AAA Authentication error

I am having trouble authenticating into my router.
Here is the debug error I get when I try to log in:
.Apr 9 18:13:15.518: AAA/BIND(00000068): Bind i/f
.Apr 9 18:13:15.522: AAA/AUTHEN/LOGIN (00000068): Pick method list 'default'
.Apr 9 18:13:15.522: TPLUS: Queuing AAA Authentication request 104 for processing
.Apr 9 18:13:15.522: TPLUS: processing authentication start request id 104
.Apr 9 18:13:15.522: TPLUS: Authentication start packet created for 104(david)
.Apr 9 18:13:15.522: TPLUS: Using server 172.16.6.3
.Apr 9 18:13:15.522: TPLUS(00000068)/1/NB_WAIT/4620496C: Started 60 sec timeout
.Apr 9 18:13:15.522: TPLUS(00000068)/1/NB_WAIT: socket event 2
.Apr 9 18:13:15.526: TPLUS(00000068)/1/NB_WAIT: wrote entire 42 bytes request
.Apr 9 18:13:15.526: TPLUS(00000068)/1/READ: socket event 1
.Apr 9 18:13:15.526: TPLUS(00000068)/1/READ: Would block while reading
.Apr 9 18:13:15.658: TPLUS(00000068)/1/READ: socket event 1
.Apr 9 18:13:15.658: TPLUS(00000068)/1/READ: errno 254
.Apr 9 18:13:15.658: TPLUS(00000068)/1/4620496C: Processing the reply packet
.Apr 9 18:13:20.434: AAA/AUTHEN/LOGIN (00000000): Pick method list 'default'
.Apr 9 18:13:20.434: TPLUS: Queuing AAA Authentication request 0 for processing
.Apr 9 18:13:20.434: TPLUS: processing authentication start request id 0
.Apr 9 18:13:20.434: TPLUS: Authentication start packet created for 0(david)
.Apr 9 18:13:20.434: TPLUS: Using server 172.16.6.3
.Apr 9 18:13:20.434: TPLUS(00000000)/1/NB_WAIT/4620496C: Started 60 sec timeout
.Apr 9 18:13:20.434: TPLUS(00000000)/1/NB_WAIT: socket event 2
.Apr 9 18:13:20.438: TPLUS(00000000)/1/NB_WAIT: wrote entire 25 bytes request
.Apr 9 18:13:20.438: TPLUS(00000000)/1/READ: socket event 1
.Apr 9 18:13:20.438: TPLUS(00000000)/1/READ: Would block while reading
.Apr 9 18:13:20.438: TPLUS(00000000)/1/READ: socket event 1
.Apr 9 18:13:20.438: TPLUS(00000000)/1/READ: errno 254
.Apr 9 18:13:20.438: TPLUS(00000000)/1/4620496C: Processing the reply packet
Any help would be greatly apperciated.

David
The debugs show that you are sending requests to ACS/TACACS and receiving no response. There are several things that could cause this symptom. First you should check on whether the request is getting to the TACACS server. Probably you could look in the logs of the server and see if it has recognized and processed requests from your device. If it recognized the request then it may also have some indication of why it did not authenticate. These causes could include a mismatch in the shared key, the server does not have a correct definition of this device as a TACACS client, your machine is not sending requests with the source address that the TACACS server is expecting.
You also might want to verify that there is correct IP connectivity from your router to the TACACS server (ping or extended ping is a good way to check this). You might also check along the path and make sure that there are not access lists which might be blocking your request (or blocking the response from the server back to you).
HTH
Rick

