857 Router Dot11Radio0 reset - problem

Hi all
I have just upgraded the IOS in a 857 Router to this:
ROUTER#sh version
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
but now I can't get the dot11radio 0 interface to come up. I just get a message saying the interface is reset and line protocol is down. I get this error message when I remove and re-insert the SSID -
ROUTER(config)#int dot11radio 0
ROUTER(config-if)#no ssid SSID
*Mar 1 04:04:24.655: %DOT11-4-NO_SSID: No SSID configured. Dot11Radio0 not started.
ROUTER(config-if)#ssid SSID
ROUTER(config-if)#
*Mar 1 04:04:24.655: %DOT11-4-NO_SSID: No SSID configured. Dot11Radio0 not started.
'Show run' shows the ssid is configured on the interface but the error message is saying that it doesn't have an ssid, even after a 'copy run start' and a 'reload'
I have spent hours on this and I can't find the problem. I have done numerous 'write erase' and 'reload' as well as re-installing the IOS twice.
Any advice would be very appreciated.
--- show output ---
ROUTER# sh ip int dot11Radio 0
Dot11Radio0 is reset, line protocol is down
Internet protocol processing disabled
ROUTER#sh int dot
ROUTER#sh int dot11Radio 0
Dot11Radio0 is reset, line protocol is down
Hardware is 802.11G Radio, address is xxxx.xxxx.xxxx (bia xxxx.xxxx.xxxx)
Description: WLAN
MTU 1500 bytes, BW 54000 Kbit/sec, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
ROUTER#
--- show run summary ---
dot11 syslog
dot11 ssid SSID
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 0 ppppppppppp
bridge irb
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0.1 point-to-point
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dot11Radio0
description WLAN
no ip address
encryption vlan 1 mode ciphers tkip
ssid SSID
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
infrastructure-client
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
description Bridged LAN and WLAN
no ip address
ip virtual-reassembly
ip tcp adjust-mss 1452
bridge-group 1
bridge-group 1 spanning-disabled
interface Dialer1
description $OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
no ip route-cache cef
no ip route-cache
ip tcp adjust-mss 1242
no ip mroute-cache
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap ppppppp
ppp chap refuse
ppp pap sent-username uuuuuuuuu password 0 ppppppp
interface BVI1
ip address xxx.xxx.xxx.xxx 255.255.255.0
ip nat inside
ip virtual-reassembly

Not to worry everyone. I have figured it out. I replaced the dot11radio 0 intface with this config
interface Dot11Radio0
description WLAN
no ip address
encryption vlan 1 mode ciphers tkip
ssid SSID
no cdp enable
no ip address
no shutdown
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
infrastructure-client
and added in this config for the sub interface which was missing:
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
Thanks anyway.

