Access Point POP authentication

Here everyone,
I would like to know if is possible to authenticate Access Point users by using their GMAIL accounts?.
I guess Google could provide some kind of Radius authentication using POP3 service or maybe, some third party Radius server could support POP3 authentication through Gmail accounts.
Thanks a lot in advance

I don't think that is possible.. you would have to know the users google account. Anyway's... wireless is separate and if the students are on the domain, just use PEAP or machine authentication and allow the Chrome books to logon to the network first.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

IOS 6.0.1 - Problems with certificate based authentication on wireless access point

Hi all
We are using iPad 2 as order terminals in our shops for about 5 months. Some of the iPads (the first who entered the field) started to cause problems now. These iPads are no longer able to keep long-term connection to the wireless access point in our stores. After selecting the SSID a successful authentication using the stored EAP-TLS certificate is performed (this can be seen in the log files of our wireless controller and by the IP adress that is given by DHCP). But within seconds the affected iPads opening up a captive portal page (empty, without contents) and separates the connection to the SSID after a short time again.
Affected are currently only iPads 2 with iOS 6.0.1, which were staged about 5 months ago. The newer devices with iOS 6.1+ connect without problems and open no captive portal page. The first cases occurred on the last Wednesday. Before that everything worked without difficulty. No modifications took place on the security structure. The numbers of affected devices increased until all iOS 6.0.1 were affected.
Access to other SSIDs (without use of certificates, by entering a key) for the devices is still possible (the devices does not open an captive portal page). The DHCP scope is not used up, so there are enough IP addresses available.
"Newer iPads" with an iOS of 6.1+ are are showing no problems on the same wireless access point, where the older devices are rejected. New and old devices use the same certificates and authentication mechanisms.
In the analysis of the issue, it turned out that the problem can be solved by an update to iOS 6.1.3. Subsequently, the iPads will be able to rebuild a connection with the access point, without a captive portal page.
Since the bandwidth is very narrow dimensioned in our stores, the communication of the iPads was severely restricted. Thus, the iPads are for exampleare accessible for the APNS but can not find iOS updates or check for their availability.
A comprehensive update to iOS 6.1.3 is currently excluded.
Does anyone knows this issue? What else can be done (except from updating)?

I will answer my own question in case it helps anyone else.
It would "seem" the ios 6 devices try the proxy and if that is not working they resort to the def gateway.
To Fix I did the following:
Brocade WIFI network has IPS and Advanced Firewall rules that seemed to be tthwarting some traffic, the iphones would then try the default gateway and be blocked at the FW.
I disabled the IPS and the Advanced Firewall Settings on the wifi as they are redundant to our main IPS and firewall that all traffic flows through anyway. I will tune it later, but when the CEO is demanding a fix "**** the security, full speed ahead"
Created some rues on the firewall to allow...
- IMAP-SSL (port993) outbound
- SMTPS (port 465) to yahoo servers outbound
- tcp port 587 to yahoo servers outbound
- https to akamai servers
Most http and https goes through the proxy as it should, BUT...
It seems that the akamai traffic allways ignores the wifi proxy settings and just heads straight for the default gateway. I suspect there is a bug in the icloud app?
Hope this helps someone else.
-Bo

Wireless Client Authentication issues when roaming Access Points (Local)

I have a Cisco 5508 with Software version 7.4.121.0 and Field Recovery 7.6.101.1.
There are a handful of clients that when roaming between AP's with the same SSID that get an authentication issue and have to restart the wireless to get back on.
From Cisco ISE
Event
5400 Authentication failed
Failure Reason
11514 Unexpectedly received empty TLS message; treating as a rejection by the client
Resolution
Ensure that the client's supplicant does not have any known compatibility issues and that it is properly configured. Also ensure that the ISE server certificate is trusted by the client, by configuring the supplicant with the CA certificate that signed the ISE server certificate. It is strongly recommended to not disable the server certificate validation on the client!
Root cause
While trying to negotiate a TLS handshake with the client, ISE expected to receive a non-empty TLS message or TLS alert message, but instead received an empty TLS message. This could be due to an inconformity in the implementation of the protocol between ISE and the supplicant. For example, it is a known issue that the XP supplicant sends an empty TLS message instead of a non-empty TLS alert message. It might also involve the supplicant not trusting the ISE server certificate for some reason. ISE treated the unexpected message as a sign that the client rejected the tunnel establishment.
I am having a hard time figuring out what is causing this. My assumption is if there were a problem with the Controller or AP configurations then it would happen to everyone. My further assumption is if the client had a problem with their laptop (windows 7) then why does work at other times? So I have checked and the ISE certificate is trusted by client.
Is something happening that the previous access point is holding on to the mac and the return authentication traffic is going to the old AP instead of the new one or something like that which is corrupting the data?
I also had this from Splunk for the same client:
Mar 5 13:44:51 usstlz-piseps01 CISE_Failed_Attempts 0014809622 1 0 2015-03-05 13:44:51.952 +00:00 0865003824 5435 NOTICE RADIUS: NAS conducted several failed authentications of the same scenario
FailureReason="12929 NAS sends RADIUS accounting update messages too frequently"
Any help on this would be appreciated. These error messages give me an idea but doesn't give me the exact answer to why the problem occurred and what needs to be done to fix it.
Thanks

