3905 handsets and LLDP

Hi everyone.
I am having an issue with a 3905 handset connecting to a BE3000 running 8.6.4. All of the other handsets I have tried receive their VLAN ID via LLDP and connect to the system without any problem. The 3905, however, will not. It seems that when LLDP is enabled the handset always shows VLAN4095 in its configuration and does not pick up the VLAN ID that is being specified by the switch via LLDP.
I have manually set the Admin VLAN of the handset to 2, but according to the manual this setting will only become active if the phone does not receive any VLAN information from LLDP. With LLDP active on the switch this setting is ignored which shows that the handset is receiving something from the switch but perhaps not interpreting it correctly. If I disable LLDP (or set it to receive only) on the port that the 3905 connects to the admin VLAN comes into effect and the handset connects to the system. If I enable LLDP again the handset will not connect.
All handsets are connected to the same Cisco 300 series small business switch running the latest firmware (at the time of opening this post). The other types of handsets I’ve tried all work correctly with LLDP, but the 3905 must be connected to a port where LLDP is disabled (or set to Rx only) to connect to the system if you wish to specifiy a tagged VLAN ID.
Has anyone else experienced this issue?
Many thanks.

The switch is configured with auto voice VLAN enabled, with a VLAN ID of 2.
Running config is shown below. The 3905 handset is connected on port 4 where LLDP is set to receive only. Any other handset in this port works fine with LLDP set to Tx and Rx.
config-file-header
switch0da7e6
v1.2.5.70 / R750_NIK_1_2_584_002
CLI v1.0
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
spanning-tree priority 4096
vlan database
vlan 2-5,100
exit
voice vlan id 2
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
bonjour interface range vlan 1
ip access-list extended ACL01
permit tcp 192.168.2.249 0.0.0.0 any 192.168.0.252 0.0.7.0 www
deny tcp 192.168.2.0 0.0.0.255 any 192.168.0.252 0.0.7.0 www
permit ip any any
exit
hostname switch0da7e6
management access-list SecureAccess
permit ip-source 192.168.1.0 mask 255.255.255.240
permit ip-source 192.168.2.0 mask 255.255.255.240
permit ip-source 192.168.3.0 mask 255.255.255.240
permit ip-source 10.1.1.0 mask 255.255.255.240
exit
management access-class SecureAccess
passwords aging 0
ip ssh server
interface vlan 1
ip address 192.168.1.252 255.255.255.0
no ip address dhcp
interface vlan 2
name BE3000
ip address 192.168.2.252 255.255.255.0
interface vlan 3
name UC320
ip address 192.168.3.252 255.255.255.0
interface vlan 4
name UC540BRI
ip address 192.168.4.252 255.255.255.0
interface vlan 5
name UC540FXO
ip address 192.168.5.252 255.255.255.0
interface vlan 100
name UC320Phones
ip address 10.1.1.252 255.255.255.0
interface gigabitethernet2
switchport trunk native vlan 2
interface gigabitethernet3
switchport trunk allowed vlan add 100
switchport trunk native vlan 3
no macro auto smartport
interface gigabitethernet4
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport trunk allowed vlan add 2
no lldp transmit
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type ip_phone_desktop
interface gigabitethernet5
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport trunk allowed vlan add 2
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type ip_phone_desktop
interface gigabitethernet6
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport trunk allowed vlan add 2
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type ip_phone_desktop
interface gigabitethernet11
switchport trunk native vlan 100
no cdp enable
no macro auto smartport
interface gigabitethernet12
switchport trunk native vlan 100
no cdp enable
no macro auto smartport
interface gigabitethernet16
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport trunk allowed vlan add 2
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type ip_phone_desktop
interface gigabitethernet17
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport trunk allowed vlan add 2
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type ip_phone_desktop
interface gigabitethernet23
switchport trunk native vlan 100
no cdp enable
no macro auto smartport
interface gigabitethernet24
switchport trunk native vlan 100
no cdp enable
no macro auto smartport
interface gigabitethernet27
channel-group 1 mode auto
interface gigabitethernet28
channel-group 1 mode auto
interface Port-channel1
speed 1000

Similar Messages

Serious problem with blackberry 9300 Curve handset and denial from BB to replace the same, under warranty.

