ACE 4710 responds very slow to CLI commands

I am expericing delayed responses to my CLI commands on the ACE 4710. The delays occur sporadically. I have check the cpu and memory and neither one appeared to show any abnormal behaviour. Has anybody else experienced unsual delay with your CLI commands? If so, where you able to isolate and correct the problem? If not, any suggestions on where and how to look for the problem?

I am experiencing the same exact problem. CLI commands are very slow. Although, i dont get any performance issues for my application when i issue the "show run" or "wr mem" commands at CLI i wait for over 1 minute to receive any output, commands like "show serverfarm" ,"show rserver" "show stats" are working fine. my resource usage is ok and cpu has no problems. The problem exists in all contexts of the specific ACE. I did a test by forcing the standby ace to become active and while the standby ACE had no problem in executing the command when it becomes the active one the problem shows up. is there a way to troubleshoot this?
Thank you in advance

Similar Messages

Access Server through VIP (ACE 4710) but very slow

Re: Access Server through VIP (ACE 4710) but very slow
Hi Shiva
Kindly Help .....Accessing the server very slow.., Plz check my real configuration... this configuration is for application server and after this i have to configure more serverfarm for different server like webmail etc. in this ACE 4710. I have only one ACE 4710 .
ACE Version A4(2.0) = is there supports Probe with this version.??? without probe server will work but very slow. And plz guide Nat-pool is required
VIP :-- 172.16.15.8
LB/Admin# sh run
Generating configuration....
no ft auto-sync startup-config
logging enable
logging host 172.29.91.112 udp/514
resource-class RC1
limit-resource all minimum 10.00 maximum unlimited
boot system image:c4710ace-mz.A4_2_0.bin
hostname LB
interface gigabitEthernet 1/1
description Management
speed 1000M
switchport access vlan 1000
no shutdown
interface gigabitEthernet 1/2
description clientside
switchport access vlan 30
no shutdown
interface gigabitEthernet 1/3
description serverside
switchport access vlan 31
no shutdown
interface gigabitEthernet 1/4
no shutdown
context Admin
description Management
member RC1
access-list everyone line 8 extended permit ip any any
access-list everyone line 16 extended permit icmp any any
probe http probe1
description health check
interval 5
passdetect interval 10
request method head
expect status 200 200
open 1
rserver redirect https_redirect
description redirect traffic to https
webhost-redirection / 302
inservice
rserver redirect maintenance_page
description maintenance page displayed
webhost-redirection /sry.html 301
inservice
rserver host web1
ip address 192.168.10.3
inservice
rserver host web2
ip address 192.168.10.4
inservice
rserver host web3
ip address 192.168.10.5
inservice
serverfarm host http
rserver web1
    inservice
rserver web2
    inservice
rserver web3
    inservice
serverfarm redirect https_redirect_farm
description Redirect traffic to https
serverfarm redirect maintenance_farm
description send user to maintenance page
parameter-map type connection paramap_http
description parameter connection tcp
exceed-mss allow
sticky ip-netmask 255.255.255.0 address source Sticky_http
timeout activeconns
serverfarm http
class-map match-all REMOTE-ACCESS
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
class-map match-all slb-vip
2 match virtual-address 172.16.15.8 tcp eq www
policy-map type management first-match remote_access
class class-default
    permit
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
    permit
policy-map type loadbalance first-match slb
class class-default
    serverfarm http
policy-map type inspect http all-match slb-vip-http
class class-default
    permit
policy-map multi-match client-vips
class slb-vip
    loadbalance vip inservice
    loadbalance policy slb
    loadbalance vip icmp-reply active
    inspect http policy slb-vip-http
    connection advanced-options paramap_http
interface vlan 30
description "Client Side"
ip address 172.16.15.24 255.255.255.0
access-group input everyone
service-policy input client-vips
no shutdown
interface vlan 31
description "Server Side"
ip address 192.168.10.1 255.255.255.0
service-policy input remote_access
no shutdown
interface vlan 1000
description managment
ip address 172.29.91.110 255.255.255.0
service-policy input remote_mgmt_allow_policy
no shutdown
ip route 0.0.0.0 0.0.0.0 172.16.15.1
snmp-server contact "PHQ"
snmp-server community phq group Network-Monitor
snmp-server trap-source vlan 1000
username admin password 5 $1$b2txbc5U$TA74D920oSdd2eOZ4hSFe/ role Admin domain
default-domain
username www password 5 $1$.GuWwQEK$r8Ub4OcE3l190d5GA4kvR. role Admin domain de
fault-domain
username prem password 5 $1$8C7eRKrI$it3UV4URZ26X4S/Bh6OEr0 role Admin domain d
efault-domain
ssh key rsa 1024 force
banner motd # "ro" #
Regards,
Prem

