About installation of PCI-6024E!

I have a PCI-6024E card.After I installed the NI-DAQ version 6.9.3,I plug PCI-6024E card into the PCI slot of computer.But Measurement and Automation didn't find it in the "Devices and Interfaces".Then I pluged PCI-6024E card into different slot,the result was same.Could you please help me how to slove this problem?By the way,my operation system is windows 2000.I tried all troubleshooting method that on NI's website to improve this problem,but I failed.Please advise me some suggestion.Your soonest reply will be much appreciated.

1) The option you speak about is used to check if there are new driver versions for the products you use. The one I mentionned is not the same. You can access it through the last line of the same menu. It allows you to define whether MAX updates the list of the installed products on your demand or automatically. If the first option is checked, you must press F5 to update the display of MAX.
2) Your card may be defective.
- Was it detected by the operating system after the installation ?
- Does it appear in the list of the installed peripherals (Control Panel --> System --> ...) ? (As mentionned before I unfortunately don't remember the exact terms because I have been using french versions for a long time).
- Do you have another car
d to check ?
3) No problem with the driver version.

Similar Messages

  • Noise in thermocouple measurement using PCI-6024E DAQ card

    I am using a PCI-6024E DAQ card for thermocouple(TC) measurement. The
    TC is installed in the mold cavity of an injection molding (IM)
    machine. The leads from the TC are connected to the DAQ card using a
    CB-68LP board. I made a  temperature mesurment task in LabView 7.0
    with the two leads from TC as differential inputs and used CJC value of
    25 deg C.
    The problem is that when the IM machine is OFF, I get a reasonable temp
    reading with some slight noise but as soon as I turn ON the IM machine,
    the temp readings go wild with a lot of variations around the mean
    value. The temp values also don't go to higher values when the TC is in
    contact with the molten plastic in the IM machine.
    Do I need to ground something here or put a resistor in the I/O board?
    BTW the IM machine is grounded and the TC give correct temp values when
    connected to a hand-held temp reader.
    Any help will be highly appreciated.

    Hello  Aftab,
    Looks like you need to use bias resistors to reduce the noise. Check out the following tutorial for more information about how to use bias resistors.

  • Run 2 PCI 6024E in parallel -- Dirty signals

    Hi everyone,
    I have two PCI-6024E Cards in my system. I want to run them parallel in continuous acquisition mode (I need to monitor 12 channels in differential mode).
    The VI works like this:
    Two tasks are configured for continuous acquisition (Device 1 and 2). In a following while-loop I read a certain number of samples from both devices, do some calculations, and write an extract (2 Vals) to a log file. Loop starts over.
    The problem:
    When doing so I have false measurements 3 to 4 times a second. Strength about 70% of my input range.
    Things I did so far:
    Checking the circuitry by using an analog data recorder. Result: clean signal
    Checking the channels in MAX (test feature). clean signals
    If anyone has any suggestions they would be greatly appreciated
    Peter
    p.s. I attached a copy of the code
    Attachments:
    _BehrLogDevZone.llb ‏146 KB

    Hello Peter,
    first you should insert an error cluster to display the error (inside and outside from the while loop).
    Then you should reduce the amount of data for example from 600.000 to 6.000.
    You have 12 Channels with 600.000 values per channel and you save double values.
    The function "Save Data" needs a lot of time.
    You should try to open the file before you jump into the while loop.
    In the while loop follows the write function and outside from the while loop the close function.

  • Want to simulate a PCI-6024E

    I would like to use NI-DAQmx to simulate a PCI-6024E for developing code on my PC which does not contain this acquisition card (or any other DAQ card).
    I just finished installing NI-DAQ 7.4, with MAX 3.1.1.3004. In MAX, I right-click "Devices and Interfaces", then select "Create New", then "NI-DAQmx Simulated Device". The dialog box that appears will only allow me to simulate devices for SCXI, SCC, TEDS, or RTSI.
    Is there a way to simulate an acquisition card such as the PCI-6024E? How can I obtain this option?

    I'm not sure what is different between your installation and mine, (I'm also running MAX 3.1.1.3004) but when I check on a machine with NI-DAQ 7.4, when I "right click" in MAX on NI_DAQmx devices it presents me with a menu that has as a selection NIDAQmx simulated device. When I select that it gives me another menu with a tree menu with what appears to be most of the current device types (M series DAQ, E series DAQ, etc.) It sounds like you may not have a complete installation, some how. Was yours "two cd's" worth? One is supposedly the 7.4, the other drivers.
    Good Luck,
    Putnam Monroe
    Putnam
    Certified LabVIEW Developer
    Senior Test Engineer
    Currently using LV 6.1-LabVIEW 2012, RT8.5
    LabVIEW Champion

  • How to reduce reading and recording data time/ Visual C++, PCI 6024E and PCI-MIO-16E?

