RVS4000 Internet Access Policy issues after FW upgrade to 1.3.3.5

Hi,
we run a small home/business network using an RVS4000v1. Everything is pretty simple and straight forward. We use 10 different Internet Access Policies (IAP) that's it. We recently upgraded the Firmware to 1.3.3.5.
Since then all IPaddresses (that is 2 IPaddresses in total) that have 24 hr access to the internet will get cut off the internet just before/around midnight. All IAPs that use a time window (e.g. 8:00 AM to 10:00 PM) are working fine (also on the next day).
The web GUI still works and the status of the routers still says its up and the WAN access is up as well. We have to reboot the router (through the webGUI) to get 24hr access again or save the same IAP again.
Reading the release note for FW 1.3.3.5 I note that there is a know issue with IAP.
>>QUOTE
The second Internet access policy does not work.
Work Around: Configure only one Internet access policy within a 24-hour
interval.
>>UNQUOTE
I am just not sure how to read it.
Is it only the second IAP that has the issue (and the IAP numbers 3 to 10 do not)? Or will only ONE IAP work and no others?
Or is the second policy that uses a 24hr setting meant to be the issue? If this was the case, could a work around be to set the time from 00:05 AM to 11:55 PM (or in my case 00:05 to 23:55)?
We appreciate your help
Andy

Friends,
The issue is resolved. I just switched off my phone and removed the battery. Inserted the battery after a minute or so and everything seems to be fine. Even the available memory shown is around 25.15 GB.I had even forgotten to take a backup before upgrading to PR 1.3. Still all my Photos,Videos,Documents are as they were before upgrading.
Thankfully i can heave a sigh of relief now
Cheers,
Goks

Similar Messages

E1200 V2 with no "internet access policy" in built-in web-based setup

I just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04
My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".
Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
Thanks!
Eric
Solved!
Go to Solution.

Very strange indeed then! My subtab only has "Parental Controls" listed.
I've compared it to the one shown here ( http://ui.linksys.com/files/E1200/2.0.00/inter_access.htm ) - and mine does not look like this at all!
I think i have a mislabeled V1 model or at least V1 software loaded,
Does anyone know if it is possible to download and reload the software that is built in to the router or do I need to return it and get a (hopefully) new one?
Thanks!
Eric

Performance Issues after an Upgrade

Hello!
We are experiencing performance issues after we upgraded to a new version of Hyperion (11.1.2.1). At this point, I am not too sure about the actual causes for this degrade in performance but I am trying to narrow down the causes and need your inputs. Please help me with your ideas.
1) What could be the causes/factors for the performance to degrade after an upgrade?
2) Does the performance of a script depend on the user credentials i.e. who is launching the script? Whether it’s the super admin of the application/application owner or an application specific admin?
3) Does the performance of the scripts depend on the place you are launching it from? For example - will the performance differ if it’s launched from MaxL Vs EAS?
Please let me know your thoughts on this.
Thanks,
- Krrish

There are a number of bugs 12600557, 12675485, 12669814, 12698488 logged in for 11.1.2.1 - If you use Internet Explorer 8 and have data forms designed to use a large number of sparse dimension members in rows or columns, you may experience performance degradation when opening the data forms.
This has been fixed in Oracle Hyperion Planning, Fusion Edition Release 11.1.2.1 Patch Set Update (PSU): 11.1.2.1.101 which is available on My Oracle Support as Patch 12666861.
HTH-
Jasmine.

Performance issues after iOS4 upgrade

hello everyone,
I had notices few issues after I upgraded my iPhone 3GS:
1- The screen is not rotating (when reading e-mails of flipping photoes).
2- The resolustion has decreased big time after the upgrade. Now the photos are shown in less resolution and they look hazy.
3- my Ipod is not working.
4- I could not restore my device via the itune.
my big question is there a real tangible benifit for this new upgrade?
I really appreciate if you can help me soon
thanks.

There are a number of bugs 12600557, 12675485, 12669814, 12698488 logged in for 11.1.2.1 - If you use Internet Explorer 8 and have data forms designed to use a large number of sparse dimension members in rows or columns, you may experience performance degradation when opening the data forms.
This has been fixed in Oracle Hyperion Planning, Fusion Edition Release 11.1.2.1 Patch Set Update (PSU): 11.1.2.1.101 which is available on My Oracle Support as Patch 12666861.
HTH-
Jasmine.