Further detail From ISE for the failure:
11001
Received RADIUS Access-Request
11017
RADIUS created a new session
15049
Evaluating Policy Group
15008
Evaluating Service Selection Policy
15048
Queried PIP
15048
Queried PIP
15004
Matched rule
15048
Queried PIP
15048
Queried PIP
15004
Matched rule
11507
Extracted EAP-Response/Identity
12500
Prepared EAP-Request proposing EAP-TLS with challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12301
Extracted EAP-Response/NAK requesting to use PEAP instead
12300
Prepared EAP-Request proposing PEAP with challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12302
Extracted EAP-Response containing PEAP challenge-response and accepting PEAP as negotiated
12318
Successfully negotiated PEAP version 0
12800
Extracted first TLS record; TLS handshake started
12805
Extracted TLS ClientHello message
12806
Prepared TLS ServerHello message
12807
Prepared TLS Certificate message
12810
Prepared TLS ServerDone message
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
11514
Unexpectedly received empty TLS message; treating as a rejection by the client
12512
Treat the unexpected TLS acknowledge message as a rejection from the client
11504
Prepared EAP-Failure
11003
Returned RADIUS Access-Reject

IOS 4.2.1 breaks web-based authentication to wifi access points

Whenever I tried to access the *wifi access points* I use more often *whose authentication is web-based*, like the one at my public library or at my office, although I input my username and password correctly, I am always bounced back to the login form.
Before iOS 4.2.1 I know that there was a problem of this sort already, related to *some incompatibility between Safari's auto-fill features and the access points*, that could be solved by simply turning off auto-fill, and I did that. But know *it looks like the problem got to a new level of subtlety*.
Interestingly, *everything worked nicely while I was using the Gold Master version of iOS 4.2.0* that never made it to release, so the solution has to be found among the differences between 4.2.0 and 4.2.1, if you're an Apple engineer reading this.
Can you help? Any idea or trick to try that I didn't already? Thanks!
Giacecco

Hi Richard,
You mentioned that 'Apple put the AirPrint spec out there for all printer makers'. I've been looking around but I haven't found any spec. Where did you find it?
Do printer makers have to buy a license in order to be able to advertise that they've implemented the AirPrint protocol? Is there maybe an Apple review process in place?
TIA
Geert

Domain user authentication for 3650 Wireless Access point

Dear All,
I have got new proposal inorder to configure the wireless access points by managing with the 3650 wireless controller.
We wanted to block the Wifi Access to mobile users.
Only domain users need to be authenticate to the corporate wireless access.
We have 3650 switch as a wireless controller and ISE in place. Kindly guide me the achieve the same. Attached the setup diagram.
If possible share the sample configuration and it would be helpful.

Please refer
http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/115734-ise-policies-ssid-00.html

Unable to stop the event logs on access point console

Hi team,
I have an AIR-LAP1131AG-E-K9 access point having ios c1130-k9w8-mx.124-21a.JHB1.
When I am trying to take the console of it there are many logs generated like LWAPP ...Go join the controller, Discover controller etc. and the ap is unable to register to the controller(2112 with ios version 6.0.199.4). I'm trying to enter the command but there are many event msg generated....How do i stop this event log. I tried entering the command no debug all. but still there are many logs...
I want to enter the the following commands
#lwapp ap ip address <ip addr>.
#lwapp a pip default-gateway <gateway ip addr>
#lwapp ap controller ip addr <controller ip>
#wr me
Revert me back on urgent basis
Thanks in advance..

