Connection to airport express dies out from iTunes after 1-3 hours

I have iTunes running in Windows XP. It is connected to zyxel WLAN AP through ethernet and Airport express is connected over wlan to this Zyxel. I have two problems where worse one is that after sometime 1-3 hours iTunes looses connection to airport express(remote speakers). Only way to return is to shut down power from AE. Then streaming can be started again. it seems that Internet connection is working all the time through zyxel, so this is not probably related to wlan itself
Other problem seems to be that Itunes can find AE only after reboot. I have opened firewall, so good ideas what is wrong in these two problems.

Yes, there's an exception for Bonjour in the firewall (Bonjour is allowed)
I've try to re-add the "APAgent" which control Airports and restart the firewall but it didn't worked...
The only solution I've found was to desactivate Windows firewall...
(Firewall of my ADSL box is activated).
Maybe I should try to repair iTunes Installation like WPLU...

Similar Messages

I am using an airport express to stream from iTunes to my stereo. My router is a net gear type G. Setting up is no problem for the first time. But, when I close iTunes then restart I have to reset (using the reset button)and reset up. Wanna do it one?

Using a. Airport express to stream from iTunes. My Router is a Netgear type G. The express sets up fine and works the first time. When I try to use it at a later date after closing then reopening iTunes I have to physically reset the express and then go through the process of finding it again. Is this normal?

I have a 3rd generation (802.11n capable, 2.4Ghz only) airport express, my problem is that I've tried using it to extend my network and that brick wall, no matter how close I get the express to the room, the signal and throughput in that room becomes abysmal.
As you might imagine, brick is a lot like cement, and it will not allow much of the wireless signal through.
Regarding your Express, there is no such thing as a 3rd Generation model....yet. You likely have a 1st Generation AirPort Express. Check and confirm the Model No on the side of the Express. A 1st Gen model is A1264.
Here's my problem, I don't think the express supports "extending" a network from a wired network jack.
The Express can "extend" wirelessly, or using an Ethernet connection. The configuration for this is very simple, but post back if you need it.
The jack just seems to be shut off
Have you temporarily turned off the wireless on a laptop and tried to connect it using an Ethernet cable to the wall jack as a "test"?
If you can get a good Internet connection this way, then you know the Ethernet cabling and jack are working correctly.
On the other hand, if you cannot get an Internet connection on the laptop during this "test", then this indicates that the Ethernet cable or jack is not functioning correctly and the wiring will need troubleshooting before you can proceed any further.
I need to create a whole new wireless network in this room for this configuration to work?
AirPort Setup will take care of this for you automatically during the configuration of the AirPort Express.
If I have an apple TV connecting to the express and an AppleTV connecting to the extreme, will they both be visible when connected wirelessly to either network?
Yes
Will I be able to connect to my network seemlessly?
Yes
Post back after you have confirmed that the Ethernet cable and Ethernet jack are functioning correctly in the temporary "test" mentioned above. Then, we will continue.

Can no longer connect to Airport Express with upgrade to iTunes 10.1

Since I upgraded to iTunes 10.1 I can no longer connect to my Airport Express (unknown error-15000). Another computer on my betwork running an older version of iTunes still works on the Airport Express.
Any ideas? I have tried to uninstall and reinstall airport express with no success.

Rather than disabling the firewall, try making sure you've got exceptions in it for BonJour. Although the following document is about a different error message, the instructions in there are worth trying. (At step 7, make sure there's an exception for BonJour as well.)
[iTunes for Windows: Bonjour alert due to firewall, security, or proxy software|http://support.apple.com/kb/TS3448]

Cannot select Airport Express as speaker from iTunes

I have installed iTunes 7.6.2.9 on a MS Windows Vista Home Premium, and I get the speaker selector in the lower right corner as I´m used to, since I have an Airport Express connected to my stereo. I can also click the name of the AE, but the selection stays at "This computer".
The settings in the AE does not give me a clue as to what is wrong. Can anyone here help? Thanks in advance.
Best regards,
David List

Found the problem myself: the parental control settings in MS Windows Vista, which I had turned on for the sake of logging activity on my non-privileged user account. I had set the settings for this account so that nothing was restricted - it was just the logging that was done. Nevertheless, this was what gave me the problem with external speaker, and also with iTunes Store generally dying on me - or at least responding sloooooooooowly.
Best regards,
David List

I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

Ok, if you are connecting the AirPort Express Base Station (AX) to the existing wireless network, then the DSL in the next room is most likely a combination DSL modem and wireless router. Thanks for clarifying that for me.
Although they may only be separated by a single wall, the building material used in that wall may be enough to prevent the AX from receving a "good" signal from the DSL router.
Since I don't know what computing equipment you have available, please check out this AirPort User Tip: AirPort - Optimal Base Station Placement to see if you can get some SNR measurements at the location of your AX. To do this properly, you will want to power-off the AX and only get these measurements for the DSL router.

