Connect Inside to Outside in ASA 5505
Hi there,
I have a test ASA 5505 with the setting below:
How can I connect to the internet (Vlan 1 to VLan 11)
TestASA5505# show run
: Saved
ASA Version 8.2(4)
hostname TestASA5505
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 11
interface Ethernet0/1
switchport access vlan 3
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.99.1 255.255.255.0
interface Vlan11
nameif outside
security-level 0
ip address 192.168.1.4 255.255.255.0
boot system disk0:/asa824-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
route outside 0.0.0.0 255.255.255.255 192.168.1.4 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.99.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.99.3-192.168.99.30 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption 3des-sha1 aes128-sha1 aes256-sha1 rc4-md5
webvpn
username admin password S1xyD1w.ZbjUT1yX encrypted privilege 15
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:096682b0996d6a1cad76597c01ffe5e2
: end
TestASA5505#
Thank you in Advance for your time
Hi,
What device is in front of the ASA?
Is there some ADSL modem doing NAT and providing Internet connection or something?
One obvious problem in the above configuration is the route
route outside 0.0.0.0 255.255.255.255 192.168.1.4 1
Its not actually even a default route and furthermore its pointing to the ASA itself
It should be something like this
route outside 0.0.0.0 0.0.0.0 192.168.1.x
Where the 192.168.1.x is the IP of the device providing the Internet connectivity to the ASA (Since ASA "outside" interface is using private IP address range)
If there ASA doesnt need to do any NAT then you could also add this
access-list INSIDE-NAT0 permit ip 192.168.99.0 255.255.255.0 any
nat (inside) 0 access-list INSIDE-NAT0
Also your DHCP configurations dont have any DNS servers defined.
dhcpd dns
- Jouni
Similar Messages
-
Unable to ping device behind Cisco 3750 on the same inside VLAN via Cisco ASA 5505 Anyconnect VPN
Hi Guys,
I've been stuck with this for the last 2 days, and I thought to try and use Cisco's forum, I setup my home DC, and started having problems once I moved a Cisco 5505 behind a Cisco 1841 router (I wanted to eventually test DMVPN live on the internet,) I was no longer able to ping some devices, then as soon as I introduce a collapsed core/distribution switch, I'm also no longer able to ping the devices behind the Cisco 3750, I've attached a network diagram and the ASA running-config.
Everything seem fine internally with the exception of an intermittent network connectivity with a Citrix NetScaler VPX running on a VMware ESXi.
For some odd reason, I am able to ping the following, with no issues.
Cisco 3750 SVI (192.168.1.3)
CentOS web server (connected directly to the Cisco ASA 5505)
I have checked and enable the following:
Nat Exemption
Sysopt connection permit-vpn
ACL's
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
Added ICMP in the inspection policy
Packet-capture - Only getting echo requests.
Thanks in advance!Hi,
I believe you have the problem with your no-nat configurations..... you to exempt NAT for the traffic from 172.16.10.0 (Anyconnect VPN pool) to 192.168.1.0/24 (Inside LAN) to make this work
object network acvpnpool
subnet <anyconnect VPN Subnet>
object network insidelan
subnet <inside lan subnet>
nat (inside,outside) source static acvpnpool acvpnpool destination static insidelan insidelan
Make sure that you are able to reach the GW/Inside ip adress of the firewall from LAN machine.... all routing in place properly..... Thanks!!!
Regards
Karthik -
ASA 5505 unable to connect inside or outside
Hello,
I'm extremely new to router configurations, and am attempting to configure a backup ASA 5505 to use as a temporary access point in the event that our main ASA becomes unavailable. What I have done is loaded the running config from our main ASA onto the backup, and have made changes to necessary routes, IPs, etc. I can connect to it from a remote computer without problem, but I cannot access any of our servers, nor can I access the internet. I have also tried modifying the access list and NAT rules every which way from Sunday, but I still cannot get this thing to allow any information through. I keep getting "failed to locate egress interface for UDP from outside" errors.
We are using Cisco AnyConnect to connect , and mind you, since the config for this backup ASA was taken from our main, it still has the original certificate info and profiles. I was told that this wouldn't matter, but I thought I should mention in case I need to remove any of it from the config.
Here is part of the config file. I took out some information, but tried to keep it understandable. If anyone could point me in the right direction, it would be greatly appreciated!
ciscoasa# show running-config
: Saved
: Serial Number: xxxxxxxxxxx
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)
hostname ciscoasa
domain-name domain
enable password encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd encrypted
names
ip local pool pool1 x.x.9.22-x.x.9.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address x.x.8.10 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.237 255.255.255.248
boot system disk0:/asa922-k8.bin
boot config disk0:/startup-config
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group Default
name-server x.x.8.100
domain-name domain
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network pool1
subnet x.x.9.0 255.255.255.0
object network outside-network
host x.x.x.237
object network Remote-Network
subnet x.x.8.0 255.255.255.0
object network local
object network obj-x.x.9.24
host x.x.9.24
object-group network Outside-Network-Group
description Outside Network Group
network-object x.x.x.232 255.255.255.248
object-group network Inside-Network-Group
description Inside Network Group
network-object x.x.8.0 255.255.255.0
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list NONAT extended permit ip x.x.8.0 255.255.255.0 x.x.9.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 30000
logging buffered debugging
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
flow-export destination inside x.x.8.132 2055
flow-export template timeout-rate 1
flow-export delay flow-create 50
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
asdm image disk0:/asdm-722.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static any any destination static pool1 pool1 no-proxy-arp route-lookup
nat (inside,outside) source static any any destination static Remote-Network Remote-Network no-proxy-arp route-lookup
nat (outside,outside) source dynamic pool1 interface
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 x.x.x.232 1
route inside x.x.11.0 255.255.255.0 x.x.11.1 1
If you have any questions, or need any other information, please let me know.
Thanks!Am I posting this in the wrong section? Anyone?
-
How to tracert to outside in ASA 5505/5520?
Hi,everybody
The tracert issue have troubled me for a long time. I don't know how to deal with it. Pls give me some advice. Thanks!
Following is the details.
The network have two firewall(ASA 5505,ASA 5520) placed in different cities. And all person inside can reach the internet.
The problem is that we can ping internet IP from inside but can not tracert outside IP. It always reply us "request time out".
Why?
Somebody know that?Hello,
I know this has been a long time ago, but I'm facing the same issue in the ASA. Weirdly enough, I can reach the destination using traceroute with no problem, but I can't see the path to it. I pasted the result below.
I also checked my ASA configuration and the only setting that is not present is the "match any " for the "class-map class_default", because when I enter "class-map class_default" I get the following warning:
ASA(config)# class-map class-default
ERROR: % class-default is a well-known class and is not configurable under class-map
Can you guys help me? I posted below the tracert output and the concerned configuration. I can't find the misfit and I already checked most of the configuration forums.
C:\>tracert www.google.com
Tracing route to www.google.com [173.194.79.104]
over a maximum of 30 hops:
1 <1 ms <1 ms <1 ms 10.0.0.1
2 * * * Request timed out.
3 * * * Request timed out.
4 * * * Request timed out.
5 * * * Request timed out.
6 * * * Request timed out.
7 * * * Request timed out.
8 * * * Request timed out.
9 * * * Request timed out.
10 * * * Request timed out.
11 * * * Request timed out.
12 * * * Request timed out.
13 * * * Request timed out.
