4506 SMARTnet (Sup + Module) question

I like to ask how SMARTnet works for especially moduled switch. For example, I have 4506 switch ( Processor board ID SPE163200V3 ). According to recent renewed SMARTnet, it covered SPE163200V3. I like to make sure Processor board ID covers what components in switches because switch has one Sup and 3 modules like below.
4506e_HQ_core#sh module
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1     6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E     CAT1639L0LJ
2    48 1000BaseX SFP                          WS-X4448-GB-SFP    JAE16320BMR
3    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE16370A7O
4    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE14520GWF

Yes, it will cover all the modules you have in the chassis.
HTH

Similar Messages

How many VRF-Lite Routing Instances can a 6509-E with a 720-Sup module run?

I know that in a 4500 style switch it supports a maximum of 64 VRF-lite routing instances. However what is the maximum amount of VRF-Lite routing instances can a 6509-E switch support with a Sup-720 sup module?

Sup 720 supports 1024 VRF Lites
see table-1 in this link:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/product_data_sheet09186a0080159856.html
HTH

SUPER IMPORTANT QUESTION (really!!) Zen Mi

<SPAN>PACKAGE CONTENTS
Zen Micro Player</LI>
Rechargeable Li-Ion Battery </LI>
High Fidelity Earphones</LI>
USB 2.0 Cable</LI>
Creative Media Source</LI>
Installation CD</LI>
Quick Start Guide</LI>
Limited edition Zen Micro 5GB comes bundled with these additional accessories*:
Power Adaptor</LI>
Belt Clip & Stand</LI>
Pouch</LI>
*While Stocks Last
I Thought all ZM5GB came with the belt clip/stand/pouch...so only if u buy on line u get it's?

A "super important question" would be something like, "is there a god?" or "what are my chances of surviving this operation?" or, maybe, "my Zen Micro is showing a message saying 'will self-destruct in fi've minutes unless technician code is entered' -- does anyone know the technician code?" (no, no one has ever asked that question).
Yours doesn't qualify.
The answer is that, at the moment, all 5gb Micros as far as I know come with these accessories, all 4gb and 6gb don't, but READ THE PACKAGE CONTENTS before buying to make sure.Message Edited by tganani on 04-09-2005 05:59 PM

Order the FAQ module questions

I am trying to order the FAQ module questions in Business Catalyst.
It puts them in alphabetical order by default so I numbered them. But once it gets to 10 it obviously goes out of order.
And the client does not want to put a letter in front. ie A, B, C
Any ideas on how to acheive this?
Thanks in advance.

Try leaving numerical gaps in your weighting scheme so you have future flexibility.
For example, I like to use the weightings of 1000, 900, 800, 700 and so on.
Then I have a LOT of wiggle room to add new information and sort my information the way I like.
Tricia

Mgnt IP address on 4506 w/ sup V

Hello all, I have two questions. The new 4506 SUP V engines don't have the good old SCO interface that I'm used to. So, since it's running an IOS now instead of the old CATos, I figured I'l create a new vlan and then make it the management IP address by using the 'MANAGEMENT' command (like in the old 2900's). Well, that didn't work either, so my question is...on what int. do I configure the mgnt. IP address?
-thank you....

Hi,
Just think of Cat4506 with SupV like being a router: Any L3 interface can be used for mgmt. This can be either physical with "no switchport" configured and IP address assigned or logical e.g. interface vlan (and IP address assigned).
Best regards,
Antonin

Training and Event module questions.

