6500-E SUP2T compatibility

I have two 6500-E chassis with SUP2T on them.
one of the chassis is having the latest WS-X6848-SFP while the other one is having WS-X6748-SFP.
both the line cards are having the same WS-F6K-DFC4-A.
if i will configure VSS between these chassis, will there be any issues ?

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Shouldn't be.

Similar Messages

SUP2T on 7600

I'm looking for a "final / authoritative" confirmation for the fact that SUP2T is supported in the 7606-S chassis, as stated here:
http://www.cisco.com/c/en/us/td/docs/routers/7600/Hardware/Hardware_Guides/Supervisor_Engine_and_Route_Switch_Processor_Guide/76-sup-rsp/SupE01.html#wp1238900
If this is the case, my next questions would be:
- where can the IOS images for SUP2T on 7600 be found for download on Cisco's site?
- does 7600 with SUP2T support the same line cards supported by 6500 with SUP2T?
Many thanks in advance.

upported Hardware
The following 7600 chassis supports Supervisor Engine 2T:
•Cisco 7609-S routers effective with Cisco IOS Release 15.0(1)SY1
•Cisco 7613-S routers effective with Cisco IOS Release 15.1(1)SY
•Cisco 7604 routers effective with Cisco IOS Release 15.1(1)SY
•Cisco 7606-S routers effective with Cisco IOS Release 15.1(1)SY1

Traffic Shaping on 6880 between sites over metro ethernet

Hi
I have a new dual site setup with 6880s at the core at one side and 3650 stack at the other. We have a 200mbps ethernet solution from our service provider but on testing we are maxing at a bit over 100mbps, iperf tests directly on the link are giving 200mbps so I need to apply some shaping to get the full usage from the link. In the past I have used srr bandwidth on metro switches but the 6880s don't support this. So I assume I need to setup policy maps and apply to the physical interface? The interfaces are layer 2 trunks and we are stretching vlans between the sites. E.g. siteA has vlan20 and site B has vlan 20 over the metro ethernet service, site b is layer2 only and all routing and services are provided at siteA
Is it as simple as this? It seems too easy :) So I may be missing something. I just apply this on the physical interface at each side?
policy-map POLICY-S2S-200MB
class class-default
shape average 204800000
policy-map POLICY-S2S-200MB-IN
class class-default
police cir 204800000
conform-action transmit
exceed-action drop
~
int gi1/1/1
service-policy out POLICY-S2S-200MB-OUT out
service-policy out POLICY-S2S-200MB-IN in
Your input would due treaty appreciated!
Thanks,
Aidan.

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Ah, well that's great! (Hmm, now I wonder if same feature is available on 6500 with sup2T or 6807.)
In that case, your output policy might be just as simple as what's in your OP. Cisco isn't really clear whether all their shapers (or policers) are counting L2 and L3 or just L3. I suspect many just count L3. If that's true in this case, you may need to shape about 10 to 15% slower to allow for L2 overhead (this assuming your provider is providing 200 Mbps of "wire" bandwidth.
If you're able to shape on the other side, then there should be no need to also police the ingress. Also, assuming provider limits bandwidth, there's no reason to police ingress at CIR rate.

Point to multipoint L2 transport.

Hello
Iam a bit curious on how to best solve a little problem i seem to have.
How do i terminate a multipoint L2 transport from a ME 3600X
Initial idea was with VFI on all 3 devices but ME3600X dosent seem to support it.
With the use of a VFI i would have made a fully meshed scenario.
I need to transport 1 Vlan to 3 different sites. Preferably it should be l2 transport.
2 of the sites uses cat 6500 with Sup2T
1 site uses ME-3600X
The original idea was to use EVCs on 3600 and bind a service instance to a VFI instance wich would in its turn have 2 peers. One to each 6500.
In the 6500s just terminate the VFI on SVI or physical switchports. Seeing as the configuration options to setup VFI on me3600X seems to be missing does anyone have a tip or 2.
Its our first ME 3600X so the odds are that i have missed something aswell.