ITunes 11.1 won't connect to AirPort Express

Hello,
I just updated iTunes to ver. 11.1.0.126 from the previous version of 11.0.5. Prior to this, everything worked fine, no issues ever with connecting to my airport express from iTunes. Now that I've updated to 11.1 I get the following message when selecting my AirPort express for streaming:
"An error occurred while connecting to the AirPlay Device 'CasaWalck AirPort Express'. The network connection failed"
The AirPort express is a bit older... an 802.11g, running the latest version firmware 6.3 and it's still attatching to my AT&T Uverse wireless home network just fine. Went into the router admin to verify all is well, and it is.
At the end of the day, it seems to be the iTunes update that caused all of this. I should also add that with the iTunes update, I also installed iCoud (which I didn't have installed before) and the latest version of Quicktime.
I'm running
- Windows 7 Home Premium Service Pack 1 on an HP tower.
- AT&T Uverse wireles modem w/WPA2-PSK (AES) encryption
- Netgear WNA1100 USB WiFi modem
- Apple AirPort Express 802.11g w/firmware 6.3
Any help is greatly appreciated. I really want to get my streaming to work again!
John

Okay, I'm logging this for anyone who might be experiencing the same issue. I kept poking around my system until I found the solution myself.
In researching this issue, I kept coming across folks who found an issue involving their Mac systems. Since I have a Windows 7 platform that didn't do anything for me. Initially I started suspecting an IPv6 compatability issue between iTunes 11.1 and my old airport express. Found nothing fruitful there (including this so you don't waste your time chasing that down). The other common theme coming up with others was their firewall. I came across on thread in particular where if they disabled thier firewall, they got iTunes to connect to their airport express/airplay device again. However, they were stuck with a choice between this working and having firewall protection. I personally just couldn't operate without a firewall. So... I kept poking around and literally stumbled on the solution.
Windows 7:
Start > Control Panel > Windows Firewall > Allow a Program or Feature Through Windows Firewall > Change Settings:
- click to highlight iTunes from the list
- click Remove
- click Allow Another Program...
- Select iTunes from the list and click Add
- Click OK so save your settings.
- Test your connection AirPlay/AirPort Express in iTunes. It should work
- Restart your machine and test to make sure it still works after a reboot. Mine did.
From what I can gather, the previous installation of iTunes logged some sort of profile or entry into the Windows firewall. Once iTunes upated to 11.1, it seems whatever worked for the 11.0.5 install was no longer compatable. By remiving and reinstalling this entry in the firewall, whatever was needed was refreshed and all is well with the world again.
For all the times this community has helped me out, I only hope I can return the favor.
John

Apple AirPort Express - Streaming Music on iTunes - Frequent Music Drop out

*Apple AirPort Express - Streaming Music on iTunes - Frequent Music Drop outs*
I have just purchased an Apple AirPort Express for the sole use of streaming music from my laptop to my home cinema system.
My system has bundles of power (Core 2 Duo, 3gb RAM, 320gb hard disk, Intel-N WiFi) and is running Windows Vista Premium. I am using the latest version of iTunes (version 8) and have it setup to play through remote speakers. I have my AirPort Express connected to my home cinema system.
When I play music on iTunes through ONLY my computer speakers I have no problem with drop outs.
However, when I play music through either (1) my AirPort Express or (2) multiple speakers (i.e. the AirPort Express and my computer speakers together) I experience frequent and unbelievably annoying drop outs in the music stream.
I have determined this has nothing to do with interference with the wireless signal and believe this is something to do with iTunes - the reason being the drop outs occur in BOTH the computer speakers AND the AirPort Express speakers (when I select multiple speakers) but does not occur when I select ONLY the computer speakers.
Please could you provide some advice on this as I am unable to use the AirPort!
Many thanks
Elliot

You don't say which Airport Express you are using and what its settings are.
There are two Airport Express models. The original model works on 802.11b/g on 2.4 GHz. The later model can do 802.11n on 2.4 GHz or 5.0 GHz. My experience is that interference when using the 2.4 GHz band creates drop-outs when sending audio from iTunes to an Airport Express. I now have an 802.11n network on 5.0 GHz and no longer have drop-outs. I also have a 2.4 GHz 802.11g network for my iPhone and other devices that can't do 802.11n. They are connected to each other by ethernet.
Interference on 2.4 GHz occurs because a lot of people nearby have wireless networks too. You may not notice the interference when doing other network activity that is not time dependant but it shows when streaming music. Using a utility like iStumbler or AirRadar I can see I am the only one using the 5.0 GHz band in range of my computer.

