Xilinx version availability for labview fpga compile

While trying to compile a Labview vi for target NI PXI 7831R, at first I didn't have
any Xilinx compile so I asked my network guy to instal it.  Now it complains
that it needs 10.1 when 11.5 is available.  I asked him to install the 10.1 and
he did but it isn't available to the NI FPGA compile worker.  How do I solve
this?
thanks

Hi DonQuixote,
You are correct in that the PXI 7831R requires Xilinx Compile Tools 10.1.  This is because this card has a Vertex II chip.  You can read more about Xilinx requirements here: http://ae.natinst.com/public.nsf/webPreview/A4B20D58C051DFB386257A56007BB0B2?OpenDocument .
Have you uninstalled version 11.5?  What version of LabVIEW do you have?  Are you recieving an error or some other message?  If so, please post a screenshot.  
Thanks!
Dayna P.

Similar Messages

  • C API version required for LabVIEW FPGA 2011

    What is the verison of the C API that will work with LabVIEW FPGA 2011?
    Solved!
    Go to Solution.

    I would guess this one: http://www.ni.com/download/fpga-interface-c-api-2.0/2616/en/
    The version numbers appear to start with years in 2012.  This is the highest version I could find before 2012 and it was released in August of 2011.  That time coincides with the annual NI Week festivities where a large portion of the software/hardware is released.  It's a small download so it shouldn't be difficult to download and try it out.
    But, you'll still need LabVIEW for FPGA development according to this white paper: http://www.ni.com/white-paper/9036/en/

  • IS CLIP supported by Xilinx Spartan3E driver for LabVIEW 8.6?

    IS CLIP supported by Xilinx Spartan3E driver for LabVIEW 8.6?
    For HDL interface node, the enable chain and multi clock domain is difficult to understand
    Solved!
    Go to Solution.

    Reidl,
    Thank you for your answer.  How do I uninstall my current version?  I have looked in "Add or Remove Programs," but I don't see anything under "Xilinx" or "Spartan."  I do see an entry for "National Instruments Software."  However, when I click "Change / Remove" I don't see any entries for the Spartan Board.
    I tried running the installation program, and I received the following message:
    The NI LabVIEW FPGA Support for Spartan-3E 1.1.0 installation has failed with the following error.
    You have a higher version of NI LabVIEW FPGA Support for Spartan-3E in your system.  You must uninstall it before installing this again.
    What is the latest version number?  How do I check what version I currently have?
    Thanks,
    James Carroll 

  • Need spartan 3e driver for LabVIEW FPGA 2011

    Hello,
    I'm looking for Spartan-3E driver for Windows 7 LabVIEW FPGA 2011.
    Thank you

    Thank you for all the helps. I do appreciate that.
    By the way, I'm wondering the latest driver on NI is used for Labview FPGA 2012 or 2012sp1?
    Just in case our department would purchase the latest version of Labivew in the near future.
    Thank you again and have a nice day.
     

  • Is there a pc version available for ibooks.

    is there a pc version available for ibooks.
    where does the .itmsp files reside in itunes and how do i donwload it.
    I am a novice on the apple peoducts.
    Need help. Thanks.
    regards
    PP

    No, there is due to be an iBooks reader for OS X Mavericks, but as yet no indication of if or when that will be extended to earlier versions of OS X, let alone to Windows PCs.
    From the look of this, .itmsp is the format publishers use to upload content to the iTunes Store, but not what the user downloads. iBooks files have the extension .epub. Non-protected iBooks can be read in any suitable reader, protected books need an iBooks app.
    tt2

  • Latest version available for Oracle Forms and Reports in 11g AS

    Deaer Friends,
    Please let me know latest version available for Oracle Forms and Reports in 11g Application Server and let me know whether it is supported in Windows - 64 Bit Platform
    Regards,
    DB

    DB,
    Oracle Forms and Reports 11g Release 2 (11.1.2) is the most recent forms and reports.
    If you're on 11.1.1.x (for example 11.1.1.5 or 11.1.1.4), please refer to http://docs.oracle.com/cd/E24269_01/doc.11120/e23975/upgrade_from_r1.htm for upgrade procedure.
    Otherwise, if you're installing it brand new, download Oracle Forms and Reports 11gR2 (11.1.2.0.0 from http://www.oracle.com/technetwork/developer-tools/forms/downloads/index.html
    HTH,
    Raj Mareddi
    http://www.freeoraclehelp.com

  • Is there a downloadable iTunes Version Available for OS Windows ME?