You should be looking at VPLS, while this is supported on the 7600, I do not think it is supported on the 7200 and 7300 yet.

How many VRFs support a SUP7E

Hello,
I have a customer that wants to change his CORE devices, he is concerned about the VRFs instances that he can configure, I know that in the SUP2T from the 6500 supports 8,192 VRFs:
MPLS in hardware to enable use of Layer 3 VPNs and EoMPLS tunneling. Up to 8192 VRFs with a total of up to 256K* forwarding entries per system.
According to the next link:
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/catalyst-6500-series-supervisor-engine-2t/data_sheet_c78-648214.html
I want to make a comparison between a 6500 with SUP2T and a 4500 with sUP7E but I can't find anything about the VRFs instances in the SUP7E.
Could anyone please help me answering that question???
Thanks a lot

This is the problem. The customer has 2 4507 with SUP-V I think and he want to upgrade. He asked me about one 6509 with SUP2T but I suggested to upgrade to 4507R+E with SUP7E and VSS, I think that the budget of the customer is low...
He needs at least 4 modules of 48 ports so he can receive all their customers. Regarding SUP7 vs SUP8 the main difference is that the SUP8 supports WLC in the module, and has more switching capacity (928 Gbps vs 848 Gbps of the SUP7).
Thanks again
Let me send a copy of the configuration:
CORE-SWITCH#show run
Building configuration...
Current configuration : 77236 bytes
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
service compress-config
hostname CORE-SWITCH
boot-start-marker
boot system flash bootflash:cat4500-entservicesk9-mz.122-31.SGA9.bin
boot-end-marker
ip vrf TMX1
ip vrf TMX2
ip vrf TMX3
ip vrf TMX4
interface Vlan51
description TMX1
ip vrf forwarding TMX1
ip address 192.168.150.65 255.255.255.240
interface Vlan52
description TMX2
ip vrf forwarding TMX2
ip address 192.168.150.113 255.255.255.240
As you can see the configuration is so simple, I copy only the VRF side so you can see the VRF configuration that he is doing, as far as I know this is VRF-LITE, BTW he has a lot of static routing with VRFs

Verifying Compatibility of VS-S2T-10G (Sup2T) with IDSM-2 (IDSM2)

I am preparing to do an upgrade from Sup720 to Sup2T on a Catalyst 6509E.
I am not seeing compatibility of the Sup2T with the IDSM2 in the release notes.
Could someone verify if the IDSM2 is compatibility with the Sup2T (running s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin)
If not, is there a follow-on product?

Hi Kbyrd,
the IDSM2 seems to be incompatible with the SUP2T.
Software and Hardware Requirements
The following are the IDSM-2 software and hardware requirements:
•Catalyst software release 7.5(1) or later with Supervisor Engine 1A with MSFC2
•Catalyst software release 7.5(1) or later with Supervisor Engine 2 with MSFC2 or PFC2
•Cisco IOS software release 12.2(14)SY with Supervisor Engine 2 with MSFC2
•Cisco IOS software release 12.1(19)E or later with Supervisor Engine 2 with MSFC2
•Cisco IOS software release 12.1(19)E1 or later with Supervisor Engine 1A with MSFC2
•Cisco IOS software release 12.2(14)SX1 with Supervisor Engine 720
•Cisco IDS software release 4.0 or later
Tried to configure the products within 6509 chassis, but that confirms the above info
I will check if any similar module will be available soon.
Regards,
Marco

Apple macbook air compatibility with HP Officejet 6500 Wireless

Two questions
1. If I buy a new current model MacBook Air, will it work with my HP Officejet 6500 Wireless printer?
2. Sometimes when I power up the printer, it can take as long as five minutes to register "ready." Why the erratic time to go online?
Thanks
TT95

Thanks for your swift reply to the Apple/HP compatibility question. Trust it will work when I buy MacBook Air. The HP app available at iTunes store helped us make our older Apple IPad print compatible even though the HP 6500 Wireless is not equipped with AirPrint.
Regarding slowness of HP 6500 to reach "Ready" stage for printing. This is a printer for home use, so it not on a network. It always eventually prints.
Your help is much appreciated.
TT95

