WS6608 blade - port not registering to Call Manager

I'm having issues with my WS-6608 blade communicating with my Call manager. I have a total of 8 ports on this blade which
4 are currently active. The configuration is basically the same as the other active ports. Port 7/6 is not registering to my call manager. please help

the potr does not look like to be connected. Make sure 7/6 connected to the PSTN and there is actual connection?

Similar Messages

Host not registering with the Management Center

Hello,
We have CSA MC v5.2. I have put a pre-defined CSA on a server (seperate from the CSA MC), which installed successfully and the MC sees the host.
However, although a pre-defined CSA is successfully installed on a host (non-server), I am unable to get the MC to see it. On the host, the CSA simply states that it's, "Not registered with the Management Center."
Please help in resolving this.
Also, is there a Windows Vista fix? Currently, I am unable to get the CSA to install on Vista.
~ Mike

If you look at the CSA log file, it will tell you an error code for why the connection is failing. Use the list below to determine what your error code means...
OKENA_STATUS_INVALID_SYSTEM_CONFIGURATION = 2000,
OKENA_STATUS_ICC_FAILED_GET_HANDLE = 2001,
OKENA_STATUS_ICC_FAILED_TO_WRITE = 2002,
OKENA_STATUS_ICC_FAILED_TO_READ = 2003,
OKENA_STATUS_ICC_INVALID_TOPOLOGY = 2004,
OKENA_STATUS_ICC_INVALID_INITIATOR_COMP = 2005,
OKENA_STATUS_ICC_INVALID_PAYLOAD_SIZE = 2006,
OKENA_STATUS_ICC_INVALID_VERSION = 2007,
OKENA_STATUS_ICC_INVALID_COMP_ID = 2008,
OKENA_STATUS_ICC_INVALID_PAYLOAD = 2009,
OKENA_STATUS_GROUP_DOES_NOT_EXIST = 2010,
OKENA_STATUS_INVALID_REGISTRATION_PARAMS = 2011,
OKENA_STATUS_HOST_HAS_REGISTERED_BEFORE = 2012,
OKENA_STATUS_INVALID_CONTACT_INFO = 2013,
OKENA_STATUS_HOST_NOT_REGISTERED = 2014,
OKENA_STATUS_MISSING_CONTACT_INFO_PARAMS = 2015,
OKENA_STATUS_INVALID_REGISTRATION_ID = 2016,
OKENA_STATUS_ICC_INVALID_BYTE_ORDER = 2017,
OKENA_STATUS_ICC_NOT_INITIALIZED = 2018,
OKENA_STATUS_COMP_CONFIGURED = 2019,
OKENA_STATUS_UNDEFINED_MGMT_SERVER = 2020,
OKENA_STATUS_HTTP_TRANSACTION_FAILED = 2021,
OKENA_STATUS_ICC_INVALID_HANDLE = 2022,
OKENA_STATUS_SERVER_IS_REACHABLE = 2023,
OKENA_STATUS_HTTP_TIMEOUT = 2024,
OKENA_STATUS_ICC_NO_CONNECT_MUTEX = 2025,
OKENA_STATUS_FORCE_POLLING_NOW = 2026,
OKENA_STATUS_REGISTRATION_REJECTED = 2027,
OKENA_STATUS_LOAD_CONFIG = 2028,
OKENA_STATUS_DB_ERROR = 2029,
OKENA_STATUS_LICENSE_REACHED_LIMIT = 2030,
OKENA_STATUS_REGISTRATION_NOT_ALLOWED = 2031,
OKENA_STATUS_NOT_ALLOWED_TO_STOP_AGENT = 2032,
OKENA_STATUS_CLIENT_UI_NOT_ALLOWED = 2033,
OKENA_STATUS_FAILED_TO_PRINT_AGENT_REPLY = 2034,
OKENA_STATUS_INVALID_LICENSE = 2035,
OKENA_STATUS_TIMED_OUT = 2036,
OKENA_STATUS_REGISTRATION_BACKOFF = 2037,
OKENA_STATUS_TESTMODE_ON = 2038,
OKENA_STATUS_TESTMODE_OFF = 2039,
OKENA_STATUS_INVALID_SERVER_FQDNS = 2040,
OKENA_STATUS_INVALID_SERVER_IPADDR = 2041,
OKENA_STATUS_SERVER_DNS_NOT_RESOLVABLE = 2042,
OKENA_STATUS_SERVER_IPADDR_NOT_OWN = 2043,
OKENA_STATUS_SERVER_DNS_NOT_OWN = 2044,
OKENA_STATUS_SERVER_NAME_NOT_FQDNS = 2045,
OKENA_STATUS_FAILED_OPEN_PROCESS = 2046,
** please rate if this helps**

