11gR2 install on Solaris 10 Issue

I am trying to install the 11gR2 Grid Infrastructure on Solaris 10 2 node cluster. I have taken care of all the pre reqs, ssh equivalence works well,, i am installing the binaries on a ZFS mounted file system and using ASM for datafiles. The installation runs fine on node 1 and continues until 65% where it hangs saying: "Copying files to node 2"
Has anyone seen this issue?
The install log has this error:
Exception in thread "Install API Thread" java.lang.NullPointerException
at oracle.cluster.deployment.ractrans.ClientHandlerSupervisor.threadCleanup(ClientHandlerSupervisor.java:914)
at oracle.cluster.deployment.ractrans.RACTransfer.cleanup(RACTransfer.java:1761)
at oracle.cluster.deployment.ractrans.RACTransfer.transferDirStructureToNodes(RACTransfer.java:749)
at oracle.cluster.deployment.ractrans.RACTransfer.transferDirToNodes(RACTransfer.java:252)
at oracle.ops.mgmt.cluster.ClusterCmd.transferDirToNodes(ClusterCmd.java:3103)
at oracle.ops.mgmt.cluster.ClusterCmd.transferDirToNodes(ClusterCmd.java:3022)
at oracle.sysman.oii.oiip.oiipg.OiipgClusterOps.transferDirToNodes(OiipgClusterOps.java:947)
at oracle.sysman.oii.oiif.oiifw.OiifwClusterCopyWCCE.doOperation(OiifwClusterCopyWCCE.java:544)
at oracle.sysman.oii.oiif.oiifb.OiifbCondIterator.iterate(OiifbCondIterator.java:171)
at oracle.sysman.oii.oiif.oiifw.OiifwActionsPhaseWCDE.doOperation(OiifwActionsPhaseWCDE.java:633)
at oracle.sysman.oii.oiif.oiifb.OiifbLinearIterator.iterate(OiifbLinearIterator.java:147)
at oracle.sysman.oii.oiic.OiicInstallAPISession$OiicAPISelCompsInstall.doOperation(OiicInstallAPISession.java:1058)
at oracle.sysman.oii.oiif.oiifb.OiifbCondIterator.iterate(OiifbCondIterator.java:171)
at oracle.sysman.oii.oiic.OiicInstallAPISession.doInstallAction(OiicInstallAPISession.java:642)
at oracle.sysman.oii.oiic.OiicInstallAPISession.access$000(OiicInstallAPISession.java:88)
at oracle.sysman.oii.oiic.OiicInstallAPISession$OiicActionsThread.run(OiicInstallAPISession.java:934)

Hi user;
You may hit a bug.Please check below and if your issue similar as them please log a SR wiht those reference
Bug 9307874: ADDING A NODE TO A RAC 11GR2 CLUSTER ENDS WITH AN SEVERE ERROR.
https://support.oracle.com/CSP/main/article?cmd=show&type=BUG&id=9307874&productFamily=Oracle
Bug 9158980: RAC 11GR2 INSTALLATION HANGS WHEN STARTING REMOTE OPERATIONS
https://support.oracle.com/CSP/main/article?cmd=show&type=BUG&id=9158980&productFamily=Oracle
Please also check below thread
Stalled Grid 11GR2 installation at 65% - Performing Remote Operations
http://www.oracle-base.com/forums/viewtopic.php?f=1&t=11244
Hope it helps
Regard
Helios

Similar Messages

Unable to install a Solaris OS in a Single disk slice

Hi,
We are unable to install the Solaris-OS on a single slice disk.
We found that, only "Solaris 10 10/08 (U6)" release can support the single slice disk installation, prior release are not. Is it true ?
We found it from "LDoms Community Cookbook " , from given link
http://wikis.sun.com/display/SolarisLogicalDomains/Section+2+-VirtualDevices
Paragraph is
" Before Solaris 10 10/08 (U6), when a backend is exported to a domain as a single slice disk, it will appear in that domain as a disk with a single partition (s0). Such a disk is not visible with the format(1m) command and its partition table can not be changed. A single slice disk will not be visible from the Solaris installer and can not be select as a disk device on which Solaris can be installed. "
Our Configuration are
sc> showhost
System Firmware 6.6.4 Sun Blade[TM] T6300 2008/07/01 02:03
Host flash versions:
OBP 4.28.9 2008/06/30 21:26
Hypervisor 1.6.4 2008/06/06 04:57
Sun Blade T6300 Server Module POST 4.28.6 2008/05/23 12:35
-bash-3.00# cat /etc/release
Solaris 10 8/07 s10s_u4wos_12b SPARC
Copyright 2007 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 16 August 2007
We Installed a 127127-11 patch also.
-bash-3.00# ldm -V
Logical Domain Manager (v 1.0.3)
Hypervisor control protocol v 1.1
Using Hypervisor MD v 1.1
System PROM:
Hypervisor v. 1.6.4 @(#)Hypervisor 1.6.4 2008/06/06 04:57\015
OpenBoot v. 4.28.9 @(#)OBP 4.28.9 2008/06/30 21:26
Use below command to add single slice disk
*# ldm add-vdsdev options=slice /dev/dsk/c0t1d0s3 vol3@primary-vds0*
Getting error in between installation,
ERROR: No disks found
- Check to make sure disks are cabled and powered up
Please help us to, resolve this issue. Thanks a lot.
Best Regards,
Parvez Memon.