Similar Messages

I am loosing configuration when I power off my Cisco 857 router

I bought new Cisco 857 router from the shop. Router must have been used before as I couln't go in with default username/password cisco/cisco.
Well I followed instruciton and reset password to username and password. Now I finally connected to the Cisco CP express over my IE browser.
I found out that somebody was using a router from the shop so this is why I coun't log to it in the first place. Anyway problem is that when I changed configuration and applied settings it remembers it until I power it off. When I power it on again it remembers all settings from that shop.
It reverts everything back: IP address, previous level 15 account and password - everything like after password reset.
I tried it again and it again lost settings. So I found following instruction:
http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed again all settings on the router. My settings are again lost after power off/on. I noticed that when I do first bit it does show
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enableCisco#show startUsing 3359 out of 131072 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Cisco!boot-start-markerboot-end-marker!logging buffered 51200 warningsenable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.!no aaa new-model!crypto pki trustpoint TP-self-signed-3185909327 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3185909327 revocation-check none rsakeypair TP-self-signed-3185909327!!crypto pki certificate chain TP-self-signed-3185909327 certificate self-signed 01 nvram:IOS-Self-Sig#5.cerdot11 syslogno ip dhcp use vrf connectedip dhcp excluded-address 10.10.10.1!ip dhcp pool ccp-pool   import all   network 10.10.10.0 255.255.255.248   default-router 10.10.10.1   lease 0 2!!ip cefno ip domain lookupip domain name molinary.com!!!username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.username username privilege 15 password 0 password!!archive log config hidekeys!!!!!interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto!interface ATM0.1 point-to-point description $ES_WAN$ ip nat outside ip virtual-reassembly pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 !!interface FastEthernet0!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$ ip address 10.10.10.1 255.255.255.248 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452!interface Dialer0 ip address dhcp encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname [email protected] ppp chap password 0 netgear01 ppp pap sent-username [email protected] password 0 netgear01!ip forward-protocol nd!ip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000ip nat inside source list 1 interface ATM0.1 overload!access-list 1 remark INSIDE_IF=Vlan1access-list 1 remark CCP_ACL Category=2access-list 1 permit 10.10.10.0 0.0.0.7dialer-list 1 protocol ip permitno cdp run!control-plane!banner exec ^C% Password expiration warning.-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this deviceand it provides the default username "cisco" for one-time use. If you havealready used the username "cisco" to login to the router and your IOS imagesupports the "one-time" user option, then this username has already expired.You will not be able to login to the router with this username after you exitthis session.It is strongly suggested that you create a new username with a privilege levelof 15 using the following command.username <myuser> privilege 15 secret 0 <mypassword>Replace <myuser> and <mypassword> with the username and password youwant to use.-----------------------------------------------------------------------^Cbanner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C!line con 0 login local no modem enableline aux 0line vty 0 4 privilege level 15 login local transport input telnet ssh!scheduler max-task-time 5000endCisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#show versionCisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARECisco uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)Configuration register is 0x2102Cisco#Cisco#Cisco#Cisco#endTranslating "end"% Unknown command or computer name, or unable to find computer addressCisco#reloadProceed with reload? [confirm]*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. Reload Reason: Reload Command.System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARETechnical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memoryBooting flash:/c850-advsecurityk9-mz.124-15.T12.binSelf decompressing the image : ############################################## [OK]              Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.           cisco Systems, Inc.           170 West Tasman Drive           San Jose, California 95134-1706Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814E7240This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)no ip dhcp use vrf connected               ^% Invalid input detected at '^' marker.SETUP: new interface NVI0 placed in "shutdown" statePress RETURN to get started!*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state toup*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_team*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoinga cold start*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to down*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administratively down*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state toup*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state toup*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state toup*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3, changed state to down*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2, changed state to down*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1, changed state to down*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to upAuthorized access only!===========================================
Please help me as I am stuck and can't go any further....

Hi David White,
Alternatively, after password recovery you can modify the configuration to be what you want, and then issue:
   write memory
to save the configuration. You can then verify that your changes have been saved to the startup config by issuing:
   show startup-config"
The only good thing is that when I switch off a router it erase configuration except my new password which I created after password reset. Everything else is getting vanished (ADSL settings, DHCP, routing ) everything. Even new admin accounts I created.
Well have a question to your above comments. I am new in Cisco so please put as much detail as you can for me to understand. When you say modify configuration do you mean to go to Cisco CP Express graphical interface and then connect router to hyper terminal and execute above commands?
Why router doesn't remember this anyway. There must be some option to change in configuration to make thing permanent when I hit apply changes in Cisco CO Express otherwise it is pointless to heve it.
Phillip
write memory
is
copy running-config startup-config"
Can't this be done via Cisco CP Express or set up router to copy this every time I change this in graphical interface rather going to command line to achnoledge it?
I understand your concern about this router and somebodie's configuration details as you want things to be un-used when you buy them - true. ADSL details belongs to the shop which sold me the router so that is why I don't make a big problem about this. We take most of hardware from this shop and have discount and many good deals with them so I think they have been just testing it and forgot to erease their config. It might be that someone has returned router to the shop and they have repaired it and tested it.
I hope this is a normal behaviour of this router as I have option to replace it in case this is a fault.
Could you please write me step by step guide how can I make changed options stay permanently on router?
thank you
Dragan

WRT54GX2 Router Webpage Connection Problem

I just recently downgraded from Vista to XP (Nothing worked with it). I installed all my drivers and everything works fine...except when i try to connect to my router web page at http://192.168.1.1 it wont connect. It tries to load it for about 5 minutes and then it says it cant connect. Any suggestions on how to solve this problem? IP Address: 192.168.1.136 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1

How did your computer get an address of 192.168.1.136 ?
1) Are you using a fixed LAN IP address?
2) Did you change your DHCP server range to start at 192.168.1.136 ?
3) If you are not using the default DHCP server range of 192.168.1.100 thru 192.168.1.149 , then please state your DHCP server range.
To view the router's web pages:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, you need to reset the router to factory defaults. Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.

Route or NAT problem?