14 * * * Request timed out.
15 * * * Request timed out.
16 * * * Request timed out.
17 * * * Request timed out.
18 * * * Request timed out.
19 * * * Request timed out.
20 * * * Request timed out.
21 * * * Request timed out.
22 * * * Request timed out.
23 212 ms 212 ms 212 ms pb-in-f104.1e100.net [173.194.79.104]
Trace complete.
---Router configuration
icmp unreachable rate-limit 10 burst-size 5
object-group service ICMP_Return
service-object icmp echo-reply
service-object icmp time-exceeded
service-object icmp traceroute
service-object icmp unreachable
service-object icmp6 echo-reply
service-object icmp6 time-exceeded
service-object icmp6 unreachable
access-list IF_outside_access_in remark ICMP Return
access-list IF_outside_access_in extended permit object-group ICMP_Return any any
access-group IF_outside_access_in in interface IF_outside
class-map class_default
!--- This does not exit -> match any
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class class-default
set connection decrement-ttl
service-policy global_policy global -
Forward 3 inside IP using the same port to one outside IP ASA 5505
Ok, so I have 3 cameras 172.20.101.15-17 all listen on port 7000. I want to forward them to a single outside IP, but when the user connects I need them to come in on ports 7001, 7002, 7003.
I have forwarded ports before, but never in this fashion, and I have no clue how to do so.Hello Shaun,
Let's say you are running a version higher than 8.3 and that the public IP is 8.8.8.8
object network Outside_IP
host 8.8.8.8
exit
object network Internal_server_1
host 172.20.101.15
nat (inside,outside) static 8.8.8 service tcp 7000 7001
exit
object network Internal_Server_2
host 172.20.101.16
nat (inside,outside) static 8.8.8 service tcp 7000 7002
exit
object network Internal_Server_3
host 172.20.101.17
nat (inside,outside) static 8.8.8 service tcp 7000 7003
Of course create the ACL's as needed,
Regards, -
Hi,
i have problem configuring DMZ to access outside.
I'm not able to ping from DMZ network to DMZ interface (gateway) neither am i able to contact the internet with DMZ hosts
I'm able to ping from LAN to LAN gateway (inspect ICMP service policy)
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.254 255.0.0.0
interface Vlan2
description Connection to Internet
nameif outside
security-level 0
pppoe client vpdn group Dial_Belgacom
ip address pppoe setroute
interface Vlan12
description DMZ
nameif DMZ
security-level 50
ip address 172.20.1.254 255.255.255.0
access-list DMZ_access_in extended permit ip object NetworkDMZ any
access-list DMZ_access_in extended deny ip object NetworkDMZ any
object network in-out
nat (inside,outside) dynamic interface
object network DMZ-Out
nat (DMZ,outside) dynamic interface
access-group inside_access_in in interface inside
access-group DMZ_access_in in interface DMZ
Thanks,
ChristopheDo you have the security plus license installed?
Are using a single ASA interface? if so, is that port configured to be a trunk?
Have you tried a shut / no shut on the DMZ interface?
Have you tried removing the configuration from the DMZ interface and re adding it?
Have you made 100% sure that the IP you are testing from in the DMZ network is within the subnet 172.20.1.0/24?
What is between the ASA and the test PC? (switch, L3 switch, router...etc.)
If you configure a port on the ASA to be in vlan 12 and connect a PC directly to that port, do you get a successful test?
Please remember to select a correct answer and rate helpful posts -
after tried to setup access list, it return drop in packet tracer and can not ping outside router too
is there an configuration example to show allow a subnet of class C IP address to surf internet in Cisco ASA ?
assume all works in GNS3, expect initial network setup too
inside outside
router A 192.168.1.2 <--->switch <---> 192.168.1.1 ASA 192.168.1.4 <---> switch <---> router B 192.168.1.3
ASA version: 8.42
when i try the following command,
ASA
conf t
interface GigabitEthernet 0
description INSIDE
nameif inside
security-level 0
ip address 192.168.1.1 255.255.255.0
no shut
end
conf t
interface GigabitEthernet 1
description OUTSIDE
no shutdown
nameif outside
security-level 100
ip address 192.168.1.4 255.255.255.0
no shut
end
conf t
object network obj_any
subnet 0.0.0.0 0.0.0.0
nat (inside,outside) dynamic interface
end
conf t
access-list USERSLIST permit ip 192.168.1.0 255.255.255.0 any
access-group USERSLIST in interface inside
end
Router A
conf t
int fastEthernet 0/0
ip address 192.168.1.2 255.255.255.0
no shut
end
Router B
conf t
int fastEthernet 0/0
ip address 192.168.1.3 255.255.255.0
no shut
end
ASA-1# packet-tracer input inside tcp 192.168.1.1 1 192.168.1.4 1
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.1.0 255.255.255.0 inside
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
<--- More --->current config can not ping, one of packet tracer allow all, another packet tracer drop
can not ping between Router A and Router B
ASA-1# packet-tracer input inside tcp 192.168.1.2 1 192.168.3.3 1
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.3.0 255.255.255.0 outside
Phase: 2
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 3
Type: NAT
Subtype:
Result: ALLOW
Config:
object network DYNAMIC-PAT
nat (inside,outside) dynamic interface
Additional Information:
Dynamic translate 192.168.1.2/1 to 192.168.3.4/311
<--- More --->
<--- More --->
Phase: 4
<--- More --->
Type: IP-OPTIONS
<--- More --->
Subtype:
<--- More --->
Result: ALLOW
<--- More --->
Config:
<--- More --->
Additional Information:
<--- More --->
<--- More --->
Phase: 5
<--- More --->
Type: FLOW-CREATION
<--- More --->
Subtype:
<--- More --->
Result: ALLOW
<--- More --->
Config:
<--- More --->
Additional Information:
<--- More --->
New flow created with id 14, packet dispatched to next module
<--- More --->
<--- More --->
Result:
<--- More --->
input-interface: inside
<--- More --->
input-status: up
<--- More --->
input-line-status: up
<--- More --->
output-interface: outside
<--- More --->
output-status: up
<--- More --->
output-line-status: up
<--- More --->
Action: allow
<--- More --->
ASA-1# packet-tracer input outside tcp 192.168.3.3 1 192.168.1.2 1
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.1.0 255.255.255.0 inside
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
<--- More --->
Drop-reason: (acl-drop) Flow is denied by configured rule
<--- More --->
ASA-1#
ASA-1# sh run |
: Saved
ASA Version 8.4(2)
hostname ASA-1
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0
description INSIDE
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface GigabitEthernet1
description OUTSIDE
nameif outside
security-level 0
ip address 192.168.3.4 255.255.255.0
interface GigabitEthernet2
shutdown
no nameif
no security-level
<--- More --->
no ip address
<--- More --->
<--- More --->
ftp mode passive
<--- More --->
object network DYNAMIC-PAT
<--- More --->
subnet 192.168.1.0 255.255.255.0
<--- More --->
access-list 101 extended permit icmp any any echo-reply
<--- More --->
access-list 101 extended permit icmp any any source-quench
<--- More --->
access-list 101 extended permit icmp any any unreachable
<--- More --->
access-list 101 extended permit icmp any any time-exceeded
<--- More --->
access-list ACL-OUTSIDE extended permit icmp any any
<--- More --->
pager lines 24
<--- More --->
mtu inside 1500
<--- More --->
mtu outside 1500
<--- More --->
icmp unreachable rate-limit 1 burst-size 1
<--- More --->
no asdm history enable
<--- More --->
arp timeout 14400
<--- More --->
<--- More --->
object network DYNAMIC-PAT
<--- More --->
nat (inside,outside) dynamic interface
<--- More --->
access-group ACL-OUTSIDE in interface outside
<--- More --->
timeout xlate 3:00:00
<--- More --->
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
<--- More --->
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
<--- More --->
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
<--- More --->
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
<--- More --->
timeout tcp-proxy-reassembly 0:01:00
<--- More --->
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
<--- More --->
user-identity default-domain LOCAL
<--- More --->
no snmp-server location
<--- More --->
no snmp-server contact
<--- More --->
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
<--- More --->
telnet timeout 5
<--- More --->
ssh timeout 5
<--- More --->
console timeout 0
<--- More --->
threat-detection basic-threat
<--- More --->
threat-detection statistics access-list
<--- More --->
no threat-detection statistics tcp-intercept
<--- More --->
<--- More --->
<--- More --->
prompt hostname context
<--- More --->
no call-home reporting anonymous
<--- More --->
call-home
<--- More --->
profile CiscoTAC-1
<--- More --->
no active
<--- More --->
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
<--- More --->
destination address email [email protected]
<--- More --->
destination transport-method http
<--- More --->
subscribe-to-alert-group diagnostic
<--- More --->
subscribe-to-alert-group environment
<--- More --->
subscribe-to-alert-group inventory periodic monthly
<--- More --->
subscribe-to-alert-group configuration periodic monthly
<--- More --->
subscribe-to-alert-group telemetry periodic daily
<--- More --->
crashinfo save disable
<--- More --->
Cryptochecksum:8ee9b8e8ccf0bf1873cd5aa1efea2b64
<--- More --->
: end
ASA-1# -
FTP issue inside to outside on ASA
we have user who are on DHCP and would require some user to access FTP server which is on the outside.
