4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN

Question

Hi to all.
Follow is the partial configuration of my CME.
It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.
On each port of the 4FXS DID card happens the following:
If I enable direct-inward-dial
    I can receive calls from PSTN.
     Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.
If I disable direct-inward-dial
    I cannot receive directly calls form PSTN.
          Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.
     Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.
I have half the configuration working.
Where am I wrong?
I really appreciate your help.
Thanks to all.
Giorgio.
CME#sh ver
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
CME uptime is 2 days, 15 hours, 49 minutes
System returned to ROM by power-on
System restarted at 18:54:45 CDT Fri Aug 2 2013
System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FTX1120A08L
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
16 terminal lines
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1948656K bytes of USB Flash usbflash0 (Read/Write)
497448K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CME#sh telephony-service
CONFIG (Version=7.1)
=====================
Version 7.1
Cisco Unified Communications Manager Express
isdn switch-type basic-net3
voice translation-rule 1
rule 1 /^2929091\(..\)/ /\1/
rule 2 /^2929091\(.\)/ /\1/
rule 3 /^02929091\(..\)/ /\1/
rule 4 /^02929091\(.\)/ /\1/
voice translation-rule 2
rule 2 /\(.*\)/ /02929091\1/
voice translation-rule 10
rule 1 /\(^......$\)/ /0\1/ type national national plan isdn isdn
rule 8 /\(^......$\)/ /00\1/ type international international plan isdn isdn
voice translation-profile PSTN-IN
translate calling 10
translate called 1
voice translation-profile PSTN-OUT
translate calling 2
interface BRI0/0/0
description Isdn channels 1 & 2
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/0/1
description Isdn channels 3 & 4
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/0
description Isdn channels 5 & 6
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
description not used
no ip address
shutdown
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
voice-port 0/0/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 1 & 2
voice-port 0/0/1
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 3 & 4
voice-port 0/1/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 5 & 6
voice-port 0/1/1
description Disponibile
voice-port 0/2/0
input gain 14
connection plar 83
description Interphone 40
station-id name Citofono
station-id number 40
caller-id enable
voice-port 0/2/1
cptone IT
description Ced 35
station-id name CED
station-id number 35
caller-id enable
voice-port 0/2/2
cptone IT
description FAX_1 50
station-id name FAX_1
station-id number 50
caller-id enable
voice-port 0/2/3
cptone IT
description FAX_2 60
station-id name FAX_1
station-id number 60
caller-id enable
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
answer-address 35
destination-pattern 35$
incoming called-number 35
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
incoming called-number 40
no digit-strip
direct-inward-dial
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
incoming called-number 50
no digit-strip
direct-inward-dial
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
incoming called-number 60
no digit-strip
direct-inward-dial
port 0/2/3
CME#

Answer 1

Hi Paolo.
Sorry for the delay. I was on holiday.
I would like to keep separate incoming calls from outgoing calls.
So I decided to keep two dial peers for every BRI interface.
I followed your suggestion on eliminate commands:
"incoming called-number" on FXSs,
various "progress_ind" on BRIs
Also I eliminated  "direct-inward-dial" on FXSs,
Today I reconfigured and right tested the dial peers as following:
!   Bri Interfaces
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
!   FXS interfaces
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
destination-pattern 35
no digit-strip
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
no digit-strip
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
no digit-strip
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
no digit-strip
port 0/2/3
Thanks a lot Paolo. :-)
Giorgio.