    Is there a downloadable iTunes Version Available for OS Windows ME? If so, please let me know. Here is the situation.
    I would like to import some classical music that I have in my Windows Media Player to iTunes so that I could burn the music to a CD.I am unable to burn the music in the WMP program because the Adaptec Easy Cd Creator is not compatible with the newer version of the WMP. Also, the Roxio program is not available for the older version of Windows ME. Any help would be appreciated in this matter.
    Thank you.

    If there is, folks running OS 8 and previous who hang out here might not know about it. But folks in the iTunes for Windows forum probably used to run it, and can help out a lot:
    Discussions > iTunes for Windows

  • DCT for Labview fpga

    Hi,
    I have problems based on dct for labview fpga. I get the project example from this link https://decibel.ni.com/content/docs/DOC-8202. I run the project in labview and its run succesfully. After that, I try to use a different vhdl code for the CLIP (in labview) that I get from open cores (http://opencores.org/project,dct_idct). I rewrite the fpga.vi by inserting a new vhdl code in the CLIP. When I run the project, there are no errors. However, the compressed image is not display. I check the output values from the Read from FPGA block at the host.vi and it shows zero values at all time. I try to debug, but still don't get the solution. Anyone expert please help me. Thanks in advance.

    Hey Troy,
    Have a look at the attached front panel design that will be compatible in FPGA.
    Hopefully it helps!!
    Aashish M
    Applications Engineer
    National Instruments
    http://www.ni.com/support/
    Attachments:
    FPGA_CALC.vi ‏22 KB

  • What's the latest filmware version available for N...

    What's the latest filmware version available for Nokia 6610?

    4477 wrote:
    Anyone else?
    As long as you refer to 6610 NHL-4U rather than 6610i RM-37.
    Happy to have helped forum with a Support Ratio = 42.5

  • Labview FPGA compile stuck at "Place and Routing"

    I am using LabVIEW 2010 SP1 32-bit FPGA module.  I've built a very large program that was first done back using LabVIEW 8.6, so I have several years experience on LabVIEW FPGA.
    When I say it's a large program, I mean that a several times over the last couple years I've tried to add more functionality that has failed to compile do to not enough space on the target or timing restraints.  My target has mostly been the PCI/PXI NI-7813R.  Due to the nature of our product, a lot has to be done on one FPGA board.
    When I do go "over the limit" the compile (after a couple hours) fails and tells me that there's just not enough room on the 7813.
    Recently, however, I added some more code, thinking the odds were good that it might push me over the edge.  However, the compile never fails.  Unfortunately, it never stops either.  It gets to the "Placing and routing" portion of the compile and just stays there.  When I say stays there, I mean I've run it over night, and when I check it the next morning, the "Elapsed time" is over 10 hours, and still counting up.  The device utilization and estimated timing numbers are all under max.  And I see no errors in the report so far that I'm used to seeing.  Like I said, it just keeps compiling.
    I've attached the Xilinx log.  It looks much like the log before I added the extra code, except it just stops logging with reporting any useful error.
    Anyone have an idea what I could be doing wrong?
    Thanks,
    Rick
    Attachments:
    XilinxLog.txt ‏3936 KB

    tannerite,
    Thanks for your response.
    I added code that measures the "on time" of incoming DIO pulses.  If the pulses are HIGH for one given amount of time (eg. 60[+/- 5] usecs) it means one thing, if HIGH for a different amount of time (eg. 120[+/- 5] usecs) it means something else.  Generally speaking, I just keep a tick count between the rising and falling edge of the pulse, and use the "In Range and Coerce" from the Comparison Functions palette to check where the count lies.
    When it compiled successfully, I duplicated the above code for 10 seperate DIOs.  Then I realized I needed to monitor 20 DIOs.  It was when I added the code for these extra 10 DIOs that I got the "forever" compile.  The compile problem occurs everytime I try to compile with the extra 10 DIO code in place.  As an experiment, I just added 4 extra DIOs, i.e. code to monitor a total of 14 DIOs.  This causes the same compile problem.
    And yes, the compile seems to hang in the same place every time it hangs.  Like I said, I wouldn't be surprised if I'm just beyond the available resources available.  But when I've done this in the past, the compile does finally fail, and I get a useful error message.  I've never seen it go "forever".
    Thanks ahead of time for any insight you might have.
    - Rick

  • Need SPARTAN 3E board Driver for Labview FPGA 8.5 !!!!!! Thx

     HI!!I need the spartan 3e driver for labview 8.5(not for labview 8.6) for school useI try to download it from ftp://ftp.ni.com/outgoing/NISPARTAN3ELV85.zip
    but this link is dead now. Could somebody send this driver to [email protected] PLZ? Thank you a lot for all in advance
    Solved!
    Go to Solution.