OS 10.6.4 compatibility with HP OfficeJet 6500 & Epson Artisan 700

Just purchased MacBook Pro and upgraded iMAC and Mac Pro on my local network to OS 10.6.4. iMAC is connected to local network via Ethernet, other computers and printers HP OfficeJet 6500 and Epson Artisan 700 connected via wireless. All went pretty good except for the two printers. You need to install Rosetta for some 3rd party software to work. It's on the OS 10.6.3 disk.
The HP OfficeJet 6500 is new. In the printer box was a notice to NOT use the enclosed CD's if using OS 10.6. HP manual was terrible. Key was getting the local network operating and then using HP printer keypad to select SETUP/NETWORK SETUP/WIRELESS SETUP WIZARD. It automatically found the name of my local network and then asked me to enter the WEP Key Code of my local network. For some reason the WIRELESS SETUP WIZARD didn't show up for the first day. Now have access to the printer from all computers - even duplex mode works.
Can't say the same for the Artisan 700 we've had for one year and was working good with OS 10.5. The only computer that could not access the Artisan 700 was the one connected via Ethernet to the local network (other computers wireless). Tried downloading Epson drivers, Network setup S/W, etc. Epson says there is a problem with TCP/IP connection and are "working on the problem" - in the mean time use Bonjour driver. I installed print drivers from OS 10.6.3 disk and then did Apple software update. Don't know why but suddenly Bonjour driver showed up and the Artisan printer was recognized by the computer connected to network via ethernet. Also had to manually set up the Artisan printer again using the printer keypad to select local network and enter the WEP Key Code. Duplex printing does not work though. Year ago when we bought the printer had to call Epson who after 1.5 hr on phone got duplex working, but didn't know why or how. I'd taken notes and tried same thing, but didn't work this time.
Perhaps this will help other people deciding to do an OS upgrade.

Thanks for response on the Epson duplex mode problem. I downloaded the updater, but it would NOT open after I installed it. The install created a second file called InkJet Printer 2 (original was w/o the 2). The updater tool is v 8.33 on the one just downloaded while the existing one was v 6.66, so definitely a later version. The v 6.66 gave message "unexpected quit", so it would not open either. Got same results on iMAC and MAC PRO. Do I delete the original InkJet printer file before installing the new download? Was afraid to as afraid driver would not work at all. What am I doing wrong???
When select duplex mode in the print window get message "duplexer not installed" on both computers.

6500s TV-out cable on other phone compatibility

6500s tv-out cable ca-92u
is it able to use on other model such as 5610XM since mini usb connector is found on both devices.
or
the tv-out system is phone dependant or cable dependant like headsets and other accessories?

first of all, thanks for ur reply.
you've been tried that b4?
I need an actual test result but not just some theoretically thought.
5610's camera capability on still image and video capturing is almost the same quality found on 6500s
if it's able to use the tv-out cable as well i think that would be a great enhancement for this modelMessage Edited by feimeng on 26-Nov-200702:29 AM

Compatibility Windows XP HP officejet 6500 (E709) printer with new HP Pavilion

I just purchased a HP Pavilion 23 all-in-one. The store where I bought it said that they could not set up my HP Officejet 6500 (E709) printer because it was not compatible with the new Windows installed on the Pavilion. The CD for the printer says Windows XP, Vista Version 12.00 on the label. I hate to give up a perfectly good printer just because it is not compatible with the new PC. Is there a fix for this or was the technician just not looking in the right place for the driver.

Here is a link for the 6500 E709a drivers.
There are a few E709 models, so if yours is not a E709a model post back with the correct model #.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

6500-E with SUP720 compatibility with 10g module

I have 6509-E chasis with supervisor VS-S720-10G.
I need to add a new WS-X6708-10G-3C= module to this same chasis.
As per the cisco datasheet both the cards and the supervisor are compatible, just need to confirm this.