Thanks Rashika,
Now the access point got registered to the controller..This happened becuse of country Code..
I have changed the country code to UK, Belgium it started working fine.
Initially when it was IN the access point was not getting register..
But now the problem which arised is that the user is unable to get authenticated to the radius server.
Radius server is reachable and we have done every changes required for radius server authentication.
Users are getting rejected.
Customer is saying that the radius server is in IN domain and the WLC/access point is in UK,BE and hence the users are unable to connect..
Is it so??
Rply
Thanks in advance...

How do I make my AirPort Extreme a access point?

I just bought a Time Capsule and now I want to extend my range of my network. How do I make my AE an access point?

In this case, you will want to configure both base stations in an extended network.
Dynamic WDS - Extending a Wireless Network Setup
If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
Open AirPort Utility, and then, select the base station that will connect to the Internet.
Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
Click AirPort in the toolbar, and then, click Wireless.
Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
Next, select the base station that will extend this network, and then, choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
Enter the base station network and base station password if necessary.
Click Update to update the base station with new network settings.
(ref: Pages 43-44 of Apple AirPort Networks.)

An Error Occurred while trying to join "my wireless access point"

Hi,
I've been using wireless access for a year and never had a problem connecting.
But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
I get the strange feeling that they planted some kind of bug/virus!!!
I don’t know what else to do.
Anyone knows that problem? What can I do?
Any help is greatly appreciated!
I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

Hello Tesserax,
I get the same error message again...
I tried the 3 suggested steps again, but unfortunately it did not work.
After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
Even if the Computer was asleep for just a second!
I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
And it works fine…until the screensaver comes on or it sleeps again
I have the Problem with my IMac and Mini but the IMac at least remembers my password…
Any Ideas
I’m connected through a Buffalo WZR2-G300N wireless router

Access Points IP assignments

We have 1200 Series Wireless Access Points and the authentication is being done with BlueSSO RADIUS Authentication.
since last few months, we are facing that the machines / laptops are not provided with the IP address intended, instead they show 169.x.x.x ip address which is a default ip address of machines (when left unconfigured).
In the error logs we can only see the authentication not successfully. This is not an authentication issue as the very next moment if user tries again he will get connected.
Please suggest / advise if anything to be done OR the direction in which the troubleshooting should be done.
thx
raju +91 9867791104
india

Band select if enabled globally AND on ssid will push ur clients A band. Ok let us knw if problem is definitely gone.
Plz dnt forget to mark thread ad resolved if u say so.
Thank you,
Serge
sent from mobile

Access Point(s) - AIR-AP1231G-A-K9 and others - Spotty Connectivity ...

Hello,
We have eighteen Cisco Aironet wireless access points (most of them are AIR-AP1231G-A-K9 with 12.3(2)JA2 IOS loaded) across our campus which people have weird issues with connecting.
Everywhere, people can associate and get an IP address without any issues. However, they cannot maintain a reliable connection to systems either on our network or off. They will get a web page to load and then it drops them out. In addition, they cannot connect back again for random intervals of time. To make this even more bizarre is that for random intervals they maintain a solid connection until it kicks people out again.
The vlan itself (60 in the configuration file below) works without issue as we have devices plugged in directly to the vlan via a hardwired port and they are stable.
Below is the configuration file. Any reason why we would have this issue?
Thank you for your time.
Regards,
Christopher Koeber
!version 12.3no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname AP-6!enable secret {authentication information}enable password {authentication information}!username Cisco password {authentication information}username admin password {authentication information}ip subnet-zeroip domain name {Domain Information}!no aaa new-model!dot11 ssid (Secure) Staff/Faculty vlan 70 authentication open !dot11 ssid Public vlan 60 authentication open guest-mode!!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! ssid (Secure) Staff/Faculty ! ssid Public ! short-slot-time speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable!interface Dot11Radio0.60 encapsulation dot1Q 60 native no ip route-cache no cdp enable bridge-group 60 bridge-group 60 subscriber-loop-control bridge-group 60 block-unknown-source no bridge-group 60 source-learning no bridge-group 60 unicast-flooding bridge-group 60 spanning-disabled!interface Dot11Radio0.70 encapsulation dot1Q 70 no ip route-cache no cdp enable bridge-group 70 bridge-group 70 subscriber-loop-control bridge-group 70 block-unknown-source no bridge-group 70 source-learning no bridge-group 70 unicast-flooding bridge-group 70 spanning-disabled!interface FastEthernet0 no ip address no ip route-cache duplex auto speed auto!interface FastEthernet0.60 encapsulation dot1Q 60 native ip address 10.60.255.6 255.255.0.0 no ip route-cache bridge-group 60 no bridge-group 60 source-learning no bridge-group 60 unicast-flooding bridge-group 60 spanning-disabled!interface FastEthernet0.70 encapsulation dot1Q 70 ip address dhcp no ip route-cache bridge-group 70 no bridge-group 70 source-learning no bridge-group 70 unicast-flooding bridge-group 70 spanning-disabled!interface BVI1 ip address 10.60.255.6 255.255.0.0 no ip route-cache!ip default-gateway 10.60.0.1ip http serverno ip http secure-serverip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eagip radius source-interface BVI1 logging snmp-trap emergencieslogging snmp-trap alertslogging snmp-trap criticallogging snmp-trap errorslogging snmp-trap warnings!!!line con 0 transport preferred all transport output allline vty 0 4 login local transport preferred all transport input all transport output allline vty 5 15 login transport preferred all transport input all transport output all!end