    Right now I am working on a data communication programme. The time of reading digital signal and recording data is more than I expected, which is about 100 microsecond. I need to reduce the time. The software I am using is Visual C++ 6.0. I use two DAQ boards, which are PCI-6024E and PCI-MIO-16E. I have set the priority of Visual C++ to be realtime by task manager. The operating systme is Windows XP.
    I am wondering how to set the interrupt of reading or writing data to be the highest and stop any other kind of interrupt.
    Thanks in advance!

    The primary limitation you will encounter when trying to do high speed
    digital I/O using your E-Series hardware is that the digital lines are
    all software timed.  This means that for each and every digital
    read it is necessary for your software to issue a command to your
    hardware, read a single point, then receive the response from the
    board.  This prevents you from performing digital operations at
    very high speed.  In general, I would say that 100 microseconds is
    a very good response using software-timed digital I/O on a Windows
    computer.
    It is difficult to make a good recommendation without more detail about
    what you are trying to do.  You may need to consider switching to
    a Real-Time operating system, or upgrading your DAQ hardware to a board
    that will allow you to time your digital acquisitions on the board
    itself.  These devices, such as the m-Series DAQ or the PCI-653x
    series, would allow you to use hardware triggers for your digital
    acquisitions, change detection, and buffered data acquisitions to
    reduce the software overhead involved in a rapid acquisition.

  • PCI -6024E and RDA of NI-DAQ 7.1

    The PCI-6024E on a remote computer under Win98. NI-DAQ 7.1. NI-MAX on the remote mashine shows that everything works fine, no problems.
    On the client computer under WinXP. The same Software.In NI-MAX, Everything is available except "Output Mode" in Analog Output Tab of Test Panel. This feature is disabled.
    Also non of the examples related to Continuous Input do not work. Is it normal for the latest NI-DAQ?

    We have tracked down the issue and are working on a fix. The problem has to do with the nirpc.dll shared library that gets included with the NI-DAQ 7.1 installer. Version 3.1.0f0 contains a bug such that calling AI Buffer Read.vi where (number of scans to read * number of channels > 1000) will result in a hang in WinXP, or possibly a crash on other operating systems.
    There are a couple of ways to work around this problem until we have an official fix:
    1) Always keep (number of scans to read * number of channels <= 1000)
    or
    2) On the server computer, use the version of nirpc.dll that shipped with NI-DAQ 7.0.1. (It is not necessary to update the client machine). To do this, you need to copy the following DLLs into you
    r system directory:
    nirpc.dll
    nilpcsoc.dll
    If you choose #2, then you should back up the installed version of nirpc.dll, and make sure to reinstate the original version before running any newer NI-DAQ installers in the future (this will ensure that the installers upgrade all the files properly).
    Good luck,
    Joe

  • I have trouble finding the drivers to install a PCI-6024E data acquisition device.

    I can't find which drivers I should get to install a PCI-6024E data acquisition device. I had NI-DAQ 7.1 and I just upgraded to version 7.2, but it still doesn't work. From what I read, this is a plug-and-play device, so, if the drivers are in my computer, Windows XP should be able to complete the installation without any problems; we have a PCI-6110, which was re-installed correctly.
    Any help would be greatly appreciated.

    Hello,
    NI-DAQ is the correct driver for the PCI-6024E and PCI-6110 devices. Since you have two devices, you should try a combination of installations to see if you can narrow down the problem to a possible damaged board.
    What I mean by this is the following:
    Install the 6110. If it works, pull the device and plug the 6024E into the same PCI slot and see if it works. If it does not, then you may want to consider calling National Instruments at 866-275-6964 and requesting a Return Material Authorization to get your device repaired. If you call in, you will probably be asked to go through a few more troubleshooting steps with an Applications Engineer to try and determine exactly what it is that might need to be repaired.
    If it does work after perfoming th
    e above test, post back to his discussion so we can troubleshoot further.
    Jared A

  • DAQ using PCI-6024E

    I am new to labview and am conducting a project where i have to aquire data and analyze it using labview and a PCI-6024E board (with a CB-68LPR connecter block)
    Could I get a list of the pinouts for this board or are they the same as 68pin MIO I/O pinouts?
    Also any information about how to set up channels would be helpful

    Go to the following folder on you hard drive
    C:\Program Files\National Instruments\NI-DAQ\Docs\TradDAQ_Device_Pinouts.chm
    I do beleive looking at this document that since it's an E series board that it uses
    the 68-Pin MIO I/O Connector Pinout

  • Doubt about installation SAP NETWEAVER AS ABAP 7.03 TRIAL VERSION

    Hey guys,   I need a help about installation SAP NETWEAVER AS ABAP 7.03 64 TRIAL. During installation I got the question informed on the image below. What do I have to do in this part?