Hi Shiva,
plz guide i'm new with ACE LB, also find my n/w design for connected ace to server. but server accessing very very slow, but when i connect through my old server software LB (with two interface)then accessing very fast. I just replace my old serverLB(with two interface) to ACE4710 and connect the same scenario then why not server accessing smoothly with VIP .Reply soon only I connect ACE's two interface with switch.....
Regards,
Prem

CQ5 server is responding very slow?

Hello,
CQ5 server is responding very slow, when I start to create package through package manager and I am creating package for a DAM and its responding very slow.
There is only one user accessing server.
when I started to create package it may be opening lot of CRXSession, I checked using below command
jmap -histo:live <pid> | grep CRXSessionImpl
And it show me more than 110 CRXSession is opened.
Can any one tell me how we can optimize server, how we can close CRXSession automatically, even I run garbage collector still getting same issue.
Regards,
Satish

For starters answers to a few questions would help:
1. What kind of hardware config is in place? (RAM, disk-space)
2. Which OS are you running instances? Are both author and publish on same machine?
3. Have you checked error logs?
From the problem description you have provided 1st seems to be the main issue.
- Ashish

MDM Server is responding very slow

Hi,
I am working with only 21,695 records and MDM Server is responding very slow.
MDM Server is running on Intel(R)Xeon(TM) 2.40Ghz 2.39Ghz, 3.89 GB of RAM.
System: Microsoft Windows Server 2003 Standard Edition Service Pack 2.
The hard disk partition F: has 43.7 GB Freespace.
It is impossible to do MDM Workflow matching and Merging with this slow speed.
Regards
Kaushik Banerjee

Hi Kaushik,
Please try to stop and restart the database server.
You can check the below:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes/sdn_oss_mdm/~form/handler7b5f4150503d3030323030363832353030303030303031393732265f4556454e543d444953504c4159265f4e4e554d3d31303132373435%7d
Re: MDM Server is very slow and locks users out
Hope it helps.
Thank you,
Priti

Macbook pro 2010...cursor is acting crazy jumping everywhere and responding very slow...thought it was the track pad but I plugged in a mouse and it still does the same thing...is this a virus?..and can someone please help?...

My Macbook pro is acting Crazy....the Cursor just keeps on jumping everywhere and not responding when I use the trackpad....Even when it does respond it is very slow...I thought it was the trackpad acting up but realized it wasnt when i plugged in a mouse and it still did the same thing...this happened one other time and shortly after my computer froze...I had to restart for it to work but restarting dosent help this time...can someone please help?...Is this a Virus?

It is not a virus. See my Mac Virus Guide*.
As to what it might be, that's hard to say. You should try some basic troubleshooting... Repair the hard drive with disk utility. Boot in safe mode and see if it happens then, log in to a different user account and see if it happens there, reboot from another system and see if it happens.
Apparently some people have had this kind of problem caused by swelling batteries that push on the underside of the trackpad and cause all kinds of strange problems. Is your machine's underside deformed at all?
* Disclaimer: links to my pages may give me compensation, and should not be taken as endorsement of my services by Apple.

HT1338 my mac book is responding very slow..mostly I'm surfing 3-5 pages at a time.i can't understand what to do?please help me

im new to mac book...in the start few weeks mac book was very fine i love it...but as time passed its getting slower & slower.what should i do.it has updated software MAC OS X 10.7.4 but still very slow.