Hi Christopher,
Couple of suggestions before moving forward:
1. I would first secure these WLANs with a least a pre-shared key if possible(WPA/WPA2). Let me know if you need information on how to do this.
2. Next, I would remove the 'short-slot-time' on the radio:
config terminal
interface do0
no short-slot-time
end
If your users continue to have issues, I would want more information on the types of clients in the environment as well as wireless adapter make/model/driver version.

Access Point - AIR-AP1231G-A-K9 - PCs can connect but Apple Macs Cannot ...

Hello,
This is a sort of follow up to a post I made a few days ago. I made changes to my access points and on Windows computers everything works but on Apple products (Macs, iPads, iPhones) the strangest things happen.
(1). About 90% of the time nothing works in that we get NO connection to the Access Point. In the client association logs we see the Mac Address show up but there is a 0.0.0 address where it seems like the device is trying to get an DHCP lease. After a while, the device gets the IPPA address of 169.X.X.X.
(2) After a extended period of time (an hour or more) the Apple device eventually gets an IP address from the network and then is able to successfully connect to the network. However, the connection is short lived and drops after about 30 minutes to an hour.
Is there a problem with the way Apple products encapsulates their network traffic versus Windows or other products?
Again, this not affect any Windows or Andriod based devices (laptops, phones, etc.) They can connect right away and never drop out.
Below is the configuration file for the AP in question, although this is affecting all of our APs:
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-5
enable {Authentication Information}
enable {Authentication Information}
username {Authentication Information}
username {Authentication Information}
ip subnet-zero
ip domain name {Domain here}
no aaa new-model
dot11 ssid (Secure) Staff/Faculty
   vlan 70
   authentication open
dot11 ssid Public
   vlan 60
   authentication open
   guest-mode
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid (Secure) Staff/Faculty
ssid Public
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
no cdp enable
interface Dot11Radio0.60
encapsulation dot1Q 60 native
no ip route-cache
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
no cdp enable
bridge-group 70
bridge-group 70 subscriber-loop-control
no bridge-group 70 source-learning
bridge-group 70 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.60
encapsulation dot1Q 60 native
ip address 10.60.255.5 255.255.0.0
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.70
encapsulation dot1Q 70
ip address dhcp
no ip route-cache
bridge-group 70
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface BVI1
ip address 10.60.255.5 255.255.0.0
no ip route-cache
ip default-gateway 10.60.0.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
logging snmp-trap emergencies
logging snmp-trap alerts
logging snmp-trap critical
logging snmp-trap errors
logging snmp-trap warnings
bridge 1 route ip
line con 0
transport preferred all
transport output all
line vty 0 4
login local
transport preferred all
transport input all
transport output all
line vty 5 15
login
transport preferred all
transport input all
transport output all
end

For initial configuration you can access AP from the Console port.
Following are the guides you need to look at for configuring you 1600 AP :
Cisco Aironet 1600/2600/3600 Series Access Point Deployment Guide
Getting Started Guide: Cisco Aironet 1600 Series Access Points
Moreover you can check the configuration guide from cisco.com/google, based on the Actual software image your AP is running. Some of the newer IOS for AP you can check here.
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Wrt54g as a wireless access point

alright i recently changed around my configuration with my wrt54g wireless router. I have made it into an access point which i was unaware is better. Im kinda new to the networking deal though it is what i want to do as a career and access points are new to me. so to the point of this post... when i make it an access point instead of the router i cannot access the admin setup page anymore. I know that when its the DHCP server you type in the default gateway that your given and the admin page pops up... well when its just an access point the gateway is from your router box not the linksys. so how if at all possible am i able to access the setup for the linksys if say i wanted to change the SSID of my network? i appreciate any help
Solved!
Go to Solution.