    Hi Andreas,
    I dont have an Export DVD of Netweaver 7.00 EHP3. I just downloaded the application from SDN and I got this files (IMAGE) after descompressed.
    I started the installation from beginning. This is not an upgrade of system. Its my first time that I install this application.
    please look at the pictures. I tried this path. What is missing?

  • How do i generate the TTL pulse from PCI 6024E DAQ card

    Hi, I'm trying to write a program which generates a single TTL pulse when it is run. My goal is to generate the pulse, send it to the output channel of my PCI 6024E DAQ card, and then use a BNC cable, to display the signal on the oscilloscope. I have written the code and I think it appears fine but when I try to view the signal on the scope I am unable to see the pulse. I have tried slowing down the sweep on the scope and have adjusted the voltage and time scales but have not seen any response. After examing my DAQ card, I noticed that none of the PFI/TRIG terminals on the card are wired; the output channel connects to terminals for DAC0OUT and Ground. I'm wondering if this pin needs to be wired in orde
    r to generate the pulse since PFI0/TRIG1 is the start trigger terminal. Any help would be appreciated. Thanks.
    Attachments:
    ttl.vi ‏26 KB

    Hi,
    You are looking for a retriggerable pulse generation. Please check the Generate Retriggerable Pulse (DAQ-STC).vi example that ships with LabVIEW.
    Regards,
    RamziH.

  • I need to interface SCC-TC02 with help of SC 2345 and PCI-6024E DAQ Card.please tell me the procedure and if possible send me the program

    Dear Friends,
               I need to interface SCC-TC02 with help of SC 2345 and PCI-6024E DAQ Card.But i can not understand example program.please send me the procedure to interface these three componnets and if possible send me the program.
    With Regards,
    Eswaramoorthy K V

    nce of nth triggering pulse. i need to know when the when the ist trigger occurs and when the nth trigger occurs . please tell me how to to . what i know is that event triggering has to be done with start and stop trigger. please tell me how it has to doneSuresh;
    What you will need to do is to set up a digital start and stop triggered Analog Input acquisition. Then you will need to have a counter set as event counter, having the specific number of pulses you need configured as the preset value, configured to count down, and generating a pulse after the terminal count has been reached. That counter output will be the stop trigger of the Analog Input operation. In summary, you will have the external pulse being both the digital trigger of the Analog Input operation and the source pin of the counter, and the counter output being the digital stop signal for the analog input.
    I'm attaching a Labview VI that does the start and stop analog input acquisition. You will need to include the counter part and set the stop s
    ignal to be the counter output.
    Hope this helps.
    Filipe
    Attachments:
    AI_Start-Stop_D-Trig.zip ‏25 KB

  • Can version 7.1 work with a PCI-6024E?

    Hi! I've been trying to run a VI which is being successfully used in my lab to acquire data. However, whenever i try to run it i get stuck when the AI Waveform Scan VI file is being searched. Following your replies to similar questions i've made sure that the traditional NIDAQ is properly installed. is it possible that my data acquisition card (PCI-6024E) cannot support ver. 7.1? what do i do next?
    Thanks,
    Tamar

    from what i understand from your post, your problem has nothing to do with the card.
    your vi cannot run because a subvi is missing: AI Waveform Scan. it is probably in a different library than on the original computer (i would guess the original computer has a different version of LV installed). maybe it is one of the examples in a previous LV version?
    Either way, the easiest solution for you is to go to the original computer, save your vi with all dependencies (as an llb for example), and try again on the new computer.
    ... And here's where I keep assorted lengths of wires...

  • R6850 kit to connect 5B backplane to PCI-6024E DAQ card is it possible?

    I have an old 5B01 backplane that I have connected to an SC-2050. Can I connect the SC-2050 to my PCI-6024E DAQ car using the R6850 kit?

    Lcacho,
    I've reviewed the manuals and specifications for all those devices, and the connection should work.  Please note, however, that given the age of the 5B01 backplane, I cannot confirm this completely.  However, from the information I have, you should be able to connect all these devices.
    Seth B.
    Staff Test Engineer | National Instruments
    Certified LabVIEW Developer
    Certified TestStand Developer
    “Engineers like to solve problems. If there are no problems handily available, they will create their own problems.”- Scott Adams

  • Maximum Frequency on PCI-6024E

    Hello, I'm just wondering what is the maximum frequency can PCI-6024E hold?
    My sensor's range is .016KHz - 16.6665 KHz, if this is too much, can I just use
    a divider to cover what is max limit of the card?
    Thanks!
    KowdTek
    LabVIEW 2009
    One Step At A Time, Maybe Two...

