How do set up multiple devices with multiple graphs in labview

Hello,
I am new at LabView, and we are trying to setup a test rig to measure voltage, pressure and flow rates. We are currently using a NI-6009USB box and Labview version 8.2. Our problem lies in setting up the actual measurements on separate graphs. How do i go about setting up the daq-assistant to measure mulitple devices, and graph them on their own graphs? We also need to know how to program in when measuring flow, how to convert it from square wave form to a calibrated curve?
Any help would be greatly appreciated!
Nate

When you configure the DAQ Assistant, you will be first asked to select the measurement type. Assuming that you have voltage sensors because you have the 6009, you select Analog Input>Voltage. You then get a list of devices. Since you only have one, it should be listed as Dev1. Expand that and then pick the channels you have connected to the sensors. Just like it says at the bottom of the of the channel window, you can select multiple channels with <CTL> or <SHIFT> click. After you've done that, the next window is where you select your sample rate, number of samples, etc. You can also select a custom scale for each channel. This is where you would enter any formula you have from the sensor vendor in order to convert a voltage reading to scaled units.
The output of the DAQ Assistant is a dynamic data type. You can wire this to a single graph to display all readings together or use the Split Signals function to break out individual channels for separate graphs.
Message Edited by Dennis Knutson on 02-22-2007 03:33 PM
Attachments:
Split Signals.PNG ‏4 KB

Similar Messages

Would like assistance with multiple devices with multiple iTunes accounts syncing on one PC

I have had an iPhone for some years now and have been syncing with my PC without issue (first with iPhone 3gs and now with iPhone 4s). My wife bought me an iPad 3 retina in December 2012 which syncs with the same PC as my phone and shares the same iTunes account. Apps downloaded onto one device are automatically downloaded to the other, iMessages are sent and received to both devices also.
My Wife now has an iPad mini with retina (using her own existing iTunes account which she previously used for an iPhone she no longer uses). I synchronised her new iPad mini with my PC assuming iTunes would manage the device and related account and contents separately to my existing account and 2 devices. However this has caused an issue with the sharing of apps. Since doing so I have started seeing updates available on my devices for apps which I have never downloaded, but my wife has. If I tell my iPad to update said apps, I am asked for my Wife's iTunes account password.
On doing some searching via google I now understand that I should have created a second windows profile on my PC for my wife and installed iTunes onto this profile for the purposes of syncing her device.
I would very much like to do this, but would like some assistance on the best course of action for doing so. If I proceed and created a second profile and sync her device to this, I presume I would need to tell iTunes to treat her iPad as a new device (and wonder what would happen to her existing content)? Assuming we do this, I presume the issue of my seeing her app updates would still persist?
Could someone advise if they have any experience with similar issues/queries?

How to use multiple iPods, iPads, or iPhones with one computer
http://support.apple.com/kb/HT1495
How to Share a Family iPad
http://www.macworld.com/article/1163347/how_to_share_a_family_ipad.html
Using iPhone, iPad, or iPod with multiple computers
http://support.apple.com/kb/ht1202
iOS & iCloud Tips: Sharing an Apple ID With Your Family
http://www.macstories.net/stories/ios-5-icloud-tips-sharing-an-apple-id-with-you r-family/
How To Best Use and Share Apple IDs across iPhones, iPads and iPods
http://www.nerdsonsite.com/blog/2012/06/07/help-im-appleid-confused/
 Cheers, Tom

How to set dimension level security with multiple levels

Hi,
We have hierarchy with Level 0 codes to Level 4 codes.
For e.g.
Region 1 : Level 0 code 10000, Level 1 code 10001, Level 2 code 10011, Level 3 code 10111, Level 4 code 11111
Region 2: Level 0 code 20000, Level 1 code 20001, Level 2 code 20011, Level 3 code 20111, Level 4 code 21111
Region 3: Level 0 code 30000, Level 1 code 30001, Level 2 code 30011, Level 3 code 30111, Level 4 code 31111
From SSAS role administration, I would like to assign a user permission to all Region 1 codes and only Level 3 code (30111) of region 3.
How and where do I set this kind of permission?
Thanks in advance.
Manisha

see
http://www.mssqltips.com/sqlservertip/1834/introduction-to-dimension-security-in-sql-server-analysis-services-ssas-2005/
Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