However being on DHCP it is not possible so suggested to use a internal server and ftp from their but it still doesn't work after allowing through the ASAdid you configure "inspect ftp"?
-
ASA 5505 L2TP client connect problem
I am trying to connect MS l2tp clients to asa 5505 and am unsuccessful. I have tried the ASDM VPN Wizard as well as CLI and missing something. I have attached my current config. My client hits the interface and logs an error 713048 Error processing payload: Payload ID: 1. I know I am missing something simple, but I just can't see it. HELP!!!! Please
ASA configuration needs to have the following configured ...
- The preshared key needs to match the one configured in the windows client setup.
- The authentication needs to match what you have configured on the client, pap or chap ..
If chap is configured you need to readd the usernames to the ASA with the mschap keyword
at the end .. e.g
SV2-2(config)# username msclient password msclient mschap
- The DefaultRAGroup needs to be configured with the preshared key and point to a policy
that include this vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
The complete config is below ... DefaultRAGroup will be used if the preshared key is
added and nothing is specified on the client..
tunnel-group DefaultRAGroup general-attributes
address-pool vpnpool
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
tunnel-group DefaultRAGroup ppp-attributes
authentication pap
authentication ms-chap-v2 -
Hello everyone,
First off, I apologize if this is something that I can google. My knowledge of network administration is all self-taught so if there is a guide to follow that I've missed please point me in the right direction, its often hard to Google terms for troubleshooting when your jargon isn't up to snuff.
The chief issue is that when pinging internal devices while connected to the results are very inconsistent.
Pinging 192.168.15.102 with 32 bytes of data:
Reply from 192.168.15.102: bytes=32 time=112ms TTL=128
Request timed out.
Request timed out.
Request timed out.
We've set up a IPSec VPN connection to a remote Cisco ASA 5505. There are no issues connecting, connection seems constant, packets good etc. At this point I can only assume I have configuration issues but I've been looking at this for so long, and coupled with my inexperience configuring these settings I have no clue where to start. My initial thoughts are that the LAN devices I am pinging are not sending their response back or the ASA doesn't know how to route packets back?
Here's a dump of the configuration:
Result of the command: "show config"
: Saved
: Written by enable_15 at 12:40:06.114 CDT Mon Sep 9 2013
ASA Version 8.2(5)
hostname VPN_Test
enable password D37rIydCZ/bnf1uj encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.15.0 internal-network
ddns update method DDNS_Update
ddns both
interval maximum 0 4 0 0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
description VLAN to inside hosts
nameif inside
security-level 100
ddns update hostname 0.0.0.0
ddns update DDNS_Update
dhcp client update dns server both
ip address 192.168.15.1 255.255.255.0
interface Vlan2
description External VLAN to internet
nameif outside
security-level 0
ip address xx.xx.xx.xx 255.255.255.248
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
name-server 216.221.96.37
name-server 8.8.8.8
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended deny icmp interface outside interface inside
access-list outside_access_in extended permit ip 192.168.15.192 255.255.255.192 any
access-list Remote_splitTunnelAcl standard permit internal-network 255.255.255.0
access-list inside_nat0_outbound extended permit ip internal-network 255.255.255.0 192.168.15.192 255.255.255.192
access-list inside_access_in remark Block Internet Traffic
access-list inside_access_in extended permit ip 192.168.15.192 255.255.255.192 any
access-list inside_access_in remark Block Internet Traffic
access-list inside_access_in extended permit ip interface inside interface inside
access-list inside_access_in extended permit ip any 192.168.15.192 255.255.255.192
access-list inside_access_in remark Block Internet Traffic
access-list inside_nat0_outbound_1 extended permit ip 192.168.15.192 255.255.255.192 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_IP_Pool 192.168.15.200-192.168.15.250 mask 255.255.255.0
ipv6 access-list inside_access_ipv6_in permit ip interface inside interface inside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any echo-reply outside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 0 access-list inside_nat0_outbound_1 outside
nat (inside) 1 192.168.15.192 255.255.255.192
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group inside_access_ipv6_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 xx.xx.xx.xx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
http internal-network 255.255.255.0 inside
http yy.yy.yy.yy 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt connection timewait
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd address 192.168.15.200-192.168.15.250 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 192.168.15.101 source inside
ntp server 192.168.15.100 source inside prefer
webvpn
group-policy Remote internal
group-policy Remote attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Remote_splitTunnelAcl
username StockUser password t6a0Nv8HUfWtUdKz encrypted privilege 0
username StockUser attributes
vpn-group-policy Remote
tunnel-group Remote type remote-access
tunnel-group Remote general-attributes
address-pool VPN_IP_Pool
default-group-policy Remote
tunnel-group Remote ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f4271785b86e45dd3a17bab8f60cd2f3Hi Graham,
My first question is do you have a site to site VPN or Remote access client VPN.
After checking your configuration i see that you do not have any Site to SIte VPN configuration so i am assuming that you ara facing issue with the VPN client.
And if i understood correctly you are able to connect the VPN client but you not able to access the internal resources properly.
I would recommend you to tey and make teh following changes.
Remove the following configuration first:
nat (inside) 0 access-list inside_nat0_outbound_1 outside
nat (inside) 1 192.168.15.192 255.255.255.192
You do not need the 1st one and i do not understand the reason of the second one
Second one is your pool IP subnet (192.168.15.200-192.168.15.250) and i am not sure why you have added this NAT.