Hi Everyone,
We have an ASA 5540 at our data center, with ASA 5505's at most remote sites.
At the sites without layer 3 switches behind the ASA 5505's, we can't reach the data center internal network through the ASA for flow-export, etc.
So, what I'm basically saying is, even though the tunnel is up and everything behind the branch ASA can reach the data center networks fine, the ASA itself cannot reach hosts on the data center network.
I'm hoping to configure these ASA 5505's so I can do flow export and SNMP logging from them, but without this routing or nat problem resolved, they just won't do it.
Doing a packet tracer from the ASA 5505 to the data center server I'm most focused on, reveals this:
BRANCH5505f01# packet input inside icmp 10.15.16.1 8 0 10.1.1.15 detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0b6698, priority=1, domain=permit, deny=false
        hits=1004755, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=inside, output_ifc=any
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.1.1.15       255.255.255.255 outside
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (rpf-violated) Reverse-path verify failed
I am thinking the problem is NAT related, but with the new ASA NAT rule format due to v9.1... struggling to get a grip on where it is... any thoughts/help are appreciated.
Ken
Here is the relevant config for the Branch ASA and also the relevant config from the data center ASA:
Branch ASA Config Parts:
: Saved
ASA Version 9.1(2)
hostname BRANCHASA5505
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
description LAN_NETWORK
nameif inside
security-level 100
ip address 10.15.6.1 255.255.254.0
interface Vlan2
nameif outside
security-level 0
ip address <outside ip> 255.255.255.248
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object-group network BRANCH_NETWORKS
description BRANCH LOCAL NETWORKS
network-object 10.15.6.0 255.255.254.0
object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 134.200.131.0 255.255.255.0
network-object 134.200.220.0 255.255.255.0
network-object 134.201.2.0 255.255.255.0
network-object 163.243.195.0 255.255.255.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object 10.1.3.0 255.255.255.0
network-object 10.31.2.0 255.255.255.0
network-object 10.1.1.0 255.255.255.0
network-object 172.26.1.0 255.255.255.0
object-group network NETWORK_MGMT
network-object 10.0.0.0 255.0.0.0
access-list DATACENTER_VPN_ACL remark *******************************************************************
access-list DATACENTER_VPN_ACL remark * FOR VPN CONNECTION TO DATACENTER/VEYANCE NETWORKS *
access-list DATACENTER_VPN_ACL remark *******************************************************************
access-list DATACENTER_VPN_ACL extended permit ip host <outside ip> host <outside ip datacenter asa>
access-list DATACENTER_VPN_ACL extended permit ip object-group BRANCH_NETWORKS object-group LAN_NETWORKS
access-list INSIDE_NONAT extended permit ip object-group BRANCH_NETWORKS object-group LAN_NETWORKS
access-list INSIDE_FILTER extended permit tcp any4 any4 eq www
access-list INSIDE_FILTER extended permit tcp any4 any4 eq 8080
logging host inside 10.1.1.15
flow-export destination inside 10.1.1.15 2055
ip verify reverse-path interface inside
ip verify reverse-path interface outside
nat (inside,outside) source static LAN_NETWORKS LAN_NETWORKS destination static BRANCH_NETWORKS BRANCH_NETWORKS route-lookup
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
nat (inside,outside) source dynamic any interface
object network obj_any
nat (inside,outside) dynamic interface
access-group FROM_OUTSIDE in interface outside
route outside 0.0.0.0 0.0.0.0 <outside ip gateway> 1
route outside 10.1.1.15 255.255.255.255 <outside ip datacenter asa> 1
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
tunnel-group <outside ip datacenter asa> type ipsec-l2l
tunnel-group <outside ip datacenter asa> ipsec-attributes
ikev1 pre-shared-key *****
class-map type regex match-any DomainBlockList
match regex DomainList-Netflix
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map inspection_default
match default-inspection-traffic
class-map httptraffic
match access-list INSIDE_FILTER
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action log
class BlockDomainsClass
reset log
policy-map URL-filter-policy
class httptraffic
inspect http http_inspection_policy
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect http
class class-default
flow-export event-type all destination 10.1.1.15
service-policy URL-filter-policy interface inside
prompt hostname context
Datacenter ASA Config Parts:
ASA Version 9.0(1)
hostname DATACENTERASA5540
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface GigabitEthernet0/0
description *** TO OUTSIDE NETWORK AT DATACENTER ***
speed 100
duplex full
nameif OUTSIDE
security-level 0
ip address <outside ip>
interface GigabitEthernet0/1
description *** TO INSIDE NETWORK ***
nameif INSIDE
security-level 100
ip address 10.1.3.2 255.255.255.0
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 134.200.131.0 255.255.255.0
network-object 134.200.220.0 255.255.255.0
network-object 134.201.2.0 255.255.255.0
network-object 163.243.195.0 255.255.255.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object 10.1.3.0 255.255.255.0
network-object 10.31.2.0 255.255.255.0
network-object 10.1.1.0 255.255.255.0
network-object 172.26.1.0 255.255.255.0
object-group network DATACENTER_NETWORKS
network-object 10.1.0.0 255.255.0.0
object-group network BRANCH_NETWORKS
network-object 10.15.6.0 255.255.254.0
access-list BRANCH_VPN_ACL remark ****************************************************
access-list BRANCH_VPN_ACL remark * FOR SITE TO SITE VPN TO BRANCH WV USA *
access-list BRANCH_VPN_ACL remark ****************************************************
access-list BRANCH_VPN_ACL extended permit ip host <outside ip> host <outside ip branch asa>
access-list BRANCH_VPN_ACL extended permit ip object-group LAN_NETWORKS object-group BRANCH_NETWORKS
flow-export destination INSIDE 10.1.1.15 2055
flow-export template timeout-rate 1
flow-export delay flow-create 180
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
nat (INSIDE,OUTSIDE) source static LAN_NETWORKS LAN_NETWORKS destination static BRANCH_NETWORKS BRANCH_NETWORKS route-lookup
access-group FROM_OUTSIDE in interface OUTSIDE
route OUTSIDE 0.0.0.0 0.0.0.0 <outside ip> 1
route INSIDE 10.0.0.0 255.0.0.0 10.1.3.1 1
route OUTSIDE 10.15.6.0 255.255.254.0 <outside ip branch asa> 1
crypto map OUTSIDE-MAP 156 match address BRANCH_VPN_ACL
crypto map OUTSIDE-MAP 156 set pfs
crypto map OUTSIDE-MAP 156 set peer <outside ip branch asa>
crypto map OUTSIDE-MAP 156 set ikev1 transform-set ESP-3DES-MD5 ESP-3DES-SHA
tunnel-group <outside ip branch asa> type ipsec-l2l
tunnel-group <outside ip branch asa> ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class class-default
flow-export event-type all destination 10.1.1.15
user-statistics accounting
service-policy global_policy global
smtp-server 172.19.1.137
prompt hostname context
call-home reporting anonymous
Again, any help you can provide is appreciated... will vote for best...