Hi,
Whenever i try to installed the patch 137137-09, it required a below patch
0 For patch 137137-09, required patch 138866-01 does not exist.
And try this then
# patchadd 138866-01
The following requested patches will not be installed because
the packages they patch are not installed on this system.
0 No Packages from patch 138866-01 are installed on the system.
No patches to install.
I am not able to install this patch 138866-01, even i try with 138866-02 but not success.
Thanks for your reply, please help to resovle the same.
Regards,
Parvz Memon

What packages are required for an 11.2.0.3 install on Solaris 11?

Where can I find information on which packages are required to install Oracle 11.2.0.3 on Solaris 11?
The documentation only mentions Solaris 10. I tracked down the packages required for Solaris 10, and most of them are either included in the GA release of 11 or obsoleted.
There are however a couple of packages that are missing from the base install of Solaris 11:
SUNWarc (renamed to):
     * consolidation/osnet/osnet-incorporation (installed)
     * developer/library/lint (missing)
SUNWhea (renamed to):
     * consolidation/osnet/osnet-incorporation (installed)
     * system/header (misising)
So it looks like developer/library/lint and system/header are packages from required for Solaris 10 that are missing on 11. The installer however doesn't check for any packages whatsoever.
Does that mean it's safe to install the database?
Edited by: 894946 on Nov 21, 2011 8:38 AM

Here is list of packages you need in order to install Oracle 11gR2 on Solaris 11:
SUNWarc SUNWbtool SUNWhea SUNWlibms SUNWpool SUNWpoolr SUNWsprot SUNWtoo SUNWlibm SUNWuiu8 SUNWfont-xorg-core SUNWfont-xorg-iso8859-1 SUNWmfrun SUNWxorg-client-programs SUNWxorg-clientlibs SUNWxwfsw SUNWxwplt
Some of the above are installed by default which you can find by:
pkginfo -i SUNWarc SUNWbtool SUNWhea SUNWlibms SUNWpool SUNWpoolr SUNWsprot SUNWtoo SUNWlibm SUNWuiu8 SUNWfont-xorg-core SUNWfont-xorg-iso8859-1 SUNWmfrun SUNWxorg-client-programs SUNWxorg-clientlibs SUNWxwfsw SUNWxwplt
I believe you will only have to install the following:
pkg install compatibility/packages/SUNWxwplt SUNWarc SUNWhea SUNWxorg-client-programs SUNWxorg-clientlibs
Cheers

11gR2 installation on Solaris failed with prereuisite 124861-15

The 11gR2 installation on Solaris 10 sparc failed with prereuisite 124861-15.
When I tried to install the patch 124861-20, it failed with the following(see below):
I have Sun Studio 12-2 installed on the system.
It was complaining that some packages (SPROmrcom, SPROlangx, SPROlang,SPROsunms ) are not installed.
Where can I get these packages? Should not it be included in the Sun Studio 12-2 installation?
Thanks.
Zhigang
# patchadd 124861-20
Validating patches...
Loading patches installed on the system...
Cannot find package name, arch or version in pkginfo file /var/sadm/pkg/IR/pkginfo.
Done!
Loading patches requested to install.
Done!
The following requested patches have packages not installed on the system
Package SPROmrcom from directory SPROmrcom in patch 124861-20 is not installed on the system. Changes for package SPROmrcom will not be applied to the system.
Package SPROlangx from directory SPROlangx in patch 124861-20 is not installed on the system. Changes for package SPROlangx will not be applied to the system.
Package SPROlang from directory SPROlang in patch 124861-20 is not installed on the system. Changes for package SPROlang will not be applied to the system.
Package SPROsunms from directory SPROsunms in patch 124861-20 is not installed on the system. Changes for package SPROsunms will not be applied to the system.
Checking patches that you specified for installation.
Done!
The following requested patches will not be installed because
the packages they patch are not installed on this system.
0 No Packages from patch 124861-20 are installed on the system.

