2504 Controller - increase supported clients

I am looking at the settings of a Cisco 2504 wireless controller and I can only see it supporting up to 200 clients per radio and it is not letting me change it to a value higher than 200.
However, the guide below states that it supports up to 1000 clients (I assume they have to be split 500/500 per radio). How do you get to that number? Do you need to buy/apply an additional license for that?
http://www.cisco.com/en/US/prod/collateral/modules/ps2706/at_a_glance_c45-652653.pdf

1000 value you refer is the max number of client database entries 2500 can handle. Not for a single AP.
200 value is per radio/per AP max number of clients and not controller specific. Again this value is theoratical max & you should not have that many clients per AP. Practicaly 25 max per AP is good guideline.
You do not want to have any other licence other than number of AP you want to support by this WLC.
Hope this clears your query
Rasika
**** Please rate all useful responses ****

Similar Messages

  • Support for Aironet 1040 and 2504 Controller

    Are there any plans to provide support for Aironet 1040 series access points and the 2504 controller?  I see where the 1140 series is supported and thought the 1040 would follow.  If there are no immediate plans for full support, will OnPlus at least recognize the devices and alert if they go down, which is my main concern?

    Hi Anthony,
    I know we do have planned support for the 1040 in the future but I do not have dates at this time. Regarding a device going down, an ICMP host monitor can be configured on any device in OnPlus.
    For more information, watch this quick video, on setting up monitors:
    http://www.youtube.com/watch?v=brCc2JB-gfc&feature=plcp
    Thanks,
    The OnPlus Team

  • Whether 40Mhz Bandwidth is supported on 2504 controller

    I found 20Mhz bandwidth enable option in 2504 controller.But what about 40 Mhz .The access points(1142) are dual band...I hope it should support in 2504 controller also.If there is no option of 40Mhz ,Please Correct me

    Just like what Sarvanan said, 40 MHz is only available on 802.11a (5GHz) and not on 802.11b/g (2.4GHz).
    However, in old versions of code (6.0.182 or something like that) for wirleless controller I remember the 40 MHz was also available for 2.4 GHz (802.11b/g). They recognized later it is not feasible to add it to 2.4 GHz so they removed it from later releases.
    HTH
    Amjad

  • 2504 controller + 2602 APs = wireless clients connectivity problems

    Hello, everybody!
    I have a connectivity problems of wireless clients. The symptoms are:
    1) Some clients receive 169.254.x.x., instead a correct DHCP addresses, less in a minute connection drops, and in controller's "Monitor" > "Clients" tab these clients are marked as "Excluded".
    2) Most of the clients receive the correct addresses from DHCP (192.168.2.x), but also loose connection soon.
    3) Wireless clients with correct addresses can't ping each other, gateway and an address of the controller's dynamic interface (all of them are in same subnet).
    4) And the most suspicious problem is that some machines are unable to connect to APs after several attemps to do that. I mean, I configure controller and change some options, trying to understand, whether they were applied or not and constantly connect and disconnet certain PC to the SSID. After five or ten attempts I can't connect to the SSID. During these attempts, the others PCs stay connected, without interruptions, and they could be reconnected again. It's like some kind of port security works, but I'm not sure...
    Do you have any ideas which options should I configure?
    My configuration:
    I have three interfaces on the controller: virtual, management (default) and dynamic (it is set to the WLAN)
    I have one SSID, WPA/WPA2, AES/TKIP, authentication PSK.
    My clients are a/b/g/n, all are permitted on the controller. No custom security policies were applied.
    All the devices are in a single room: controller, one AP and different clients: desktop, notebooks, iPad, Nokia Lumia, etc.
    I have an internal DHCP Server on the controller and it works perfectly well.
    I can provide all the screenshots required from web-interface of the controller...
    Many thanks in advance for all ideas that you have about these problems...

    Hi, there!
    The problem was solved.
    1) APIPA address receives only single machine with Win8 - I think there are some firewall issues
    2) Other devices have been loosing connection because they were mobile devices, like iPad and Lumia. If you keep working with it, it doesn't drop the connection
    3) The dynamic interface address and gateway address were inaccessible because i had not used an appropriate port on the controller. =)))) Firstly, it was just a guess, but it proved.
    Now, everything works with WPA2, AES, PSK...
    It is a very good day!)
    The only question remains: why I can't connect machines, which have a static IP? During the controller initialization, I said "yes" for permitting static IPs...
    Guys, many thanks for your help!