Hi .
I have some questions regarding Training and Event Management module.
1. IS there a way to configure a custom attendee type for this module ?
2. If no is there a way to rename a existing attendee type. I have a requirement to create a group of attendees type of External Person. I know i can use Company attendee type for grouping external person. But i need to change this Company to Group for displaying purposes. I know i can change the Company via T7778O table but won't it lead to bad consequences ?
3. Is there a way to hide tabstrips on PVOO screen ? i have a requirement to keep only Company tabstrip others are not relevant for my scenario.
That's all for now.
Thanks in advance.
Edited by: kernel.panic on Dec 22, 2010 8:47 AM

Hi,
thanks this one is ok, the one which I can not find is the info message for when the maximum capacity of the attendee list is reached:
'Optimum capacity reached, only essential or wait list bookings possible' This one I want to change into a warning message.
br,
Ovidiu
And I have a new question as well
In the Attendee List layout is it possible to add columns which are not in the column set from customizing e.g. Personnel subarea,
Employee subgroup, Employee group etc?
Thanks
br,
Ovidiu
Edited by: Ovidiu Moldovan on Apr 20, 2010 3:51 PM

IPad - SUP connection questions

The import works perfectly on device but I'd like to have more control on that. here are different questions I'm asking myself concerning that :
1) I'd like to check if the connectivity is ok before deleting the local DB ?
When using the code above the locale db is deleted before launching SUPMessageClient start. It is recommended to do that in the documentation BUT, if the connection does not succeed, the locale db is empty and the iPAd app can not be used anymore. IS there a way to check connectivity before launching the sync process ?
2) On the other hand, I've got a method creating new elements and I'm calling submitPending, but nothing happens in terms of update to the server. Should I do a subscribe to the package each time I want to interact with the remote SAP server ?

Hi again,
yes, you can search for records in the local (iPad) database. Contrary to Apple's core data you don't have to use predictives but you have to define the query for a database search on the SUP. When modelling the attributes of your MBO in the Unwired Workspace, you can define the syntax of the query on right-most tabsheet (named "Object Queries"). The "findAll" and "findByPrimaryKey" query are the 2 default ones.
For instance, if you have a MBO called "TimeRecord", a query could look like:
SELECT x.* FROM TimeRecord x
WHERE x.WBS_ELEMENT = :wbsNumber
AND x.WORKDATE = :Workdate
where you have to define the parameters wbsNumber and Workdate which are mapped to the MBO-fields WBS_ELEMENT and WORKDATE respectively. The name of the query could be LookForTimerec
In xCode you can now simply type:
objTimeRecordList* timerecordlist = [objTimeRecord LookForTimerec:wbsElement withWorkdate:workDate];
where wbsElement and workDate are Objective-C variables (which you have to define).
objTimerecord is the class-Name of the MBO and objTimeRecordList is the SUPObjectList of Timerecords: both objects will be generated by SUP and are imported with the source code into your xCode project.
During runtime, the variables wbsElement and workDate will be mapped onto the query-parameters wbsNumber and Workdate.
Best regards
Herwig

Module Question.

Hi all,
My scenario is File->XI->R3
Can I validate file information in a Sender Adapter Custom Module and if the validation fails then cancel the input so Integration Engine never gets the corresponding message? My question is how to cancel the procesing of the message in the adapter module?
Thanks in advance,
Diego.

Chandu,
my problem is that I want to validate data of an input file, so if the file doesn't contain certain fields, then it doesn't go to the XI Engine. (It's discarded before that.)
So i thought to build a module for the sender adapter that do this validation, but I don't know how to discard the message at modules chain.
I hope you could understand my english.
Regards,
Diego.

Cat-4506 with Sup II+ won't load new IOS

I'm trying to upgrade the IOS on my 4506 SUP II+ (WS-X4013+) to 12.2(31)SG from 12.2(25)EWA5.
Here are the boot commands and what is in bootflash: and the error during boot:
boot system flash slot0:cat4500-ipbasek9-mz.122-31.SG.bin
boot system flash slot0:cat4000-i9k91s-mz.122-25.EWA5.bin
Configuration register is 0x2102
ROC-SW4506-A#sh bootflash:
-#- ED ----type---- --crc--- -seek-- nlen -length- ---------date/time--------- name
1 .. image 8B6309F2 CACAA0 33 13027872 Dec 22 2005 04:24:19 -08:00 cat4000-i9k91s-mz.122-25.EWA5.bin
2 .. image 3D38E47C 1824E28 33 12026632 Jun 2 2006 11:06:21 -07:00 cat4500-ipbasek9-mz.122-31.SG.bin
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Current BOOT file is --- slot0:cat4500-ipbasek9-mz.122-31.SG.bin
boot: can not load "slot0:cat4500-ipbasek9-mz.122-31.SG.bin"
The switch will automatically reboot now...
rommon 1 >
It eventually booted to the older IOS. Is this not a good IOS for this switch?