If possible change your Pool subnet all together because we do not recommend to use th POOL ip which is simlar to your local LAN.
Try the above changes and let me know in case if you have any issue.
Thanks
Jeet Kumar -
Asa 5505 transparent firewall issue
hi i am having uc560 with voice and data vlan and i am having 3560 layer3 switch and my network is working fine the dhcp for voice and data both are running in uc560.
now i add asa 5505 between uc560 and switch in transparent mode means from uc560 to asa 5505 outside interface and from asa inside interface to switch,
i conigured vlan1 -- inside and vlan 2 as outside in asa 5505
in my uc 560 data is vlan 1 and my voice is vlan 100.
when i connect my network with transparent mode firewall no dhcp amd no phones are working . but if i remove asa and i connect with uc560 to switch everything is fine.
is there anyway to work multiple voice and data vlan in asa 5505 transparent mode.hi rojas,
here is my problem,
my internet and voice all connected in the uc 560 so wat i am doing i am connecting firewall outside to uc 560 trunk port and the from inside to my switch.
when i connec to my switch it is giving message inconsistant vlan and it is port is blocked. and my phones are not working.
my data vlan1 is 192.168.123.x
and my voice vlan100 is 10.1.1.x
and the firewall ip 192.168.123.3 -
Asa 5505, the outside cant access to a server in the inside
hi, i have an Asa 5505, a pc in the outside with the ip 10.1.1.6 cant access to a server in the inside 192.168.1.4, pls help...
this is my conf:
ASA Version 8.0(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 0
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 10.1.1.2 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa804-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list 100 extended permit tcp any host 10.1.1.3 eq www
pager lines 24
logging enable
logging asdm debugging
mtu inside 1500
<--- More --->
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-613.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 10.1.1.3 192.168.1.4 netmask 255.255.255.255
access-group 100 in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
<--- More --->
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.254 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
<--- More --->
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:14e7b74fabc386613ae646b915f60e9e
: end
ciscoasa#Andres
The security level for your inside interface should be 100 ie.
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
After changing that can you
1) ping the outside interface of the ASA from the pc or ping the PC from the ASA
2) I'm assuming you are trying to connect to 10.1.1.3 when you attempt the connection ?
Jon -
Internet Connection Became Slow after Introduction of Cisco ASA 5505 to the Network
I configured a Cisco ASA 5505 (Version Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
in transparent firewall mode and inserted after Cisco 1700 router. However, the internet connection became very slow and users are compaining that they cannot load any pages.
My setup looks like:
Internet --> Cisco 1700 --> Cisco ASA 5505 --> LAN
The license information is:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
My running-config looks like:
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Vlan1
nameif inside
security-level 100
no shut
interface Vlan2
nameif outside
security-level 0
no shut
interface Ethernet0/0
switchport access vlan 2
no shut
interface Ethernet0/1
no shut
interface Ethernet0/2
no shut
interface Ethernet0/3
no shut
interface Ethernet0/4
no shut
interface Ethernet0/5
no shut
interface Ethernet0/6
no shut
interface Ethernet0/7
no shut
passwd 2KFQnbNIdI.2KYOU encrypted
regex urllist1 ".*\.([Ee][Xx][Ee]|[Cc][Oo][Mm]|[Bb][Aa][Tt]) HTTP/1.[01]"
regex urllist2 ".*\.([Pp][Ii][Ff]|[Vv][Bb][Ss]|[Ww][Ss][Hh]) HTTP/1.[01]"
regex urllist3 ".*\.([Dd][Oo][Cc]|[Xx][Ll][Ss]|[Pp][Pp][Tt]) HTTP/1.[01]"
regex urllist4 ".*\.([Zz][Ii][Pp]|[Tt][Aa][Rr]|[Tt][Gg][Zz]) HTTP/1.[01]"
regex domainlist1 "\.facebook\.com"
regex domainlist2 "\.diretube\.com"
regex domainlist3 "\.youtube\.com"
regex domainlist4 "\.vimeo\.com"
regex applicationheader "application/.*"
regex contenttype "Content-Type"
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_in extended permit ip any any
access-list inside_mpc extended permit tcp any any eq www
access-list inside_mpc extended permit tcp any any eq 8080
pager lines 24
mtu outside 1500
mtu inside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domainlist1
match regex domainlist2
match regex domainlist3
match regex domainlist4
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map type regex match-any URLBlockList
match regex urllist1
match regex urllist2
match regex urllist3
match regex urllist4
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all AppHeaderClass
match response header regex contenttype regex applicationheader
class-map httptraffic
match access-list inside_mpc
class-map type inspect http match-all BlockURLsClass
match request uri regex class URLBlockList
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action drop-connection
class AppHeaderClass
drop-connection log
match request method connect
drop-connection log
class BlockDomainsClass
reset log
class BlockURLsClass
reset log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
policy-map inside-policy
class httptraffic
inspect http http_inspection_policy
service-policy global_policy global
service-policy inside-policy interface inside
prompt hostname context
Cryptochecksum:8ab1a53df6ae3c202aee236d6080edfd
: end
Could the slow internet connection be due to license limitations? Or is there something wrong with my configuration?
Please see the configuration and help.
ThanksI have re-configured the ASA 5505 yesterday and so far it's working fine. I am not sure if the problem will re-appear later on. Anyways here is my sh tech-support
ciscoasa# sh tech-support
Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
Compiled on Wed 15-Aug-07 16:08 by builders
System image file is "disk0:/asa723-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 14 hours 16 mins
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0 : address is 001f.9ee8.ffa2, irq 11
1: Ext: Ethernet0/0 : address is 001f.9ee8.ff9a, irq 255
2: Ext: Ethernet0/1 : address is 001f.9ee8.ff9b, irq 255
3: Ext: Ethernet0/2 : address is 001f.9ee8.ff9c, irq 255
4: Ext: Ethernet0/3 : address is 001f.9ee8.ff9d, irq 255
5: Ext: Ethernet0/4 : address is 001f.9ee8.ff9e, irq 255
6: Ext: Ethernet0/5 : address is 001f.9ee8.ff9f, irq 255
<--- More --->
7: Ext: Ethernet0/6 : address is 001f.9ee8.ffa0, irq 255
8: Ext: Ethernet0/7 : address is 001f.9ee8.ffa1, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
Serial Number: JMX1211Z2N4
Running Activation Key: 0xaf0ed046 0xbcf18ebf 0x80b38508 0xba785cc0 0x05250493
Configuration register is 0x1
Configuration has not been modified since last system restart.