  • IMP: Cisco AIR-CAP1602 &1532 not joining 2504 Controller issue

    Dear Team, We have Cisco wireless implementation in clients premises. We have 8 indoor AP (AIR-CAP1602E-AK9) and 2 Outdoor AP (AIR-CAP1532I-AK9) . Seven indoor APs are able to join the 2504 controller, but 1 indoor AIR-CAP1602E AP is not joining and signal is RED continuously while as outdoor AP AIR-CAP1532I-AK9 signal goes blinking from green, red to amber continuously and is not downloading LWAPP image from the controller even after hard reset.
    The output for both APs shown below-
    1) AIR-CAP1602E-A-K9:
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvara
    ap: reset
    Are you sure you want to reset the system (y/n)?y
    System resetting...
    Boot from flash
    IOS Bootloader - Starting system.
     FLASH CHIP: Spansion S25FL256
    Xmodem file system is available.
    flashfs[0]: 14 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 418304
    flashfs[0]: Bytes available: 31517696
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 18:e7:28:d1:9b:05
     ************* loopback_mode = 0
    The system is unable to boot automatically because there
    are no bootable files.
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvarag
    Same event repeating, failed to reset and reboot device
    2) AIR_CAP1532I-A-K9 (Outdoor AP):
     *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_47:32:e4'running version 7.5.102.0 is rejected.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 100.1.1.20
    signal goes blinking from Grean, Red to Amber continuously.
    Failed to download LWAPP image from the controller even after hard reset.
    Default image: 7.6.95.12
    Logs and screen shot attached
    Please advice. 
    Thanks
    Aakash

    Hi please note the details below-
    AIR-CAP1602E-A-K9:
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvara
    ap: reset
    Are you sure you want to reset the system (y/n)?y
    System resetting...
    Boot from flash
    IOS Bootloader - Starting system.
     FLASH CHIP: Spansion S25FL256
    Xmodem file system is available.
    flashfs[0]: 14 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 418304
    flashfs[0]: Bytes available: 31517696
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 18:e7:28:d1:9b:05
     ************* loopback_mode = 0
    The system is unable to boot automatically because there
    is no bootable files.
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvarag
    Can't reboot device!
    WLC-SYSLOG
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.5.102.0
    Bootloader Version............................... 1.0.18
    Field Recovery Image Version..................... 1.0.0
    Firmware Version................................. PIC 16.0
    Build Type....................................... DATA + WPS
    System Name...................................... Cisco_47:32:e4
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
    IP Address....................................... 100.1.1.20
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 2 hrs 18 mins 39 secs
    System Timezone Location......................... (GMT -6:00) Central Time (US a                                                                                        nd Canada)
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    --More-- or (q)uit
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +32 C
    External Temperature............................. +37 C
    Fan Status....................................... 4000 rpm
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 3
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ 24:E9:B3:47:32:E0
    Maximum number of APs supported.................. 15

  • New bought 2504 Controller not copatible with 1702 APs

    Hi!
    Just got a 2504 Controller with 1702 APs, which are not joining the controller by known reasons.
    (Cisco Controller) >*spamApTask1: Dec 16 22:20:10.288: f0:7f:06:c0:55:80 ApModel: AIR-CAP1702I-E-K9
    *spamApTask1: Dec 16 22:20:10.288: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Dec 16 22:20:10.289: f0:7f:06:c0:55:80 ApModel: AIR-CAP1702I-E-K9
    *spamApTask1: Dec 16 22:20:10.289: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Dec 16 22:20:16.135: fc:5b:39:6e:26:9c ApModel: AIR-CAP1702I-E-K9
    But now I have to buy a SmartNET Subscription to get the bug-free Software for my controller, because software problems are not covered in the warranty? Is there any other Solution?
    New controller running on 7.6.130.0
    Regards
    Alfred

    Well that is too bad.  Maybe ask the company whom you bought the WLC or if you have a Cisco SE to provide you with the code. The only other option is to return it and order the WLC with v8.0, but you will be stuck on that not so good code. The 2504 w/5 AP license, you can find a SMB smartnet for cheap that can give you access to the image download. It's really up to you, but the v8.0 that is currently out is the first version and... well, do I have to say more. I won't use that version, and my customers whom have had to go with that version because of access point support is not too happy to say the least. When the newer version comes out, they will have to upgrade. 
    -Scott