I ran it, with the source IP corrected (it is 10.15.6.2):
BRANCHASA# packet input inside icmp 10.15.6.2 8 0 10.1.1.15 detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0b6698, priority=1, domain=permit, deny=false
        hits=1203279, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=inside, output_ifc=any
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 3
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
NAT divert to egress interface outside
Untranslate 10.1.1.15/0 to 10.1.1.15/0
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.15.6.0       255.255.254.0   inside
Phase: 5
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
Static translate 10.15.6.2/0 to 10.15.6.2/0
Forward Flow based lookup yields rule:
in id=0xcb12f2f0, priority=6, domain=nat, deny=false
        hits=15824, user_data=0xcb0fdef8, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=outside
Phase: 6
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcaa712e0, priority=0, domain=nat-per-session, deny=true
        hits=77610, user_data=0x0, cs_id=0x0, reverse, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=any, output_ifc=any
Phase: 7
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0bc128, priority=0, domain=inspect-ip-options, deny=true
        hits=91404, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=any
Phase: 8
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0bbc28, priority=66, domain=inspect-icmp-error, deny=false
        hits=4585, user_data=0xcb0bb238, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
        src ip/id=0.0.0.0, mask=0.0.0.0, icmp-type=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, icmp-code=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=any
Phase: 9
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
out id=0xcb0c1218, priority=70, domain=encrypt, deny=false
        hits=708, user_data=0xbf63c, cs_id=0xcb9ad918, reverse, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=any, output_ifc=outside
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
Forward Flow based lookup yields rule:
out id=0xcb12fb00, priority=6, domain=nat-reverse, deny=false
        hits=15837, user_data=0xcb124438, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=outside
Phase: 11
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 143081, packet dispatched to next module
Module information for forward flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_adjacency
snp_fp_encrypt
snp_fp_fragment
snp_ifc_stat
Module information for reverse flow ...
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow

WRT160N V3 Xbox 360 trouble router randomly resetting PLEASE HELP

For Christmas 2009, I received the wrt160n v3 Linksys by Cisco router. This router worked fine until about early November of 2010, when I would turn on my xbox to play a multiplayer game, and the router would randomly reset and i would lose my connection, as well as all the computers connected to the router would lose their connection to the internet. I actually sent that one back to linksys through an rma and received a new one of the same model and version, and I am still having the same problem. The router even resets when I am not on my xbox, simply just on my laptop. It is incredibly frustrating and cannot seem to find any help on the internet. Does anyone else have this problem? Are there any solutions? Is it my router or could it be my xbox screwing everything up? Any help is welcome, thank you very much

nevermind my router just reset while playing xbox. mtu is 1365, i unchecked that box, and opened my nat type, and it still reset. im starting to get extremely dissatisfied with your products

RG54G2 Wireless Router Internet Connection Problem

Hi,
(apologies for the long message - trying to cover all details - summary: wireless router often drops internet connection)
I recently bought an RG54G2 Wireless Router, a CB54G2 PCMCIA Wireless card and a D-Link GWL-630 PCMCIA Wireless card. In addition to two laptops connected to the wireless router WLAN, I have two PCs (one Win WP Pro SP 1 and one Win98SE) connected to the router via wired LAN. I also have a SurfBoard SB3100 Cable Modem connected to the WAN port (this connects to my ISP - Optusnet (Australia) via DHCP).
The problem I have is that the internet connection is disconnected many times a day (often every few minutes, sometimes an hour or so). I am able to reconnect by resetting the wireless router via the wireless router configuration page. When the internet is disconnected I am still able to access the computers on the LAN/WLAN (via Windows Explorer and Ping), I am also able to ping the router and the Cable Modem, but nothing outside of the cable modem.
Also, when the internet is disconnected the System Status page indicates that the router is still connected to the internet, and the Diagnostics page passes the Test Connection test, though no external pings work.
I did not have this problem when the cable modem was connected directly to the Win98SE PC (and other PCs via ICS).
I have disabled the WLAN and the problem still exists with only the wired LAN.
I have changed numerous settings in the wireless router config page with no success (eg disabling DHCP and setting each IP address, minimising LAN and WLAN speeds to 10 and 11MBps plus others).
I have upgraded the wireless router firmware to R1.0.6.0 (no change to the problem).
Searching on Google I have found several other cases of routers with unstable internet connections (none refering to the MSI routers), but none had solutions that helped my situation (most replies suggested updating the firmware).
Any suggestions of how to make the router internet connection stable?
Thanks,
Mike