Dear Blackberry Authorities,
It is really a horrible experience with the handset of blackberry for me. I have purchased blackberry Curve handset 9300 on 22nd April from a "Phone Store”, Shop No.78,79,community centre, New friends colony, New Delhi, The Invoice No. is 319,The details of the handset are as follows:
Handset: Blackberry Curve 9300 1256-India Qwerty-Pink
Name: Blackberry 9300: ETA-716/2010/WRLO
Model: RDA71UW
It has been more than just three months ,when i purchased this handset ,It worked fine for about only fifty days from the date of purchase and from the second month ,to my shock, serious problem started in the handset and some time it was getting hanged ,sometime some keys in the keypad did not work ,some time it was getting hanged the moment I receive incoming call., sometime sms sending problem, some time some other problem ..Every time I used to switch off the phone and start again, then it used to work but after some days again there were some other problem occurring in the handset.
The phone was not getting connected to PC from the starting, and i have tried so many times but i fail to get success.
Many a times when I used t send sms the entire alphabet typed on sms has gone separately as a single alphabet in a particular sms to the recipient, causing embarrassment for me in my organization. I would blame the black berry for this embarrassment as this has caused due to faulty phone they have sold me,
I am service class person and i get occupied with my work at office in the day hours and doesn’t have time to go to the service centre of blackberry every time the problem occurs, as there are only one service centre available in Delhi at Lajpat Nagar.The service centre is about 20 Kilometers away from the area my office is situated, I managed to keep the phone running by switching off and switching on after one or two minutes, every time the problem occurs but in the first week of last month ,when the problem started continuing after switching off and switching on also ,I was bound to go to service centre at noida since it is close to my place (about 14 Km) in comparison of Lajpat nagar at new delhi,the service engineer at blackberry service centre saw my phone and said there is some software problem which can be rectified by reinstalling the software, and there are some hardware problem also (some keys on the keypad is not et. all working) ,for which i have to surrender my phone to them and they will send it to the Blackberry Office (they did not give address) and it would take 15 days at least ,thus since I had no back up phone and my each and every contact no. was there in phone it was difficult for me to give them handset at that time ,so I requested them to rectify the software problem by re installing the same.
I asked the service manager to get the backup of all the data and contact no saved into the phone, but they refused to do so and they asked me to go to some other shop nearby to get the data backup, I went to that shop and they asked 250 Rupees for data backup of my phone. I was bound to say yes to them for the amount the charge for backup .I gave them my handset and after 20-30 minutes they came back to me by saying, we cannot store your data backup as it is not connecting to PC. It was a highly disappointing reply for me.
Then i again went to your service centre and written down some important contact no.(the number which was stored on phone book) on piece of paper and taken out my SD card ,and gave them handset for re installing the same.
They gave me my handset after one and half hour and said" now it would work fine except hardware problem.".I came back and to my utter shock again after two three days handset was into its old condition ,then also I tried to manage with handset and when i could spare sometime I went to your service centre again on 24th July at Noida,