  • Cant Connect Cisco AIR-CAP 3602 with 2504 controller

    Im trying to have one of our APs join our controller. No matter what I do, i cant get it to join the controller.
    The controller has the right OS, I had to upgraded it 7.4 to support the 3600...
    Both the controller and the AP has the same time and date.
    But Im getting this from my AP:
    *Oct 30 14:49:26.043: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Oct 30 14:49:26.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:26.083: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:27.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:27.095: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:27.103: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Oct 30 14:49:28.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:28.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:28.131: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:28.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:28.147: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Oct 30 14:49:29.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:29.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:29.167: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:30.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:36.083: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 14:49:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    Anyone can help me please?
    Thanks....

    AP is connected directly to one of the ports on the 2504 controller.
    I can move it to a POE switch, if needed.
    Here is the output after I boot up the AP:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Macronix Mirrorbit (00C2)
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Ethernet speed is 1000 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1"...###########################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 8 seconds.
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1;flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1'
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"...###############################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    Initializing flashfs...
    flashfs[3]: 43 files, 9 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 31739904
    flashfs[3]: Bytes used: 16767488
    flashfs[3]: Bytes available: 14972416
    flashfs[3]: flashfs fsck took 8 seconds.
    flashfs[3]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 244 entries (64 SGI/104 BF variants)
    Radio1  present 8764 8000 0 88000000 88010000 4
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
    Processor board ID FTX1731GQYY
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.5.102.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 4C:00:82:77:32:7B
    Part Number                          : 73-14521-02
    PCA Assembly Number                  : 800-37501-02
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC17273HG4
    Top Assembly Part Number             : 800-35852-02
    Top Assembly Serial Number           : FTX1731GQYY
    Top Revision Number                  : C0
    Product/Model Number                 : AIR-CAP3602I-A-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:11.355: FIPS IOS test Image Checksum successful
    *Mar  1 00:00:11.355: FIPS IOS test Crypto RNG DEK Key Test successful
    *Mar  1 00:00:11.355: FIPS IOS test SHA-1 successful
    *Mar  1 00:00:11.355: FIPS IOS test HMAC-SHA1 successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Decrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS AES CMAC Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Decrypt successful
    *Mar  1 00:00:11.387: FIPS IOS test RSA Signature Generation successful
    *Mar  1 00:00:11.391: FIPS IOS test RSA Signature Verification successful
    *Mar  1 00:00:11.391: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:11.391: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
    *Mar  1 00:00:11.847: Registering HW DTLS
    *Mar  1 00:00:14.647: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:26.811: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    *Mar  1 00:00:26.811: %SNMP-5-COLDSTART: SNMP agent on host AP4c00.8277.327b is undergoing a cold start
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Jul  4 23:55:50.051: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Jul  4 23:55:50.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Jul  4 23:55:50.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Jul  4 23:55:51.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Jul  4 23:55:53.319: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.319: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.819: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
    *Jul  4 23:55:53.819: DPAA Initialization Complete
    *Jul  4 23:55:53.819: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Jul  4 23:55:54.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
    *Jul  4 23:56:13.191: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Jul  4 23:56:14.279: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.279: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.371: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:16.371: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:18.895: Logging LWAPP message to 255.255.255.255.
    *Jul  4 23:56:23.627: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.1.150, mask 255.255.240.0, hostname AP4c00.8277.327b
    Translating "CISCO-CAPWAP-CONTROLLER.pti.local"...domain server (10.3.1.32)
    *Jul  4 23:56:34.559: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Jul  4 23:56:34.567: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.pti.local
    *Jul  4 23:56:44.567: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 15:05:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    *Oct 30 15:05:18.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50

  • 2504 controller died

    Anyone ever had an online 2504 controller crash after upgrade to the point where even console port does not put anything out? Perfectly working 2504 running 7.0.116 ran upgrade through web GUI to 7.2. GUI showed perfect transfer, save etc... Asked for save before reboot. Select yes. Controller reboot and now it sits with following status lights:
    Power-green
    SYS - amber blinking
    ALM - amber solid
    Nothing out of console
    Thx //art
    Sent from Cisco Technical Support iPhone App

    Thanks! I've done many up and down on different platforms and I would have bet a paycheck on consistent upgrades.....until now. Even when you use the wrong software, bad transfer...these devices tell you. This one told me everything was good up until it said you need reload. Save and reload and it never came back. NOTHING on console. Never seen that before.
    Thanks again Scott. Appreciate your support in this community.
    //art
    Sent from Cisco Technical Support iPhone App

