Acer aspire 5560g Failing to boot after Firmware update

Hey guys, So i recently upgraded my Aspire 5560g to Windows 8.1. I liked it but it seemed to have lost my drivers in the process (my track pad scrolling didnt work and my Dolby audio origram was gone). I went to for the drivers and decided to start with a firmware upgrade (9545 for hard disk performance). After the computer rebooted, I entered the dreaded Windows 8.1 boot loop. It would say "Your PC ran into problems..." with the bluescreen, then turn off. Then it would attempt the Automatic repair, and fail again, then restart the cycle. I wasn't able to even get into my BIOS until I cleared my CMOS, now at least I can get into BIOS. I created a bootable USB for Windows in hopes I could do a clean install, but even when trying to boot from a USB I get the blue Windows 8 screen, "Your PC ran into problems..."
Is there a way I can undo the firmware update, it seems like the culprit, doesn't it? Any help appreciated. Thanks EDIT: I've read that the Windows boot loop may be caused by outdated drivers. Think this could be the problem after I did the firmware update? How can I install the drivers without being able to boot into Windows? Thanks

Okay, I tried each stick at a time in both slots with the same results. Windows blue screened on both the HDD and the bootable USB. Isn't it too much of a coincidence that it started acting up after the firmware update?
To be clear, it was a firmware update for the BIOS. The page is here for the Aspire 5560G: http://us.acer.com/ac/en/US/content/drivers I am open to more suggestions, I'd really love to get this working again after dropping the $ on Windows 8