First, back up all data immediately, as your boot drive may be failing.
If iCloud is enabled, disable it.
Disconnect all wired peripherals except keyboard, mouse, and monitor, if applicable. Launch the usual set of applications you use when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Step 2
You must be logged in as an administrator to carry out this step.
Launch the Console application in the same way as above. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
Important: Some personal information, such as your name, may appear in the log. Edit it out before posting.

IPOD 80 gb is responding very slow

First time poster. I did a search and found nothing. My problem is my ipod classic responds very slowly these days. I'm guessing it's because I have about 70 gb of music on it, and it's just "full". But this is getting very annoying. The wheel is not as responsive and it takes several "brushes" with my fingers to make anything happen.
This is extremely frustrating when I have the earbuds in and I'm trying to raise the volume - I'll scroll the wheel, and scroll and scroll and nothing. After several scrolls it will FINALLY WORK AND GO TO MAXIMUM VOLUME AND BLAST MY EARDRUMS!.
Does anyone know potential causes and/or fixes?
Thank you,
Clem

I would try a restore. Despite having that much content it should still operate normally.

11g on Windows started all of a sudden to respond very slow on TNSPING

Here is the listener.ora and the tnsnames.ora
# listener.ora Network Configuration File: C:\app\administrator\product\11.2.0\dbhome_1\NETWORK\ADMIN\listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1522))
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = odb1.domain.com)(PORT = 1522))
(PROTOCOL_STACK =
(PRESENTATION = GIOP)
(SESSION = RAW)
ADR_BASE_LISTENER = C:\app\administrator
# tnsnames.ora Network Configuration File: C:\app\administrator\product\11.2.0\dbhome_1\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
LISTENER_ODB =
(ADDRESS = (PROTOCOL = TCP)(HOST = odb1.domain.com)(PORT = 1522))
ODB =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = odb1.domain.com)(PORT = 1522))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = odb1.domain.com)
Symptoms:
1. the solution use to work like a breeze, until 10 days ago when problems started when after a windows update i restarted the machine.
2. The first time I do a tnsping, I get a response in 20 ms. After that every time I do the same it takes 5000 ms or more
3. Client can't connect anymore over the network (verified the tnsnames to be correct)
4. I can connect only using Local Bequeath connection.
I have seen several cases on the internet but nothing seems to match my case (windows OS)
steps already done: I did add the full name on the hosts file to expedite the resolution
restarted the listener after each change
Any help will be highly appreciated.
Thanks

I did it and I copy here the result of the file tnsping.trc:
Any idea?
Thanks
TNS Ping Utility for 32-bit Windows: Version 11.2.0.1.0 - Production on 29-SEP-2011 16:06:58
Copyright (c) 1997, 2010, Oracle. All rights reserved.
--- TRACE CONFIGURATION INFORMATION FOLLOWS ---
New trace stream is c:\trace\tnsping.trc
New trace level is 4
--- TRACE CONFIGURATION INFORMATION ENDS ---
--- PARAMETER SOURCE INFORMATION FOLLOWS ---
Attempted load of system pfile source C:\app\administrator\product\11.2.0\dbhome_1\network\admin\sqlnet.ora
Parameter source loaded successfully
-> PARAMETER TABLE LOAD RESULTS FOLLOW <-
Successful parameter table load
-> PARAMETER TABLE HAS THE FOLLOWING CONTENTS <-
TNSPING.TRACE_LEVEL = 4
NAMES.DIRECTORY_PATH = (TNSNAMES, EZCONNECT)
TNSPING.TRACE_DIRECTORY = c:\trace
SQLNET.AUTHENTICATION_SERVICES = (NTS)
--- PARAMETER SOURCE INFORMATION ENDS ---
--- LOG CONFIGURATION INFORMATION FOLLOWS ---
Log stream will be "standard output"
Log stream validation not requested
--- LOG CONFIGURATION INFORMATION ENDS ---
nnftmlf_make_local_addrfile: construction of local names file failed
nnftmlf_make_system_addrfile: system names file is C:\app\administrator\product\11.2.0\dbhome_1\network\admin\tnsnames.ora
nscall: connecting...
nsc2addr: (DESCRIPTION=(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=odb))(ADDRESS=(PROTOCOL=TCP)(HOST=192.168.1.50)(PORT=1522)))
nttbnd2addr: using host IP address: 192.168.1.50
nsopen: opening transport...
nttcni: Tcp conn timeout = 60000 (ms)
nttcni: trying to connect to socket 1580.
nttcni: connected on ipaddr 192.168.1.50
nttcon: set TCP_NODELAY on 1580
nsopen: transport is open
nsopen: global context check-in (to slot 0) complete
nscon: doing connect handshake...
nscon: sending NSPTCN packet
nscon: got NSPTRF packet
nscall: refused
nstimarmed: no timer allocated
nsclose: closing transport
nsclose: global context check-out (from slot 0) complete