  • Config storage confusion 2504 controller with CAP702I

    HI all,
    I've been tasked with the rollout of the above mentioned hardware, and I've managed to get so far, but it seems I cannot do a 'copy running-config startup-config' on the CAP702I Aironet access points.
    ive got then registered with the controller and radios turned on but the problem is that it the power is cycled the radios turn off, I can SSH into each AP and manually turn them on and it works all fine except I shouldn't need to do that.
    If anyone could give me a clue as to how to change the ap config to either store the config with radios enabled on restart on the device itself or guide me through storing the config on the 2504 controller and pointing to it on the ap devices for their startup, it would be much appreciated.

    So simply wireless clients are not getting ip address from the DHCP scope defined for them on AD DHCP server.
    few  facts about DHCP handling on WLC:
    - With DHCP proxy enabled , the controller acts as relay agent.
    Simply you configure primary or may be secondary DHCP server under the interface config.
    When the client starts the DHCP process the controller will rekay the clients DHCP packets
    in unicast form.
    - With DHCP proxy disabled , the controller will not intervene at all, and the client traffic will be sent
    as broadcast. If the DHCP server is on different VLAN , you have to configure relay agent under the gateway
    of the client vlan so that it can reach the DHCP server.
    Please make sure to rate correct answer

  • Hosts having connection issue, 2504 controller

    Hello,
    We have a Cisco 2504 controller and approximately 35 AP's.
    Some of the AP's are located directly above each other (on another floor).
    When I run a basic annalyzer, it appears that there is some adjacent AP traffic, the controller has some of the close AP's with the same channel, so there is some RF interferance.
    The AP's currently are all setup for "G" and majority of the AP's are 1200 series, most of them are 1242's.
    Should and can the AP's be set with static channels so that there is no adjacent signals?
    If so where in the controller can that be done?
    Any help would be truly appreciated, we are a school with an iPad program, so the amount of connects is quite high as well as the availability to have internet acces.
    Thank you for anytype of help you can provide.
    jim

    If you don't want the WLC to control the RF using RRM, you can manually set each ap and its radio statically. On the wireless tab, click on either 802.11an or 802.11bgn and the all the way to the right of the ap, there is a blue triangle. Hover the mouse over that and click configure, there you can set the channel and power leave for that radio on that ap. You will have to do each radio and ap. Hope this helps.
    Sent from Cisco Technical Support iPad App

  • AP541n with 2504 controller how to

         is there a step by step guide on how to manage AP541n with a 2504 controller?
    I have done the initial config on the 2504 but somehow the AP does not join and i can not find what would be a correct setting for the AP. How does that work anyway. In all documentation i found the AP somehow finds the controller, but in my case it does not.                  

    Hello Frank,
    I recently retired a number of 541's because they do not support an enterprise wireless configuration like you are attempting.  Between themselves they can form a cluster but they are not able to join a with a controller.
    You will need new access points to use with your WLC.

  • Does URL Services support client side script?

    My ASP page it built as a portlet, and displays fine but it
    won't submit. When I view the Source in my browser, Portal
    didn't include any of my client side vbscript script, then html
    is there but everything else is missing....
    Question: Does URLServices support client-side VBScript?
    I am using some vbscript for validation purposes and then
    using the document.ChangePassword.submit() to submit the
    form.
    If URLServices doesn't support it, then URLServices is totally
    useless... Everyone uses some kind of client-side script to
    validate the form!

    Hi Rea,
    Per my understanding you want to know some information about using the Visual Studio to do the debugging, right?
    Example, If you want to debug a customized extension for SQL Server Reporting Services(SSRS) in Visual Studio, you can attach the process to ReportingSerivcesService. We need to check the items "Show processes from all users" and "Show
    processes in all sessions" to show the "ReportingSerivcesService. exe" process.
    Additionally, please make sure the customized extension is invoked in the Reporting Services(make sure all configurations is set correctly), otherwise we won't be able to run into the breakpoint. More Details information in this article for your reference:Start
    a debugging session for a Store app in Visual Studio (VB, C#, C++ and XAML)
    You can also add the debugger keyword in the code, see
    Debug JavaScript and jQuery using Visual Studio in Internet Explorer browser
    Similar thread below for your reference:
    https://social.msdn.microsoft.com/Forums/sqlserver/en-us/df9dfaab-59af-4a85-916c-ef9e11e07071/debug-custom-net-assembly-in-context-of-sql-reporting-server-2008?forum=sqlreportingservices
    If you still have any problem, please feel free to ask.
    Regards
    Vicky Liu