maybe this is the FIX 4 wireles router internet connection problem
please let me know if any one fix the problem with this tips
thankz
M. B. Feb 6 2004, 8:20 am hide options
Newsgroups: comp.os.ms-windows.networking.windows
From: "M. B." - Find messages by this author
Date: Fri, 06 Feb 2004 16:20:48 GMT
Local: Fri, Feb 6 2004 8:20 am
Subject: SOLUTION to my router loosing connection to Windows XP
Reply | Reply to Author | Forward | Print | Individual Message | Show original | Report Abuse
I am happy to report that after 8 days of constant battles, reboots, phone
calls, cable pulling, router changing, it seems that I finally have found a
combination that has had me using Verizon DSL account for over 12 hours so
far without any kind of interruptions.
Since so many of you tried giving me comments and suggestions, I felt that
it is necessary for me to post this here so that the next person will not
(hopefully) need to go through this hell as I did!
My original problem was that when after I purchased a D-Link Wireless Router
DI-624, I would get disconnected from Verizon DSL at least once every 2
hours or so. My internet access would "freeze" and then a little popup box
at the bottom right system tray would tell me that the "LAN cable has been
unplugged". After about a minute or so, my internet connection would be
back working This was NEVER happening during the 2+ years I was using my
Westell modem alone (running in router mode).
Please keep in mind: The problem I was having was not wireless related as
it was happening to the desktop computer to which the router/westell was
connected to!
During these last 8 days, I tried: one DI-624 wireless router, two Netgear
614v3 routers and two Linksys WRT54G v.2 routers. In addition, I received a
brand new Westell 2200 modem from Verizon. I also tried about four
different CAT-5 cables. Here is the final outcome:
I have the Linksys WRT54G (version 2) wireless router connected to the
Netgear Fast Ethernet FA310TX network card in Auto-Sense mode (using the
built-in XP drivers, as Netgear told me that there was never a newer
revision released). I have DISABLED the built-in 3Com Gigabit LOM (3C940)
network card (via the ASUS P4C800 Deluxe motherboard BIOS), DISABLED the
Zero Wireless Configuration service, and have put in the IP/Gateway/DNS
address numbers inside my Windows XP Network Connections | LAN setup. My
operating system is Windows XP Pro SP1 and the modem is a Westell 2200
configured as bridge only.
If my situation continues to be stable, I *might* try to go back to the 3Com
built-in card (disable any power management) and then re-enabling the Zero
Wireless Configuration services. But in reality, I am happy with the way
things are and have already spent enough time trying to get my router to
work with Verizon DSL without having it drop connections!
Now, the next step will be setting up the WIRELESS part of this. I don't
even yet have a laptop with me on the premises, but the 802.11g card that I
already have is the D-Link DWL-G650. I hope and assume that this will work
okay with the Linksys...
One thing I must say is that I never realized that how many problems other
users are having. I would have thought that since 802.11x has been around
in the mainstream by now 2+ years, that things would have been much more
"system friendlier". And again, my issues were not even WIRELESS related.
All 3 tech supports were not really helpful, as none of them realized that
the problem is somehow between the router and Windows XP (Ethernet card?)
loosing a connection, which of course results in Verizon DSL loosing the
connection also.
One other comment about the Netgear 614 v.3 router: A number of people have
responded to tell me that they have had this random "router resetting"
happen to them (where the routers behaves as if someone turned the power off
and then back on, and the lights flash) just as if you first turn it on). I
was lucky to witness it myself during one of the "disconnects" that I had.
This was actually the reason why I went back to try the Linksys one more
time. So, I would definitely recommend staying way from this 614 (version
3) model.
Once again - THANK YOU everyone!

Automatic reset problem (Palm Centro)

Recently, my phone begins to have a new problem.
When I use the phone, it automatically resets if I touch the screen during the conversation.
It disrupt my conversation.
I had done hard reset; but, the problem came up again.
What can I do?

Did the problem immediately return when you finished the Hard Reset, or after doing a HotSync? If the latter, then the problem is software-related and saved on your computer.
Did the phone get damaged in any way? Get wet?
Here's my normal help file for clearing out reset problems:
As with most problems that occur on a Palm phone or PDA, it is either software or hardware related and we have to determine which one.
Best method is to first make a complete backup of your unit to your SD card using the free "NVBackup" (available from http://www.freewarepalm.com) After the backup is complete, Hard Reset the unit, then test to see if full functionality returns.
Perform a Hard Reset as described in this Palm KB article: http://kb.palm.com/wps/portal/kb/common/article/45050_en.html
DO NOT HOTSYNC YET! Test the unit before reinstalling any software. If the unit works correctly, your problem is being caused by a "drug interaction" of software - maybe one rogue program, or a combination of several. You'll have to reinstall the third-party programs one or a few at a time to find the problem one. To avoid re-installing a software issue, rename your /Backup directory in your Palm folder (on a PC it's found here: C/Program Files/Palm(One)/"your HotSync ID name truncated"/Backup) to something like "/BackupOLD". Now perform the HotSync, choose your HotSync name you've been using, and all your PIM data will return, but not the third-party programs. Test for functionality again. If all is good, start installing the old programs from your /BackupOLD directory one (or a few if brave) at a time.
If the unit does not work after a Hard Reset is performed correctly, then it may be Hardware-related. (If it's a connection problem via either BlueTooth or Wifi, be sure nothing has changed on the unit you're trying to connect to!)
Hope this has helped,
Wyrenut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

Airport Express 1st Generation base station not showing up using new Linksys E1500 router. Compatibility problem?

Airport Utility cannot find base station. The AirPort Status Icon is showing on my iMac's menu bar, but when I click on it I do not see an AirPort option in the list --- only the various networks that are within range and the options to Create or Join a network. I have a 1st generation Airport Express (Moded A1264) and recently installed a new router, Linksys E1500. Could the router be the problem? Another computer in the house had to be set up on the router using Cisco Connect on my husband's Window's 7 computer. This was also necessary for our Wii console. When I try to use Cisco Connect to see if it needs to recognize the AirPort device, it gives me certain wireless settings necessary to connect the device (Network Name (SSID), Security key and Security Type (WPA2 or WAP). looked on the site but didn't see an option for setting up Airport Express. I also upgraded from Snow Leopard OS to Lion shortly before adding the new router. I use the Airport Express to play our Tune music on powered speakers in our kitchen and did not think to see if it was operating between the time I upgraded the operating system and the time I installed a new router. I have two different versions of AirPort Utility on the computer 6.0 and 5.6. Any suggestions?

