WRT54G.connection help needed

so here is the problem,do not have great computer knowledge so i will try to explain in my terms. im presently online using my router although it does not connect automaticaly when turn my computer on.well it says that the internet is now connected although it does not work , so i have to do my usual dial-up connection and it works fine. so how can i get the connection to work straight away without ressourcing to my dial-up connection?
thank you

You would need a broadband connection such as a Cable or DSL from your ISP. Then you would need a router either wired or wireless if you plan on using a wireless laptop or other device. With the router configured for what ever type of internet connection you would be able to turn you PC on and already be on-line. The router will control your internet connection and allow you to network multiple computers to share one internet connection, printers and other files on the other PC's.
Richard Aichner (Ikester)

Similar Messages

WRT54G v6 Help needed!

Okay, I have a wrt54g v6 router that I use for 2 computers and an xbox (xbox live). Im getting an intermittent signal on all my devices and I have no clue as to why. All of my devices are connected via ethernet cable so I know its not wireless interference and i've changed everything I can think of that would cause this problem, firmware, MTU size, etc. I even created a static ip for my xbox. But the router is still getting degraded signals, the only thing I havent really done is uncheck all the boxes on my router firewall but to me that wouldn't do anything but allow more access to my already crappy network. If anyone has a solution or knows whats going on that would be so so helpful, thank you very much.

You might need to upgrade the firmware of the router as is normal for most WRT54G v6 routers.
Verify the router firmware version
1) click on start ---> run (type in cmd)
2) on the DOS Prompt (type in ipconfig)
► take note of the default gateway value
3) open up Internet Explorer and type in the default gateway value
4) username: leave it blank password: admin
5) go to the status tab: verify the firmware version
► if it's below 1.00.9 (i.e 1.00.0, 1.00.1, 1.00.4, 1.00.6, 1.00.7) then the router definitely needs an upgrade.
To upgrade the firmware:
1) download the firmware from www.linksys.com/downloads Look for your product model number from the list (i.e WRT54G v5)
2) save the file on your desktop
3) access the 192.168.1.1 page again
4) go to Administration - firmware upgrade
5) browse for the downloaded file and upgrade.
► Press the reset button of the router for 30 seconds and powercycle (i.e turn on and turn off the router).
► Reconfigure the router as per ISP settings.

WRT54G install HELP needed

I bought the WRT54G so I could go wireless in the house. I run the CD and it goes "do you want to replace your existing router or keep it?" Near as I know I DON'T HAVE ONE but that isn't an option, so which do I pick? There should be a "do you simply have a modem plugged into your PC and bought this go to wireless?" type option (something I'm betting is extremely common). Also, once you select one, you cannot go back and change your mind...you have to exit the program and start over. Which of these cryptic options do I choose??
(Mod note: Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 06-15-2009 07:12 AM

Disregard - got help from an online tech spt.
FWIW that install CD needs work, as it was detecting a router that doesn't exist and the tech spt explained that sometimes it is known not to work properly.
PS: in the interests of hopefully saving someone else the time and hassle I went thru, here are the steps I was given which worked fine:
1. Connect the PC to the port one of the router then restart it. (This PC should be the one that can get online if directly connected to the modem).
2. Go to your desktop and double click on Internet Explorer or any browser(Located on the Start Menu in Windows XP).
3. When the browser opens, type http://192.168.1.1 on the Address bar and click on Go or press the Enter key. The log-in window will appear.
4. Skip User Name and type admin on the Password field, and click OK.
5. Configure the wireless settings. Click on the Wireless tab and have these:
Wireless Configuration: Manual
Wireless Network Mode: Mixed
Wireless Network Name (SSID): Bill/Anything that you would want to name your network.
Wireless Channel: 1
Wireless SSID Broadcast: Enable
Save the settings.
6. To secure your wireless network, Please click on the Wireless security sub-tab that is still under the Wireless tab and change the Security mode to WEP and have these:
Default Transmit Key: 1
WEP Encryption: 64 bits 10 hex digits
Skip the Passphrase field. Do not click on the "Generate" button.
Enter any 10-digit value in the Key 1 box. (You may use all numbers but you can only use letters A to F. No dashes or slashes and special characters). This will be your WEP key (MINE: ssn123123)
Leave Key boxes 2-4 blank or empty.
Save the settings.
7. Click on the Setup tab, then click on the MAC Address Clone sub tab, enable it and click on "Clone your PC's MAC" then save the settings.
8. On the Setup Tab --> Basic Setup sub-tab, look for the LAN IP which is 192.168.1.1.
9. Change the IP address to 10.10.10.1 then save the settings.
10. Connect the modem to the router's Internet port and wired PCs to the router's numbered ports.
11. Power cycle. To do a power cycle, please power off the computer, the router and then the modem. After 2 minutes, power on the modem, the router and then, lastly, the computers. Wait for the lights to stabilize before plugging the next device.
Message Edited by Bill12344 on 06-16-2009 08:34 AM