Hi,
The 11gR2 installation on Solaris 10 sparc failed with prereuisite 124861-15.
When I tried to install the patch 124861-20, it failed with the following(see below):
I have Sun Studio 12-2 installed on the system.
It was complaining that some packages (SPROmrcom, SPROlangx, SPROlang,SPROsunms ) are not installed.
Where can I get these packages? Should not it be included in the Sun Studio 12-2 installation?
Thanks.
Zhigang
# patchadd 124861-20
Validating patches...
Loading patches installed on the system...
Cannot find package name, arch or version in pkginfo file /var/sadm/pkg/IR/pkginfo.
Done!
Loading patches requested to install.
Done!
The following requested patches have packages not installed on the system
Package SPROmrcom from directory SPROmrcom in patch 124861-20 is not installed on the system. Changes for package SPROmrcom will not be applied to the system.
Package SPROlangx from directory SPROlangx in patch 124861-20 is not installed on the system. Changes for package SPROlangx will not be applied to the system.
Package SPROlang from directory SPROlang in patch 124861-20 is not installed on the system. Changes for package SPROlang will not be applied to the system.
Package SPROsunms from directory SPROsunms in patch 124861-20 is not installed on the system. Changes for package SPROsunms will not be applied to the system.
Checking patches that you specified for installation.
Done!
The following requested patches will not be installed because
the packages they patch are not installed on this system.
0 No Packages from patch 124861-20 are installed on the system.
Refer my post *11gR2 Installation Error with patch 124861-15 as pre Req*
http://appsdbaworkshop.blogspot.com/2010/11/11gr2-installation-error-with-patch.html
thanks,
X A H E E R

Oracle Database 11gr2 rac on solaris 10 using ACFS and asm as storage

Can i get any step by step document to install 11gr2 rac on solaris 10.
My database is two node rac. I am using ASM as storage. So i need a document which should very easy to understand.
thanks in advance

Hi,
Can i get any step by step document to install 11gr2 rac on solaris 10.
My database is two node rac. I am using ASM as storage. So i need a document which should very easy to understand.Refer below link:
http://www.oraclemasters.in/?p=961
Configure storage as per your requirement.
thanks,
X A H E E R

FF 20 installed on Solaris 10 SPARC, will not run, crashed on start-up.

Building new non-global zone w/Solaris 10 - Solaris 10 5/08 s10s_u5wos_10 SPARC.
Installed fresh download of V20 - firefox-20.0.en-US.solaris-10-fcs-sparc.tar.gz. Installed with no issues.
FF crashing immediately upon start up. I get the FF window, paints a box in the middle. Shows transfering data from either mozilla.org or mozilla.analytics.org. Crashed with core dump before any actual download is seen.
I installed V 18.0.1 and am seeing almost the same results. FF comes up but then crashes as sson as you try and do anything.
I have several core dumps available if anyone can read them..

There were no specific error messages. The launch attempted as described above. The browser would then just go away and then I get -
[1] Segmentation Fault ./firefox (core dumped).
I generated several core dumps. They are attached below. The file is a tarball of a few gzipped cores.
I have tried twice to 'upload' the files. The first was 5 cores 440 MBs. I then tried just a single core, around 90 MBs, compressed. Both failed. Is there a better way to directly upload files of this size for your review?