Which Ports do MCU and Call Manager use for Video?

Hi, Does anyone know which ports the MCU and call Manager Use when using the 3511 MCU box with Call Manager 4.1.3. I am looking to open the appropriate ports on the firewall.
Regards
Dominic

Dominic,
If your MCU ports are Callmanger controlled, they will use Skinny (SCCP) to communicate on TCP port 2000. Please see the following link.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00801a62b9.shtml
Hope this helps. If so, please rate the post.
Brandon

UCCE 7.5.1 - CTI Route Point and CTI Ports not registering in UCM 7.1

We are in a middle of a new installation of UCCE 7.5.1. The customer will use it only for Outbound calls. The design is to have on PROGGER and one AW, with a cluster of two CallManagers. All the setup has finished regarding the UCCE. Also, the CallManagers have been configured, regarding the CTI Route Point and the CTI Ports. All of these are associated with the PG USER which is CTI Enabled. Configuration on UCCE has been done, including the DIALER, except for the agents and the campaigns.
The problem is that the CTI Route Point and the CTI Ports on CallManager are not registering. Is this normal, since the agents and the campaigns have not been configured yet or there is an error somewhere?

Looks fine.
Is the Dialer running? Maybe those 30VIP phones the Dialer uses as ports to dial from won't be registered until the Dialer starts.
But they should also be registered if you start dialogictest over the full set.
What's the "route point". Who asks for it? Is it a dialed number that runs a script?
Regards,
Geoff

What is call manager doing with Jabber guest if you have no endpoints registered to Call manager?

Our Call Manager deployment is in it's VERY early stages. We have a Telepresence infrastructure at the moment (VCS Control and Expressway). All of our TP endpoints and Jabber Telepresence clients are registered to the VCS. What is going on that the Jabber guest and VCS server need call manager for? I know it's REQUIRED in the manual and I saw a slide somewhere that said using Jabber Guest without Call manager is NOT SUPPORTED.
Realistically though, I might not get permission to build a SIP trunk between the new Call manager and VCS for some time..so...supported or not will it work without call manager or is there something going on that's critical on call manager to make it work regardless of the fact that there is nothing registered to CUCM?
thanks!

Hi Douglas,
As you've gathered this configuration is not supported, and hence we don't actively test it or document it. That said, it should work fine
Mike

What will happen if Conference Bridge (CFB) is not registered with Call Manger?

I have a MRG consists of two CFB, it is found one is registered with CCM, the other is not. some users complain that the ad-hoc conference soft button is not working. So is that due one of the CFB is not registered? (I know all same type of resource within a MRG will be round-robin balanced).
will happen Call Manager allocate an unregistered CFB?

It will not allocate the unregistered one. Media Resource Manager will look for the available resources registered with CUCM according to the configuration and allocate the one thats available.
-Terry
Please rate all helpful posts

Sap to non sap connection ( program not registered/cpic-call

Hi all,
 Im trying to connect sap to siebel system.IN TCP/IP connections iv selected register program id & passed the parameters ...program id,gateway host and gateway service
i followed michal krawczyk steps & also checked in smgw
transaction also but program id is not registered there
 im getting error like program sapprog not registerd cpic/call
Detailed error
 Error - program sapprog is not registsred
 location - sap gateway on host saple / sapgw01
 detail - Tp sapprog is not register
 component - gateway
 counter - 387
 module -gwr3cpic
 line- 1621
 return code - 679
 subrc - 0
 please try to help me out in this issue. all inputs r rewarded.
Regards,
Lavanya