they took the phone and said it would take 12-15 days to return the handset after rectifying the problem,when i requested them to change the handset with a new handset which is at least in good working condition , they clarified that if the hardware problem is not manageable or repairable ,i would get new handset had no option except to give them handset for rectifying the problem.
Now,It is the time for a biggest shock from blackberry people-Today on 3rd August ,i have received a call from noida blackberry service centre to inform me that my handset cannot get repaired under standard warranty conditions of blackberry as there are some moisture into the phone and there is no warranty if there is a moisture inside the phone.
Thus now i wish to inform all the concerned ,Blackberry/Research in Motion ,managers/authorities ,that i have explained above ,all the things ,happened to me in last three months of my purchase of handset, in detail ,so i would again request to Blackberry/Research in Motion ,managers/authorities, to rectify the problem of my handset or change the entire handset so that I can use the same peacefully and should not roam around the service center of blackberry.
Giving this lame excuse that "there is a moisture inside the handset and thus it can’t get repaired or changed under warranty " is a clear case of cheating and harassing the customer, I have bought the handset to use it for my communication purpose not to roam around the blackberry service center nor to put water or moisture inside the handset and play with the handset and fight with all of you.
If there were some moisture inside the handset then that should have been seen by the noida service centre people also during my First visit itself by them and they would have refused taking the handset for repair. They did not refuse but accepted handset and reinstalled software also, If there was some moisture that would have been seen by them that time only.
In my second visit also the took my phone and seen the inside condition also of handset in front of me ,they did not see any moisture, that time also ,and now after 10 odd days ,there are some moisture inside the phone??????.
I have no idea how blackberry keeps its handset ,which has come to them for repairing ,but if there is any trace of moisture into my handset ,that would have come into the handset ,during these 10 days only when phone was with blackberry authorized service engineers for repair purpose. What I know is that My Blackberry handset is under warranty and it is not working properly thus it should be replaced by Blackberry.
On the keypad if some key are not working that is a hardware problem which was there in the handset and it has no connection with the moisture.
If this is the way blackberry is treating its customer, i would say it is harassing its customer, and does not want to rectify the problem .in this case, I would have no option left except to go to the consumer court in Indian judiciary system. And moreover i would inform my and other friends, organizational employee also not to use services/or buy blackberry handset if this is the way BB is treating its customer.
I would request all the concerned persons/managers/authorities of Blackberry/Research in Motion, take action into my case urgently and rectify the core problem into my handset instead of giving lame excuses, and change the faulty handset of mine with a new properly working handset under warranty condition.
Best Regards
Asim
Edit: Personal information removed. At no time should you provide any personal information to any other community member. Please review the Community Terms & Conditions and Support Community Guidelines for additional information.