WS-X6708-10G-3C will never be compatible with Sup2T. The Sup2T has DFC4/PFC4 and the card has DFC3/PFC3 card which cannot be upgraded.

Nokia 6500 slide & micro SDHC compatibility

hi!
I just got my nokia 6500 slide & wanted to pair it up with a good memory card (I was thinking 6 GB, initially, then I read some of the comments in this board and desisted).
hence, I was wondering whether it accommodates 4GB Micro SDHC cards, which are slightly larger than the regular Micro SD cards. While going through previous postings I found two contradictory comments (one says yes, the other no), so I wanted to double check with current 6500 owners before buying my own card.
thanks!
ff_boston

oh , its been a while , I'd like to thank you all for replying to my query above , ive already got the phone ... no problems of resetting ringtones/themes so far.. unless ofcourse yes you remove the backcover and your tones/themes were stored on the mc , mine are on the ph.memory.
overall good phone.. though it hangs when manual tuning the Radio FM.
I've not got a microsdhc card for it yet.. ok to the above post im assuming it wont take a 4GB KINGSTON microSDHC or it wont take in Kingston as a brand...
I'm going to bite the bullet and try out what Knapjee here tried - sandisk 4gb microsdhc .. though i'd like reassurances.
Cheers for now ,

HP Officejet 6500 e709n - Solution Center Scan Malfunction

I've recently purchased a new laptop with Windows 8.1 already installed on it. I've had my HP 6500 for years and it has worked perfectly - all functions. When going online to download the drivers to my new laptop, all messages indicate the installation is complete, but I can only print. The scan function does not work at all - from the solution center or from the keys on the printer. I've called HP Help (I even have a case number) and they have remotely taken control of my laptop several times with no scan success. They have told me it's a Microsoft software issue. I called Microsoft, and they are telling me it's a HP issue. I know the actual printer itself is perfectly ok, because all function still work on my old laptop. Si, the conclustion is that there is a compatibility issue with Windows 8.1 and the scan function (as I can print just fine). Is there a chance the driver on the HP website is not updated for the scan funtion with Windows 8.1? Is there a fix for this that I am not aware of? I prefer not to use third party apps, as this is the reason I had to purchase a new laptop - because of viruses. Help!!! I need the scan funtion (to .pdf) to work ASAP as I use my printer/scan function for business. Is there a fix? I prefer not to buy a new printer, as this one works just fine, except not on Windows 8.1. Again, HELP.............

Hi MsOP,
I see that you that you are unable to scan on the Windows 8.1 computer. With a few steps we should be
able to resolve this issue.
Did you download the Full Feature Software drivers?
HP Officejet 6500 Wireless All-in-One Printer - E709n Drivers.
Temporarily turn off your Antivirus Software to see if it is blocking it.
Here are some additional steps you can do if you are still having issues.
'An error occurred while communicating with scanning device' Message Displays When Scanning (Windows...
Also download and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it.
This document is to Check the Windows Image Acquisition (WIA) services.
Windows: HP Scan Software Does Not Open or Scan on a Printer Using a USB Connection.
Disregard the title.
Go to Solution three: Check the Windows Image Acquisition (WIA) services.
You might have to configure the firewall.
Configuring a Firewall to Allow a Connection with the All-in-One in Windows.
How is the printer connected? (USB/Ethernet/Wireless)
What were the results when you ran the Print and Scan Doctor? (did it print or scan, any error messages)
Were you able to scan from another application?
Please provide in detail the results if you are still having issues.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Upgrade power mac 6500/225 running 8.5 to 9.1(poss?

Can anyone tell me if I can upgrade my power pc 6500/225 running 8.5 with upgraded memory to 96MB to run 9.1. If so, what are the steps to take.