ITunes 10.6.3.25 on ethernet connection loses airport express speakers but iPhone 4 airplay works

Hi,
I have started experiencing a problem this past week (Aug 2012) that I see sometimes reported here. When I run iTunes 10.6.3.25 on a Win7 machine that is connected by ethernet to my router, the airport express speakers would regularly disappear. I can always connect to these airport express via airplay from my iPhone 4. In fact when the airplay speakers disappear from iTunes on the ethernet-connected machine, I can reliably make them reappear by turning on the Music app on the iPhone. But after a while the airplay speakers would disappear again. On a Win7 laptop connected via wifi to the network the same version of iTunes seems so far not to exhibit the same problem.
Has anyone discovered what the underlying problem is or found a solution?

I ran into the specific problem in another thread. There are more than 100 connections from the apple TV's to iTunes. You can do a netstat -a (windows or Mac), and verify the problem. iTunes is smart enough to stop allowing more than 100 connections but stupid to allow the ATV to create so many connections.
Now for what you really want! Set all of your ATVs to wifi only. Even setting the iTunes host to wifi might help also. I think that wifi is more unreliable, and forces connections to drop, keeping the count under 100.
I also turned off ip v6. That could help you also. I originally had problems on a Mac mini, and built a windows 7 box to try to fix the problem. The wifi trick worked on both platforms. Several of us have bug reports into apple. I have a wired house also, and am very angry to NEED to use slow wifi to overcome this problem. The ATV gen 3 has been able to keep up with 1080p over wifi, so it doesn't hurt too much. What really hurts is spending over 40 hours troubleshooting this bug.

Itunes will not stay connected to Airport Express with any Yosemite update.

Since installing Yosemite (original and updates) my itunes will no longer stay connected to Airport Express on my iMac. Any ideas?
I have no probblem at all when using ipad or other devices.
Matt

Hello mtvessell,
If you are having issues connecting to the iTunes Store, then start with the article below for some general troubleshooting to get it sorted out. If it continues, then take a look at the second article for additional support.
Can't connect to the iTunes Store
http://support.apple.com/en-us/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/en-us/TS3297
Regards,
-Norm G.

Itunes starts/stops when connecting to Airport Express

When I try and play songs via my wireless laptop, the music will stop/start as if it is trying to connect to my airport express. But, if I play the music from my desktop that is connected directly to my wireless router, it will play just fine (no pauses).
I have a Linksys 4-port Wireless G Router (model WRT54G).
Need some advice on how to get my laptop to play music without starting or stopping

It appears iTunes is indeed looking for speakers connected via airport express, but, as your router isn't an airport product, it doesn't succeed.
Try turning off the airtunes function in the iTunes preferences.

Can't get itunes to connect to airport express via air tunes

Hi,
I just bought and installed an airport express (for windows 7) everything is now connected but i can't get itunes to recognize my airport express via air tunes. I can see the multiple speakers in itunes, but when i click on it to connect to airport it just comes up with connecting, loads for about a minute then minimizes without connecting.
Has anyone else experienced this? How can i get this to work?
Message was edited by: Toddy85

You've probaby solved this by now, but if not... When upgrading itunes on a Vista or Windows 7 machine with Windows Firewall running for some reason Bonjour can't get through the firewall and thus Airplay does not work. Not good when all your Hi-fi's are connected via airport express!
I found to resolve the issue you have to install an older version of Bonjour. It won't work if you try to do this straight from Apple. So try this...
1. Firstly install and older version of itunes from the web (say version 10.1) Try www.oldapps.com
2. Then find the Bonjour file in program files
3. Cut and paste it to your desktop with its contents
4. Uninstall itunes and Bonjour via your control panel (the desktop file of Bonjour you moved will still be there).
5. Install your new version of itunes, say version 10.5, from the apple website.
6. Before opening it go to program files and cut the (newly installed) Bonjour file and paste it somewhere different to the desktop (you can't just delete it). It does not matter where you won't be needing it.
7. Now Cut and paste the old version of Bonjour you stuck on the desktop in Program files in place of the one you just moved.
8. Hey presto, Airplay, Windows firewall and your Airport Express' should all get on again.
Hope this works...
Jim

Connection to airport express fails after iTunes 10.1.1.4 upgrade !