Time Capsule Connection Help Needed (Flashing Amber)

Guys,
I've been trying to troubleshoot my Time Capsule connection for a week now and I have had zero luck.
I have a Imac with OSX 10.6.8 that uses AirPort v 5.6.1. I have a Cat-5 (ethernet cable) plugged from my Time Capsule port (looks like this <-->) into an available port in my cable mode/router. My Imac is also plugged into this router. The two cat-5 (ethernet) cables are side by side.
So....
Every time I plug in the Time Capsule I get the following prompt via AirPort.
AirPort Utility found a Time Capsule 802.11n (4th Generation) that is
reporting problems.
Time Capsule's Name : My Capsule
          IP Address: 10.0.1.1
          Versino: 7.6.1
          AirPort ID: 12:88:93:CC:FF:72
If this is not the AirPort wireless devise you want to setup you can select another from the list on the left. If you don't see it make sure.... Blah blah blah....
To make a long story tollerable I do see my Time Capsule on the left at the top. Its the only one and its selected by default. So I do the next logical thing right? I click "Continue" and AirPort reads the Time Capsule's configuration.... and then...... I get the error
An error occurred while reading the configuration.
Make sure your Apple Wi-Fi base station is plugged
in and in range of your computer or connected via
Ethernet and try again. (-6753)
Can anyone help me understand why I can grab the Time Capsule's IP Address but AirPort can not read the hardware's (Time Capsule) config?
I'm at a loss.
Could my ethernet cable be the issue?

Hackintosh,
Thanks man... Yes, I plugged it into the circle symbol with no joy. I also went to Wal Mart and baught a new seven foot cat-5 for $10. Again I still have the flashing amber light.
After plugging in the ethernet cable into the circle icon port AirPort returns the following prompt.
I reset the TC (ball point pen to the reset hole untill fast blinking amber light occurs) and entered the needed params and it returns this error.
An error occured close the configuation window and try again.
It must be a config parameter that I'm setting incorrectly. There's a bunch so who knows what I'm doing wrong.
I just need the to talk to my Imac so i can get a backup executed. A wireless connection will take too long.
FYI: The cat-5 is brand new and is 100% functional (green light on the TC and router.)

Airport Express/Router Connection - Help Needed!

I was given an Airport Express for Christmas to use to beam my iTunes from my iMac to a pair of powered speakers in a different room. I was using the AE in conjunction with a Netgear wireless router.
It was a pig to set up but now I wish to change everything and I might need help.
I want to connect my router to the iMac by ethernet cable - the 2 bits of equipment are only 2 feet apart! Thus the AE will be the only piece of kit connected wirelessly to the router.
I would like to delete the present connection of AE to router and start again.
Is there anything I need to know about changing my router to Mac connection from wireless to wired and reinstalling my wireless connection from router to AE?

Is there anything I need to know about changing my router to Mac connection from wireless to wired and reinstalling my wireless connection from router to AE?
For the iMac:
System Preferences > Network > Show > Network Port Configurations
o Verify that a Built-in Ethernet option exists. If it does not, click "+" to create one. (Note: If you are unable to create a Built-in Ethernet configuration, the Ethernet card in your computer either doesn't exist or it is not recognized.)
o Verify that Built-in Ethernet is at the top of the list. If it isn't, you can drag it to the top.
Advanced > TCP/IP tab
o Configure IPv4: Using DHCP
o Configure IPv6: Automatically or Off
Advanced > DNS tab
o Verify that your ISP's DNS server(s) appear. If they do not, click "+" add them.
Advanced > Proxies tab
o Configure Proxies: Manually
o Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
o Exclude simple hostnames (unchecked)
o Bypass proxy settings for these Hosts & Domains: <leave blank>
o Use Passive FTP Mode (PASV) (checked)
Ethernet tab
o Configure: Automatically
For the AX:
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
*AirPort > Base Station*
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
*AirPort > Wireless*
o Wireless Mode: Join a wireless network
o Network Name: <existing Netgear's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
*_In iTunes:_*
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

CONNECTION HELP NEEDED

Whenever I try to log into ichat it says I can't because the connection has timed out. I believe it could be because I am at school and something I need to do something with the network to make ichat run. I know the school doesn't block ichat so that's not it. I really don't know what to do, PLEASE help me. It works fine at my house but not here!