<--- More --->
------------------ show clock ------------------
18:32:58.254 UTC Tue Nov 26 2013
------------------ show memory ------------------
Free memory: 199837144 bytes (74%)
Used memory: 68598312 bytes (26%)
Total memory: 268435456 bytes (100%)
------------------ show conn count ------------------
1041 in use, 2469 most used
------------------ show xlate count ------------------
0 in use, 0 most used
------------------ show blocks ------------------
SIZE MAX LOW CNT
0 100 68 100
<--- More --->
4 300 299 299
80 100 92 100
256 100 94 100
1550 6174 6166 6174
2048 1124 551 612
------------------ show blocks queue history detail ------------------
History buffer memory usage: 2136 bytes (default)
------------------ show interface ------------------
Interface Internal-Data0/0 "", is up, line protocol is up
Hardware is y88acs06, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 001f.9ee8.ffa2, MTU not set
IP address unassigned
18491855 packets input, 11769262614 bytes, 0 no buffer
Received 213772 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops, 0 demux drops
18185861 packets output, 11626494317 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 late collisions, 0 deferred
<--- More --->
0 input reset drops, 0 output reset drops
input queue (curr/max packets): hardware (0/0) software (0/0)
output queue (curr/max packets): hardware (0/55) software (0/0)
Control Point Interface States:
Interface number is unassigned
Interface Internal-Data0/1 "", is administratively down, line protocol is up
Hardware is 88E6095, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 0000.0003.0002, MTU not set
IP address unassigned
18184216 packets input, 11625360131 bytes, 0 no buffer
Received 206655 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 switch ingress policy drops
18490057 packets output, 11768078777 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Loopback0 "_internal_loopback", is up, line protocol is up
Hardware is VirtualMAC address 0000.0000.0000, MTU 1500
IP address 127.1.0.1, subnet mask 255.255.0.0
<--- More --->
Traffic Statistics for "_internal_loopback":
1 packets input, 28 bytes
1 packets output, 28 bytes
1 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 28
Interface config status is active
Interface state is active
Interface Vlan1 "inside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa2, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "inside":
7742275 packets input, 903584114 bytes
10645034 packets output, 10347291114 bytes
184883 packets dropped
1 minute input rate 320 pkts/sec, 35404 bytes/sec
1 minute output rate 325 pkts/sec, 313317 bytes/sec
<--- More --->
1 minute drop rate, 17 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
Control Point Interface States:
Interface number is 1
Interface config status is active
Interface state is active
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa3, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "outside":
10750090 packets input, 10432619059 bytes
7541331 packets output, 870613684 bytes
109911 packets dropped
1 minute input rate 328 pkts/sec, 313770 bytes/sec
1 minute output rate 301 pkts/sec, 32459 bytes/sec
1 minute drop rate, 2 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
Control Point Interface States:
Interface number is 2
<--- More --->
Interface config status is active
Interface state is active
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001f.9ee8.ff9a, MTU not set
IP address unassigned
10749794 packets input, 10630700889 bytes, 0 no buffer
Received 2506 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
3 switch ingress policy drops
7541070 packets output, 1028190148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/1 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
<--- More --->
Available but not configured via nameif
MAC address 001f.9ee8.ff9b, MTU not set
IP address unassigned
7741977 packets input, 1064586806 bytes, 0 no buffer
Received 211282 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
10644663 packets output, 10543362751 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/2 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9c, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
<--- More --->
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/3 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9d, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/4 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9e, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
<--- More --->
Interface number is unassigned
Interface Ethernet0/5 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9f, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/6 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
<--- More --->
MAC address 001f.9ee8.ffa0, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/7 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ffa1, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
------------------ show cpu usage ------------------
CPU utilization for 5 seconds = 12%; 1 minute: 11%; 5 minutes: 11%
------------------ show cpu hogging process ------------------
Process: Dispatch Unit, NUMHOG: 1, MAXHOG: 133, LASTHOG: 140
LASTHOG At: 04:45:59 UTC Nov 26 2013
PC: 8be0f7
Traceback: 8bed19 8bf553 302b87 3030a5 2fad69 7674bf 75ca16
c6251d c62a4c c62f6c 75c653 767820 797f64 769c85
<--- More --->
------------------ show process ------------------
PC SP STATE Runtime SBASE Stack Process
Mwe 00c9bb24 01bb8700 013e3250 0 01733fc8 15616/16384 emweb/cifs
Lwe 001072ac 0176f9c4 013e32d0 0 0176d9f0 8132/8192 block_diag
Mrd 00223a67 01783d5c 013e33b0 314854 0177be18 25752/32768 Dispatch Unit
Msi 00f82847 01b07b84 013e3250 229 01b05bc0 7984/8192 y88acs06 OneSec Thread
Mwe 0011b1a5 01b09cfc 013e3250 0 01b07d88 7864/8192 Reload Control Thread
Mwe 00120606 01b1260c 013e5258 0 01b10988 7256/8192 aaa
Mwe 001486aa 01b19404 013e5ae8 0 01b15450 16020/16384 CMGR Server Process
Mwe 0014c3c5 01b1b4d4 013e3250 0 01b19570 7968/8192 CMGR Timer Process
Lwe 002227a1 01b239b4 013ee360 0 01b219f0 7524/8192 dbgtrace
Mwe 004e1ba5 01b29c34 013e3250 157 01b27d50 6436/8192 eswilp_svi_init
Mwe 01064b1d 01b4a7f4 013e3250 0 01b48890 7848/8192 Chunk Manager
Msi 008b61b6 01b52d54 013e3250 230 01b50da0 7856/8192 PIX Garbage Collector
Lsi 00ecb6ac 01b54e94 013e3250 12 01b52ec0 7552/8192 route_process
Mwe 008a5ddc 01b5dc04 0133b430 0 01b5bc40 8116/8192 IP Address Assign
Mwe 00acb779 01b60604 01346e10 0 01b5e640 8116/8192 QoS Support Module
Mwe 0091eba9 01b6275c 0133c530 0 01b60798 8116/8192 Client Update Task
Lwe 01083c8e 01b656d4 013e3250 123088 01b63770 7840/8192 Checkheaps
Mwe 00acfd7d 01b6b824 013e3250 623 01b69ad0 3476/8192 Quack process
Mwe 00b2a260 01b6dad4 013e3250 22 01b6bbf0 7364/8192 Session Manager
Mwe 00c55efd 01b78564 031d0478 4 01b74a50 14768/16384 uauth
<--- More --->
Mwe 00be3c9e 01b7aaec 0135c010 0 01b78b28 7524/8192 Uauth_Proxy