Multiple devices with multiple itunes accts on one computer.

my son got an itouch from his dad. My son has his own itunes account. how do I call up his itunes account so that it comes up with I plug his device to my Mac? (right now my itunes account automatically comes up)

you can't do it automatically. you'd need to manually sign out of your iTunes account and in to his.
if you're sharing the computer, see method one in this support article:
How to use multiple iPods, iPads, or iPhones with one computer

Haven't used icloud yet but if we have multiple devices with multiple contacts can we save each contact list to the cloud separately?

We have four separate iPhones with four separate contact list but one family apple ID. If we back each device up to the cloud using the same apple ID will it keep the lists separate?

You can share the same Apple ID for purchasng form the iTunes and app stores without any problems, but you should all used separate iCloud accounts with separate Apple IDs. (You are not required to use the same ID for iCloud and other services as you do for the iTunes store.) This will prevent you from ending up with merged data. You should also use separate Apple IDs for iMessage and FaceTime or you will end up getting each other's text messages and FaceTime calls.
This article may be of interest: http://www.macstories.net/stories/ios-5-icloud-tips-sharing-an-apple-id-with-you r-family/, as well as this video: http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l.

Multiple devices with multiple users on one itunes account

How do I get my daughters iTouch on my same itunes account so we can share apps/music but so that I don't see her imessages? Also - I don't want her messages coming across with my name. Thanks!

It's an all or nothing feature as long as everyone has full access to the Apple ID. But every device can have a custom build. You don't have to put every bit of content in the libraries on every device.
Otherwise, you need a separate Apple ID for business.

How can a calender be synced with multiple apple devices

how can a calender be synced with multiple apple devices so that all the users can be able to access the calender and also the entries done by one of them?

Hi Muneshdm,
Welcome to Apple Support Communities.
See these articles for information on setting up iCloud on multiple iOS devices, as well as how to share calendars:
iCloud: Set up iCloud on your devices
http://support.apple.com/kb/PH2609
iCloud: Share a calendar with others
http://support.apple.com/kb/ph2690
Best,
Jeremy

HT4436 What is the best way to set up business accounts with multiple ipads?

What is the best way to set up business accounts with multiple ipads?

Here are three different methods >
How to use multiple iPods, iPads, or iPhones with one computer, http://support.apple.com/kb/HT1495
This article > iOS: How to transfer or sync content to your computer, http://support.apple.com/kb/HT1296
suggests using contacts groups.
When syncing contacts, you can choose to sync all of your contacts or only selected groups.
You can select a group of contacts to which all new contacts created on your iOS device will be added.
You can set up groups in the Address Book application.
If you are all going to use the same iTunes apps library, turn off "Automatically sync new apps" in the apps tab just below the list of apps. Then you won't get new apps on your device unless you select them.

Multiple devices with the same GUID

Hi,
According to the Zenworks Command line utilities reference https://www.novell.com/documentation...a/bb15p2z.html
There exists an option to register a device with a new GUID by doing the following...
register (reg) [-g] [-k <key>] [-u <username> -p <password] <ZENworks Server addressort>
Registers the device in a Management Zone.
You can use the following options:
g - Lets you create a new device object with a new GUID and password for the device if you have multiple devices with the same GUID. When you register a device by using this switch, all the associations (policies and bundles) assigned to the original device object are removed. You cannot use this option to create a new GUID for a Primary Server or a Satellite device. The local user must have Local Administrator rights to use this option.
I would like to know if it is possible to have such a command line option for the agent installation. So built into the agent installer, a command line option to force the agent to register with a new GUID.
We are having CONTINUOUS problems with the above scenario. When we move devices from one computer lab to another and re-image the device, Zenworks keps trying to assign the same GUID to the device and this mixes up our Dynamic Workstation groups, which then affect the applicable policies to each device.
I would like to know if there is an option to tell the installer to stop remembering the GUID and simply register the device with a new guid on agent installation.
This way we can build that into the post imaging scripts which install the zenworks agent.