Phone App - Responds very slow or delay to touch/scroll

My IPhone4 ver4.1 -
There is a delay when I touch a key or try to scroll in the phone app it. Has anyone experience this? Any fis to this issue?

Hmmm... not good.
You are describing the classic "Battery Drain" problem and you will find a lot of post here about that issue.
On my current phone iP4 #2, I ran into a little problem while updating to iOS4.1 and ended up doing a "Setup/Configure as new".
I don't know if I had the problem on phone #2 or would have if I had not done the "Setup as new" but in any case my phone does not have the battery drain or heat problem.
Check some of the other post on this. The general gist of the problem is that during the iOS-4.1 update a piece of code (modem firmware) gets hung in a loop using a tremendous amount of CPU resources and of course BATTERY.
Some claim they have done the setup as new two or three time to clear this problem. And Oh by the way don't due a restore afterward and make sure you do a sync prior to doing the setup as new then after the setup as new just re-sync and all your apps and music... etc. should be restored to your phone.

After downloading 7 to my i-pad 2 the keyboard has become very slow responding and typing takes forever why?

After downloading the new 7.0.2 to my i-pad2 the onscreen keyboard is responding very slow. I have to wait for several seconds for it to show up on the screen after touching any key.

Reset all settings
Settings>General>Reset>Reset All Settings
Note: Data will not be affected but settings will be reset.