Similar Messages

RADIUS Authentication Error Across the Subnet

Hi Guyz
I have configured Microsoft Server 2012 R2 as a RADIUS for Cisco IOS Devices
Server IP Address : 10.95.6.12
Router IP Address Fa 0/0.192 ---->>> 192.193.194.195
Router IP Address Fa 0/0.6 --->>> 10.95.6.1
Switch IP Address VLAN 192    ---->>> 192.193.194.2010.95.6.11
Switch IP Address VLAN 6 ---->>> 10.95.6.11
When i access the Cisco Devices RADIUS CLIENT with 10.95.6.x Subnet, It works fine
When i access the Cisco Devices through RADIUS CLIENT 192.193.194.x Subnet, It does not pass through the RADIUS Authentication.
Attached in the Picture i can not access the 192.193.194.20 Device but I can access 10.95.6.1 Device. As soon as I change the IP Address 10.95.6.11 I can access the Device.
Ping is successful across the Routers / Switches and Server as well. Below is unsuccessful debug details as well:
===
Home_Switch#
01:52:30: RADIUS/ENCODE(00000008): ask "Password: "
Home_Switch#
01:52:41: RADIUS/ENCODE(00000008):Orig. component type = EXEC
01:52:41: RADIUS: AAA Unsupported Attr: interface [171] 4
01:52:41: RADIUS: 74 74 [ tt]
01:52:41: RADIUS/ENCODE(00000008): dropping service type, "radius-server attribute 6 on-for-login-auth" is off
01:52:41: RADIUS(00000008): Config NAS IP: 0.0.0.0
01:52:41: RADIUS/ENCODE(00000008): acct_session_id: 8
01:52:41: RADIUS(00000008): sending
01:52:41: RADIUS/ENCODE: Best Local IP-Address 10.95.6.11 for Radius-Server 10.95.6.12
01:52:41: RADIUS(00000008): Send Access-Request to 10.95.6.12:1812 id 1645/6, len 85
Home_Switch#
01:52:41: RADIUS: authenticator 95 FB 3F FE 79 BB AA D6 - C9 26 F4 EC 95 32 80 06
01:52:41: RADIUS: User-Name [1] 7 "cisco"
01:52:41: RADIUS: User-Password [2] 18 *
01:52:41: RADIUS: NAS-Port [5] 6 2
01:52:41: RADIUS: NAS-Port-Id [87] 6 "tty2"
01:52:41: RADIUS: NAS-Port-Type [61] 6 Virtual [5]
01:52:41: RADIUS: Calling-Station-Id [31] 16 "192.193.194.50"
01:52:41: RADIUS: NAS-IP-Address [4] 6 10.95.6.11
01:52:41: RADIUS(00000008): Started 5 sec timeout
Home_Switch#
01:52:46: RADIUS(00000008): Request timed out
01:52:46: RADIUS: Retransmit to (10.95.6.12:1812,1813) for id 1645/6
01:52:46: RADIUS(00000008): Started 5 sec timeout
Home_Switch#
===
Any help will really appreciate.

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154866/radius-authentication-error-across-subnet

AAA authentication is fail on cisco 4505 switch with acs

i am new in AAA . i want to login switch which authentication come from cisco acs 5.1 but i configure both switch and acs 5.1. when i telnet
switch it display % Authentication fails. can anybody help me regurding this issue!!!
on cisco switch end conf:
aaa new-modle
aaa authentication login default group tacacs+
aaa authentication login TACASE group tacacs+
aaa authentication exec default group tacacs+
tacacs-server host 10.10.10.1
tacacs-server key Password!@#
line vty 0 4
login authentication TACASE
on acs 5.1 side i add switch on its vlan ip address which is connect acs 5.1 but
BUT when i login using putty terminal its show % Authentication fails.
Please help me regurding this issue!!!

Hi,
what is the error message reported on ACS?
Are you sure that you are using the same key on ACS and cat4k?
Can you configure "ip tacacs source-interface " with the vlan interface you are using as source?
You can also collect these debugs:
- deb aaa authentication
- deb tacacs
Cheers
Marco

Help in command aaa authentication

Hi,
Could someone explain this command
aaa authentication login default
what does the authentication default to when we are not providing any authentication such as local or group radius.
Thanks
Jason

Hi Jason,
This command would generate a error such as :-
R(config)#aaa authentication login default
% Incomplete command.
we need to specify an auth method.
Regards,
Vivek

ACE 4700 and Cisco ACS aaa authentication

ACE version Software
loader: Version 0.95
system: Version A1(7b) [build 3.0(0)A1(7b)
Cisco ACS version 4.0.1
I am trying to authenticate admin users with AAA authentication for ACE management.
This is what I've done:
ACE-lab/Admin(config)# tacacs-server host 192.168.3.10 key 123456 port 49
warning: numeric key will not be encrypted
ACE-lab/Admin(config)# aaa group server tacacs+ cciesec
ACE-lab/Admin(config-tacacs+)# server ?
<A.B.C.D> TACACS+ server name
ACE-lab/Admin(config-tacacs+)# server 192.168.3.10
can not find the TACACS+ server
specified TACACS+ server not found, please configure it using tacacs-server host ... and then retry
ACE-lab/Admin(config-tacacs+)#
Why am I getting this error? I have full
connectivity between the ACE and the ACS
server. Furthermore, the ACS server
works fine with other Cisco IOS devices.
Please help. Thanks.