Similar Messages

Dell Latitude E6520 fails to boot after Windows Updates

Hello,
I have a Dell Latitude E6520 that is not starting up after Windows updates. It installs updates and requests a reboot, after which it blue screens at the splash logo and reboots again. This goes on indefinitely. The only way to repair it is to boot from
a recovery disk and run:
dism /image:D:\ /cleanup-image /revertpendingactions
This is after running dism /image:D:\ /get-packages and noticing that several updates are still in an "Install_Pending" state. These are the kb's that are pending:
kb2982378
kb2978742
kb2977629
kb2976897
kb2973112
kb2972211
There were other updates, but those showed as installed. I would post the WindowsUpdate.Log, but I do not see a button to attach a file and the log is very long. Here is what I think is relevant towards the end of the log:
2014-09-18 10:52:04:214
496 540
AU Install complete for all calls, reboot needed
2014-09-18 10:52:04:216
496 540
AU Successfully wrote event for AU health state:0
2014-09-18 10:52:04:623
496 8a4
AU UpdateDownloadProperties: 0 download(s) are still in progress.
2014-09-18 10:52:04:623
496 8a4
AU Triggering Offline detection (non-interactive)
2014-09-18 10:52:04:623
496 8a4
AU AU setting pending client directive to 'Reboot Pending'
2014-09-18 10:52:04:623
496 8a4
AU Changing existing AU client directive from 'Progress Ux' to 'Reboot Pending', session id = 0x1
2014-09-18 10:52:04:625
496 8a4
AU Successfully wrote event for AU health state:0
2014-09-18 10:52:04:625
496 1668
AU #############
2014-09-18 10:52:04:625
496 1668
AU ## START ## AU: Search for updates
2014-09-18 10:52:04:625
496 1668
AU #########
2014-09-18 10:52:04:626
496 1668
AU <<## SUBMITTED ## AU: Search for updates [CallId = {7C1069F1-2D57-421E-A378-38DE401BF9F1}]
2014-09-18 10:52:04:626
496 166c
Agent *************
2014-09-18 10:52:04:626
496 166c
Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates]
2014-09-18 10:52:04:626
496 166c
Agent *********
2014-09-18 10:52:04:626
496 166c
Agent * Online = No; Ignore download priority = No
2014-09-18 10:52:04:626
496 166c
Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0
and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-09-18 10:52:04:626
496 166c
Agent * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed
2014-09-18 10:52:04:626
496 166c
Agent * Search Scope = {Machine}
2014-09-18 10:52:05:210
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:07:170
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:09:475
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:09:569
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:11:590
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:14:999
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:16:887
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:18:753
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:19:623
496 1668
Misc WARNING: IsSessionNonstandardUI: session 65536 is an unknown session type 0; treating it as a standard session
2014-09-18 10:52:20:673
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:22:573
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:22:773
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:24:464
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:24:651
496 1668
AU AU received handle event
2014-09-18 10:52:26:366
496 166c
Handler Using CBS interface ICbsSession7
2014-09-18 10:52:27:520
496 1668
Shutdwn user declined update at shutdown
2014-09-18 10:52:27:520
496 1668
AU Successfully wrote event for AU health state:0
2014-09-18 10:52:27:520
496 1668
AU AU initiates service shutdown
2014-09-18 10:52:27:520
496 1668
AU ########### AU: Uninitializing Automatic Updates ###########
2014-09-18 10:52:28:206
496 166c
Agent * WARNING: Exit code = 0x8024000B
2014-09-18 10:52:28:206
496 166c
Agent *********
2014-09-18 10:52:28:206
496 166c
Agent ** END ** Agent: Finding updates [CallerId = AutomaticUpdates]
2014-09-18 10:52:28:206
496 166c
Agent *************
2014-09-18 10:52:28:206
496 166c
Agent WARNING: WU client failed Searching for update with error 0x8024000b
2014-09-18 10:52:28:253
496 1668
Report REPORT EVENT: {62FF14E3-DDBE-4DDC-BE90-12B98EC74605}
2014-09-18 10:52:04:216-0600 1
193 102
{00000000-0000-0000-0000-000000000000}
0 0 AutomaticUpdates
Success Content Install
Restart Required: To complete the installation of the following updates, the computer must be restarted. Until this computer has been restarted, Windows cannot search for or download new updates: - Security Update for Windows 7 for x64-based Systems
(KB2982378) - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2973112) - Security Update for Windows 7 for x64-based Systems (KB2976897) - Security Update for Windows 7 for x64-based Systems
(KB2918614) - Cumulative Security Update for Internet Explorer 9 for Windows 7 for x64-based Systems (KB2977629) - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2972211) - Security Update
for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2937610) - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2894844) - Security Update
for Windows 7 for x64-based Systems (KB2978742)
2014-09-18 10:52:28:253
496 1668
Report CWERReporter finishing event handling. (00000000)
2014-09-18 10:52:28:253
496 1668
Report CWERReporter finishing event handling. (00000000)
2014-09-18 10:52:28:425
496 1668
Service *********
2014-09-18 10:52:28:425
496 1668
Service ** END ** Service: Service exit [Exit code = 0x240001]
2014-09-18 10:52:28:425
496 1668
Service *************
Please let me know if there is a better way of attaching the log to this post and thank you in advance for any help.

Hi ChristianBoman,
We could use the OneDrive to upload the log and then paste the shared link here. For more information, please refer to the following article.
http://windows.microsoft.com/en-us/onedrive/share-file-folder
for the update error 0x8024000b, please refer to the following article.
http://windows.microsoft.com/en-us/windows/windows-update-error-8024000b#1TC=windows-7
Please take the following steps:
1. Run the Windows Update Troubleshooter.
2. Click the Start button , type Run in the search box, and then, in the results list, click Run.
3. Copy the following text, and then paste it into the Run text box:
Cmd /c ren %systemroot%\System32\Spupdsvc.exe Spupdsvc.old
4. Click OK.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