MacBook Pro (15-inch, Late 2008) suddenly very slow and laggy

This seems to be a popular question so I apologize, but I know there can be a number of issues that cause a computer to run slow, so I want to post my computer's specifics and hopefully someone can diagnose the issue for me without my having to bring it into the store. Thank you in advance.
Specifically my MacBook runs slow when trying to open or close Microsoft Word, iTunes, or access a folder with pictures and short videos in it. Frequently I get they are not responding, or have to close out of everything else in order to get the spinning wheel to go away and sometimes that doesn't even help.
I would just like the computer to be able perform simple commands in a timely manner like it used to. If there is any way I can get back to this I would be eterrrrnally grateful!
Problem description:
MacBook responds very slow when trying to open applications. Slow, lags, rainbow spinning wheel all the time, even just to open a folder with pictures.
EtreCheck version: 2.0.6 (91)
Report generated October 24, 2014 at 8:07:12 PM PDT
Hardware Information: ℹ️
MacBook Pro (15-inch, Late 2008) (Verified)
MacBook Pro - model: MacBookPro5,1
1 2.66 GHz Intel Core 2 Duo CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1067 MHz ok
BANK 0/DIMM1
2 GB DDR3 1067 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
NVIDIA GeForce 9600M GT - VRAM: 512 MB
Color LCD 1440 x 900
NVIDIA GeForce 9400M - VRAM: 256 MB
System Software: ℹ️
OS X 10.10 (14A389) - Uptime: 6 days 19:54:17
Disk Information: ℹ️
Hitachi HTS543232L9SA02 disk0 : (320.07 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
OS X (disk0s2) / [Startup]: 319.21 GB (122.35 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
HL-DT-ST DVDRW GS21N
USB Information: ℹ️
Apple Inc. iPhone
Apple Inc. Built-in iSight
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Apple, Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Configuration files: ℹ️
/etc/hosts - Count: 15
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Applications/Toast 10 Titanium/Toast Titanium.app
[not loaded] com.roxio.BluRaySupport (1.1.6) Support
[not loaded] com.roxio.TDIXController (1.7) Support
/System/Library/Extensions
[not loaded] com.ManyCamLLC.videodevice.driver (2.0.10 - SDK 10.7) Support
[not loaded] com.devguru.driver.SamsungComposite (1.2.61 - SDK 10.6) Support
[not loaded] com.leapfrog.codeless.kext (2) Support
[not loaded] com.leapfrog.driver.LfConnectDriver (1.9.8 - SDK 10.8) Support
[loaded] com.rim.driver.BlackBerryUSBDriverInt (0.0.68) Support
[not loaded] com.rim.driver.BlackBerryUSBDriverVSP (0.0.68) Support
/System/Library/Extensions/ManyCamVideoDeviceDriver.kext/Contents/PlugIns
[not loaded] com.ManyCamLLC.videodevice.userclient (2.0.10 - SDK 10.7) Support
/System/Library/Extensions/ssuddrv.kext/Contents/PlugIns
[not loaded] com.devguru.driver.SamsungACMControl (1.2.61 - SDK 10.6) Support
[not loaded] com.devguru.driver.SamsungACMData (1.2.61 - SDK 10.6) Support
[loaded] com.devguru.driver.SamsungMTP (1.2.61 - SDK 10.5) Support
[not loaded] com.devguru.driver.SamsungSerial (1.2.61 - SDK 10.6) Support
Problem System Launch Agents: ℹ️
[failed] com.apple.AirPlayUIAgent.plist
[failed] com.apple.CallHistoryPluginHelper.plist
[failed] com.apple.CallHistorySyncHelper.plist
[failed] com.apple.cmfsyncagent.plist
[failed] com.apple.EscrowSecurityAlert.plist
[failed] com.apple.gamed.plist
[failed] com.apple.printtool.agent.plist
[failed] com.apple.recentsd.plist
[failed] com.apple.sbd.plist
[failed] com.apple.scopedbookmarkagent.xpc.plist
[failed] com.apple.security.cloudkeychainproxy.plist
[failed] com.apple.telephonyutilities.callservicesd.plist