Hi
Thanks prince,iv checked entries in sm59, i checked smgw tranaction(gateway monitor) for logged on clients
its showing like this
number/luname/tpname/sys.type/hostname/hostaddres/last req
0 /sapnav/sapgw00/local_r3/sapnav.sapdomain.com/192.158.3.219
if i double click on above...
read/write socket = 4
handle = 4
time = tue jan 26 16:54:13 2006
socket = 1652
stat = ni_connected
type = stream ipv4
out = 1122 messages 64 bytes
in = 1 messages 64 bytes
local =127.0.0.1:3300
remote = 127.0.0.1:1848
options =
lu = sapnav
tp = sapgw00
lon lu = sapnav
long tp = sapgw00
ext program = 0
no conversation = 24
appc version = 6
hostaddr[0] =
hostaddr[1] = 127.0.0.1
offset in = 0
timeouts in = 0
connected = tue jan 24
last req = mon jan
request block number in= -1
connection out = -1
target out = -1
offset out = 0
restlen out = 0
timeouts out = 0
request block number out = -1
accept info = einfo
snc forced = 0
just see gateway monitor 4 sapnav/parameters & attributesProfile
parameter Value
gw/max_sleep 20
gw/conn_disconnect 900
gw/conn_pending 60
gw/gw_disconnect 1800
gw/req_stack_size 30
gw/max_conn 500
gw/max_wp 0
gw/max_conn_per_wp 10
gw/cpic_timeout 20
gw/deallocate_timeout 600
gw/reg_timeout 60
gw/reg_lb_level 1
gw/reg_lb_default 20
gw/side_info C:\usr\sap\D01\DVMGS00\data\sideinfo.DAT
gw/sec_info C:\usr\sap\D01\DVMGS00\data\secinfo.DAT
gw/startup C:\usr\sap\D01\DVMGS00\data\gwstartup.DAT
gw/stat 0
gw/tcp_security 1
gw/cpic_security 1
gw/max_sys 300
gw/max_shm_req 50
gw/max_shm_req_per_conn 10
gw/max_overflow_size 5000000
gw/max_overflow_usage 10
gw/keepalive 300
gw/reg_keepalive 300
gw/compatibility 0
gw/monitor 1
gw/netstat_once 1
gw/close_routes 120
gw/timeout 0
gw/internal_timeout 0
gw/nitrace 0
gw/accept_remote_trace_level 1
gw/resolve_timeout 0
rdisp/max_gateways 100
rdisp/max_comm_entries 500
rdisp/sna_gateway sapnav
rdisp/sna_gw_service sapgw00
rdisp/TRACE_LOGGING OFF
gw/rem_start REMOTE_SHELL
gw/remsh rsh
exe/gwrd C:\usr\sap\D01\SYS\exe\run\gwrd.EXE
snc/enable 0
snc/permit_insecure_start 0
Attributes
Release 640
Release no 6400
internal version 2
start time Tue Jan 24 16:53:47 2006
build time Aug 17 2004 23:33:51
build with Unicode TRUE
build with Threads TRUE
gateway hostname sapnav
gateway service sapgw00
req_sync_limit 24
appc_ca_blk_size 34396
gwreq_ln 34588
appcdata_ln 34316
overflow_size_limit 500000
overflow_use 0
trace level 1
trace level external programs 2
PID Gateway Reader 4952
internal version 2
Shared memory Sizes in bytes
CONN_TBL entry 1748
CONN_TBL total 874000
STATISTIC area 1392
iv changed some values for my safety.plz check it and let me know the error to register program id. Hope ull solve my issue this time.
Thanks in advance,
Lavanya.