Hi
Try logging on to AIM on port 443 rather than port 5190.
Go to IChat in the menu bar > Preferences > Accounts.
Log out of AIM and then use the Server Settings tab
Set the port to 443.
Log back in again.
Tony

Chicken of the VNC connection help needed

Hello! I am not sure this is the right forum to post but it didn't seem to fit anywhere else. I have Airport Extreme v. 5.6 and am trying to connect to Chicken of the VNC. No luck. I selected the ARD settings in my system preferences, opened the firewall (which I don't like to do, wish there was a more secure way to control a client computer) and set up my connection on port 5900 in the airport admin utility. I have noticed that the IP my widget gives me is different than the one the base station reads. Help is appreciated Thanks

Hi Taryn,
Thanks for your quick and helpful reply. It is a bit
advanced for me at this point to comprehend, so if
you could simplify a bit for the remote connection
newbie that would be great, thanks so much :o)
That was the relatively simplistic explanation!
In order to remotely connect, the VNC client (you) needs to know the IP address of the VNC server (the remote computer you wish to connect to).
Every computer connected to the internet has an IP address, such as 200.100.54.14.
Some people have a fixed IP address, most though will be assigned an IP address by their ISP and this will generally change as and when they connect at different times.
However some people like to connect their networks to the internet which means that the network needs to share the single IP address connected to the internet.
This is usually done by a router, the router connects to the internet and this router has the external IP address. The router then using NAT to share the single IP address with multiple computers on the internal network (a subnet or LAN (local area network)).
What this means is that a computer on the LAN will have an internal IP address, this maybe fixed.
So when you send a remote connection request to the remote network, the router needs to know which computer on the LAN you are trying to connect to. You need to map the traffic coming in to the router to the specific machines you are trying to connect to.
This means that the remote router needs to be configured before you can remotely connect to a computer on the remote LAN.
I did just find out that I have been attempting to
connect with a laptop that has an every changing IP
(according to the client),
You (well he) could use a service such as Dynamic DNS to solve this issue.
http://www.dyndns.com/services/dns/dyndns/
but he is going to see
about transferring his work to his home computer that
has a fixed IP address. Does that sound more doable?
Depends on whether he has a router (see above)
Finally, do you think the pay services like ARD or
Timbuktu are perhaps safer? We like COTVNC because it
is free but I am very worried about the
confidentiality of my data.
COTVNC is according to the documentation secure.
Have a look at this guide as well.
http://guides.macrumors.com/RemotelyControlling_anotherMac

Oracle to Access: Generic Connectivity, Help Needed

Please come to this forum and help me
Generic connectivity for M.S ACCESS?
Thanks

MS drivers for Oracle was designed a very long time ago with Oracle7 in mind.
You might want to see: http://support.microsoft.com/kb/244661
I have not tested your code, but I guess you need to consider giving up on the idea of using ancient interfaces such as Jet. Not sure about MS' supporting the technology, but at least the older "win 95" versions seem unlikely to be Unicode-enabled.
Edited by: orafad on Mar 20, 2012 10:57 PM
Edited by: orafad on Mar 20, 2012 10:58 PM

Creative Cloud Connection Help Needs Mac Support

I'm very happy to see that the Creative Cloud Connection preview is now available.
I was VERY disappointed to see that the Help file only covers Windows computers. Please update it to support Macintoshes as well!

The "Creative Cloud Help / Getting started with the Creative Cloud Connection" page does have a section on MacOS: http://helpx.adobe.com/creative-cloud/kb/desktop-sync-getting-started.html
Is there a specific problem you're having with Creative Cloud Connection that you need help with?