Problem System Launch Daemons: ℹ️
[failed] com.apple.AssetCacheLocatorService.plist
[failed] com.apple.awdd.plist
[failed] com.apple.ctkd.plist
[failed] com.apple.diagnosticd.plist
[failed] com.apple.icloud.findmydeviced.plist
[failed] com.apple.Kerberos.digest-service.plist
[failed] com.apple.nehelper.plist
[failed] com.apple.nsurlsessiond.plist
[failed] com.apple.periodic-daily.plist
[failed] com.apple.periodic-weekly.plist
[failed] com.apple.softwareupdate_download_service.plist
[failed] com.apple.systemstats.analysis.plist
[failed] com.apple.tccd.system.plist
[failed] com.apple.wdhelper.plist
[failed] com.apple.xpc.smd.plist
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
[failed] com.adobe.CS5ServiceManager.plist Support
[loaded] com.google.keystone.agent.plist Support
[loaded] com.oracle.java.Java-Updater.plist Support
[running] com.rim.BBAlbumArtCacher.plist Support
[running] com.rim.BBLaunchAgent.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[invalid?] com.adobe.SwitchBoard.plist Support
[loaded] com.ea.origin.ESHelper.plist Support
[loaded] com.google.keystone.daemon.plist Support
[loaded] com.leapfrog.connect.authdaemon.plist Support
[invalid?] com.ManyCamLLC.videodevice.daemon.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
[running] com.rim.BBDaemon.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist Support
[running] com.leapfrog.connect.monitor.plist Support
[running] com.spotify.webhelper.plist Support
[invalid?] com.valvesoftware.steamclean.plist Support
User Login Items: ℹ️
Flux Application (/Applications/Flux.app)
iTunesHelper UNKNOWNHidden (missing value)
NambuHelper UNKNOWN (missing value)
Orb UNKNOWN (missing value)
Google Notifier UNKNOWN (missing value)
Synergy UNKNOWN (missing value)
Dropbox UNKNOWN (missing value)
Flux UNKNOWN (missing value)
Calendar Application (/Applications/Calendar.app)
Google Chrome ApplicationHidden (/Applications/Google Chrome.app)
Cinch UNKNOWN (missing value)
fuspredownloader ApplicationHidden (/Users/[redacted]/Library/Application Support/.FUS/fuspredownloader.app)
Spotify ApplicationHidden (/Applications/Spotify.app)
BlackBerry Device Manager ApplicationHidden (/Library/Application Support/BlackBerry/BlackBerry Device Manager.app)
Internet Plug-ins: ℹ️
JavaAppletPlugin: Version: Java 7 Update 55 Check version
o1dbrowserplugin: Version: 5.4.2.18903 Support
Default Browser: Version: 600 - SDK 10.10
Flip4Mac WMV Plugin: Version: 2.3.6.5 Support
AdobePDFViewerNPAPI: Version: 10.1.12 Support
FlashPlayer-10.6: Version: 15.0.0.189 - SDK 10.6 Support
Silverlight: Version: 5.1.20913.0 - SDK 10.6 Support
Flash Player: Version: 15.0.0.189 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
googletalkbrowserplugin: Version: 5.4.2.18903 Support
SharePointBrowserPlugin: Version: 14.4.1 - SDK 10.6 Support
AdobePDFViewer: Version: 10.1.12 Support
DirectorShockwave: Version: 11.6.6r636 Support
User Internet Plug-ins: ℹ️
WebEx64: Version: 1.0 - SDK 10.6 Support
WebEx: Version: 1.0 Support
Dashlane: Version: Dashlane 1.0.0 - SDK 10.7 Support
ZoomUsPlugIn: Version: ZoomBundleVersionNumber - SDK 10.9 Support
Safari Extensions: ℹ️
Dashlane
3rd Party Preference Panes: ℹ️
Connect360 Support
Flash Player Support
Flip4Mac WMV Support
Growl Support
Java Support
MediaLink Support
Perian Support
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
      26% Finder
      16% QuickLookUIHelper
      13% WindowServer
      2% quicklookd
      1% hidd
Top Processes by Memory: ℹ️
218 MB Finder
206 MB iTunes
120 MB Google Chrome
82 MB Skype
82 MB Google Chrome Helper
Virtual Memory Information: ℹ️
253 MB Free RAM
1.65 GB Active RAM
670 MB Inactive RAM
714 MB Wired RAM
39.22 GB Page-ins
1.92 GB Page-outs