dubem747 wrote:
It looks like your phone has a some virus, use your computer to scan and remove it.
not possible for it to have a virus and a PC would not know how to scan the OS as its protected
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

On my list of calls made/received some of them have an icon which is a phone handset and something else. Can you tell me what this is and where to I D icons?

On my list of incoming/outgoing phone calls some of them have an icon beside the name which is a telephone handset and something else I don't recognize. Can anyone tell me what it means and where to find a list of icon explanations? Thanks.

You're probably talking about the handset with an arrow pointing up and to the right. That indicates an outgoing call.

"Unable to start application" on Handset and Simulator

hey there,
i'm having some problems getting any flash lite content to
run. i get a message that reads "unable to start application"
whenever i launch my apps on the handset and in the simulator.
i installed flash pro 8 (trial) on my system, installed the
flash lite 2 update, installed the flash lite 2.1 post processor
plug in and publish the files fine. i went to qualcomm's
developer's extranet and downloaded the flash lite 2.1 for brew
devices module. i also loaded the flashlitemod module and the
brewsaplayer module.
i even tried running the included example from the qualcomm
extranet (called "usingbrewsaplayer"). anybody else experience this
or know what could possibly be wrong? any help would be
appreciated!
thanks

You need to install the BREW SDK 3.1.x first, restart your
system and then install the FL publisher for BREW. During the
install process for the FL publisher for BREW it will check to see
if you have the BREW SDK 3.1.x installed - if it does then it will
copy over the necessary DLL files to allow you to preview your FL
apps (MOD/MIF) in the BREW simulator.
So uninstall the FL publisher for BREW, restart your system.
reinstall the FL publisher for BREW, restart and then test your
MOD/MIF files in the simulator.
For example if your app is called "ball" and the FL publisher
for BREW published the DLL, MOD and MIF files you will need to do
the following:
1) copy the "ball.mif" file to C:\Program Files\BREW
3.1.4\sdk\examples
2) create a folder called "ball" here C:\Program Files\BREW
3.1.4\sdk\examples, so you should have "C:\Program Files\BREW
3.1.4\sdk\examples\ball"
3) copy the "ball.dll" file to C:\Program Files\BREW
3.1.4\sdk\examples\ball
Launch the BREW simulator and you should see your application
as a broken icon show up in the menu structure and the applet name
you defined will appear as well. If you select the app (press OK
button on phone) your app should work in the simulator.
Let us know if this works.

How to generate reports of registered IP handsets and their corresponding extension on call manager 4.2.3

Hi
how to generate reports of registered IP handsets and their corresponding extension on call manager 4.2.3
I checked the route plan report and the generate report function on the BAT.. however it doesnt has the feature to generate only the registered IP phone with its coresponding extension
Thanks
Kind regards
Rachel

Call manager provides the called party with the extension or directory number of the calling party on a display. You can use the Calling Line ID Presentation field in the Gateway Configuration window to control whether the CLID displays for all outgoing calls on the gateway.Refer URL
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a008070e48b.html#wp1051056

Cius and Docking Station-handset and speaker not working

Hi
I have a cius registred on CUCM 7.1.5 20000 -6 with device pack 7.1.5.34074-1, the phone can make and receive calls but i can't hear anything in the handsets (and speaker), even not the dial tone.
Cius is connected to a UC500 (just to have PoE, i don't have a PoE switch) to power docking station.

You need the Cius power brick if you don't have PoE+

Interrupted my Restore iPhone 4 on my new handset and now I can't do it?

I smashed my iPhone 4 a couple of weeks ago and got a brand new handset today in the Apple Store. The genius guy restored my contacts onto it so when i got home I connected it to iTunes, worked through the "get started" menu and opted for restore this iPhone from iCloud (instead of restore as a new phone). It was all going perfectly and the phone was 10mins off being fully restored until my laptop ran out of battery and switched itself off! Now when i connect the phone to iTunes there is no get started menu and the only option i have for restore is for factory settings!! Is there any way I can get back to restoring? I don't want to lose my messages/photos/notes/emails or music!!! please help

It won't let me change it. I tap on the phone number and nothing happens.

Cisco SG300 and LLDP with Yealink Phones.

I am currently trying to setup a Cisco SG300 switch with a hosted VoIP solution using the SG300's at the customer's premise. The Yealink phones I am not able to get them to pull an IP address and believe the problem is related to LLDP. We also use Polycom phones and they work just fine. Here is the configuration that I am currently using ( I have tried several different configurations and none of them work with the Yealinks. Any help would be greatly appreciated.
DLC#show run
config-file-header
DLC
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
vlan database
vlan 2,88
exit
voice vlan id 88
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname DLC
interface vlan 2
name Data
interface vlan 88
name FlexVoice
interface gigabitethernet1
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet2
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet3
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet4
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet5
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet6
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet7
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet8
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet9
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet10
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet11
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet12
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet13
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet14
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet15
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet16
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet17
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet18
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet19
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet20
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet21
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet22
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet23
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet24
switchport trunk allowed vlan add 88
switchport trunk native vlan 2
no macro auto smartport
interface gigabitethernet27
switchport mode access
switchport access untagged vlan 2
no macro auto smartport
interface gigabitethernet28
switchport mode access
switchport access untagged vlan 88
no macro auto smartport
exit
DLC#