Just spoke with Cisco about the router. They said the router is compatible with the E1500. They suggested that I contact Apple to see if their default IP address was that same as the router (192.168.1.1). They told me I would have to change it if that was the case. How would I do that?

RE: freezing and resetting problems when syncing a large music library

Hi there,
I got a new ipod classic 160gb for christmas. I updated the firmware to 1.0.3 and synced it for the first time. When I tried to play any music it locked up and went into a loop of resetting itself which I could only break by forcing the ipod into disk mode.
I restored the ipod and tried again syncing the music in chunks. This worked until the ipod was about 50% full then it started to freeze and reset again. I took this ipod back to the store but the new one had the exact same problem!
Through a lot of trial and error I have managed to get the ipod working with only part of my library synced. By syncing music a few albums at a time I have managed to get about 86gb (of 120gb) onto it, but surely this is not how it is supposed to be! I have a dual boot system and have the same problems using windows XP or vista.
I know that I'm not the only person experiencing resetting problems with the ipod classic. Are the users who are experiencing these endless resetting problems with the ipod classic those who have large music libraries (i.e over 80gb)? Can the ipod classic simply not handle the large volumes of music it was designed to hold?
The only features I was looking forward to in the new ipod were a) larger capacity hard drive and b) the ability to organise playlists into folders on the ipod for easier browsing. As it stands I cannot sync my full library and navigating through my playlists is so slow it is hardly worth bothering. I never had a minutes trouble with my 5th gen.
Have I been unlucky and the ipod classics I have recieved have been duds? In which case should I arrange another replacement? Or is this typical of the ipod classic user experience when the user has a large music library and many playlists? Should I await a firmware update that might remedy my problems?
Lastly am I doing something wrong? Any help or workarounds would be gratefully appreciated.

best thing to do is use Playlist and Smart Playliss to fill your iPod. Just so you know, since your post seemed to indicate you thought the playlists have to be tailored to what is already on the iPod, when you sync to playlists, any songs needed for those playlists are automatically moved onto the iPod. And any songs NOT in the playlists get removed.
Patrick

Does Cisco 857 router support Easy VPN?!!

Hi,
I've a Cisco 857 router with a 12.4(6)T IOS.
I want to configure it to act as an Easy VPN server, to allow my remote clients -using cisco vpn clients- to access the internal resourses behind the router.
Is it applicable with this router model?!!
thanks and regards,
Ala

Ala, upsolutely, you would probably need advance k9 security image, check at software advisory tools and slect software features for your platform.
sofware advisory
http://tools.cisco.com/Support/Fusion/FusionHome.do
857 Models See table 3 Software feature
http://www.cisco.com/en/US/prod/collateral/routers/ps380/ps6195/product_data_sheet0900aecd8028a9a9_ps380_Products_Data_Sheet.html
HTH
Rgds
Jorge

VPN between WRVS4400N and CISCO 857 router

Hi ALL,
Am trying to VPN the two and have setup the WRVS4400N side using IPSec (seems easy enough). Has anyone any experience on the 857 router side? Would you kindly show how that can be configured? Or just point me to any good source doing it will be good too. Thanks!

ip nat inside source route-map nonat interface FastEthernet0 overload
access-list 110 deny ip 10.20.10.0 0.0.0.255 10.10.10.0 0.0.0.255
access-list 110 permit ip 10.20.10.0 0.0.0.255 any
route-map nonat permit 10
match ip address 110
or better (if you have for example the IP public 1.2.3.5)
ip nat pool 1.2.3.5 1.2.3.5 1.2.3.5 prefix-length 30
ip nat inside source list nat-to-internet pool 1.2.3.5 overload
ip access-list extended nat-to-internet
deny ip 10.20.10.0 0.0.0.255 10.10.10.0 0.0.0.255
permit ip 10.20.10.0 0.0.0.255 any
deny ip any any

Modem - router getting reset for every 15 mins

My modem and router gets reset for every 15mins and every time I call Comcast not getting proper support . Can someone hear this. This happens every weekend.

freezing at regular intervals:
:http://blog.bonardo.net/2011/09/30/is-your-firefor-freezing-at-regular-intervals
: https://addons.mozilla.org/firefox/addon/places-maintenance/
Install add-on, run at least the option mentioned in the article, I ran them all. When finished you can uninstall the extension, all without taking taking Firefox down, The extension is one of the new JetPack extensions.