CTI route point and CTI ports not registering - UCCX 10.5 and CUCM 10.5 - PARTIAL SERVICE

I'm trying to integrate CUCM 10.5 and UCCX 10.5.
For some reason CTI route point and CTI ports are not registering on the CUCM and the status of the UCCX is "PARTIAL SERVICE".
On the UCCX Cisco Unified CCX Engine is in status "PARTIAL SERVICE" and the Unified CM Telephony Subsystem shows status "OUT OF SERVICE".
I tried with completely new installation of UCCX twice and got the same result twice.
But when I tried integrating UCCX 10 with the same CUCM 10.5 from above everything works fine and all the ports are registering right away.
In all the cases I have done the same configuration.
The versions of CUCM is 10.5.2.10000-5.
The version of UCCX is 10.5.1.10000-24.
The version of UCCX 10 with which it works fine is 10.0.1.11001-37.
Does anyone have an idea what might be the problem?

No I haven't. Unfortunately I don't have a 32bit Excel at the moment to try.
Can you please tell me this: I'm installing a new BE6000 system that came with this problematic version of UCCX (10.5.1.10000-24). I have been testing during the weekend with 3 versions of UCCX:
-10.0.1.11001-37
-10.6.1.10000-39 and
-10.5.1.10000-24
I got the best results with version 10.0.
Can I install that version (10.0) in BE6000 instead of the one that came preinstalled (10.5.1)?
This is my first BE6000 installation and I'm not sure if this is OK?
I installed a newer version of CUCM than the one that came preinstalled because I hit bug CSCup60269 but I'm not sure If I can go to a lower version for CCX.

Ringtones and background images not available after call manager upgrade

Hi,
We have upgraded our call manager from version 8.5 to 10.5. Once after the upgrade we lost all the Ringtones and background images except the two default ringtone and background images. we got 8945 sccp phones(running 9-3-1 firmware) and 9951 sip phones(running 9-4-1 firmware). Both these phones lost these list. However the ringlist.xml is available in the tftp server with all the ringtones and the phones are pointed to the right tftp servers. I tried to restart the tftp servers and tried again, however that didn't help. we are using call manager 10.5 and h323 voice gateway. Could anyone please help on this.
Thanks
Barry

Hi Tony,
I can see the ringtone files in the call manager (osadmin>tftp file mgmt), i have also restarted the tftp services, but it didn't help. I believe you advised to re-upload the ringlist file (Ringlist.xml) and try again. I will try this and update you. Please let me know if you have any other suggestions.
Thanks
Barry

Uc560 fxo port not answering incoming calls

Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.

HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj

Cisco Catalyst 4507R+E with WS-X4748 blade, ports not working

I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade. Has anybody else seen anything like this?

I have 2 Core switches, single SUP on each.
Line cards #1 and #2 randomly stop forwarding packets, only solution is to reload the switch ( hw-module reset does not work ). I have cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin and the sympton looks the same as the described one,
although the code is newer than 3.2.2SG.
Now we are downgrading to cat4500e-universalk9.SPA.03.04.02.SG.151-2.SG2.bin to check if that solves the issue,
otherwise we´ll try removing/re-inserting the modules, and if issue persists, most probably RMA the Core1.
We´ve sent a show tech to Cisco support while the issue was happening.
Current modules on the Core switches.
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1627L48B
2    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1629L0ZY
3     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1629L1PD
5    12 1000BaseX (SFP)                        WS-X4612-SFP-E     JAE163007EO
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 30f7.0d57.80c0 to 30f7.0d57.80ef 1.1                               Ok
2 30f7.0dac.fd40 to 30f7.0dac.fd6f 1.1                               Ok
3 30f7.0dca.6c00 to 30f7.0dca.6c03 2.1 15.0(1r)SG10 03.05.00.E       Ok
5 a493.4c44.13e8 to a493.4c44.13f3 1.1                               Ok
Mod Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
3   Active Supervisor   SSO                 Active

Can't remove registered ephone in call-manager-fallback

This ephone and dn keeps registering so long as call-manager-fallback is not shutdown.
RTR001#show ephone registered
ephone-1[0] Mac:0FD4.9DA0.D415 TCP socket:[1] activeLine:0 whisperLine:0 REGISTERED in SCCP ver 6/5 max_streams=1
mediaActive:0 whisper_mediaActive:0 startMedia:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:7
IP:10.32.21.183 * 26602 SCCP Gateway (AN) keepalive 4 max_line 2 available_line 1 dual-line
port 2/0/21
button 1: cw:1 ccw:(0)
dn 2 number 4851 CM Fallback CH1 IDLE
Preferred Codec: g711ulaw
Lpcor Type: none
The MAC 0FD4.9DA0.D415 identifies port 21 on a Cisco VG224. After shutting down that voice-port, the ephone doesn't register when call-manager-fallback is enabled.