Here is the latest configuration that I tried, Polycom phone worked, Yealink didn't.
co-test#show run
config-file-header
co-test
v1.4.0.88 / R800_NIK_1_4_194_194
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
vlan database
vlan 2,88,881
exit
voice vlan id 88
voice vlan state oui-enabled
voice vlan cos 6 remark
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 0004f2 Polycom
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 001565 Yealink
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname co-test
interface vlan 2
name data
interface vlan 88
name flexvoice
ip address 172.16.88.2 255.255.255.0
no ip address dhcp
interface gigabitethernet1
voice vlan enable
interface gigabitethernet2
voice vlan enable
interface gigabitethernet3
voice vlan enable
interface gigabitethernet4
voice vlan enable
interface gigabitethernet5
voice vlan enable
interface gigabitethernet6
voice vlan enable
interface gigabitethernet7
voice vlan enable
interface gigabitethernet8
voice vlan enable
interface gigabitethernet9
voice vlan enable
interface gigabitethernet10
voice vlan enable
interface gigabitethernet11
voice vlan enable
interface gigabitethernet12
voice vlan enable
interface gigabitethernet13
voice vlan enable
interface gigabitethernet14
voice vlan enable
interface gigabitethernet15
voice vlan enable
interface gigabitethernet16
voice vlan enable
interface gigabitethernet17
voice vlan enable
interface gigabitethernet18
voice vlan enable
interface gigabitethernet19
voice vlan enable
interface gigabitethernet20
voice vlan enable
interface gigabitethernet21
voice vlan enable
interface gigabitethernet22
voice vlan enable
interface gigabitethernet23
voice vlan enable
interface gigabitethernet24
voice vlan enable
interface gigabitethernet27
switchport mode access
switchport access vlan 2
no macro auto smartport
interface gigabitethernet28
switchport mode access
switchport access vlan 88
no macro auto smartport
exit
co-test#

LMS 4.2 User Tracking for Avaya IP Handsets and Connected Devices

I manage an environment that makes extensive use of Avaya IP phones and it's frustrating that this seems to limit the usefulness of the User Tracking application within LMS.
We configure the switch (2960) ports connected to the handsets as dot1q trunks with the associated PC being connected to the switch built into the phone.
Having done some forum research it seems that UT only adds an entry for a device connected on a trunk port if it is a Cisco IP phone, not anything else. This is frustrating as it eliminates a large part of our network from being recorded in UT and is doubley frustrating since the PC connected to the switch on the phone also isn't recorded.
Is there any way to get around this problem that anybody is aware of? Thanks

As long as you have a supported Cisco Layer 3 device in your LMS-management domain, you should be able to correlate the IP-MAC addresses in User Tracking (UT).
UT support is not specifically listed for the ASA firewall - I'm not sure it will support that feature if it is the users' gateway.
Useful links:
UT explanation from the LMS Admin Guide
Supported devices listing
Hope this helps.

Dualphone 3088.1 Handset and Receiver 3088.2

Dear All,
I just bought an extra handset model 3088 to replace to current one that I have.
I bought it trough Amazon, sold by Chat and Vision, and received it ok.
When I tried to register, it never registered, and then after some googling I found out that there's not only one model of 3088, but several ones like 3088.1, 3088.2...
So... my base station is 3088.2 and the extra handset that I bought I found out that is a 3088.1... It seems that they don't communicate with each other.
The problem, is that that Company and Amazon didn't say nothing about models in anywhere of product description or any warnings to consumers... and now I have an extra headset that I can't register.
Would like to have your technical support about this situation, and your suggestions.

I would think that since they carry the same model number the version number should not have any affect on a successful registration of the handset. As far as I can tell there is not much that has to be done to register a handset, so if it does not work, then the handset may be defective.
The obvious:
Make sure the base station is on and the reset button has been pressed putting it in a mode ready to register handsets.
The key things I would try if it fails:
1. The battery from on the other working handsets, in case there is an issue with the one you received.
2. Deregistering all the other phones, and try to re-register that singular phone.
3. Resetting the base station and inserting the new phone into the cradle to register it.
You can alway pose your question about versions to dualphone support:
http://dualphone.net/en/information/online_support/
You can contact Chat and Vision/Amazon about the same thing or inquire about returns or replacement:
http://ca.chatandvision.com/display/ws_view?page=ws_contact

Any way to disable the bluetooth handset and use enable streaming audio only?