Mwe 00c52759 01b80e0c 01361770 0 01b7ee88 7712/8192 SMTP
Mwe 00c3f7b9 01b82eec 01361710 0 01b80fa8 7412/8192 Logger
Mwe 00c3fd26 01b8502c 013e3250 0 01b830c8 7492/8192 Thread Logger
Mwe 00f62272 01b9596c 013ac520 0 01b939c8 7188/8192 vpnlb_thread
Msi 00b4097c 01c598c4 013e3250 190 01c578f0 8000/8192 emweb/cifs_timer
Msi 005bd338 017a909c 013e3250 25855 017a7108 7412/8192 arp_timer
Mwe 005c76bc 01b486e4 013fba50 20643 01b46770 7348/8192 arp_forward_thread
Mwe 00c5a919 023fa5fc 013619e0 0 023f8648 7968/8192 tcp_fast
Mwe 00c5a6e5 023fc624 013619e0 0 023fa670 7968/8192 tcp_slow
Mwe 00c754d1 0240d42c 013628a0 0 0240b478 8100/8192 udp_timer
Mwe 0019cb17 01b404a4 013e3250 0 01b3e530 7984/8192 CTCP Timer process
Mwe 00efe8b3 0308c15c 013e3250 0 0308a208 7952/8192 L2TP data daemon
Mwe 00efef23 0308e194 013e3250 0 0308c230 7968/8192 L2TP mgmt daemon
Mwe 00eea02b 030c62ac 013a5c10 43 030c2338 16244/16384 ppp_timer_thread
Msi 00f62d57 030c82f4 013e3250 264 030c6360 7924/8192 vpnlb_timer_thread
Mwe 001b96e6 01b7cbbc 01b1e9c8 1 01b7ac48 7728/8192 IPsec message handler
Msi 001c9bac 01b8d4dc 013e3250 2917 01b8b548 7648/8192 CTM message handler
Mwe 00af93b8 031465b4 013e3250 0 03144640 7984/8192 ICMP event handler
Mwe 00831003 0314a724 013e3250 387 031467b0 16100/16384 IP Background
Mwe 0021b267 031a83c4 013123c0 31 03188450 123488/131072 tmatch compile thread
Mwe 009f2405 03290044 013e3250 0 0328c0c0 16072/16384 Crypto PKI RECV
Mwe 009f305a 03294144 013e3250 0 032901e0 16040/16384 Crypto CA
Mwe 0064d4fd 01b3e24c 013e3250 8 01b3c2f8 7508/8192 ESW_MRVL switch interrupt service
<--- More --->
Msi 00646f5c 032c134c 013e3250 3059378 032bf448 7184/8192 esw_stats
Lsi 008cbb80 032dc704 013e3250 3 032da730 7908/8192 uauth_urlb clean
Lwe 008afee7 034a0914 013e3250 197 0349e9b0 6636/8192 pm_timer_thread
Mwe 0052f0bf 034a35ac 013e3250 0 034a1648 7968/8192 IKE Timekeeper
Mwe 00520f6b 034a8adc 0132e2b0 0 034a4e38 15448/16384 IKE Daemon
Mwe 00bf5c78 034ac7ac 01360680 0 034aa7f8 8100/8192 RADIUS Proxy Event Daemon
Mwe 00bc32de 034ae79c 034dcbe0 0 034ac918 7208/8192 RADIUS Proxy Listener
Mwe 00bf5e0f 034b099c 013e3250 0 034aea38 7968/8192 RADIUS Proxy Time Keeper
Mwe 005aac4c 034b3154 013fb980 0 034b1250 7492/8192 Integrity FW Task
M* 008550a5 0009fefc 013e33b0 3183 034e3b20 24896/32768 ci/console
Msi 008eb694 034ed9d4 013e3250 2370 034ebc40 6176/8192 update_cpu_usage
Msi 008e6415 034f7dac 013e3250 1096 034f5eb8 6124/8192 NIC status poll
Mwe 005b63e6 03517d1c 013fbd10 1963 03515d78 7636/8192 IP Thread
Mwe 005becbe 03519e4c 013fbcb0 3 03517e98 7384/8192 ARP Thread
Mwe 004c2b36 0351befc 013fbae0 0 03519fe8 7864/8192 icmp_thread
Mwe 00c7722e 0351e06c 013e3250 0 0351c108 7848/8192 udp_thread
Mwe 00c5d126 0352008c 013fbd00 0 0351e228 7688/8192 tcp_thread
Mwe 00bc32de 03a6982c 03a5ee18 0 03a679b8 7512/8192 EAPoUDP-sock
Mwe 00266c15 03a6b614 013e3250 0 03a699e0 7032/8192 EAPoUDP
Mwe 005a6728 01b27b94 013e3250 0 01b25c30 7968/8192 Integrity Fw Timer Thread
- - - - 47686621 - - scheduler
- - - - 51253819 - - total elapsed
------------------ show failover ------------------
<--- More --->
ERROR: Command requires failover license
------------------ show traffic ------------------
inside:
received (in 51429.740 secs):
7749585 packets905087345 bytes
67 pkts/sec17013 bytes/sec
transmitted (in 51429.740 secs):
10653162 packets10355908020 bytes
40 pkts/sec201026 bytes/sec
1 minute input rate 412 pkts/sec, 51803 bytes/sec
1 minute output rate 475 pkts/sec, 522952 bytes/sec
1 minute drop rate, 24 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
outside:
received (in 51430.240 secs):
10758403 packets10441440193 bytes
42 pkts/sec203021 bytes/sec
transmitted (in 51430.240 secs):
7548339 packets872053854 bytes
<--- More --->
63 pkts/sec16037 bytes/sec
1 minute input rate 479 pkts/sec, 523680 bytes/sec
1 minute output rate 387 pkts/sec, 46796 bytes/sec
1 minute drop rate, 3 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
_internal_loopback:
received (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Aggregated Traffic on Physical Interface
<--- More --->
Ethernet0/0:
received (in 51431.740 secs):
10758462 packets10640075825 bytes
42 pkts/sec206042 bytes/sec
transmitted (in 51431.740 secs):
7548383 packets1029818127 bytes
63 pkts/sec20023 bytes/sec
1 minute input rate 485 pkts/sec, 537048 bytes/sec
1 minute output rate 395 pkts/sec, 54546 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 485 pkts/sec, 511723 bytes/sec
5 minute output rate 387 pkts/sec, 65495 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/1:
received (in 51433.570 secs):
7749780 packets1066328930 bytes
67 pkts/sec20064 bytes/sec
transmitted (in 51433.570 secs):
10653359 packets10552787020 bytes
40 pkts/sec205006 bytes/sec
1 minute input rate 419 pkts/sec, 59621 bytes/sec
1 minute output rate 480 pkts/sec, 533950 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 399 pkts/sec, 67618 bytes/sec
<--- More --->
5 minute output rate 482 pkts/sec, 511073 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/2:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/3:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
<--- More --->
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/4:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/5:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
<--- More --->
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/6:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/7:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
<--- More --->
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/0:
received (in 51435.510 secs):
18513901 packets11784250044 bytes
25 pkts/sec229023 bytes/sec
transmitted (in 51435.510 secs):
18207269 packets11641332179 bytes
19 pkts/sec226078 bytes/sec
1 minute input rate 891 pkts/sec, 595715 bytes/sec
1 minute output rate 863 pkts/sec, 588935 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 885 pkts/sec, 584035 bytes/sec
5 minute output rate 870 pkts/sec, 580393 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/1:
received (in 51436.010 secs):
18207323 packets11641364184 bytes
<--- More --->
19 pkts/sec226076 bytes/sec
transmitted (in 51436.010 secs):
18513954 packets11784281987 bytes
25 pkts/sec229022 bytes/sec
1 minute input rate 855 pkts/sec, 575808 bytes/sec
1 minute output rate 884 pkts/sec, 582339 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 869 pkts/sec, 578350 bytes/sec
5 minute output rate 883 pkts/sec, 581924 bytes/sec
5 minute drop rate, 0 pkts/sec
------------------ show perfmon ------------------
PERFMON STATS: Current Average
Xlates 0/s 0/s
Connections 17/s 6/s
TCP Conns 8/s 2/s
UDP Conns 7/s 2/s
URL Access 0/s 0/s
URL Server Req 0/s 0/s
TCP Fixup 0/s 0/s
TCP Intercept 0/s 0/s
HTTP Fixup 0/s 0/s
<--- More --->
FTP Fixup 0/s 0/s
AAA Authen 0/s 0/s
AAA Author 0/s 0/s
AAA Account 0/s 0/s
------------------ show counters ------------------
Protocol Counter Value Context
IP IN_PKTS 168960 Summary
