your Printer is not responding (it is flashing amber and the printer does not respond to the two computers upsstairs (one Mac running OSX 10.3.9 & One PC running WinXp and its states to make sure the printer is selected
in the Printer list o client computers, to do this on a Mac using OSX 10.3 or later , open Printer Set Up Utility and follow steps and if a PC with Windows XP , Open Printers and faxes and then follow steps
in Closing ? can I configure the A/E Utility with a Mac using 10.3.9 as above or
? Per Chapter 1 Getting Started use a Mac with OSX 10.4 or later or a PC with Windows Xp Home or Professional
Perhaps I am taking the tips and trouble shooting and Printer Set up out of context or does the getting Started Computer specs contradict them or are they
for use if the A/E was going to be a Base Station and not a client..
Will keep at it,
ambienttales

How to get nat type 1 with airport extreme and ps3?

I use airport extreme as my default router. I have my ps3 connected to a separate airport in a different room. I can only get nat type 2 and want to get nat type 1 as I can barely connect to any hosts online.

NAT type 1 is when you connect your PS3 directly to your modem with no router in between. The problem with this is that there will be no way to share your internet connections with other devices. NAT type 2 is where you have a router in between your modem and your PS3, and NAT type 3 is where you have some or all needed ports blocked which is where you would have issues.
NAT type 2 is a correct way for your PS3 to work, and your wireless connection strength may be the reason for connection issues.

WRT400n and PS3 wireless issue

Similar Messages

Maybe you are looking for