Hi Craig,
OK, I've had a look at the ZCM Reconcile rules and run a few tests to see if it is possible to get the machines not to reconcile (use a new GUID after imaging).
As I have explained before, sometimes this result is desired in our case especially when we move machines around from lab to lab.
So far, no matter what configuration I use, I cannot get Zenworks to generate a new GUID for a device that is getting re-imaged (without doing so only after the fact by unregistering the machine and reregistering the machine via the zac und and zac reg -g).
We use dynamic workstation groups to assign policies and bundles to machines so reconciling the devices is not necessary most of the time. We need an option to tell the machine to register with a new GUID on installation of the agent. Surely such an option can be built into the agent installer?
The options in the ZCM config management "reconcile settings" I tested with are:
Serial Number - Unticked/Unselected
Mac Address - Unticked/Unselected
Machine Name - Unticked/Unselected
Enable Differentiation - Unticked/Unselected
I then also tested:
Serial Number - Unticked/Unselected
Mac Address - Unticked/Unselected
Machine Name - Ticked/Selected
Enable Differentation - Ticked/Selected
and also:
Serial Number - Unticked/Unselected
Mac Address - Unticked/Unselected
Machine Name - Ticked/Selected
Enable Differentation - Unticked/Unselected
With all three different configurations, I re-imaged the same machine, which renames the machine via the first post imaging installation script to match the DNS name. Thereafter the Zenworks agent gets installed, which then renames the machine back to what it was registered into the Zenworks database with on first installation.
We need a method of telling Zenworks NOT to reconcile when we want it to. It should not reconcile every time and thereby rename the machine netBIOS name.
Is there any way to achieve this?
Originally Posted by CRAIGDWILSON
Quite Simple,
Let's say a HDD Dies and you replace it.
All you need to do is bring down an image and the machine will come back as it was with all the same WS and Device associations.
The same thing could apply if bringing in new Hardware.
If a new computer were to replace an old computer but the name stayed the same, everything could be automatic depending on the rules setup.
It is all a matter of how you tell ZCM to reconcile devices.
The Help in the ZCC under these items should explain how it works so you can setup your rules to meet your use cases.

Assigning ports to multiple devices with HH5

Im am trying to assign ports to each of my gaming devices (PS4, Xbox One and PC), these devices share some ports such as 3074, 80, 53, etc. I have set up the PS4, but when I tried to set up the Xbox One it wouldn't let me as the PS4 has duplicate ports.
Is there any way to set up multiple devices with the same ports?

You can only forward the same port(s) to one device.
If you forget about using port forwarding, and simply allow uPnP to allocate the ports, then you should be able to use one device at a time.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

If i have multiple devices with my icould account can they all read my text messages?

If i have multiple devices with my icould account can they all read my text messages?

Welcome to the Apple Community.
They can all share your iMessages, just make sure the settings on each device are set to send and receive from the same numbers and addresses.

How do i take one layer with multiple selections...

how do i take one layer with multiple selections and make those selections their own layer?

Yes sir. It w was really hard to explain. It is discontiguous segments that are separated by transparent areas. And I want those non transparent areas to be on their own layer. I have a photo shop file that has a bunch of buttons on them and they are on a transparent background. It is one layer. I want to select all the buttons and put them on their own layers. I can do this manually by selecting a button and cmd Just to a new layer, but when I have 200 buttons it is a daunting task.
Sent by MailWise<http://www.mail-wise.com/installation/4> – Your emails, with style.

How can i create excel sheet with multiple tabs using utl file?

how can i create excel sheet with multiple tabs using utl file?
any one help me?

Jaggy,
I gave you the most suitable answer on your own thread yesterday
Re: How to Generating Excel workbook with multiple worksheets

I have multiple devices with the same cerificate, once I have a an exception for one, FF denys access to the others. I cannot change the certificates, I need to stop FF blocking them.

I have multiple devices with the same cerificate, once I have an exception for one, FF denys access to the others. I cannot change the certificates, I need to stop FF blocking them.
== This happened ==
Every time Firefox opened
== I attempt to access a web front end on an IBM SVC device

You can't use the same certificate more than once.
See also [[Certificate contains the same serial number as another certificate]]

How do you get a line with MULTIPLE fields to WRAP ?