    Hello,
    I'm looking for same (Labview FPGA 8.5 for Spartan 3E). But it isn't available on related url now. I'll be glad if someone can help to find driver.
    Best regards, 

  • Can anyone provide me the suitable material for labview fpga &labview real time??

    Message Edited by Sithu on 05-27-2008 04:32 AM

    The following link includes training material for both LabVIEW Real-time and LabVIEW FPGA.
    http://zone.ni.com/devzone/cda/tut/p/id/6929
    If you are new to LabVIEW you should start from the LabVIEW Basics material available at the following link.
    http://cnx.org/content/col10241/latest/
    KostasB
    NIUK Applications Engineering

  • How to find the servlet, jsp version available for SunOne 7 webserver

    hi ,
    I am looking for a command that can say the version of servlet, JSP container in Sun One7 webserver.
    as in weblogic we can do by command
    java weblogic.version -verbose
    is similar type of command is available for SunOne 7 web server

    Hi,
    Ask BASIS person to check the JMS driver which is installed on XI through visual admin.
    Thnx
    Chirag

  • Is Oracle 10.2g the most current version available for z/OS

    Hi
    I am a seasoned z/OS system programmer but an Oracle Newbie. When I go to the download tab at oracle.com and select 'database 11g' under databases, the only item I see for z/OS is 10.2g. Is this the latest version of Oracle Database for z/OS?
    Thanks for any guidance.

    Is this the latest version of Oracle Database for z/OS?11gr2 isn't available for z/OS.
    Release Schedule of Current Database Releases - 742060.1
    11gR2 for IBM z/OS or z/Linux?
    -Anantha
    Added Metalink Doc info.

  • Windows98SE / MJPEG / Newest QT Version available for Win98SE

    Hello, Multi Part Question.
    (Main question).
    I have a digital camera (canon A540 Powershot) records video in MJPEG, MOTION JPEG, (AVI wrapper I guess you call it), format
    is there a QT version that will play these files on my Windows98SE.?.
    (Next Question).
    What is the LAST version of QT available for Win98SE 6.5.2 ?.
    (Last Question).
    for QT 6.5.2, Is there some where I can read the file types it supports ?..
    Thanks a bunch in advance

    Hi yah Kirk, thanks for that BUT with the last question in my post you can see I found that already, and doesn't answer ANY of my questions, to my knowledge or that I can see , read or find.
    that only points me to 6.5.2 which I do believe to be the last available for win98se, but had to ask to be sure, and it doesn't show anything about my questions.
    Which I have infact come across another question.
    I found on the canon web site that they HAD a QT 6.5 to not only Play but EDIT the video files, is that QT 6.5 a full version or some how different than the QT 6.5.2 ?. I am thinking the QT 6.5.2 is like a web browsing along with the qt player(view only) enhancement. while the Canon QT 6.5 must be some sort of full version .... probably should have asked that, because I don't want anyone to get confused or of track of the original post...:)

Maybe you are looking for

  • GR and IR posted to different GR/IR accounts

    Hello Gurus, We have an issue that GR and IR are posted to two different GR/IR accounts against a PO. This was because Vendor reconciliation account was changed after the initial GR posting. Please advise how to rectify. Many Thanks, Leelendra

  • How to configure one Listener for 2 databases on the same server

    Hello all, Please, I am stuck as with my application server which requests the port 1521. I want to configure the repository to make use of the port 1521 which is also shared by another database on the server. Regards, Nadine

  • DB connect error in pre-migration check (EP5.0 SP6- EP6 SP16)

    Hello,       I am working on migration (EP 5.0 SP 6--> EP 6.0 SP 16). I have created a EP 5 System ,While I am checking for connectivity, (http://nw04:5000/sp) it displays an error message. Here is a string I have used for connection. URL: jdbc:sap:s

  • Re: Printer Problems after 10.4.6 Update

    I cannot find a solution to my printing problems since having updated to 10.4.6 I am using an HP Deskjet 3620 which worked fine with 10.4.5 Since the update, my printer settings have disappeared. When I try to add a printer, all I get is an error mes

  • A certain real estate web site loads, but not the photos. IE does it OK.

    www.domain.com.au is a real estate sales page. Most of the site loads but not the photos, just a word 'House' in its place. I tried same site on IE and it all loaded correctly.