    200Ksamples/sec on a single channel, per the specs:
    http://www.ni.com/pdf/manuals/370719c.pdf
    For optimum accuracy, sample at 5-10 times the highest frequency component of the signal if possible (minimum of 2x per Nyquist), that would be 166.6Ks/sec rate max which is still within range of the card.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~
    "It’s the questions that drive us.”
    ~~~~~~~~~~~~~~~~~~~~~~~~~~

  • Mdm:I want you to teach about installation of .mobileconfig.

    How do you do?
    It is Matsuzaki SHinji.
    I want you to teach about installation of .mobileconfig.
    iPhone composition   The utility is used.
    Server URL
    https://www.anetm.com/dav/pro
    CheckIn URL
    https://www.anetm.com/dav/chkin
    Topic
    com.apple.mgmt.jp.co.nishitele
    Peculiar name
    nj_dev_apns-dev-cert.p12
    The MDM server is using Apache 2.2.3.
    WavDAV is used.
    The PUT method is supported.
    The contract of an enterprise is completed.
    The application of MDM is also completed.
    I am using the following URL by webdav.
    It has also checked that it was in the state which can be used.
    https://www.anetm.com/dav/
    However, installation of a MDM composition profile cannot be performed.
    I want you to help.
    Apr 30 10:56:55 Evangerion-iPhone4S profiled [12362] <Notice>:   (Error) MC:   Profile"jp.co.nishitele.mdm.profile"failed. to install with error: NSError:
    Desc     : installation of the profile went wrong.
    Sugg     : a profile "jp.co.nishitele.safe.download.service" was not able to be installed.
    US Desc: Profile Failed to Install
    US Sugg:   The profile"jp.co.nishitele.safe.download.service"could not be installed.
    Domain : MCInstallationErrorDomain
    Code   : 4001
    Type   : MCFatalError
    ...Underlying error:
    NSError:
    Desc     : a profile "jp.co.nishitele.safe.download.service" was not able to be installed.
    Sugg     : a payload "mobile device management" was not able to be installed.
    US Desc:   The profile"jp.co.nishitele.safe.download.service"could not be installed.
    US Sugg:   The payload "mobile device management" could not be installed.
    Domain : MCProfileErrorDomain
    Code   : 1009
    Type   : MCFatalError
    Params : (
    "jp.co.nishitele.safe.download.service"
    ...Underlying error:
    NSError:
    Desc     : a payload "mobile device management" was not able to be installed.
    Sugg    :   Since a transaction with the server in "https://www.anetm.com/dav/chkin" was in the situation of "204", it failed.
    US Desc:   The payload "mobile device management" could not be installed.
    US Sugg:   A transaction with the server at"https://www.anetm.com/dav/chkin"has failed with the status"204."
    Domain : MCInstallationErrorDomain
    Code   : 4001
    Type   : MCFatalError
    Params : (
    "\U30e2\U30d0\U30a4\U30eb\U30c7\U30d0\U30a4\U30b9\U7ba1\U7406"
    ...Underlying error:
    NSError:
    Desc    :   Since a transaction with the server in "https://www.anetm.com/dav/chkin" was in the situation of "204", it failed.
    US Desc:   A transaction with the server at"https://www.anetm.com/dav/chkin"has failed with the status"204."
    Domain : MCHTTPTransactionErrorDomain
    Code   : 23001
    Type   : MCFatalError
    Params : (
    "https://www.anetm.com/dav/chkin",
    204
    Apache Server 2.2.3 http.conf
    Linux Redhat
    DavLockDB /var/lib/dav/lockdb
    <IfModule mod_dav_fs.c>
    <Location /dav/>
       Dav On
       Options Indexes
       Order deny,allow
       Allow from all
    </Location>
    </IfModule>
    And thank you.
    Thank you for your consideration.
    He is waiting for the reply.

    Perhaps useful to note the main thrust of discussion has continued on {thread:id=2496863} ....
    (NB: thanks OP for NOT supplying a link to this and wasting my time! ... I am not impressed by picking up a thread with zero replies to see a related thread discussion going on elsewhere)
    It certainly appears to me the thread was off topic for the forum it was in, though my java/j2ee is really scant, so I can't say for sure. As such OP probably has no gripe against a thread lock.
    Perhaps the question involved really which technology to use to solve a particular problem ... any may have skipped accross boundaries. As far as I can tell there is no appropriate 'general questions' category; but I suspect the thread might not have been out of totally out of context under
    {forum:id=922} ... but some may argue this is more under j2ee than straight Java. So an alternative forum suggestion or move might have been a different way to go. That said .... forum moderators have limited spare time so if they choose to lock rather than move that would be okay by me.
    I guess moderators will discuss this if necessary (if it is not already) on: Too much mod ( This is a moderator only discussion .... so i have no clue what is said).

Maybe you are looking for