K8NGM2-FID warm reboot/reset problems

Hi everybody:
The system:
MSI K8NGM2-FID Bios V 3.4
RAM - G.SKILL 2GB F1-3200PHU2
Processor Athlon X2 3800+
Drive WD2500YD 250GB 7200 RPM SATA150
DVD R/W Pioneer DVR-111D
DVD-R ASUS DVD-E616AG
Case Antec Sonata II w/ Antec 450 W PSU 3.3 V/32A 12V1/15A 12V2/17A
OS WinXP SP2 w/auto update set
The Problem:
When the system runs for more than 1-2 minutes and I do a restart under Windows OR hit the reset button it hangs with the HDD light on steady and no video output.
If I try a warm restart or reset button push immediately (10-30 seconds) after windows comes up the system restarts OK.
When the system is 'hung' repeated hits (short or 5-10 seconds) on the Reset button have no effect besides causing the DVD lights to blink (i.e., they seem to be getting a reset signal) but HDD light is still steady.
If I power the system down and restart it reboots OK - this means power down from the 'hung' state OR power down from Windows via 'Start' --> 'Turn off computer' or momentary push of power switch.
Looking at the Windows system log I see that warm boots done before many system processes load are successful, those afterwards are not. I have tried disabling these processes (i.e., App layer gateway, SSDP discovery, Norton protected storage) w/o any change in behavior.
This looks like a hardware problem to me, but I want to be sure it's one before I R&R the mobo w/ a spare.
Has anybody else seen this problem?
Thanks,
ss

Update:
It was the mobo - R&R w/new one: warm boot/reset problem gone. Plugged in drives w/o doing any software reinstall and unit came right up (and down and up and down....).
This is the second K8NGM2-FID that has gone south on me since March.
Both have been Ver 2.0 builds; the other one has a problem with onboard video but continues to function with an add-in video card (yah, it's better video too, but that's not the point). The warm boot problem described in the original post isn't a show stopper, either, but I can't use these boards in a system for sale (unless I sell it to my brother-in-law).
I have built eight systems since March using the K8NGM2-FID. Six were for customers and are still under my personal six month no-questions-asked warranty (the extended 12 month lots-of-questions-asked starts after six months). I have had to eat two at this point and am not too happy with the board. Since MSI no longer makes this board I am having to use another vendor's mATX-6150 unit, perhaps for the better, I don't know.
IMHO MSI is the best board maker in the consumer/office sector. I hope they can stay that way.
ss

Can not reset router.. password problems

We have a DSL connection at home and just decided to put our Linksys router back up. I have the BEFW11s4 verson4 and when I go to my ip address and set it up my longin screen pops up and messes me up. I have tried to reset it back to factory settings and when I do that and the screen pops back up I type admin for user and password and I get the red 401 screen. I also tried to change the password on the router and that still didnt work. Then I put the CD in and I got to the last part which is make a password for the router and I get an error screen that says, Rouuter must be reset, hold the reset button for ten seconds and then contact Linksys. Whats going on its driving me nuts.. thanks for your help

While the router is on, hold the reset button for 30 seconds.
I believe holding for 10 seconds simply places the router in Bridged mode. I'm not certain about that concerning Linksys, but other manufacturers have the 10 for bridged mode rule.
Hope It Helps!
PCM 'Helping Integrate America'
Acronis Fulfillment Partner
Infrant Silver Partner
GFi Authorized Reseller
Check Point Partner
WildBlue Certified Installer

Airport Extreme (n) router keeps resetting.

My internet keeps going on and off, Ive reset to factory defaults and it keeps resetting every 10-15 minutes for a few seconds. The only thing I have changed is added 1 port forward.

I have the exact same problem and it has only been since just after the new years actually about the time the new time capsule was released it started happening I don't really want to hard wire my connection that is why I have wireless router so my Mac doesn't have to be like pc with wires coming out of it like an octopus as a caveat my time machine stopped working without warning too a few days ago??????????????HMMMMMMMMMMMMMMMMM anyone else?

857 Router Dot11Radio0 reset - problem

Similar Messages

Maybe you are looking for