  • Sh controller d0 | beg ---Clients output

    Anyone know what the "Dec" column means in the "sh controller d0 | beg ---Clients" output below?
    Asking because the two clients having issues on this AP have incrementing counts on this value.  I assume it has something to do with (de/en)cryption, as all other clients are on an unencrypted SSID.
    Thanks for any feedback,
    --Bruce Johnson
                          RxPkts KBytes Dup Dec Mic   TxPkts  KBytes  Retry RSSI SNR
    0026.bbec.73d1      354     26  244   0   0      232     128    532   92  43
    0015.70a4.3707      375     89    8 291   0       50      18      0   55  41
    0015.70d3.5040     1291    313   43 1076   0      101      37      0   55  40
    0025.0042.f115     4944    273 1305   0   0       81      14    324   84  12
    001f.5bca.d40b    15974    640 6715   0   0       46       5    183   84  12
    0026.bb04.4ee4    12861    867  205   0   0     3022     684   1625   78  20
    001f.5bdc.1a01    21388    767 1302   0   0        6       1      9   76  23
    001f.3b02.2891    11386    695  541   0   0     1493     620    223   71  25
    0023.1219.5545    28703   4074    9   0   0    25935   26861   7384   72  24
    0011.24c6.c421    11418   1649    0   0   0        7       1     10   78  19
    f81e.dfe2.4161     6764    270  144   0   0       22       4      7   64  32
    f81e.dfe2.4129    19812    864 1178   0   0        8       1      6   76  20
    0015.70b0.974c      133      7    0   0   0       42       2      4   57  40
    001f.e12b.8de6    88834   3407 3544   0   0       82      14     86   78  18
    0016.cb00.f8c2    99865   6140 1741   0   0     6654    1119   7148   79  17

    My guess is, based on the controllers client statistics screen, is that "Dec" means "Decrypt Failed."
    Client Statistics
    Bytes Received
    Bytes Sent
    Packets Received
    Packets Sent
    Policy Errors
    RSSI
    SNR
    Sample Time
    Excessive Retries
    Retries
    Success Count
    Fail Count
    Tx Filtered
    Data Retries
    Rts Retries
    Duplicates
    Decrypt Failed
    Mic Errors
    Mic Missing Frames
    Packets Received
    Packets Sent
    -->
    Link Test Results
    Client MAC Address
    AP MAC Address
    Packets Sent/Received by AP
    Packets Received by AP
    -->
    Packets Lost (Total/AP->Client/Client->AP)
    Packets RTT (min/max/avg) (ms)
    RSSI at AP (min/max/avg) (dBm)
    RSSI at Client (min/max/avg) (dBm)
    SNR at AP (min/max/avg) (dB)
    SNR at Client (min/max/avg)(dB)
    Transmit retries at AP (Total/Max)
    Transmit retries at Client (Total/Max)
    Packet rate
    Sent count
    Receive count
    Packet rate(mcs)
    Sent count
    Receive count
    Ping Test Results
    Client MAC Address
    Packets Length
    Packets Sent
    Packets Received
    Local Signal Strength (dBm)
    Local Signal to Noise Ratio (dB)
      Link test in progress .

  • SSID/VLANs for Guest/Staff with 3600 and 2504 Controller

    We are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall.  We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID.  Any pointers to documentation on how to configure?

    in the WLAN configuration, you select what interface you want it to be linked to.
    In the Controller Tab, on the left, go to interfaces.  This is where you create teh interface name, set the VLAN,and the IP address.
    Steve

  • Does Instant Client support client result caching?

    Hi all,
    couldn't find the answer to this question on the ic-FAQ (http://www.oracle.com/technetwork/database/features/oci/ic-faq-094177.html)
    Does Instant Client support client result caching?
    Kind regards, Sander.

    Yes. Like any other OCI feature, Client Result Caching is supported by Instant Client.
    Besides OCI documentation, here is a link to white paper on Client Result Caching and other OCI features: http://www.oracle.com/technetwork/topics/php/whatsnew/building-best-drivers-131920.pdf

Maybe you are looking for