MacBook Pro Won't Boot after Firmware Update

So I just upgraded to a MacBook Pro which came in the mail yesterday. I removed the Apple-installed HD and swapped it out for a bigger, faster HD. I installed OS X from scratch, imported everything from my Time Machine backup during the Setup Assistant, and then started installing updates. Everything was running swimmingly until the last updates.
What happened is when I rebooted my MacBook Pro and logged in after a series of updates, I got presented with both a Bluetooth update and a Firmware update at the same time. Both required a restart so I thought I would kill two birds with one stone. I installed the Bluetooth update, and then when it asked to reset I installed the Firmware update instead. However, the firmware update didn't behave as advertised because instead of shutting the MacBook Pro completely down, it restarted and then started installing the firmware update.
Ever since the firmware update (which I think installed correctly but don't know how to verify), I cannot boot my MacBook Pro. Using the OS X install DVD I can view my firmware version using System Profiler, and the number it is reporting is MBP53.00A.B03.
I have tried booting in verbose mode to try and get a feel for the problem, and it eventually hangs on an infinite loop saying something about not being able to find something on disk0s2.
I also thought I would fix the problem by doing an Archive and Install, but it quit at the very beginning of installing with the error "unknown error".
Also I thought I would format the disk with Disk Utility and then try installing again, but Disk Utility reports that it in unable to unmount the volume.
Any help you can provide would be greatly appreciated. Thanks!
-- Update --
Remember how I'm unable to unmount the drive? I force unmounted it and then used Disk Utility to repair the volume, but still no luck.
I think the key to the problem is this new HD I put in runs at 3 Gbps. I think I read somewhere that the new MacBook Pro's don't support that.
I think next I should try swapping out the new HD in my MacBook Pro with the one it originally came with. What do you think?

I, too, have a brand new MBP 15" that I put an Intel X25 in. At the 1.5 (Prior to Firmware Update) setting, it worked fine. I rant the Firmware Update, all looked fine, but the drive is no longer able to be seen.
Flash the PRAM, per other suggestions to no avail. Boot off of the DVD and disk utility nor Profiler sees the drive.
Replace the drive with the stock that came with the MBP (which I had never even used) and it works.
Put the Intel X25 into a Windows machine and it works fine. Reformatted it (in windows) and put it back into my MBP. Still not able to see it (from the Disk utility after booting off the DVD).
Intel's firmware for the drive says its up-to-date (new drive) and if I attempt to "re-run" the Mac Firmware Update, it says that the machine is already up-to-date.
Seems odd that it worked before an now it doesn't. Also seems odd that the X25 works in other machines. And that my MBP works just fine with the stock Hitachi 7200 320GB drive.
Ideas? Intel says to call Apple Support. Not sure what I can say to them.

MacBookPro won't boot after firmware update; superdrive spins forever

I got my brother to switch to mac recently, but his MacBookPro has stopped booting. He told me that he ran a software update, in fact he said specifically "firmware update" on his CoreDuo MacBookPro, and as a result the machine does not boot. Instead it struggles to power on when the power button is pushed, and nothing happens except for a spinning up of the superdrive. It continues on like this until he holds the power button down again, stopping the spin.
As he put it, he ran a "firmware update" (sounds strange to me) and was told to restart, so he clicked restart. He was later instructed to do a hard restart, holding down the power key. He did so and has since fallen into the spinning drive problem, with no hints as to any cause.
Does anyone recognize this, and could someone please suggest solutions for trouble shooting? Thanks in advance. OS 10.4.x

This sounds like he got a kernel panic, as my FAQ* explains:
http://www.macmaps.com/kernelpanic.html
* links to my FAQ may generate me some compensation.

Sunfire X4150 fails to Boot after ILOM update to 3.0.3.30

After update from ELOM to ILOM and during update of ILOM from 2.0.2.6 to 3.0.3.30, system shutdown, and no boot anymore.
Turning on the system, later, I get the following erro, analysing the SP event log:
ID = 29 : 06/23/2009 : 15:46:11 : System Firmware Error : sensor number = 0x00 : BIOS corruption detected
The SP had gracefull update, but BIOS seems to be corrupted.
Any suggestions, please? How can I recover BIOS, or even, make the system work again?
Bruno Simioni

[SOLVED]
Downgrading the SP and consecutively the BIOS, server is online again.
Download SP and BIOS Firmware from Sun Fire X4150 & X4250 Software Supplemental 2.2.2, at Sunfire x4150 server downloads page, and, downgrade the 3.0.3.30 SP/BIOS to 2.2.2 version.
I really hope that an future version of 3.0 Tools and Drivers DVD makes Sunfire x4150 works fine.
Bruno.