Desktop Manager connection help needed

I have a new macbook running Snow Leopard and a Blackberry 9700 Bold running the RIM 5.0 software.
When I first got this Mac, I downloaded and installed desktop manager, and had no problems syncing my address book and calendar with the mac address book and calendar.
A few days ago I was attempting to clear the cache on Google Maps on my Bold, and it triggered JVM 102. I was unable to reload the apps from the mac, so I used my old PC and did a successful application loader. (formally worked in bb support doing this all day long, so i'm fairly certain this didnt cause the issue).
After this point, I can still sync with the PC with no problems, but the Mac will not connect to the device.
What happens is:
- Desktop manager begins "connecting to device"
- device asks if i want to turn on mass storage (selecting yes or no makes no difference)
- mac gains access to blackberry media card for a moment
- device gets solid red light, and reboots
- desktop manager says "waiting for device to restart"
- when device finishes booting, desktop manager says it was unable to connect
- mac gives errors about not ejecting properly
- bold reboots again
I have tried uninstalling and reinstalling the desktop manager
I tried using pocketmac but i refuse to pay them 4.99 for the "free download" accellerator
I tried missing sync but the trial/beta is invalid and they want me to buy the full program
I went into library/preferences and deleted all blackberry/rim related files, as well as searched entire mac for any blackberry/rim/research in motion files and deleted them, restarted the mac, and reinstalled DM, still having same issue
Connected back to PC again, still able to sync with no problems
Please help or let me know if there is any other information needed to try and help!!

Hi hnigrone and welcome to BlackBerry Support Community Forums,
When you reloaded the handheld software, did you perform a clean application load on the BlackBerry smartphone? You can find the steps for a clean application load outlined in the following BlackBerry Knowledge Base article:
http://www.blackberry.com/btsc/KB11320
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Database connectivity help needed

Hello all,
I am trying to connect the oracle database and facing the following error.
Enter user-name: sys as sysdba
Enter password:
Connected to an idle instance.
SQL> startup
ORA-16032: parameter LOG_ARCHIVE_DEST_1 destination string cannot be translated
ORA-07286: sksagdi: cannot obtain device information.
HPUX-ia64 Error: 2: No such file or directory
SQL>
Any help would be appreciate.
Regards

Hi,
Check the value of LOG_ARCHIVE_DEST_1 in your parameter file.
Is it pointing to correct location?
Do post the value of this parameter if you find any difficulty.
Regards
Anurag

Oracel connection help needed

Hi all,
I had Oracle 8i at my server side.
I had Oracle 10g as client in my system.
Can i connect the database exist in oracle 8i?
please help.

I had Oracle 8i at my server side.
I had Oracle 10g as client in my system.
Can i connect the database exist in oracle 8i?
See Metalink DOC ID 207303.1. I think they are not certified versions but previously oracle 10g client was supported for oracle 8i(only 8.1.7 version).
Regards.

WRT54G connection help!

just got it and i have verizon dsl
ran the cd and plugged everything in like it told me
came to the password and entered my own
then it searches for the connection and there is an error
it basically says that my desktop computer cannot connect to the internet
i know i probably need to manually configure something but what?

Hi…..
While running the setup disc when it prompts for the password type admin and then try to continue the setup for the router.
Or else you can also try the Linksys automatic tool in order to get the router configured www.linksysfix.com/check

Front Panel Audio connection help needed

I own an MSI 790GX-G65 with Realtek HD audio, installed in an NZXT Tempest case.
Using the AC-97 plug from the case into the MB JAUD1 connection I get front panel headphone audio, but no mic input or automatic detection from the Realtek manager.
In short: Which plug(s) do I use on the MB socket JAUD1? I will detail my NZXT front panel connections.
NZXT Connectors:
Maxi Plugs:
HD Audio
AC-97
Mini-Plugs:
MIC-IN
Ground
L-Out
Ret-L
Ret-R
R-Out
MIC-VCC
FYI: I'm using Windows 7 64 bit. OS has been updated to current.
Thanks for your help.
Merry Christmas!
Robert

Ok. I checked and confirmed... I DID use HD Audio in JAUD1. I only thought I was using AC97... The problem still is:
Front Panel Headphones: Okay.
Front Panel Mic: Not detected at all.
Audio driver version is 6.0.1.6316
Audio Controller HD Audio
Audio Codec: ALC889
DX11
Window 7
Thanks for any further suggestions

WDTV Live connection help needed

Hi,
I just changed ISPs yesterday to BT Total Broadband, i've managed to get everything to connect ok, but I can't stream content over to my WDTV Live, it finds it on the
Home Network > Devices ok but when I go to find files over on my WDTV Live under Network shares, it finds nothing
it worked fine on my old ISP
any ideas?

also in case you dont know about it there is a whole section all about this on the wdtv forums here;
http://wdtvhd.com/index.php?showtopic=8944

WRT54G.connection help needed

Similar Messages

Maybe you are looking for