Hi, stacks -
Welcome to Apple's Discussions.
According to Apple KBase Article #25114 - Mac OS 8, 9: Compatibility With Macs your machine is supported for OS 9.1.
You will need to acquire a retail OS 9 Install CD in some version, then update it to OS 9.1 using download updaters (if necessary).
You can often get retail OS 9 Install CD's at sites like these -
http://store.yahoo.com/hardcoremac/index.html - Apple Reseller
http://www.applerescue.com/
EBay is another possibility.
Regardless of the source, be sure to get a retail OS 9 Install CD - those are white, with a large gold 9 on them; the retail OS 9 Install CD's have a universal installer; model-specific Install CD's do not.
In case you need the updaters -
Article #75103 - Mac OS 9.1 - Download and Info
Article #120030 - Mac OS 9.2.1 - Download and Info
Article #75186 - Mac OS 9.2.2 - Download and Info
Since you want to end up at OS 9.1, I would suggest obtaining a retail OS 9.1 Install CD - you would not then need to use any download updaters for the OS itself, although there have been several incremental updates to some of the component software.
<hr>
The steps -
• Boot to the OS 9 Install CD.
• (Optional, but recommended) Run the utility Disk First Aid from the Utilities folder on the CD. Let DFA examine your drive, and allow it to repair anything it finds wrong (if it can). Doing this can prevent some errors caused by problems with a drive.
• Run the installer (Mac OS Install).
• On the second page of the installer select to do a Clean Install. This will not erase anything in the drive. Instead, it will install a brand new, 'clean' System Folder, rename the old one to Previous System Folder, install a set of standard OS 9 utilities and a couple of folders, and little else.
Article #58176 - Mac OS 8, Mac OS 9: Performing a Clean Installation
• Follow the prompts, accepting a standard install of the OS. The installer will select the correct OS files needed by your machine.
• Once it is done, test boot to the new OS.
<hr>
As soon as is convenient and provided you have an internet connection available to the machine, run the Software Update control panel that is part of OS 9. You will be offered a list of updates applicable to OS 9 which were released after the OS itself was released. This can include updates to things like QuickTime, CarbonLib, OpenTransport, and other services and software.
Suggestion - do not allow the Software Update control panel to download and install those for you. Instead, note their names, then go to the Apple download site and download them and install them manually. In addition to being able to keep the installers, you will avoid any issues which Software Update sometimes has it does that work.
It would not hurt to rebuild the desktop file after the software install process.
<hr>
Before starting, though, check to see what format your hard drive is. OS 9 runs best when the drive is formatted as Mac OS Extended (also called HFS+); this format also makes much better use of available disk space, particularly when drives get into GB sizes.
If your drive is formatted as Mac OS Standard, the normal way to reformat it is to use OS 9's Drive Setup utility (it's in the Utilities folder on all OS 9 Install CDs) to re-initialize and reformat the drive. Note, though, that this will erase everything on the drive, so back up anything you do not want to lose before doing it.
There is another way, one that does not erase the drive. Alsoft, the makers of the DiskWarrior disk utility program, also make a utility named PlusMaker which can convert a drive's format from Mac OS Standard to Mac OS Extended without erasing it.