WRVS440N Internet Acess Policy Issue

Firmware Version: V2.0.0.8-ETSI
I use the Internet Access Policy to block some websites. But i cannot block domains with a hyphen inside. Then I obtain following error-message.
Invalid URL. Please check the format of the URL.
I fixed it with add the URL in the keyword blocklist, but I can't believe, that this is the right way. I think it's a bug in firmware.
Regards Goeran

I agreed with you, there are a lot of bugs in the firmware, I am not sure Cisco tets the firmware properly before it release.

Access Policy Issues on WRT600N

I dunno what the deal is but I am having issues setting up an access policy for a computer on my network. I added the ip address of the computer that I want to set restrictions on to the list of "applied pc's", then set "Allow" internet access, "everyday", "24 hours", block website "www.yahoo.com". Then I enabled and clicked save.
The problem is that after I enable this policy NONE of my other computers on the network get internet access AT ALL anymore. The computer that I set the policy on gets internet access and yahoo.com is blocked. But like I said none of my other computers can get access while this policy is enabled.

This is EXACTLY what my router is doing...
2) Access restrictions do not work, PERIOD...."ALLOW" will disable internet access for the entire subnet (regardless of the rule), and "DENY" will prevent uploading of file attachments to hotmail, myspace, facebook etc....for every computer on the subnet.
Message Edited by DSMKilla on 10-26-2008 11:08 AM
(Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 10-26-2008 11:39 AM

E71 wlan issue after firware upgrade

I just upgraded by E71 to the latest software version. The upgrade went without any issues. After the upgrade I realised that t had removed all my contacts - so I had to restore my backup(I restored the SETTINGS as well). I was using a app for my 'WiFi' (for prioritizing my access points) and after the firmware upgrade - I could not see this app at all. The following are my issues now:
1. I cannot connect to my home wifi(WEP) - it was fine before the upgrade. The first time it says - 'Connection not available' and every subsequent time it irritates by showing 'WLAN already active. Please close the connection and retry'.
2. I have tried to restore the factory settings and it still does not work.
3. I have renamed my Access point to the ones that the app was using - still no luck.
So, what are my options now? Can somebody please help? I never thought a small software upgrade could spoil my whole evening!

Hello,
I have just had EXACTLY the same problem.
I have a Nokia E71 and it was working OK before the upgrade. I just used the latest Nokia Updater and latest nokia pc suite to upgrade to 500.21.009.
The upgrade performed perfectly, and after the upgrade I restored my backed up data.
I have the exact symtpoms as psankar. I have factory reset the phone and tried again. Same problem.
Connection not available, and then connection already active. Small Wireless icon appears at top right of screen, and stays there, but there is no active connection in connection manager.
The only way to remove the wifi icon and to get the phone to attempt to reconnect is to power off the phone, but then on reconnectig then you get connection not available and then the whole cycle begins again.
Help appreciated
TIA
Alex

Access policy issues and daylight savings

I have the WRVS4400N. I have purchased a few Linksys routers in the past and have been happy with their operation. The wireless access however, was mediocre until I purchased this model. This model has great a great wireless connection. I like the fact that I can make many changes to the settings on the router without having to reboot the router. The performance of this router in combination with the cable modem has been excellent. It far outperforms the equipment that it replaced. I will normally pick a linksys product over another brand.
I am having 2 intermittent issues that are really causing me grief and an additional couple of annoying issues. I need help in fixing these issues. I have confirmed that I have the latest firmware version.
1) Some computers do not have connection to the internet. As if the security policy is confused about the time or connection. I really think this is a security policy issue, but I will let you decide.
2) There are some computers that I allow a 24/7 connection to the internet. For the rest I don’t want them to have access between the hours of 12a-6a. I have found that the connection doesn’t always shut-off. I have kids and do not want them to have access during those hours. I never had problems with my previous linksys router.
3) I am unable to set an access policy that spans the 5 min between 11:55p and 12a. In my previous linksys router I could.
4) The new daylight savings schedule is not part of my current firmware. This really threw off my security policies.
I have found that if I reboot or if I simply goto the security policy screen and click on save settings it seems to correct itself. But, I shouldn’t have to babysit it to make sure that it’s working correctly. When I am out of town I need to know that my security policies will continue to work while I am away.
Here’s my set up:
1) I have a linksys cable modem that connects me to the internet through my cable provider.
2) I have the linksys wireless (WRVS4400N) router that connects to the cable modem.
3) I have a 3Com Superstack II switch as the backbone of my network which connects to the router.
4) I have several devices connected to this router: computers, xbox, vonage phone line.