IP OUT_PKTS 169304 Summary
IP TO_ARP 61 Summary
------------------ show history ------------------
------------------ show firewall ------------------
Firewall mode: Transparent
------------------ show running-config ------------------
<--- More --->
: Saved
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
enable password
names
interface Vlan1
nameif inside
security-level 100
interface Vlan2
nameif outside
security-level 0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
<--- More --->
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd
regex domain1 ".facebook\.com"
regex domain2 ".fb\.com"
regex domain3 ".youtube\.com"
ftp mode passive
access-list ACL_IN extended permit ip any any
pager lines 24
mtu inside 1500
mtu outside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
<--- More --->
arp timeout 14400
access-group ACL_IN in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domain1
match regex domain2
match regex domain3
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
<--- More --->
message-length maximum 512
match domain-name regex class DomainBlockList
drop-connection log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:bb5115ea1d14ee42e7961ef0c9aaed86
: end
<--- More --->
------------------ show startup-config errors ------------------
INFO: No configuration errors
------------------ console logs ------------------
Message #1 : Message #2 : Message #3 : Message #4 : Message #5 : Message #6 : Message #7 : Message #8 : Message #9 : Message #10 : Message #11 : Message #12 : Message #13 : Message #14 :
Total SSMs found: 0
Message #15 :
Total NICs found: 10
Message #16 : 88E6095 rev 2 Gigabit Ethernet @ index 09Message #17 : MAC: 0000.0003.0002
Message #18 : 88E6095 rev 2 Ethernet @ index 08Message #19 : MAC: 001f.9ee8.ffa1
Message #20 : 88E6095 rev 2 Ethernet @ index 07Message #21 : MAC: 001f.9ee8.ffa0
Message #22 : 88E6095 rev 2 Ethernet @ index 06Message #23 : MAC: 001f.9ee8.ff9f
Message #24 : 88E6095 rev 2 Ethernet @ index 05Message #25 : MAC: 001f.9ee8.ff9e
Message #26 : 88E6095 rev 2 Ethernet @ index 04Message #27 : MAC: 001f.9ee8.ff9d
Message #28 : 88E6095 rev 2 Ethernet @ index 03Message #29 : MAC: 001f.9ee8.ff9c
Message #30 : 88E6095 rev 2 Ethernet @ index 02Message #31 : MAC: 001f.9ee8.ff9b
Message #32 : 88E6095 rev 2 Ethernet @ index 01Message #33 : MAC: 001f.9ee8.ff9a
Message #34 : y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 001f.9ee8.ffa2
Message #35 :
Licensed features for this platform:
Message #36 : Maximum Physical Interfaces : 8
<--- More --->
Message #37 : VLANs : 3, DMZ Restricted
Message #38 : Inside Hosts : Unlimited
Message #39 : Failover : Disabled
Message #40 : VPN-DES : Enabled
Message #41 : VPN-3DES-AES : Enabled
Message #42 : VPN Peers : 10
Message #43 : WebVPN Peers : 2
Message #44 : Dual ISPs : Disabled
Message #45 : VLAN Trunk Ports : 0
Message #46 :
This platform has a Base license.
Message #47 :
Message #48 : Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Message #49 : Boot microcode : CNlite-MC-Boot-Cisco-1.2
Message #50 : SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
Message #51 : IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
Message #52 : --------------------------------------------------------------------------
Message #53 : . .
Message #54 : | |
Message #55 : ||| |||
Message #56 : .|| ||. .|| ||.
Message #57 : .:||| | |||:..:||| | |||:.
Message #58 : C i s c o S y s t e m s
Message #59 : --------------------------------------------------------------------------
<--- More --->
Message #60 :
Cisco Adaptive Security Appliance Software Version 7.2(3)
Message #61 :
Message #62 : ****************************** Warning *******************************
Message #63 : This product contains cryptographic features and is
Message #64 : subject to United States and local country laws
Message #65 : governing, import, export, transfer, and use.
Message #66 : Delivery of Cisco cryptographic products does not
Message #67 : imply third-party authority to import, export,
Message #68 : distribute, or use encryption. Importers, exporters,
Message #69 : distributors and users are responsible for compliance
Message #70 : with U.S. and local country laws. By using this
Message #71 : product you agree to comply with applicable laws and
Message #72 : regulations. If you are unable to comply with U.S.
Message #73 : and local laws, return the enclosed items immediately.
Message #74 :
Message #75 : A summary of U.S. laws governing Cisco cryptographic
Message #76 : products may be found at:
Message #77 : http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
Message #78 :
Message #79 : If you require further assistance please contact us by
Message #80 : sending email to [email protected].
Message #81 : ******************************* Warning *******************************
Message #82 :
<--- More --->
Message #83 : Copyright (c) 1996-2007 by Cisco Systems, Inc.
Message #84 : Restricted Rights Legend
Message #85 : Use, duplication, or disclosure by the Government is
Message #86 : subject to restrictions as set forth in subparagraph
Message #87 : (c) of the Commercial Computer Software - Restricted
Message #88 : Rights clause at FAR sec. 52.227-19 and subparagraph
Message #89 : (c) (1) (ii) of the Rights in Technical Data and Computer
Message #90 : Software clause at DFARS sec. 252.227-7013.
Message #91 : Cisco Systems, Inc.
Message #92 : 170 West Tasman Drive
Message #93 : San Jose, California 95134-1706
ciscoasa# -
Cisco ASA 5505 doesn't forware incoming connection to LAN
Hello everybody.
I just got a Cisco asa 5505 with the next OS and ASDM info
ASA 5505 OS 8.4(3) ASDM 6.47
I configured and enter all rules to allow incoming traffic to LAN but it's not working also, I have one host inside that is configured in a second IP and create the rule to allow traffic to it but it doesn't work too.
Problem 1
I have VNC running in port 5900 tcp and I want to connect from Internet using port 6001 and this has to forware the connection to the real VNC port. In the configuration I have a few host with the same configuration but I use different outside port to get it.
Problem 2.
I have a second IP with services: SMTP, HTTP, HTTPS and port 444 all TCP forwarding to a server in the LAN.
Facts:
SMTP.
Every time that I do telnet to the second IP looking for the SMTP port, the firewall doesn't let the incoming connection goes through and the LOGGING screen doesn't how that connection.
PORT 6001 (outside)
this port is configured to work with the IP in the outside internface and it was to send the incoming connection to a host inside to the real port 5900.
Can any one check my configuration if I'm missing anything? for sure I'm but I didn't find it. Bellow is the configuration, I masked the Public IPs just left the last number in the IP, also I left the LAN network to see better the configuration.
I will appreciate any help.
Thanks a lot..
CONFIGURATION.