QoS Packets not matching on 6500 with SUP720-10GE and SU2T

Hi,
I do not see packets matching in policy.
output below:
Switch#sh policy-map interface vlan 2232
Vlan2232
Service-policy input: HARDPHONE-VVLAN
Class-map: VOICETRAFFIC (match-all)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: access-group name VOICETRAFFIC
Class-map: VOICESIGNALING (match-all)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: access-group name VOICESIGNALING
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: any
0 packets, 0 bytes
5 minute rate 0 bps
I also not find packets matching ACL:
switch#sh access-lists
Extended IP access list VIDEOTRAFFIC
10 permit udp any any range 16384 32767
Extended IP access list VOICESIGNALING
10 permit tcp any 10.128.0.0 0.3.255.255 range 2000 2002
20 permit tcp any 10.128.0.0 0.3.255.255 eq 5060
30 permit udp any 10.128.0.0 0.3.255.255 eq 5060
40 permit tcp any 172.20.10.0 0.0.1.255 range 2000 2002
50 permit tcp any 172.20.10.0 0.0.1.255 eq 5060
60 permit udp any 172.20.10.0 0.0.1.255 eq 5060
Extended IP access list VOICETRAFFIC
10 permit udp 10.128.0.0 0.63.255.255 10.128.0.0 0.63.255.255 range 16384 32767
I checked policies, they looks applied correctly.
On SUP-720-10GE, I modified ACL to 'permit udp any any' but not found any matching packets. There are plenty of IP phones connected directly to this switch belongs to voice VLAN. I applied VLAN based QoS under voice VLAN and other VLANs too.
I observed different thing on SUP 2T. I saw packets matching ACL statement 'permit udp any any' but when I took off this line, ACL was not showing packets matching.
OUTPUT of IP phones connected to switch:
switch#sh cdp neighbors | in SEP
SEP0008308A5D7B Gig 13/38 143 H P M IP Phone Port 1
SEP0008308A5DE0 Gig 10/1 121 H P M IP Phone Port 1
SEP0023049C6348 Gig 3/42 152 H P M IP Phone Port 1
SEP0021A02D64D4 Gig 9/28 120 H P M IP Phone Port 1
SEP1C6A7AE0588E Gig 3/9 127 H P M IP Phone Port 1
SEP00229059969E Gig 12/48 166 H P M IP Phone Port 1
SEP0008308AF26F Gig 2/7 161 H P M IP Phone Port 1
SEP00235EB7BE0E Gig 4/2 154 H P M IP Phone Port 1
SEP00229059BE5A Gig 6/37 158 H P M IP Phone Port 1
SEP1CAA07115CF3 Gig 12/29 148 H P M IP Phone Port 1
SEP00235EB7884F Gig 9/3 156 H P M IP Phone Port 1
SEP0008308B03FB Gig 2/30 178 H P M IP Phone Port 1
SEP006440B42CD3 Gig 3/45 132 H P M IP Phone Port 1
SEP0022905991C9 Gig 11/4 145 H P M IP Phone Port 1
SEP0008308A5E6C Gig 6/36 124 H P M IP Phone Port 1
SEP006440B427CA Gig 13/31 170 H P M IP Phone Port 1
SEP006440B425FF Gig 3/19 168 H P M IP Phone Port 1
SEP0008308A7AD7 Gig 2/3 159 H P M IP Phone Port 1
SEP0008308A3EB2 Gig 10/4 132 H P M IP Phone Port 1
SEP002414B45A0E Gig 10/28 170 H P M IP Phone Port 1
SEP04C5A4B19C8B Gig 2/15 162 H P M IP Phone Port 1
SEP006440B43DE6 Gig 9/48 162 H P M IP Phone Port 1
SEP006440B42B0D Gig 9/23 179 H P M IP Phone Port 1
Could anyone please help, how to make sure that packets are hitting correct ACL and policy on 6500 with SUP720-10GE and SUP2T.
Thanks,
Pruthvi