Well, that is one idea that I've already had, Linc, but I'm reluctant to use the "nuclear option" for obvious reasons. I'm actually wondering now if the Secure Cert / OD problem is affecting Profile Manager. See this thread: https://discussions.apple.com/message/23686348#23686348

CPIC-CALL Transaction program not registered Error while creating RFC Desti

Hi All,
I am trying to create a new RFC Destination.
Details I have provided are..
1.RFC Destination Name
2.Connection Type - TCP/IP
3.Description
4. Activation Type - Registered Server Program.
5.Program Id.
6. Gateway Host and Gateway Service.
But When I Test the connection, I am getting the following error.
" program xyz not registered / CPIC-CALL: 'ThSAPECMINIT'# Transaction program not registered"
However I was able to create and connect RFC Destinations successfully previously.
I am not SAP guy. Could someone help resolve this issue.
Thanks,
Phani

hi Sekhar,
I request you to please help me out in this issue. I am getting similar kind of problem. I am trying to replicate the customer from CRM to R/3 and i get a bdoc message in SMW01 that "RFC connection failed please press the save button again". When the basis team further investigated they came up with the below error..
User: CRREMOTE (Client: 071)
Destination: OCR (handle: 1, , )
Error RFCIO_ERROR_SYSERROR in abrfcpic.c : 1462
CPIC-CALL: 'ThSAPECMINIT'
Transaction program not registered
DEST =OCR
HOST =%%RFCSERVER%%
PROG =dpssrfc
Trace file opened at 20061121 140451 EST SAP-REL 640,0,109 RFC-VER
3 804778
resize I/O buffer to 28000 bytes
>>>> [2] MQ_LINK : TCP <ac: 3> K %%RFCSERVER%% >>> OPEN
{45632F14-288E-0046-0000-0000A888A7AA}-
======> CPIC-CALL: 'ThSAPECMINIT'
can you please tell me where can be probelm. Regarding your message, where can i get the communication channel to assign the program id.
Awaiting your reply,
Thanks & Regards,
Yogesh

Hunt Group with Pots lines in Call Manager

Hello all. I have a site with 12 Pots lines. It is all configured via Call Manager. We are using mgcp. I asked the telco to setup the numbers to hunt which they said they did but still when I call the main number second time it just rings and eventually get some voicemail that is not from the call manager. I think I need to setup Hunting in the Call Manager? Is that correct?
Line Group --> Add the extensions in here and set them up to hunt?
Hunt List --> Create a Hunt list and associate a Line Group with it?
Hunt Pilot --> I add all the extensions in here?