I don't use bluetooth in my car to make or receive phone calls and only use it to stream Pandora. On my previous BBs I was able to disable the handset function and just use streaming audio, but I'm not finding any similar options on the Z10. Does anyone know of a way to do this? Right now I'm just powering off my stereo when I receive a call, but that is not a great solution. Thanks for any feedback.
Solved!
Go to Solution.

Hello rangerdanger and welcome to the BlackBerry Support Community Forums.
Thanks for your question regarding Bluetooth.
The BlackBerry Z10 does not have the option to edit what services are allowed with a Bluetooth connection.
Depending on your vehicle, you may have to access your Bluetooth set up or settings within your car's dash to control what features are enabled with Bluetooth.
If you are unsure how to access these settings, contact your dealership or consult your owners manual.
Cheers!
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Buying a handset and use it in Europe with a different sim card

Hi, would it work if I buy a blackberry handset in the US and ship it to a friend in Belgium who will install a local sim card?

yes if you get an AT&T device that is unlocked it should work fine.
Tmobile ones will not get 3g as their bands are different.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Synergy 4500 using 2 handsets and bases

I have bought 2 seperate Synegy 4500 bases/handsets.How can I code them together to be able to use 1 hanset upstairs and the other downstairs ?

As they come pre-registered to their respective bases, I guess you'll need to de-register one of them, re-register it to the other base, then use its original base as a charger only.
If that doesn't work, try the helpline 0870 605 8047.
You can click the white star next to this message if you think it was helpful.

Inspire 1500-Nameing Handsets and Using Intercom

Hi All
I have just set up a new Inspire 1500 with 4 x handsets. I have named each of the handsets Bedroom, Study, Hall, Kitchen and am now playing with the intercom feature.
When I select Intercom I expected/hoped that I would get the list of re-named handsets but this is not the case, I still get a scroll down menu of Handset 1, 2, 3, 4. Is there a way of updating the Intercom list to the new handset names Bedroom, Study, Hall, Kitchen? I have tried to re-register the hand sets with the Base Station and this makes no difference.
Thanks
jhdeano

The only problem I can see with associating an aspire handset with the 6500 base station is that it "may'" not filter out the barred type of calls. It may be worth trying. If it does work perhaps you could come back to the forum and let us know. I am sure that the barring is done on the base station.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

Recent Nokia handsets and video focus

I think this issue deserves a dedicated topic. As highlighted on All About Symbian, a good chunk of Nokia's handsets last year focus at infinity when taking video, meaning the camera's useless for subjects within a few metres, and this has never been addressed in software. The E72, N97 and N97 Mini continue this trend, so out of all the autofocus handsets released since, only the N86 is actually using a proper focus distance.
http://www.allaboutsymbian.com/features/item/Camera_Nitty_Gritty-Extra_Video_focus.php
A good example is here:
http://www.youtube.com/watch?v=Xu-SKb7Qqic
Although the camera is capturing plenty of detail, it is capturing detail of an out-of-focus image, so you can't (for example) read any text on the video.
This is probably for posterity because I doubt that Nokia's going to address this unless they change cameras again.
Message Edited by sockatume on 06-Jan-2010 11:40 AM
Help I'm trapped in a sig factory.

The three of the Nseries handsets it lists (N85, N79, and N97) supposedly shoot VGA at 30fps, not that you could tell from looking at the videos they produce! It's a shame really, the hardware's there but the software needs just the tiniest fix to make the camera work.
I think the 5800 works the same way as the rest, infinity focus.
Help I'm trapped in a sig factory.

3905 handsets and LLDP

Similar Messages

Maybe you are looking for