Please note that 6500 is used as L2 switch only and SVI are used for applying policies only.
Configuration below:
class-map match-all VOICESIGNALING
match access-group name VOICESIGNALING
class-map match-all VOICETRAFFIC
match access-group name VOICETRAFFIC
class-map match-all VIDEOTRAFFIC
match access-group name VIDEOTRAFFIC
policy-map HARDPHONE-VVLAN
class VOICETRAFFIC
police flow mask src-only 128000 8000 conform-action set-dscp-transmit ef exceed-action drop
class VOICESIGNALING
police flow mask src-only 32000 8000 conform-action set-dscp-transmit cs3 exceed-action policed-dscp-transmit
class class-default
police flow mask src-only 32000 8000 conform-action set-dscp-transmit default exceed-action policed-dscp-transmit
policy-map STUDENT-DVLAN
class class-default
police flow mask src-only 25000000 1562500 conform-action set-dscp-transmit default exceed-action policed-dscp-transmit
policy-map STAFF-DVLAN
class VOICESIGNALING
police flow mask src-only 32000 8000 conform-action set-dscp-transmit cs3 exceed-action policed-dscp-transmit
class VOICETRAFFIC
police flow mask src-only 128000 8000 conform-action set-dscp-transmit ef exceed-action drop
class VIDEOTRAFFIC
police flow mask src-only 2000000 150000 conform-action set-dscp-transmit ef exceed-action drop
class class-default
police flow mask src-only 50000000 1000000 conform-action set-dscp-transmit ef exceed-action drop
ip access-list extended VOICESIGNALING
remark Skinny and SIP protocols From Phones to Voice Core Infrastructure
permit tcp any 10.128.0.0 0.3.255.255 range 2000 2002
permit tcp any 10.128.0.0 0.3.255.255 eq 5060
permit udp any 10.128.0.0 0.3.255.255 eq 5060
permit tcp any 172.20.10.0 0.0.1.255 range 2000 2002
permit tcp any 172.20.10.0 0.0.1.255 eq 5060
permit udp any 172.20.10.0 0.0.1.255 eq 5060
ip access-list extended VOICETRAFFIC
permit udp any any dscp ef
permit udp 10.128.0.0 0.63.255.255 10.128.0.0 0.63.255.255
permit udp any any range 16384 32767 dscp ef
ip access-list extended VOICESIGNALING
remark Skinny and SIP protocols From Phones to Voice Core Infrastructure
permit tcp any 10.128.0.0 0.3.255.255 range 2000 2002
permit tcp any 10.128.0.0 0.3.255.255 eq 5060
permit udp any 10.128.0.0 0.3.255.255 eq 5060
permit tcp any 172.20.10.0 0.0.1.255 range 2000 2002
permit tcp any 172.20.10.0 0.0.1.255 eq 5060
permit udp any 172.20.10.0 0.0.1.255 eq 5060
ip access-list extended VIDEOTRAFFIC
permit udp any any range 16384 32767 dscp ef
interface Vlan104
description PolicyOnlyInt
no ip address
service-policy input STAFF-DVLAN
interface Vlan105
description PolicyOnlyInt
no ip address
service-policy input STAFF-DVLAN
interface Vlan573
description PolicyOnlyInt
no ip address
service-policy input PUBLIC-DVLAN
interface Vlan604
description PolicyOnlyInt
no ip address
service-policy input PUBLIC-DVLAN
interface Vlan654
description PolicyOnlyInt
no ip address
service-policy input STUDENT-DVLAN
interface Vlan674
description PolicyOnlyInt
no ip address
service-policy input PUBLIC-DVLAN
interface Vlan807
ip address 172.18.128.5 255.255.255.0
interface Vlan860
description PolicyOnlyInt
no ip address
service-policy input PUBLIC-DVLAN
interface Vlan2016
description PolicyOnlyInt
no ip address
service-policy input HARDPHONE-VVLAN
interface Vlan3124
description PolicyOnlyInt
no ip address
shutdown
service-policy input HARDPHONE-VVLAN
switch#sh access-lists
Extended IP access list VOICESIGNALING
10 permit tcp any 10.128.0.0 0.3.255.255 range 2000 2002
20 permit tcp any 10.128.0.0 0.3.255.255 eq 5060
30 permit udp any 10.128.0.0 0.3.255.255 eq 5060
40 permit tcp any 172.20.10.0 0.0.1.255 range 2000 2002
50 permit tcp any 172.20.10.0 0.0.1.255 eq 5060
60 permit udp any 172.20.10.0 0.0.1.255 eq 5060
Extended IP access list VOICETRAFFIC
10 permit udp any any dscp ef <----- not showing any match
11 permit udp 10.128.0.0 0.63.255.255 10.128.0.0 0.63.255.255 <----not shwoing any match
12 permit udp any any range 16384 32767 dscp ef<----not shwoing any match
If I user "permit udp any any ", acl is showing match.
switch#sh access-lists
Extended IP access list VOICETRAFFIC
10 permit udp any any dscp ef
11 permit udp 10.128.0.0 0.63.255.255 10.128.0.0 0.63.255.255
12 permit udp any any range 16384 32767 dscp ef
13 permit udp any any (527055 matches)

6500-E SUP2T compatibility

Similar Messages

Maybe you are looking for