LMS 4.0 - Install on Solaris 10 aborts after DHCP-check

Hi all,
on solaris 10 (HW T5140) I tried to install from orignal DVD, suddenly after
answering the licensing questions with [y] setup.sh aborts with no error-message
directly after checking DHCP.
INFO: Checking DHCP..
INFO: DHCP not enabled in this machine.
INFO: BUILD_ID is SOL_LMS4_0_20100906_0753
INFO: ITOOLS_BUILD_ID is SOL_ITOOLS4_0_MAIN_20100905_1742
<abort>
Are there any known issues with install on solaris?
Thanks a lot
Lothar
This is output of install-log
======================================================================
Started : Tue Jul 5 07:41:20 CEST 2011 ======================================================================
================- Software Installation Tool Started -================
Welcome to CiscoWorks LAN Management Solution 4.0 Applications setup program.
======================================================================
INFO: Executing /cdrom/lms4_0_sol/install/correctnmsver.sh
Press ENTER to read/browse the following License Agreement:
INFO: You must accept this License Agreement to proceed with the installation.
INFO: If you enter N/n, the installation will exit.
Do you accept all the terms of the License Agreement? (y/n) [n]:
INFO: Environment variables in this machine
AIX_MIN_RAM=131072
AIX_MIN_SWAP=262144
AIX_OS_VERSION=5.5
ANILOG=/var/adm/CSCOpx/log/ani.log
CSCO_ADM_FILE=/tmp/cscotmp/CSCO.admin
CWLOG=/var/adm/CSCOpx/log/dmgtd.log
DEBUG=0
DEF_IU_ROOT=/opt/CSCOpx
DISKSPACE=0
DO_UPGRADE_FILE=/var/tmp/csco_do_upgrade
EDITOR=vi HISTLOGFILE=/var/tmp/Ciscoworks_install_20110705_074119.log
HOME=/
HPX_OS_VERSION=5.5
HP_MIN_RAM=262144
HP_MIN_SWAP=1048576
HZ=100
INSTALL_MODE=NEW
IU_DBDIR=/db/data
IU_NAME=CSCOpx
IU_ROOT=/opt/CSCOpx
LC_ALL=C
LC_OS=sol
LD_LIBRARY_PATH= LOGFILE=/var/tmp/Ciscoworks_install_20110705_074119.log.new
LOGNAME=root
LOG_NAME=Ciscoworks_install_20110705_074119.log
MAIL=/var/mail/root
MESSAGES=/var/adm/messages
OS=SOL
PATH=/usr/sbin:/usr/bin:/usr/ucb:/usr/sbin:/usr/bin:/usr/etc:/usr/ucb:/usr/sbin:
/usr/bin:/usr/etc:/usr/ucb
PRODUCT=CSCO NM
PROFILE=0
PWD=/cdrom/cdrom0
REQ_OS=SunOS
SERVER_EXP=[C]SCOpx
SETUPDIR=/cdrom/lms4_0_sol/install
SHELL=/bin/bash
SHLVL=2
SINGLEINSTALLER=TRUE
SOL_MIN_RAM=131072
SOL_MIN_SWAP=131072
SOL_OS_VERSION=5.10
SWMODOPTS=-xloglevel=0
SWOPTIONS=-x reinstall=true -x reinstall_files=true -x allow_multiple_versions=t rue -x write_remote_files=true -x autoselect_dependencies=false -x match_target= false TERM=vt100 THREADS_FLAG=native TOC=disk.toc TZ=Europe/Berlin
UPGRADE_VERSIONS=2.* 3.0 YES_PUMP=/cdrom/lms4_0_sol/install/install/yes.sol
_=/sbin/sh
INFO: Checking DHCP..
INFO: DHCP not enabled in this machine.
INFO: BUILD_ID is SOL_LMS4_0_20100906_0753
INFO: ITOOLS_BUILD_ID is SOL_ITOOLS4_0_MAIN_20100905_1742

Hi Joe,
thanks a lot for your hint, the problem is solved with editing /etc/release.
There should be a user-information pointing to the source of the problem, just aborting
the install-script is not very nice.
Do you know whether this "/etc/release-abort" is present with update to LMS 4.01 install-script
and other patches?
I like this forum
Lothar

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Help with Video Card Install on Solaris 8

I have a video card with nvidia4 chipset. After installing solaris 8 on my system I get a screen that is too big to fit on the monitor, so I have to scroll down to see everything. Plus it displays 16 colors. I tried to install the FreeBSD drivers that are availble on the nvidia site but could not run "make" command. Anyone know how to solve this?

There are two options:
1. Install the latest Solaris 8 x86 video driver patch109401-14
available at:
http://sunsolve.sun.com/pub-cgi/show.pl?target=patches/xprod-Solaris_x86IntelDrivers&nav=pub-patches
This may add native support for your nvidia chipset. If it doesn't,
then you have the option to try the new VESA driver which is
included with this patch as well - the VESA driver is supposed to work
on all cards that have the necessary VESA support bios routines.
2. Install the "Solaris XFree86 Video Drivers and Porting Kit"
http://soldc.sun.com/developer/support/driver/tools/video/video-index.html
It adds support for many video cards by using XFree 4.2.0 video
driver modules. It also includes another variant of the VESA driver.