have you tried putting
boot system bootflash:cat4500-ipbasek0-mz.122-31.SG.bin
taking out the slot0:.
This how I have my 4507 and 4503 configured.
http://www.cisco.com/en/US/products/hw/switches/ps663/products_configuration_example09186a00801461ef.shtml

5B32 module question

This is more of an equipment question, but I figure that thisis as good a
place as any to ask.
I've got about six 5B32 modules, and I need three. The problem is that
four of the resistors that go with them are bad. I had as bad board,
which I think might have screwed up the resistors. The resistors that
Ihave that are good are reading about 20 Ohms of resistance, and the bad
ones are 6 Ohms, 80 Ohms, 1.5 megaOhms, and 2.2 megaOhms.
I have tried to buy some resistors from National Instruments and Analog
Devices, but they don't know what they are (the part number doesn't come
up at all). I hate to keep buying entire 5B32 modules when I only need
the resistor. So, can I just go buy a 20 Ohm resistor at Radio Shack, and
plug it i
n, or is this thing that comes with it something special?
Thanks in advance,
Harry
"Little Joe for the Big Heisman, '99"

Absolutely - go down to Radio Shack and purchase some - The max current
sould be 20 ma (since the 5B32 is a 4 - 20 ma current input module) so P =
I^2 R , P = (.02)^2 * 20 = .008 Watts therefore a 1/4 or 1/2 watt resistor
should be more than adequate.
A 1/2 watt resistor has leads that would probably plug into the 5B01
backplane nicely.
Good Luck
Harry King wrote in message <7q65an$[email protected]>...
>This is more of an equipment question, but I figure that thisis as good a
>place as any to ask.
>
>I've got about six 5B32 modules, and I need three. The problem is that
So, can I just go buy a 20 Ohm resistor at Radio Shack, and
>plug it in, or is this thing that comes with it something special?
>
>Thanks in advance,
>Harry
>
>--
>"Little Joe for the Big Heis
man, '99"

Quick Module Question

I have a link bar component that is linked to a ViewStack
component, which has four stacks. I want to use modules in the last
three stacks and my question is: Will the modules load when the
user clicks on that particular stack, or will all of them be loaded
even if the currentView property is set to 0?

I think that that has to do with the "creation policy" and
can be set either way.

STREAM module question

Hi all,
I am newbe in STREAM module development and this question might be a concept error. If so, please could you give me some clues?
I would like to use the "libc" funcion "getpwuid()" in a kernel STREAM module.
I have Solaris 7 64-bit kernel.
�Can I do it? I have read that for 64-bit kernels, only dynamic libraries are available. Therefore in order ot use libc functions I would have to link dynamically the module relocatable object with the libc library in sparcv9. I have tried to link the kernel STREAM module with libc.so.1 (in /usr/lib/sparcv9) with no success so far. Everytime I trie to load the module it complains with the message: unknown symbol "getpwuid".
If it is not possible, why? . Is it not possible to use libc functions such us: memcpy() etc..from the kernel context?
Looking forward to hearing from you.
Best Regards

You cannot use user space libraries from within a kernel module. What exactly are you trying to
do? What do you need password information for
down in the kernel?
Maybe ddi_get_cred() will help?
Some functions like memcopy have kernel space equivalents (bcopy)....
dan

Array Module Question

Hi,
I am currently working on designing phase for an Array Module. We are planning to track the Array information and store it's content to database. Currently I am finalizing the data model and I have following question.
--We need to track the Geneology of the Sample through out the whole system (Especially the results of Transfers). Is it better to have all that relationship in one flat table with columns for location (like PlateWell, GelLane..) and columns for Content (Column like . LocationType LocationId ContentType ContentId) or is it better to store all the content of location as a ArrayType? Or is there any other option available in the Market?
In the first case database rows for that table will increate very very fast plus to find out the geneology of the location in Array , I have to use Connect By Prior which will take good amount of time(Is there any other option available?). I dont have much idea about second option but I think retrieval individual content is going to be a problem.
Any help is really appreciated.
Thanks in Advance
Raj