Thanks. Now I have another problem. I CAN
log into the ACE via tacacs+ account(s).
However, I get error when I try going into
configuration mode:
ACE-lab login: ngx1
Password:
Cisco Application Control Software (ACSW)
TAC support: http://www.cisco.com/tac
Copyright (c) 1985-2007 by Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
ACE-lab/Admin# conf t
^
% invalid command detected at '^' marker.
ACE-lab/Admin#
The ngx1 account can access other Cisco
routers/switches just fine and can go into
enable mode just fine. Only issue on the ACE.
Any ideas? Thanks.

Cisco AAA authentication with windows radius server

Cisco - Windows Radius problems
I need to created a limited access group through radius that I can have new network analysts log into
and not be able to commit changes or get into global config.
Here are my current radius settings
aaa new-model
aaa group server radius IAS
server name something.corp
aaa authentication login USERS local group IAS
aaa authorization exec USERS local group IAS
radius server something.corp
address ipv4 1.1.1.1 auth-port 1812 acct-port 1813
key mypassword
line vty 0 4
access-class 1 in
exec-timeout 0 0
authorization exec USERS
logging synchronous
login authentication USERS
transport input ssh
When I log in to the switch, the radius server is passing the corrrect attriubute
***Jan 21 13:59:51.897: RADIUS:   Cisco AVpair       [1]   18 "shell:priv-lvl=7"
The switch is accepting it and putting you in the correct priv level.
***Radius-Test#sh priv
   Current privilege level is 7
I am not sure why it logs you in with the prompt for privileged EXEC mode when
you are in priv level 7. This shows that even though it looks like your in priv exec
mode, you are not.
***Radius-Test#sh run
                ^
   % Invalid input detected at '^' marker.
   Radius-Test#
Now this is where I am very lost.
I am in priv level 7, but as soon as I use the enable command It moves me up to 15, and that gives me access to
global config mode.
***Radius-Test#enable
   Radius-Test#
Debug log -
Jan 21 14:06:28.689: AAA/MEMORY: free_user (0x2B46E268) user='reynni10'
ruser='NULL' port='tty390' rem_addr='10.100.158.83' authen_type=ASCII service=ENABLE priv=15 vrf= (id=0)
Now it doesnt matter that I was given priv level 7 by radius because 'enable' put me into priv 15
***Radius-Test#sh priv
   Current privilege level is 15
   Radius-Test#
I have tried to set
***privilege exec level 15 enable
It works and I am no longer able to use 'enable' when I am at prv level 7, but I also cannot get the commands they will need to work.
Even if I try to do
***privilege exec level 7 show running-config (or other variations)
It will allow you to type sh run without errors, but it doest actually run the command.
What am I doing wrong?
I also want to get PKI working with radius.

I can run a test on my radius system, will report back accordingly, as it's a different server than where I am currently located.
Troubleshooting, have you deleted the certificate/network profile on the devices and started from scratch?