Memory Management comparison between Database 9208 and 11gR2 on Sun Solaris

Hi All,
Need some case studies which would help understand how Memory management is done in 9208 and 11gR2 on Sun Solaris SPARC
Also wanted some real time data which says 11gR2 manages Memory and CPU better than 9208. Some comparison Graph between 9i and 11gR2.
Any information will be of great help.
Thanks everyone for your support.
Thanks
Abdul

please see if below helps :
http://www.oracle.com/global/de/upgradecommunity/artikel/upgrade11gr1_workshop2.pdf
http://www.dba-oracle.com/oracle11g/oracle_11g_memory_target_parameter.htm
Regards
Rajesh

What are all the Softwares i can install on Solaris 8

Hi,
Can anyone tell me what are all the Softwares i can install on Solaris Machine.
If I want to develop a web Based appalication what are the necessary things i have to do.
What are all the major application can develop?.
Is there any already Developed site or some demo which we can see online?
I will be very thankful i you provide some related information regarding this.
THanks in Advance.

Hi,
You can check out http://soldc.sun.com website and select Software.
This list the categories of Sun Software, freeware, Web Start Wizard
much more information.
...jagruti

How to install Sun solaries 9 or 10.

Hi,
I am trying to install Sun solaries 9 or 10.over AMD 64.
Please guide me to install sun on AMD.
Any help greatly appreciated.
Thanks,
Chandan.

The very first thing you should do is go over the HCL or Hardware Compatability List. The most likely problems you will run into are the show stoppers, first and most likely will be the network card, if you have an onboard card that is part of the mainboard find out what kind it is and then check the HCL, if it is not there then pickup a PCI network card that is on the HCL list. Second will be the video, again find out with the HCL, worst case is you will get it installed and the X server won't work right. Again you may end up picking up an AGP or PCI video card that is supported.
As far as installing it's just a matter of booting of the installer CD and following the directions, take all the defaults first then do a bit of research on drive slicing and install it a second time.
I have not had good luck with the DVD's no matter whether they are going on a Intel, AMD or a SUN platform.

List the tape drives installed in solaris

Hi ,
Can some one please let me know how can I display the tape drives which is installed in Solaris (below Version 8)
In solaris 8 we can use cfgadm , However below 8 other than prtconf is there any command or way to findout the devices installed . prtconf and sysdef command outputs are too difficult to digest ,
Thanks
Dileep

Yes I can see the following things .
I would like to use a command which will list all the devices installed in a user friendly manner .
root on LIVE netra1 # ls -l *hbn<br />
lrwxrwxrwx 1 root other 52 Jul 3 1998 0hbn -> ../../devices/sbus@3,0/SUNW,fas@0,8800000/st@4,0:hbn
lrwxrwxrwx 1 root other 50 Jul 3 1998 1hbn -> ../../devices/sbus@a,0/QLGC,isp@2,10000/st@1,0:hbn
lrwxrwxrwx 1 root other 50 Jul 3 1998 2hbn -> ../../devices/sbus@a,0/QLGC,isp@2,10000/st@2,0:hbn
lrwxrwxrwx 1 root other 50 Jul 3 1998 3hbn -> ../../devices/sbus@a,0/QLGC,isp@2,10000/st@3,0:hbn
lrwxrwxrwx 1 root other 50 Jul 3 1998 4hbn -> ../../devices/sbus@a,0/QLGC,isp@2,10000/st@4,0:hbn
Thanks
Dileep

Unable to install open solaris

Dear all,
We have sun sparc T5220 server with solaris 10/U7.we are trying to install open solaris.But geting error can not open boot device,using same cd we are able to install normal sparc server.please help me.
Regards
kk

Uninstall iTunes and all related components. You may need to do this more than once.
(99935)

Can oracle 11g installed on solaris 8 ?

Can oracle 11g installed on solaris 8 ?
Other what is the minimum solaris supported to install oracle 11g.
Thank you in advance..

[email protected] wrote:
Can oracle 11g installed on solaris 8 ?
Other what is the minimum solaris supported to install oracle 11g.
Thank you in advance..In general, each product has an installation manual - found through http://docs.oracle.com and possibly http://tahiti.oracle.com and the install manual clearly identifies the (minimum) support OS and Release information.

11gR2 install on Solaris 10 Issue

Similar Messages

Maybe you are looking for