This is EXACTLY what my router is doing...
2) Access restrictions do not work, PERIOD...."ALLOW" will disable internet access for the entire subnet (regardless of the rule), and "DENY" will prevent uploading of file attachments to hotmail, myspace, facebook etc....for every computer on the subnet.
Message Edited by DSMKilla on 10-26-2008 11:08 AM
(Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 10-26-2008 11:39 AM

NSS Issues After Win10 Upgrade

I have had many of the same issues with the Comcast/Norton Security Suite that have been ID'd in the forum, but have not had a positive resolution. I have tried the downloads numerous times and the installation has failed repeatedly. I have followed the instructions suggested in the threads from "Tazman817" and "USAF", but with no luck. My screen shots are identical to Tazman's, and I have tried both the Norton Power Erase and Norton Removal Tools. I have downloaded the new install from www.norton.com.nss after deleting the Norton folders in Program files. Still no luck. I want to continue to use the Norton product, but after several hours of frustration, I am running out of patience. Are there any other's having these same issues? Are there any other potential solutions? Thank you.

Thanks for the tip, but my experience with Norton was not as successful as yours. I consulted with two techs over four hours (including phone wait time), and they used remote access to delve into the finer points of my system. They used Norton Power Eraser and Norton uninstaller, deleted Norton Program files, and even went into the Registry to make changes. Other than making registry changes, I had used the other tools prior to calling the support line. Based on the Norton Techs conclusions so far, Norton Security Suite cannot be installed on my system after the upgrade to Win 10. I am waiting a few days to find out if they can develop a fix in the future. Until then, I will be using Windows Defender and Firewall, and exploring other options. Too bad, I have liked using Norton's products.

IPhone syncing issues after iTunes upgrade

Hi
I just upgraded to iTunes 8.1.1 for Mac. During the install I got a kernel panic and had to restart. iTunes seems to be installed fine. When I connect my iPhone I get messages like "some content will not be copied to the iPhone as this computer is not authorized" or such like. So now several apps, videos and music has been wiped from the iPhone.
I tried authorizing the computer but I just get "This computer is already authorized".
there does not seem to be any particular link between the erased content. Some was purchased on the Mac and some on the iPhone, all from the iTunes store. Before I updated iTunes everything synced fine.
I can d/l the apps again direct to the iPhone but I can't find a way to get the missing music and videos back on the iPhone. Very annoying.
Would re-installing iTunes help?
Any ideas?
Thanks
Chris

Hi Chris,
Try highlighting the one of the songs that will not sync in iTunes> cilck File> Get Info, check the account name and verifying you are authorizing the computer with correct account.
If the issue persists, try removing the SC Info folder as shown here: http://support.apple.com/kb/TS1389
If you still see the issue after removing the SC Info folder, try reinstalling iTunes as shown here: http://support.apple.com/kb/HT1224
-Jason

Issue after solman Upgrade

Dears,
We were using solman 7.0, connected to ECC 5.0 server.
We configured all activities EWA,System Monitoring and all were working fine.
Now we upgraded solman to 7.01(EHP1) and R/3 to ECC 6.04 .
1 - My first concern is after upgradation it should automatically pick details but is is still showing ECC5 in product version.
We performed Read data from remote system also but still same issue.
2 - When I go to EWA or system Monitoring I only find Prd server there while in solution's logical component all dev,qas and prd servers are available.Earlier before upgrading it was showing all systems in EWA and system Monitoring.
Please suggest.
Shivam

Hello Shivam
For point #2 please look closely at the solution containing the systsem and make sure that 1) The Dev, QAS systems are included, and are highlighted greeen ( Meaning they are status "Put in Solution"). It sounds a lot like this setting is not done, therefore the systems would not show when you would try and use that solution in functions like EWA, BPMON, etc.
It sounds very much like when you create a new soltuion with PRD, QAS, DEV systems assigned, but only the PRD system is "Put in Solution" by default, so you explicitly need to right click the system in change/edit mode, and select "Put in Solution", then save.
Now why this might be the case after the upgrade, I don't have an answer, but it is worth having a check as the symptom fits this issue. I would advise you check the solution itself and ensure the DEV and QAS systems and in status "Put in Solution".
Hope this information is helpful.
Regards,,
Paul