Kt4v , Barracuda failing Windows boot after bios update

Hello
I have KT4V , i had bios 6712 v1.7 installed. I bought today Sempron 3000+ and I wanted to make it works so first i downloaded Bios update "1c0"(latest one) version and flashed my bios . Everything went fine , i restarted PC , Bios asked me to for default settings i pushed F1 , and everything was going fine (still with old CPU Athlon 2000+) , Windows started to boot , and after 2 sec of Windows getting load(Screen with blue load bar appeared for 1-2 second) RESTART , i was confused .
I installed 1.7 Bios(my old one) and still the same. Trying to find out what hapenned i unpluged my Secondary Disk (Primary SLAVE - Barracuda 120GB 7200.7) , and everything was working , windows loaded from my Primary master like always .
Everytime i plug in the Barracuda windows is restaring during boot.
What is going on ? PLZ HELP , Try to imagine how mad i`am with new CPU at my desk :((((
P.S.I made all combinations with Slave , MAster , another data cables , another supply cables . Still nothing

Quote
boot from your windows CD, and attempt a repair install of windows. clearing CMOS / updating BIOS has probably changed some settings that windows disagrees with
Repairing a Windows installation
done . Result - none , still restarting when loading the windows with Secondary Disk.
Quote
I'm not sure, have you cleared CMOS? Power off, unplug power cable, wait a minute or three, move jumper, move jumper back, power cable in and power on. And don't forget to set time and date.
done , result - none , i changed jumper settings and have been waiting for 2 minutes.
Quote
KT4V supports 333 FSB, so why did you have to upgrade Bios ? As Fred says, after each change in Bios ( upwards/downwards) you should clear CMOS.
Kt4v support FSB 333 , but it dont support all CPU , thats why there is a latest patch Quote
-Fix system reports incorrect message for AMD 3200+ CPU.
-Support Sempron L2 512K 3000+ CPU.
And I`am still with Athlon 2000+ , because my disk dont go with windows.
I unnistalles Alcohol 120% , i thought that it could be letters of drive conflict , but no :(
Bios detect harddisk perfectly .
Have no more ideas what to do :(

M1212nf fails to initialize after firmware update

Hello,
I have the same problem. The printer keeps re-initializing. Please note that this only happens when we connect it to the ethernet cable. We have replaced cables, switches already, and other devices have no issues on this connection.
Any help would be appreciated

Hi Yeronimo,
Welcome to the HP Support Forums! I understand your HP Laserjet M1212nf MFP fails to initialize, this happens when you plug in the ethernet.
I have sent a Private message on the Forums. Please go to your Userpage to the right of your Username you will see you inbox.
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

ACER ASPIRE 5560G BIOS ISSUE

I purchased a Acer Aspire 5560g yesterday second hand , lappy worked great. Was updating all the drivers one of which was the BIOS. The install went through and then upon reboot the machine Black Screened. No HDD activity no display. Just a solid Blue light on front bezel fan running. Connected to external monitor and still nothing. From all Ive read it sounds like the BIOS installed hosed. Can someone PLEASE give me a good step by step on how to reflash the BIOS on this machine using a USB drive? I have also reset the cmos battery and reseated the ram.

Hello Guys, Even I had a similar problem. I was planning to take it to service center. But just wanted to try once more so searched in the community and got this thread.My situation is I changed my RAM 2 months ago from 3GB to 8GB on my 5830TG. It was working fine till last couple of weeks until I made one change in BIOS setting and then I tried rebooting then I don't get any screen. my Hardisk looks like it was running. I never got to BIOS screen at all. I got scared & din't know what to do. After reading this post I replaced my new ram with the old once which I had it with me. My laptop booted properly. Then I removed the old ones & added both the new RAM's then the laptop did not boot. Suspecting that one of the RAM must have gone non functional I tried one by one. Both worked fine. Finally I had to insert the RAM properly. Insert it little hard so that it sat fine in the slot. I also reset my BIOS just in case. Great post guys, it helped my try once. You don't know how much time and money I saved :-) Thanks a ton.