AAA authentication not working and 'default' method list

Guys,
I hope someone can help me here in troubleshooting AAA issue. I have copied configuration and debug below. The router keeps using local username/password even though ACS servers are reachable and working. From debugs it seems it keeps using 'default' method list ignoring TACACS config. Any help will be appreciated
Config
aaa new-model
username admin privilege 15 secret 5 xxxxxxxxxx.
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization console
aaa authorization exec default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
aaa authorization reverse-access default group tacacs+ local
aaa accounting commands 0 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
aaa session-id common
tacacs-server host x.x.x.x
tacacs-server host x.x.x.x
tacacs-server host x.x.x.x
tacacs-server host x.x.x.x
tacacs-server directed-request
tacacs-server key 7 0006140E54xxxxxxxxxx
ip tacacs source-interface Vlan200
Debugs
002344: Dec 5 01:36:03.087 ICT: AAA/BIND(00000022): Bind i/f
002345: Dec 5 01:36:03.087 ICT: AAA/AUTHEN/LOGIN (00000022): Pick method list 'default'
002346: Dec 5 01:36:11.080 ICT: AAA/AUTHEN/LOGIN (00000022): Pick method list 'default'
core01#
002347: Dec 5 01:36:59.404 ICT: AAA: parse name=tty0 idb type=-1 tty=-1
002348: Dec 5 01:36:59.404 ICT: AAA: name=tty0 flags=0x11 type=4 shelf=0 slot=0 adapter=0 port=0 channel=0
002349: Dec 5 01:36:59.404 ICT: AAA/MEMORY: create_user (0x6526934) user='admin' ruser='core01' ds0=0 port='tty0' rem_addr='async' authen_type=ASCII service=NONE priv=15 initial_task_id='0', vrf= (id=0)
002350: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): Port='tty0' list='' service=CMD
002351: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/CMD: tty0 (2162495688) user='admin'
002352: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send AV service=shell
002353: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send AV cmd=configure
002354: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send AV cmd-arg=terminal
002355: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): send AV cmd-arg=<cr>
002356: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): found list "default"
002357: Dec 5 01:36:59.404 ICT: tty0 AAA/AUTHOR/CMD (2162495688): Method=tacacs+ (tacacs+)
002358: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC+: (2162495688): user=admin
002359: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC+: (2162495688): send AV service=shell
002360: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC+: (2162495688): send AV cmd=configure
002361: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC+: (2162495688): send AV cmd-arg=terminal
002362: Dec 5 01:36:59.404 ICT: AAA/AUTHOR/TAC+: (2162495688): send AV cmd-arg=<cr>
Enter configuration commands, one per line. End with CNTL/Z.
core01(config)#
002363: Dec 5 01:37:04.261 ICT: AAA/AUTHOR (2162495688): Post authorization status = ERROR
002364: Dec 5 01:37:04.261 ICT: tty0 AAA/AUTHOR/CMD (2162495688): Method=LOCAL
002365: Dec 5 01:37:04.261 ICT: AAA/AUTHOR (2162495688): Post authorization status = PASS_ADD
002366: Dec 5 01:37:04.261 ICT: AAA/MEMORY: free_user (0x6526934) user='admin' ruser='core01' port='tty0' rem_addr='async' authen_type=ASCII service=NONE priv=15
core01(config)#

Are the tacacs+ servers reachable using the source vlan 200. Also in the tacacs+ server can you check if the IP address for this device is correctly configured and also please check the pwd on both the server and this device match.
As rick suggested sh tacacs would be good as well. That would show failures and successes
HTH
Kishore

How to fix authentic error in game centre of iPad mini?

How to fix authentic error in game centre of iPad mini?

Following further research, this keyboard lag issue appears to be related to the (botched) iOS 7.1 update. It's good to know I am not the only user who had his iPad mini rendered unusuable by the iOS 7.1 update, however that does not solve my problem.
Anyone out there who has further suggestions (except doing a factory reset via iTunes)?

Remote Desktop Connection - Authentication error

Hello,
I wish to connect to my work PC from my laptop. The remote desktop connection was working fine till yesterday, but today i receive the following error when i try to connect -
"An authentication error has occurred. The Local Security Authority cannot be contacted. Remote Computer: <name>."
I have Win 7 ultimate installed on my 32 bit system, and have tried solutions proposed in the other threads. I do not require a NLA check for connection, i have always used the remote desktop with this option unchecked. Could anyone help me with this please?
Is this a error on my Laptop, or do i need to contact the network administrators for this?