SAP Query selection screen issues after ECC upgrade

Hi all
We have a custom query created and assigned to a custom transaction code, which after upgrade to ECC 6.0 we find that the selection screen layout is different from what was available in 4.6C system.
All the fields required are available.
However, the sequence of the fields on the screen is different from the 4.6C after the upgrade.
Can anyone help identify the issue so that the issue can be resolved?
Thanks
Vinodh S

Hi N_niki
There is no resolution as such.
We had raised a Customer message with SAP and were informed that this was expected as the procedure to execute the reports was changed in ECC when compared to 4.6 (technical changes) and hence this issue shall remain for some queries wherein the old changes need to be brought back using an option in the SAP Query.
Please refer to SAP Note # 723577 which could provide a better explanation for the issue.
Hope this helps.
Thanks
Vinodh Sudhakaran

IP Phone 7921 / 7925 roaming issues after WLC upgrade from Version 7.2 to 7.3 and / or 7.4

Hi,
We have a customer which is using a Cisco WLC 5508 and 3502I APs. As he used the 7.2.103 release, There were no issues with VoWLAN. Now he needed new APs and ordered the 2602I. To use them he needed to upgrade the WLC to a 7.3 or later release. After the upgrade, he now encounters problems while roaming with the phones. The phones were tested with FW 1.4.1, 1.4.2 and 1.4.3.
Configuration is set according to wireless voice design guides (VoWLAN DG 4.1, 7921 Deployment Guide). A Cisco TAC is also in progress, but they seem to be uncertain whether it is a wireless or CUCM issue, but I don't see a reason why it should be the CUCM when the only thing changed is the WLC Software Version.
Is there anybody who is aware of such issues and can offer help?
Thank you in advance.
Best regards,
Patrick

Hi,
we had a TAC ticket open with this customer and after some time, the TAC gave us the advise to use this release and the problems are now solved.
So for others having the same issue: If you only need to support the 2600 APs, stay with the latest 7.2 release as there are some issues with the 7.3 and 7.4 release. If the customer requires HA, AVC or any of the new features + wireless voice, be very careful as it seems that the newer releases are having problems with that. I hope that Cisco will fix this very soon.
regards,
Patrick

Web dynpro ABAP- small issue after EHC1 upgrade

Hi All,
We have a Web dynpro ABAP report and it was working fine before the EHC1 upgrade. After the upgrade we noticed that the row count in ALV greed was disappeared.
The report used to show 25 records per page and we were able to jump to the other pages by clicking on row count that was placed right below the report. Now report shows all the records and we only have scroll down option.
Any idea where to look/ how to fix this issue?
Regards,
Mike

In addition to applying that note, you also must deactivate Lightspeed rendering. To me that's too extreme of a thing to do just to get paginators. You loose the huge rendering performance improvements and it also means you can't use any of the new UI elements from 7.01.

Performance issue after PT Upgrade.

Hakan and Team ,
We recently moved from PT 8.48 TO PT8.51.18 on CRM 8.8 Application.
After the upgrade, we tremendously saw big performance issues with PeopleSoft CRM Application. It freezes almost every day and all their work-force (call center representatives) go idle. It significantly impacts their productivity and eventually losing revenue.
can you please suggest few suggestion or DOC that will help us to improve performance on application and DB side.
Deatils :-
SQL SERVER 2005
Windows 2008 R2

Hi,
Performance is always a difficult one to tackle.
It can be at so many levels, DB, Appserver, Webserver, CPU, RAM, Infra, etc.
At OOW2012, David Kurtz gave a great highly detailed presentation on this subject: CON9210 - Performance Tuning for PeopleSoft Administrators
http://www.myexpospace.com/oracle2012/smupload/scloader.cfm?SCID=257daa92-a6e8-411a-9806-2c22e56687d3
See if you can apply some of the keypoints from his presentation.
Regards,
Hakan

RVS4000 Internet Access Policy issues after FW upgrade to 1.3.3.5

Similar Messages

Maybe you are looking for