Hi,
Before ugrading iTunes to V10.1.1.4, everything was OK and I was listening music from itunes through airTunes with my airport express V 6.3.
Since I've upgraded iTunes, when à play a song, I've the error msg "cannot connect to [airport express name]. network connection failure"
It's the second time, I've connection problems to airport express after an iTunes upgrade !
First time was just after uorgrade from iTunes 9 to iTunes 10.
I had to wait for a new iTunes upgrade to fix up the problem (nearly 1 month !)
I'm a bit angry with iTunes and that kind of problems just before christmas !
Thanks for your help !
Message was edited by: Amalthee

Yes, there's an exception for Bonjour in the firewall (Bonjour is allowed)
I've try to re-add the "APAgent" which control Airports and restart the firewall but it didn't worked...
The only solution I've found was to desactivate Windows firewall...
(Firewall of my ADSL box is activated).
Maybe I should try to repair iTunes Installation like WPLU...

Is there a way I can connect my airport express to be able to airplay the sound from my apple tv?

Is there a way I can connect my airport express to ba able to air play to my speakers the audio from apple tv?

GEESAR wrote:
hi there
is there anyway i can use the unlimited data i have from my mobile network provider (o2) on this i pod touch 4 generation the latest model NO.
and does the sim from my mobile network o2 be used in the ipod touch4 to use the unlimited minuites i have from my mobile network provider NO
if not then how do i use the unlimited data ive been given through my mobile network provider please tell me most kindly Purchase a mobile WiFi hotspot (Sometimes referred to as a MyFi), or have that service added to your cell phone.
geeeeesar also how does this ipod touch4 pick up the wifi free of charge is this possible or do you have to pay for limited data to access internet Your iPod can connect to any unsecured WiFi network that you are currently within range of. These networks can be found at your local library, some city/county government buildings, doctor's offices, Denny's, IHOP, Starbuck's, Home Depot, Lowes, Best Buy, and other merchants. Your iPod can connect to any secured WiFi network that you are within range of and that you have the password for.
thanks can i pod touch 4 generation download movies too please help thank u very much.... Yes. If your iPod has a WiFi connection and you have an account with a service like NetFlix....

How can I print from my IPAD3 to a printer connected to Airport Express?

How can I print from my IPAD3 to a printer connected to Airport Express? I have a HP printer and I can print from all my Windows PC and iMAC in the house. How can I print from my IPaD?

You cannot.
The USB port on the AirPort Express allow sharing a printer with Windows and Mac OS X, not with iOS:
"Wireless printing over USB requires a compatible printer and OS X v10.2.7 or later, Windows XP, Windows Vista, or Windows 7":
http://www.apple.com/airportexpress/#wireless-printing
"AirPrint-enabled printers connected using Bluetooth or shared through a USB port of a Mac, PC, AirPort Base Station, or Time Capsule are not supported":
http://support.apple.com/kb/ht4356
The HP ePrint app also does not provide such functionality:
Can I print from the HP ePrint mobile app using USB or Bluetooth?
No. You can only print directly to supported HP printers on a local wireless network.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01923321&lc=en&cc=us&dlc=en &product=5199463#N1176
Shlomi

After upgrading to OS 10.8.1 I can no longer scan from my Canon MP240 printer when it is connected to Airport Express.

I can no longer scan from printer (Canon Pixma MP240) when it is connected to Airport Express, although printing is no affected. However, when connected directly to MBP scanning works fine. I have tried all the standard remedies; reinstalling drivers, resetting printer system, selecting sharing options, but no luck. Previous to Mountain Lion this function worked fine. Any ideas how to regain this capability?
Thanks,
J.

I'm almost completely certain that the scanning feature worked before the update. Having said that though, I don't scan a great deal and it may be the case that when I have done, the printer was directly connected to the MBP. However, since I have a laptop it's far more logical that I would have had the printer connected to Airport Express for reasons of portability so I can't really see that I would have had the printer connected directly to the laptop. Besides this, I have no memory of having this problem previously. Therefore, I don't think my memory is to blame although of course, if it were I'd have no way of knowing!
J.

Connection to airport express dies out from iTunes after 1-3 hours

Similar Messages

Maybe you are looking for