Made a complete example:
String searchKey = "Juice";
TreeMap tm = new TreeMap();
tm.put("soda", "coke");
tm.put("Juice", "orange");
tm.put("SODA", "7-up");
Set set = tm.entrySet();
Iterator iterator = set.iterator();
while( iterator.hasNext() ) {
Map.Entry entry = (Map.Entry)iterator.next();
if(entry.getKey().equals(searchKey)){
System.out.println("searchKey '"+searchKey+"' value is: "+entry.getValue());
What do you think? Anything obvious that can be improved?

NM-16AM module question in my cisco 3660

hi,
I have 3 of these modules.
with 1 module, when I configure a line and I connect to the line I get only a black screen.
when I do the exact same thing with another module, (configure a line on the 2nd module) it works fine.
my question is, how can I know if a module is broken or not functional. can this happen?
any advice on how to find out if a module is broken or if I single modem in the module is dead.
thank you.
also when I use debug modem and I call a modem that works fine I get this
11w6d: Modem 5/14 Mcom: in modem state 'Dialing/Answering'
11w6d: Modem 5/14 Mcom: in modem state 'Incoming ring'
11w6d: Modem 5/14 Mcom: in modem state 'Waiting for Carrier'
but when I don't get this I know in advance that it's not going to work and that I'll get just a black screen.
any advice please?
thank you.

To identify a functional module , we need to look at the front panel LED of 3660 router. If READY 0, 1, 2, 3 is blinking green it indicates,it indicates the functional module is installed in the slot.If this LED is OFF, it indicates the slot is empty or the module is not functional. For more info on 3660 MAR router, refer the following Link.
http://www.cisco.com/en/US/products/hw/routers/ps274/prod_module_configuration_guide09186a00800d9e97.html

Robotic module Question

Hi all
i have some question about the robotic module.
i already have a DH table for my robto arm.
Now i am trying to input this DH parameters into Labview.
I saw the example of inverse kinematis for puma 560.
Also,I find that the "create PUMA 560 Modified.Vi" can let user to input their only DH parameters.
But
What is the Twist in Labview? angle about previous Z, from old X to new X.
What is the Length in Labview? is it represent thelength of the common normal (r).
What is the Offset in Labview?offset along previousZ to the common normal.
What is the Joint Corrdinate Offseti? in Labview?offset along previousZ to the common normal.
When i modify the DH paramters into "set kinematic parameter.vi",there show a error about -310040.
Anyone can indicate which part i get worg?
Thank you so much
Tim
Attachments:
Inverse Kinematics for Puma 560 org Test.vi ‏34 KB
Test_PUM_560_tim.vi ‏32 KB
myrobotarm.jpg ‏98 KB

Hi Tim,
Thanks for your question. Are you attempting to modify the "create PUMA 560 Modified.vi" that you mentioned using your DH parameters, or are you modifying the "Test_PUM_560_tim.vi" example VI that you attached? The "Inverse Kinematics for PUMA 560 org Test.vi calls the "Test_PUM_560_tim.vi" so if you are using this example as a model, you would have to input your parameters (Length, Twist, Offset which you mentioned) into that VI.
The particular error you are getting (-310040) corresponds to the following error message: "LabVIEW cannot converge to a solution in the number of steps you specified. Make sure that the serial arm can achieve the transform you desire." This could be due to the fact that the current constraints are over defined.
Here is a link to the Robotic Help Manual:
http://zone.ni.com/reference/en-XX/help/372983D-01/
If you would like to give me some more information about your application, I would be happy to help further. Which version of LabVIEW are you using, and which version of the Robotics Module are you working with?
Good luck!
R. Brill
Applications Engineer
National Instruments

4506 SMARTnet (Sup + Module) question

Similar Messages

Maybe you are looking for