It depends. If you have another gateway router then you should assign a LAN IP address inside the gateway router LAN. For instance, if your gateway router uses 192.168.0.1/255.255.255.0 then you could assign a LAN IP address of 192.168.0.2/255.255.255.0, turn off the DHCP server and do the LAN-LAN connection.
If you only have a simple modem and the computers make a direct connection to your ISP then you have to set up a static IP address temporarily. Assuming you did not change the LAN IP address of the WRT from 192.168.1.1/255.255.255.0 you would assign a static IP address 192.168.1.2 with subnet mask 255.255.255.0 on the computer. With this static IP address the computer can access http://192.168.1.1/ After that you change the computer back to DHCP (Retrieve IP address automatically).

6600 access point - pain / help me

I've just got me hands on a 6600 and it keeps asking me to select an access point (ie: GPRS or my provider) if I say yes it dials up the number - if I say no (cancel) it go's away for about a minute then "pops" back up - can anbody tell me how to STOP it poping back up!!! its driving me round the bend
ps - I have looked in the providers manual (not a Nokia manual) and its no help.
Thanks

Does this help: http://discussions.nokia.co.uk/discussions/board/message?board.id=messaging&message.id=89&query.id=0...

N97 OTA access point help

hi all, got a probem here that seems to been doin my head in over the last few days. basically i bought a brand new locked to tmobile N97, im a virgin customer.. now, i'm wanting to do a firmware upgrade.. due to having an old **bleep** laptop that only has 248mb of ram i cant d the upgrade via nokia pc suite so my only other option is OTA.. right, so, i dial *#0000# then go to options, then check for updates... up pops a message saying a need to define an access point, ok.. not understanding it much i try and manually add some stuff myself, to no avail... then i do some forum posting and manage to get these settings: Server Name Nokia Server ID Nokia Server password firmupservpass Access point [select your preferred AP] Host address https://dms.update.nokia.com/dms/omadm Port 443 User name nokiams DM password nokiamspass Allow configuration Yes Auto accept all requests Yes but... that hasnt solved my problem, when entered and i try to connect to do the upgrade i get a connection error. my only option is this forum, its a nokia fone and a nokia forum i cant get my head round it as i can use the internet n my fone brilliantly, surely the internet and the OTA access point are the same thing?

To add an access point select settings-connectivity-destinations-Access point , Automatically search for available access points ?, select yes and choose access point. Then go into Internet and set the priorities to WLAN number 1 T-Mobile number 2 etc
Good Luck
PS Nokia Software Updater should still work on computer, even with low memory or weak internet , just a bit slower.
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Strange VLAN issue on aironet access points

I'm setting up some access points for WPA. I've ran into a strange issue. The client VLAN (VLAN that the users will be put into) is 1, and the native VLAN is 10. The RADIUS server is in VLAN 1 (but I have a test RADIUS server in VLAN 10 as well). I can connect from the access point to a RADIUS server in either VLAN, and from the RADIUS servers to the access point as well. When I point to a RADIUS server in VLAN10 authentication works fine. If I point to a RADIUS server that is located in VLAN1, and I put the wireless clients in VLAN10 it works fine. But for some reason when I have the RADIUS server and the clients in VLAN (1) and the native (BVI1) interface in VLAN 10 the authentication packets never seem to get to the RADIUS server. It is as if the authentication is being sources out of the wrong VLAN. I can?t find any docs to say that this isn?t a supported configuration.

Hi Shannon,
have a look here:
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#apconfig
- - - Snipp - - -
Significance of Native VLAN
When you use an IEEE 802.1Q trunk port, all frames are tagged except those on the VLAN configured as the "native VLAN" for the port. Frames on the native VLAN are always transmitted untagged and are normally received untagged. Therefore, when an AP is connected to the switchport, the native VLAN configured on the AP must match the native VLAN configured on the switchport.
Note: If there is a mismatch in the native VLANs, the frames are dropped.
This scenario is better explained with an example. If the native VLAN on the switchport is configured as VLAN 12 and on the AP, the native VLAN is configured as VLAN 1, then when the AP sends a frame on its native VLAN to the switch, the switch considers the frame as belonging to VLAN 12 since the frames from the native VLAN of the AP are untagged. This causes confusion in the network and results in connectivity problems. The same happens when the switchport forwards a frame from its native VLAN to the AP.
- - - Snapp - - -
Best regards,
Frank

Access Point POP authentication

Similar Messages

Maybe you are looking for