: Saved
ASA Version 8.4(3)
hostname saturn1
domain-name mydominio.com
enable password SOMEPASS encrypted
passwd SOMEPASS encrypted
names
name 192.168.250.11 CAPITOLA-LAN
name 192.168.250.15 OBIi110-LAN
name 192.168.250.21 DRP1260-LAN
name 192.168.250.22 HPOJ8500-LAN
name 192.168.250.30 AP-W77-NG-LAN
name 192.168.250.97 AJ-DTOP-PC-LAN
name 192.168.250.96 SWEETHEART-PC-LAN
name 192.168.250.94 KIDS-PC-LAN
name XX.YY.ZZ.250 EXTERNALIP
name XX.YY.ZZ.251 EXTERNALIP2
name XX.YY.ZZ.1 GTWAY
dns-guard
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.250.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address EXTERNALIP 255.255.255.0
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name mydominio.com
object network CAPITOLA-LAN
host 192.168.250.11
object network EXTERNALIP
host XX.YY.ZZ.250
description Created during name migration
object network CAPITOLA-PUBLIC
host XX.YY.ZZ.251
object network capitola-int
host 192.168.250.11
object network capitola-int-vnc
host 192.168.250.11
object network aj-dtop-int-vnc
host 192.168.250.97
object network sweetheart-int-vnc
host 192.168.250.96
object network kids-int-vnc
host 192.168.250.94
object network VPNNetwork
subnet 10.10.20.0 255.255.255.0
object network InsideNetwork
subnet 192.168.250.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network capitola-int-smtp
host 192.168.250.11
object-group service capitola-int-smtp-service tcp
port-object eq smtp
object-group service capitola-int-services tcp
port-object eq smtp
port-object eq https
port-object eq www
port-object eq 444
object-group service capitola-int-vnc-service tcp
port-object eq 6001
object-group service aj-dtop-int-vnc-service tcp
port-object eq 6002
object-group service sweetheart-int-vnc-service tcp
port-object eq 6003
object-group service kids-int-vnc-service tcp
port-object eq 6004
access-list incoming extended permit icmp any any
access-list incoming extended permit tcp any object capitola-int object-group capitola-int-services
access-list incoming extended permit tcp any object capitola-int-vnc object-group capitola-int-vnc-service
access-list incoming extended permit tcp any object aj-dtop-int-vnc object-group aj-dtop-int-vnc-service
access-list incoming extended permit tcp any object sweetheart-int-vnc object-group sweetheart-int-vnc-service
access-list incoming extended permit tcp any object kids-int-vnc object-group kids-int-vnc-service
access-list incoming extended permit tcp any object capitola-int-smtp object-group capitola-int-smtp-service
access-list split-tunnel standard permit 192.168.250.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any object VPNNetwork
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 10.10.20.1-10.10.20.50 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static any any destination static VPNNetwork VPNNetwork no-proxy-arp
object network capitola-int
nat (any,any) static XX.YY.ZZ.251
object network capitola-int-vnc
nat (inside,outside) static interface service tcp 5900 6001
object network aj-dtop-int-vnc
nat (inside,outside) static interface service tcp 5900 6002
object network sweetheart-int-vnc
nat (inside,outside) static interface service tcp 5900 6003
object network kids-int-vnc
nat (inside,outside) static interface service tcp 5900 6004
object network obj_any
nat (inside,outside) dynamic interface
object network capitola-int-smtp
nat (any,outside) static interface service tcp smtp smtp
access-group incoming in interface outside
route outside 0.0.0.0 0.0.0.0 GTWAY 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http server idle-timeout 2
http server session-timeout 1
http 192.168.1.0 255.255.255.0 inside
http CAPITOLA-LAN 255.255.255.255 inside
http AJ-DTOP-PC-LAN 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh CAPITOLA-LAN 255.255.255.255 inside
ssh AJ-DTOP-PC-LAN 255.255.255.255 inside
ssh timeout 15
console timeout 0
vpn-addr-assign local reuse-delay 2
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password SOMEPASS encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:036b82d3eb5cffc1c65a3b381246d043
: end
asdm image disk0:/asdm-647.bin
no asdm history enableJose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface. Try to be more restrictive than an '...ip any any' rule for outside_in connections. For instance, this is what I have for incoming VOIP (access list and nat rules):
access list rule:
access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
nat rule:
nat (inside,outside) source static server interface service voip-range voip-range
- 'server' is a network object *
- 'voip-range' is a service group range
I'd assume you can do something similar here in combination with my earlier comment:
access-list incoming extended permit tcp any any eq 5900
Can you explain your forwarding methodology a little more? I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to. Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ? -
ASA 5505 - 2 Internet Connections, Problems with the Default Route
Hey there,
i have a Problem at a Customer Site at the moment. The customer uses an ASA 5505 with two internet connections attached to it. On the first connection (which is the only one in use at the moment) he has some Static-PAT's from Outside to Inside where he translates different services to the internal servers. He also has a site-2-site VPN terminating there and AnyConnect.
He now wants to switch the Internet Traffic from Inside to the new Internet Connection. Therefore changing the default route to that new ISPs Gateway. The problem now is, that no traffic recieved on the old "outside" Interface is transmitted back out of that old "outside" Interface. And this happens although the "same-security permit intra-interface" command is set.
Can you tell me what's wrong here? For every Static-PAT from outside to inside there is also a dynamic PAT from inside to outside. But the ASA seems to ignore this. I have not looked into the Logs yet, was too busy finding the problem because i had no real time window to test on the productive ASA.
Can it be achieved in any way? Having a default route on the ASA which leads any traffic to the second internet connection while still having connections on the first internet connection where no explicit route can be set? Because connections arrive from random IPs?
Many thanks for your help in advance!
SteffenPhillip, indeed , I have as well read may comments,it all depends on your environment as they all differ from one another, you best bet is to have a good solid plan for upgrade and fall back. You do have a justification to upgrade for features needed, so I would suggest the following:
1- Do a search again in forum for ASA code upgrades and look at comments from users that have gone through this process and note their impact in fuctionality if any. I believe this is good resource to collect information .
2- Very important , look into release notes for a particular version. For example version 8.0, look into open CAVEATS usually at the end of the link page, reading the open bugs gives you clues what has not yet been resolved for that particular code and if in fact could impact you in your environment, it is possible that a particular bug does not realy apply to your environment becuase you have yet not implemented that particualr configuration. Usually we all try to aim towards a GD (General Deployment) code which is what we all understand is most stable but not necesarily means you have to be stack in that code waiting for another GD release, in my personal experience I have upgraded our firewall from 7.2 to 8.0(3) long ago and had no issues, and recently upgraded to 8.0(4)when it was first release in August this year.
Release notes
http://www.cisco.com/en/US/products/ps6120/prod_release_notes_list.html
3- AS a good practice precaution -
a-Backup firewall configs in clear text as well as via tftp code.
b-Backup running code and ASDM version code currently running in firewall.
c- Save the output of " show version " to have as reference for all the feature licenses you currently have running as asll as activation keys - good info to have to compare with after upgrade.
d- Ensure that the code you will be using to upgrade also uses correct ASDM version code.
I think with thorough assesment and preparation you can indeed minimize impact.
Rgds
Jorge
Maybe you are looking for
-
How to put a single stack item to an album?
Maybe a silly question, but I can't find out how to put a single item from a stack into an album. When I drag a stacked item to an album, the entire stack appears in the album. This is not what I want, I want to get the single item in the album. I kn
-
Concatenating to a variable more than once?
Is it possible to concat to the same variable more than once? For some reason I am thinking not. I have the following: declare v_sql VARCHAR2(2000); v_sql := 'Select blah balh Where myfield in ('; if v_show1 = 1 then v_sql := v_sql || '1,' end if; if
-
OS X Yosemite 10.10.2, Macbook Air, Finder batch file rename function. I have multiple files I want to rename, that have a date in their name in the mm/dd/yy format. The slashes seem to freak out the batch rename function and it won't work. I took o
-
While loop never stops after reading the result
I 'amattaching the program with thismessage in which while loop never stops, going on continuing until I stops it manualy using the off button What i have to do to get it off automatically afetr execution and reading the query and getting the result
-
Searching for the methods applied to each type of object....
Hi everybody... I want to find all the methods applied to each type of object in Swing/AWT java application..... for example in a text filed , there is jTextField1.setText('test')... in a combo box , there is jComboBox1.addItem("4").... Where can I f