Hi!
It could be as easy as you need to change your password on your domain accout.
Are both computers connected to the same domian or is your work computer connected to a domain and your laptop connected to a workgroup?
If your password has expired, this error can occur, so I would start to check that since it stoped working over night.
Best regards
Andreas Molin

Query: Authentication Error while consuming a web service

Hi All,
I've generted a WSDL file by using the following steps.
1.Created a RFC enabled ABAP pgm
2.Created a web service out of it (using webservice creation wizard - default virtual host. so my port is 8100)3.Released the web service (WSCONFIG)
4.Generated the WSDL file (WSADMIN + CTRL F1).
Then I wanted to consume it from a .Net program. But am getting authentication error in .Net.
Do I need to configure anything for Authentication (username and password) from R/3 side?..
How Do I pass the credential info from .Net?.
Should I take care of any setup other than what I've specified?.
Any Blogs or response would be appreciated.
Thanks,
Joe.

Usually like this:
WSReference1.WSPProxy proxy = new WSReference1.WSPProxy();
proxy.Credentials = new System.Net.NetworkCredentials("Username", "Password");
proxy.PreAuthenticate = true;
proxy.CallMethod();

Client Authentication error while invoking portal web service.

Hi All,
I have created a java portal web service from portal service using NWDS, I am getting client authentication error while invoking the service.
Please tell me where to enter client authenticity details.
regards
Santosh

hi,
check whether you have the UME permissions for accessing this webservice.
Rdgs,
Guru

Authentication Error while Configue SOA in JDev 11g TP4

Hi everyone.
I'm trying to configure SOA suite 11g in my local system. I have done the schema creation and already created a App server connection in JDev->Tools-> Java EE Runtime Preferences.
When I start the configue SOA, it failes to start or stop the oc4j instance as below phase:
[echo] Changing oc4j ports with following values:
HTTP Port : 8988 -> 8888
RMI Port : 23891 -> 12401
RMI SSL Port: 24043 -> 24043
JMS Port : 9227 -> 12601
[echo] Create jms queues/topics from new oc4j jms template
[echo] Changing jms.xml to use port : 12601
[echo]
* Configuring SOA Infrastructure. This will take 5-10 minutes. *
* Summary of SOA configuration parameters: *
** Oracle Home = F:\jdeveloper11g\
** Oracle Instance = F:\jdevinstance\system11.1.1.0.22.49.49
** SOA Database = localhost:1521:XE
** SOA Database User = jdev_soainfra
** HTTP Port = 8888
** RMI Port = 12401
** JMS Port = 12601
** Component Type = o.j2ee
** Component Name = embedded-oc4j
** Configure OWSM = false
** Configure SOA Console = true
** Configure B2B UI = false
** Configure XEngine = false
[echo] ==Stopping oc4j standalone...
[exec] Result: 1
[echo] ==Waiting max 240 second(s) for shutdown of URL http://ESFANDIYAR:8888...
BUILD FAILED
F:\jdeveloper11g\install\bpel\build.xml:10: The following error occurred while executing this line:
F:\jdeveloper11g\install\bpel\soa-infra-config.xml:48: The following error occurred while executing this line:
F:\jdeveloper11g\install\bpel\soa-infra-config.xml:89: ***************************************************
* Configuring SOA Infrastructure has FAILED.
* If following log files exists, please check them for possible cause:
* F:\jdevinstance\system11.1.1.0.22.49.49\o.j2ee\embedded-oc4j\install\tmp\soa-infra-java.log
* F:\jdevinstance\system11.1.1.0.22.49.49\o.j2ee\embedded-oc4j\log\startsoa.log
Total time: 4 minutes 23 seconds
I checked the log file and it says it is encountered an authentication error. I'm wondering which user name and password it is referring and where shall I set the correct values. During the app server connection, I have entered the proper value for oc4jadmin/password.
Aug 30, 2008 11:37:00 PM oracle.j2ee.util.AnnotatedLogger logWithThrowable
WARNING: J2EE JNDI-00005
Authentication failed when trying to connect to the server. You need to provide a valid username and password.
Caused by:class javax.naming.AuthenticationException: Not authorized
oracle.oc4j.admin.deploy.cmdline.AdminCommandException:
Failed to connect to the server with deployment URI (deployer:oc4j:ESFANDIYAR:12401). Please refer to the exception trace from server above to identify the cause.
     at oracle.oc4j.admin.deploy.cmdline.AdminCommandBase.execute(AdminCommandBase.java:54)
     at oracle.oc4j.admin.deploy.cmdline.Oc4jAdminCmdline.executeCommand(Oc4jAdminCmdline.java:107)
     at oracle.oc4j.admin.deploy.cmdline.Oc4jAdminCmdline.main(Oc4jAdminCmdline.java:71)
Thanks for any help.
Esfand