Macbook pro won't boot after installing update 10.9.3

macbook pro won't boot after installing update 10.9.3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Leopard USB install no longer boots after software update

Hi all,
I have recently installed Leopard onto a USB partition in order to perform maintenance on my main Leopard installation. Installation proceeds without a problem however after downloading software updates the USB partition will not boot successfully, despite there being no problems with the disk / volume structures / apparently anything at all. In desperation I also tried to install Tiger, which worked, however I have the same problem after updating - it will not boot! I don't think my hardware is at fault - Techtool Pro tells me all is in order.
Has anyone had this problem and if so, how did you fix it?
Thanks,
Jason

I just installed Leopard onto a USB 2.0 external hard drive for a dual-boot. It booted fine at 10.5.1 but is taking ridiculously long to boot after 10.5.2 (I just got it to finally boot after the update while waiting more than 40 minutes!).
It seems that you may want to attempt booting several times - maybe turning off the machine in between or booting to the internal OS first and then to the external. Can't help you much beyond that as this is my introductory experience with this mess.

Data recovery after firmware update

Hi guys,
does anyone know it it is possible to recover data after firmware update in N8? some data are preserved (videos) and some are lost (photos).
thx.

if you didn't backup them, there is no way to recover them
Greece Nokia X6 RM-559 v40.0.002

3014 error i can't restore ipad after firmware update attempt

3014 error i can't restore ipad after firmware update attempt

See this thread with the same question.
https://discussions.apple.com/thread/5045573?tstart=0

After firmware update to V2.0.03, the web UI dos not look right. (WRT160 V2)

Hi
After firmware update from V2.0.01 to V2.0.03, the web UI dos not look right.
I can't see menus, just version number and the basic setup page.
Router Linksys WRT160 v2.
Allan

Hi
Thanks for the reply.
I't works ok now.
Thanks again.
Allan

Restoring after firmware update - Ways :)

Hi All,
Nowadays we are receiving quite a few complaints that customers are unable to restore the application after updating their firmware. I would like all to discuss to come up with some ways to restore their applications after firmware update.
Before updating firmware
Customer can backup his phone using Nokia PC Suite's Content Copier application.
He can store his Contacts and Messages using Nokia Communication Centre as .csv file or .txt file.
For his Contacts he can sync with pc suite supported sync applications.
Messages he can store in Memory card and he can make a backup of memory card in PC.
If he is using Nokia PC Suite for his Multimedia items he can use Image Store if he is using Nokia PC Suite or Nokia Photos if he is using Nokia OVI Suite.
For Music he can use Nokia Music Manager or Nokia Music.
Once after updating his firmware, if he is unable to restore he can get those from above said applications.
If his calendar entries are not restored(as in case of some of Nokia e 71s and Nokia N 95/95 8 GBs), for God's sake if he has got one more similar device(or device having switch application on phone), he can restore the backup file to another phone having switch application, then he can transfer his data (Contacts, Calenders etc ) to his original phone
Dear Forum members, if you have got any other work around please let me know regarding the same, which will help our customers

Hi,
If you have issue in Nokia PC Suites, [subject to your phone's compatibility with Nokia OVI Suite 2.0.0.10 ],
you can install Nokia OVI Suite 2.0.0.10 and check if you can take backup and restore it later.
Also i would suggest to use USB for taking backup, since it will be faster than Bluetooth. Also you can select one category at one time(say backup contacts alone, then Calendar, then messages etc and so on ....)
Its better to skip memory card backup while backup-ing other Phone data for faster backup. Memory card backup can be done separtely(since it wont be affetcted while updating firmware, users can safely remove memory card while updating firmware)
Nowadays though recent phones has got UDP(User Data Prevention i.e., even if you update your phone's firmware, your data wont get erased ), still it is recommended to backup your phone data.
Hope this could help
I welcome our experts to add more details related to this topic.

Problems after firmware update 52.0.007

Hi,
I got my phone back after the shop fixed a problem and updated the firmware to the latest version 52.0.007.
But now I have following problems:
I can't get the calendar anymore to show up on the homescreen, even after checking the checkbox to do so
The Radio app. is gone
Does anyone has a solution for this?
Iwan

It may sound crazy but sometimes you need to "hard reset" device after firmware update (beware all data erased) by keying in *#7370# followed by 12345 (default Nokia lock code unless altered by yourself). Sometimes UDP = User Data Prersevation feature of 5800XM can carry over corrupt entries when updating.
Happy to have helped forum with a Support Ratio = 42.5

Acer aspire 5560g Failing to boot after Firmware update

Similar Messages

Maybe you are looking for