How do you get a line with MULTIPLE fields to WRAP ?
Good afternoon everyone...
THE PROBLEM: Why doesn’t a line with multiple fields WRAP?
HYPOTHETICAL EXAMPLE/WHAT I”D LIKE TO SEE
If I have 2 fields on a line (this is now a hypothetical example and nothing to do with my actual report)….let’s call them field A and field B. And if field A has values of all ‘X’ and field B has values of all ‘Y’…then….the normal case would be (ignore dots – only for spacing):
A……………………… B
XXXXXXXXXXXXXXXXXX YYYYYYYYYYYYYYYYY
But what if A is too long? I would want to see B wrap onto the next line like this:
A……………………………………………………B
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX YYYYYY
YYYYYYYYYYYYY
And similarly….if B is extra long, can the line print as:
A………………………. B
XXXXXXXXXXXXXXXXXXX YYYYYYYYYYYYYYYYYYYYYYYYYYY
YYYYYYYYYYYYYYYYYYYYYYYYYYYYYY
I don’t want the case where B is long and I get:
A………………… …B…
XXXXXXXXXXXXXXXXX YYYYYYYYYYYYYYYYYYYYYY
………………………..YYYYYYYYYYYYYYYYYYYYY
I can see how you can wrap an individual field like that…but how can you WRAP a line of[b] fields within the frame so it wraps to the BEGINNING of the frame on next line?
My SPECIFIC CASE
I have a report that I have stripped down to a simple structure for the purposes of this explanation.
My DATA MODEL has the main QUERY (for plant family and species data). The columns of the query are divided into 2 groups. The 1st GROUP contains the family data. Below that is the rest of the species data in a 2nd GROUP.
Linking from the 2nd species group (above) is a new QUERY to extract REGION data based on the common key field. Under this 2nd query is another group with all the REGION columns.
The LAYOUT MODEL has a group frame (the main , base one)
On top of this is a repeating frame based on the 1st group (family data).
On top of this is another repeating frame for the 2nd group (species data).
On top of this is 2 Frames on the same line line. The 1st frame contains columns from the species group .
The 2nd frame on this line is a repeating frame. The PRINT DIRECTION for this frame is ACROSS/DOWN. It repeats details of the REGION where the species is found. These columns come from this group come from the REGION QUERY and GROUP.
All fields on the report line have variable horizontal elasticity.
The problem is that when there is too much data on the line, it does NOT WRAP to the 2nd line.. It TRUNCATES.
Can the line be made to WRAP????..
In my current report, 1 of 2 things is happening:
1) All fields print on the line until it hits the page boundary and then it just stops. Truncated!
2) All fields print on the current line, then Oracle Reports throws a new page to print the REMAINDER of the long, input line
But I would like a LONG line to continue printing onto the following line of the same page.
I have tried all combinations of the elasticity fields and the ‘ADVANCED LAYOUT’ properties.
I have been focussing my attention with this problem on the frames .
We are using REPORT BUILDER V 6.0.8.26.0
Thankyou to anyone who may offer assistance.
Tony Calabrese.

Steve,
you gain 1 thing, but you lose something else!
This thing is SO frustrating!
Hey Steve! Good afternoon.
I've done as you suggested....I have a long text boilerplate item - the only 1 on the line...and it has all the column in it.
So it looks like:
&col1 &col2 &col3 &col4 &col5 etc etc etc
And the line expands nicely to each field's requirements.
And when it gets to the right page boundary...it WRAPS to the next line! Beautiful!!!
The only thing is that...when I had individual fields across the line I was able to create format triggers for those fields. And in doing so I was able to reduce the font and change the justification. I had to do that because some of the fields had to appear superscripted.
So I wanted something like (ignore the dots):
...................................ppppp
AAAA BBBB CCCCC DDDD EEEE FFFFFF
So the field of 'ppppp' appeared slightly higher on the line than the other fields...
I can't see how I can do this with a single TEXT field containing all the &COL values.
Have you ever come across anything like this?
Thankyou again,
Tony Calabrese 12/4/2007

How do set up multiple devices with multiple graphs in labview

Similar Messages

Maybe you are looking for