Hi Heidi,
I tried once again to install a fresh instance of Oracle soa suite 10.1.3.0 and upgraded it to 10.1.3.4 successfully. I did all the JDeveloper 11g installation and configure SOA process all successfully. I can create a connection to OC4J using 12401 RMI port successfully but none of my applications are deployed to server.
This message is repeatedly displaying in messages tab:
Exception returned by remote server: com.evermind.server.rmi.RMIConnectionException: Disconnected: oracle.oc4j.admin.management.shared.SharedModuleType. local class incompatible during deploy ...
The default OC4J RMI port is 23791 but in my installation it is set to 12401 when I checked the Runtime Port option of Oracle Application Server and the connection is fine with this port but applications can not be deployed with this configuration.
I can deploy applications on separate standalone OC4J instance successfully but not able to do it with my SOA application server.
Any comments will be appreciated.
Thanks again
Esfand
Edited by: user3788199 on Sep 8, 2008 6:50 AM

Authentication Error while Sending Email from SMTP server.

Authentication Error while Sending Email from SMTP server. Can receive emails but cannot send emails from this account.

no email account was setup on the phone unless it was issued by your company.
gmail is required but no server address ports to enter.
my gmail account was setup before i took delivery of the phone but could have been done when phone was activated.
i added cox pop3 email and had to manually enter both pop3 and smtp servers with both boxes checked on both servers.
i doubt if it's a verizon issue.

Remote Desktop Connection Authentication Error from Windows 8.1 Pro to Windows 7 Pro

I keep trying to connect to my server running Windows 7 Pro from my laptop running Windows 8.1 Pro, but I get the following message after providing
my credentials:
"An authentication error has occurred (Code: 0x8007001f)"
I can't find any reference to this error code being associated with using remote desktop.

Hello,
Are you connecting to a server as part of a domain ? if so confirm you are using adequate credentials for remote desktop for example: username: domain\administrator
if not you can try connecting to the localhost using:
username: .\administrator - for example
also you can try running your remote connection in admin mode:
Win + R - bring up run then type:
mstsc /admin
hope that helps.
Cheers,
Harry

Oracle BI Portlet -Authentication Error in WebSphere Portal

We have deployed the oracle BI Portlet in WebSphere Portal Server.
We have made necessary changes in the portlet.xml and created the credential vault to store user information as well .
Our WebSpere Portal is integrated with LDAP Server .
When the Portal Admin logs in he can see the reports in Oracle BI Portlet ......however a non admin user gets the following error message.
Authentication error. Details: An invalid User Name or Password was entered.
Can someone plz help.