Let's take one step back. What are you trying to accomplish? I am assuming you want to market one number but have the ability to accept multiple calls on that number. If that is the case, having the telco set up a hunt is the way to go.
Beyond that, where do you want those calls from the PSTN to route? Are you wanting those calls to ring a hunt group on your side? If so, you will need to do the following:
     1. Configure a Line group. (Call Routing -> Route/Hunt -> Line Group) This is where you will be adding the extensions. You will also need to specify a distribution algorithm. The distribution algorith, is where you will be choosing how you want the extensions to ring. For instance, if you set the DA to broadcast, every extension in the line group will ring at the same time. Click Help --> this page, while you are in the line group configuration page to get more information about the settings you can modify and different algorithms you can use.
     2. Configure a Hunt List. (Call Routing -> Route/Hunt -> Hunt List) You will need to create a new Hunt List and add your line group to it. The hunt list is evaluated in a top down fashion. You can get pretty tricky with multiple line groups with different distribution algorithms in your hunt list, but if you just want something basic,just add the line group you made.
     3. Configure the Hunt Pilot. (Call Routing -> Route/Hunt -> Hunt Pilot) The hunt pilot will be the dialed number that triggers the hunt group. Make sure you select all the required settings. You will be selecting the hunt list you just made in this configuration page. Be sure to set a maximum hunt timer and final destination so that the calls do not just ring forever. You can get pretty granular with the settings in here. Reference the help --> this page document for more information.
     4. POINT THE FXO PORTS TO THE HUNT PILOT. This is very important. Calls to your analog lines will not trigger the hunt group unless you point the ports to the Hunt Pilot. If you are using MGCP/SCCP you will need to enter the hunt pilot in the "Attendant DN" field for EVERY FXO port. If you do not enter a value here, CUCM will have no idea what to do when the port rings. It will not answer the call if there is no value specified. This would explain why your calls were ending up with the telco voicemail service; CUCM was never answering the call.
If you completed the above steps correctly, you should be able to call the main number multiple times and have the calls go to a hunt group on your side, no matter which line the call ends up coming in on.
Let me know if you have any questions, this can be kind of tricky at first.
PS, if the calls were going to a voicemail that wasn't from Call Manager (Unity Connection) call the telco and have them remove voicemail service from the lines, assuming you have configured Unity Connection to handle that.
Hope this helps,
Dallan

Program not registered - RFC to J2EE (local machine)

I have a local install of WAS on my laptop using MSSQL 2000. I am trying to integrate local portal into a BI system.
1. I completed SLD configuration of local J2EE
2. As part of local SLD config I specified a BW7 system as data supplier
- entered BW7 host & gateway
- kept default settings for "configure data supplier targets" (i.e: sld/active=TRUE)
3. In Visual composer I successfully triggered SLD data transfer
4. In Visual Composer I specified a JCo RFC Provider to the BW7 system I want to access.
5. If I go to BW7 and goto tcode SMGW -> GOTO -> Logged on client, I see 2 pair of entries for JCo RFC provider
with the following settings
- system type: Registered Server (REGISTER_TP)
- state: connected
- LU name & Host Name = J2EE Host name w/ last 4 characters truncated. Only first 8 characters appear.
- TP Name: 2 entries = SLD_UC & 2 entries = SLD_NUC. So a total of 4 connections. My understanding is that TP Name is supposed to = Registered Server Program
6. In BW7, I have an RFC w/ Registered Server Program setting and program ID = JCo RFC Provider program ID
7. In BW7 RFC & JCo RFC the host & gateway settings are the same, they both refer to the BW7. THIS IS THE PART WHERE I AM UNSURE. I would have thought that the host & gateway settings of BW7 RFC would refer to Local J2EE engine. AND I DON'T KNOW WHAT THE GATEWAY IS FOR LOCAL J2EE.
8. In BW7 when I try to test the RFC, I get errors:
- Logon Connection Error
- program <...> not registered / CPIC-CALL: 'ThSAPOCMINIT' Tran
- ERROR: program <...> not registered
- DETAIL: TP <...> not registered
- COMPONENT: SAP-Gateway
- MODULE: gwr3cpic.c
- RETURN CODE: 679
- SUBRC: 0
- RELEASE: 700
- VERSION: 2
9. I completed step 1 & 2 of RSPOR_SETUP
- Step 1 <Create RFC Destination in J2EE engine> messages:
No Authorization to SMGW
Profile parameter login/create_sso2_ticket is not set to 2
Check of RFC destination <...> with RFC_READ_TCPIP_DESTINATION successful
- Step 2 <Create RFC destination to Portal> messages:
No Connection
Option Send SSO tickets not active (see documentation)
RFC CALL RFC_PING, destination <...> failed with sy-subrc =2
There a little something missing. Hope u gurus can help, lost a weekend over this.

Hello,
we get the same message (program ... not registered, COMPONENT: SAP-Gateway) in sm59, when checking the TCP/IP connection. We got it, after we changed the user name in the Visual Administrator.
Does anyone know with which tool and where the program can be registered. (The connection has no user name (connection by SAP ticket)).
Best regards,
Thomas

WS6608 blade - port not registering to Call Manager

Similar Messages

Maybe you are looking for