Resetting SMC could solve the problem.
Intel-based Macs: Resetting the System Management Controller (SMC)
And you need to install more RAM, I think.

CQ5 server performance is very slow ?

Hello,
I deployed my project on publish server, but both the server responding very slow, Is it the CQ5 server the very slow?
Please let me know how to make more faster performance of CQ5 server, please let me know is there any configration we have to do?
For showing the page around it takes 10min, how to solve such issues.
Please let me know any perfoamance tuning guide/tricks.
Regards,
Satish

For starters answers to a few questions would help:
1. What kind of hardware config is in place? (RAM, disk-space)
2. Which OS are you running instances? Are both author and publish on same machine?
3. Have you checked error logs?
From the problem description you have provided 1st seems to be the main issue.
- Ashish

OSB sbconsole responding too slow

HI,
when i deploy project or click any link in the osb's sbconsole,it responds very slow.And i want to know how to solve the problem.
Anyone can help me or give some advice.
thanks.
Some information of my domain is:
root 3998012 2556410 0 Apr 28 - 117:05 /usr/java6_64/bin/java -Xdebug -Xnoagent -Xrunjdwp:transport=dt_socket,address=8453,server=y,suspend=n -Djava.compiler=NONE -Xms2048m -Xmx2048m -Dweblogic.Name=AdminServer -Djava.security.policy=/usr/local/Oracle/Middleware/wlserver_10.3/server/lib/weblogic.policy -da:org.apache.xmlbeans... -ea -da:com.bea... -da:javelin... -da:weblogic... -ea:com.bea.wli... -ea:com.bea.broker... -ea:com.bea.sbconsole... -Dplatform.home=/usr/local/Oracle/Middleware/wlserver_10.3 -Dwls.home=/usr/local/Oracle/Middleware/wlserver_10.3/server -Dweblogic.home=/usr/local/Oracle/Middleware/wlserver_10.3/server -Ddomain.home=/usr/local/Oracle/Middleware/user_projects/domains/base_domain -Dcommon.components.home=/usr/local/Oracle/Middleware/oracle_common -Djrf.version=11.1.1 -Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger -Djrockit.optfile=/usr/local/Oracle/Middleware/oracle_common/modules/oracle.jrf_11.1.1/jrocket_optfile.txt -Doracle.domain.config.dir=/usr/local/Oracle/Middleware/user_projects/domains/base_domain/config/fmwconfig -Doracle.server.config.dir=/usr/local/Oracle/Middleware/user_projects/domains/base_domain/config/fmwconfig/servers/AdminServer -Doracle.security.jps.config=/usr/local/Oracle/Middleware/user_projects/domains/base_domain/config/fmwconfig/jps-config.xml -Djava.protocol.handler.pkgs=oracle.mds.net.protocol -Digf.arisidbeans.carmlloc=/usr/local/Oracle/Middleware/user_projects/domains/base_domain/config/fmwconfig/carml -Digf.arisidstack.home=/usr/local/Oracle/Middleware/user_projects/domains/base_domain/config/fmwconfig/arisidprovider -Dweblogic.alternateTypesDirectory=/usr/local/Oracle/Middleware/oracle_common/modules/oracle.ossoiap_11.1.1,/usr/local/Oracle/Middleware/oracle_common/modules/oracle.oamprovider_11.1.1 -Dweblogic.jdbc.remoteEnabled=false -Dweblogic.management.discover=true -Dwlw.iterativeDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=/usr/local/Oracle/Middleware/patch_wls1033/profiles/default/sysext_manifest_classpath:/usr/local/Oracle/Middleware/patch_ocp353/profiles/default/sysext_manifest_classpath weblogic.Server
java version "1.6.0"
Java(TM) SE Runtime Environment (build pap6460sr9fp1-20110208_03(SR9 FP1))
IBM J9 VM (build 2.4, JRE 1.6.0 IBM J9 2.4 AIX ppc64-64 jvmap6460sr9-20110203_74623 (JIT enabled, AOT enabled)
J9VM - 20110203_074623
JIT - r9_20101028_17488ifx3
GC - 20101027_AA)
JCL - 20110203_01

Please refer below threads -
OSB sbconsole responding slow.
OSB 10gR3: sbconsole very slow after 10-15 OSB projects
Regards,
Anuj

SharePoint Site Very Slow and some time Request Timed Out

Hi All
I have many Web Application is running in SharePoint Farm. Since yesterday one of the web application started responding very slow. It takes 5 to 6 mins to load the page. Some time i received request timed out error message. But all other web applications
are working good.
I increased executionTimeout value, stall it slow / not responding.
Please let us know if you have come across this issues or any suggestion from your end to resolve this issue.
Thanks in Advance - Guru
Cheers, Guruprasad

i would recommend enable the developer dashboard on the web app and check which task is consuming the more time i.e. webpart, query to database etc.
also any change to web app since the issue started, any new webpart added to the page, any solution deployed or something else.
also did you try to recycle the app pool of the web applications?
how many wfe in the farm?
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

WIFI too slow after IOS 6 installed. SAFARI is loading very slow for burmese language website. Please help.....

WIFI too slow after IOS 6 installed. SAFARI is loading very slow for burmese language websites. Not only that....many other websites too.....Please help.....Don't expect that ENglish is only language we expect to view on IPAD......
Most websites are responding very slow with safari & many other broswers opera.........Too annoying IOS 6...Give me IOS 5 back...Tell me how.....
I am too angry with IOS 6.......My IPAD 2 & IPHONE 4S all suck after installing IOS 6..........
I can't believe "$600 billions " company released without testing on every devices with different wifi routers, applications on their store.........
Give me some ways to downgrade to IOS 5.1.1......

iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
You may think you are connected to the internet, but maybe not. Click on Safari and see if it connects.
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting
http://www.apple.com/support/ipad/wifi/
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

ACE 4710 responds very slow to CLI commands

Similar Messages

Maybe you are looking for