Hi
I am trying to integrate OBIEE 10.1.3.4.1 with Websphere Portal.
I perform following steps :
1. Installed OBIEE and created a report at url "http://punitp63969d:9704/analytics/saw.dll?Dashboard"
2. Modified portlet.xml of sawjsr168portlets.war as follows
<preference>
<name>oracle.bi.presentation.sawserver.URL</name>
<value>http://punitp63969d:9704/analytics/saw.dll?Dashboard</value>
<read-only>false</read-only>
</preference>
<preference>
<name>oracle.bi.presentation.portlets.jsr168.reportui.AdminUserName</name>
<value>Administrator</value>
<read-only>false</read-only>
</preference>
<preference>
<name>oracle.bi.presentation.portlets.jsr168.reportui.AdminPwd</name>
<value>Administrator</value>
<read-only>false</read-only>
</preference>
<preference>
<name>oracle.bi.presentation.portlets.websphere.SuperuserSlotId</name>
<value>sawseveradmin</value>
<read-only>false</read-only>
</preference>
where Administrator/Administrator is user-id/password for OBIEE and
sawseveradmin is name of credential vault in WebSphere-Portal.
3. Deployed the war on WebSphere Portal and got portlet disable with following error in log :
WSVR0200I: Starting application: PA_SAWReport
9/4/09 18:42:52:067 IST 000001ff ApplicationMg A WSVR0204I: Application: PA_SAWReport Application build level: Unknown
9/4/09 18:42:52:708 IST 000001ff WebGroup A SRVE0169I: Loading Web Module: SAWReport.
9/4/09 18:42:52:973 IST 000001ff VirtualHost I SRVE0250I: Web Module SAWReport has been bound to default_host:10000,:80,:10002,:10015,:10016,:443,:10023,:10026,:10040,:10035.
9/4/09 18:42:53:130 IST 000001ff ApplicationMg A WSVR0221I: Application started: PA_SAWReport
9/4/09 18:42:59:692 IST 00000037 WebContainer E SRVE0255E: A WebGroup/Virtual Host to handle /searchfeed/myserver/scopes has not been defined.
9/4/09 18:43:26:458 IST 00000037 WebContainer E SRVE0255E: A WebGroup/Virtual Host to handle /searchfeed/myserver/scopes has not been defined.
9/4/09 18:43:50:318 IST 000000a5 ServletWrappe I SRVE0242I: PA_SAWReport [wps/PA_SAWReport] Oracle_Business_Intelligence_Report_View_Portlet: Initialization successful.
9/4/09 18:43:50:521 IST 000000a5 MimeResponseI E com.ibm.ws.portletcontainer.core.impl.MimeResponseImpl getWriter EJPPC0176W: Invalid content type
9/4/09 18:43:50:661 IST 000000a5 ServletWrappe E SRVE0068E: Uncaught exception thrown in one of the service methods of the servlet: Oracle_Business_Intelligence_Report_View_Portlet. Exception thrown : javax.servlet.ServletException: java.lang.IllegalStateException: No content type set.
at com.ibm.ws.portletcontainer.invoker.impl.PortletServlet.doDispatch(PortletServlet.java:369)
Caused by: java.lang.IllegalStateException: No content type set.
     at com.ibm.ws.portletcontainer.core.impl.MimeResponseImpl.getWriter(MimeResponseImpl.java:114)
     at com.siebel.analytics.web.portlets.jsr168.ReportUI.checkUser(ReportUI.java:852)
     at com.siebel.analytics.web.portlets.jsr168.ReportUI.doView(ReportUI.java:167)
     at javax.portlet.GenericPortlet.doDispatch(GenericPortlet.java:328)
     at com.siebel.analytics.web.portlets.jsr168.ReportUI.doDispatch(ReportUI.java:1058)
     at javax.portlet.GenericPortlet.render(GenericPortlet.java:233)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletFilterChainImpl.doFilter(PortletFilterChainImpl.java:128)
     at com.ibm.wps.propertybroker.standard.filter.C2APortletFilter.doFilter(C2APortletFilter.java:185)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletFilterChainImpl.doFilter(PortletFilterChainImpl.java:120)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServlet.doDispatch(PortletServlet.java:573)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServletCollaboratorChainImpl.doCollaborator(PortletServletCollaboratorChainImpl.java:114)
     at com.ibm.isclite.container.collaborator.PortletServletCollaborator.doRender(PortletServletCollaborator.java:68)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServletCollaboratorChainImpl.doCollaborator(PortletServletCollaboratorChainImpl.java:105)
     at com.ibm.ws.portletcontainer.rrd.RRDServerPortletServletCollaborator.doRender(RRDServerPortletServletCollaborator.java:123)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServletCollaboratorChainImpl.doCollaborator(PortletServletCollaboratorChainImpl.java:105)
     at com.ibm.ws.portletcontainer.cache.CacheCollaborator.doRender(CacheCollaborator.java:92)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServletCollaboratorChainImpl.doCollaborator(PortletServletCollaboratorChainImpl.java:105)
     at com.ibm.wps.pe.pc.waspc.core.impl.PortletServletCollaboratorImpl.doRender(PortletServletCollaboratorImpl.java:156)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServletCollaboratorChainImpl.doCollaborator(PortletServletCollaboratorChainImpl.java:105)
     at com.ibm.ws.portletcontainer.invoker.impl.PortletServlet.doDispatch(PortletServlet.java:273)
     ... 219 more
Please help me resolve this issue.Thanks in advance.

AAA Authentication error

Similar Messages

Maybe you are looking for