Activating HTTPS services causes Error message

Hi,
I am trying to activate HTTPS service in ICM Monitor GOTO > Service > Activate
and getting Operation failed message with rc=1. Any idea please let me know step by step to activate HTTPS services.
Thanks in advance
Regards
Srinivas

to enable HTTPS you have to do the following steps explained in this link
http://help.sap.com/saphelp_nw2004s/helpdata/en/65/6a563cef658a06e10000000a11405a/frameset.htm
Regards
Raja

Similar Messages

Service Battery error message for a battery that looks ok

Hello,
I have a 13 inch Macbook Pro with model number 5,5 and after upgrading my hard drive to a WD scorpio black 750GB and also adding 8 GB of Kingston memory I get a Service Battery error message. My OS is 10.6.8. The strange is that my battery is in a fairly good condition. I did check with coconut battery and it looks ok. I also add a print screen.
Does anyone knows how can I remove this error message ?
Do I have to replace my battery ?

Service battery means replace battery as soon as possible.
Reset SMC and see whether it changes the notification.
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Best.

CS5 Service Manager error message?

I keep getting the CS5 service manager error message - ordinal not found. Specifically ' the ordinal 3873 could not be located in the dynamic link library LIBEAY32.dll' Any ideas please on how to fix this?

That's very puzzling, but you seem to have an older version of the Adobe Extension Manager for CS5.x. You are on 5.0.x, R_Kelly mentions 5.2.x, and I'm on 5.5.x
Maybe you need to make sure you are updated to Photoshop 12.1 update first, then make sure you are updated to Adobe Extenson Manager 5.5.0.163.
This is the version of the AEM that I have for Photoshop 12.1 (CS5.1) which resides on my Snow Leopard 10.6.8 boot HD:
And this is the version of the AEM that I have for Photoshop 12.1 (CS6) which resides on my Lion 10.7.5 boot HD:
This is the Photoshop 12.1 (CS5.1) application info:

Did recent recommended update cause incompatibility with HP printer, causing error message and printer to print blank pages?

did recent recommended update cause incompatibility with HP printer, causing error message and printer to print blank pages?

Why not contact HP tech support for assistance since they make the printer. While on their site you can look for an updated printer driver. Otherwise, try deleting the current installed driver, reset the print system, then reinstall your printer's driver.
Mac OS X- How to reset the printing system

Error in activating HTTPS service

Hi all,
We have ECC 5.0 based system on which I have exposed one RFC as a web service. I want to use this web service" with HTTPS protocol.
1) When I try to activate the HTTPS service through SMICM, I get the error -
<b>operation failed (rc=1)</b>
I guess 'rc' stands for return code. Any ideas why this happened ?
2) While creating the web service from RFC through wizard, I had kept the basic authentication only. Do I need to select Secure mode there ?
Thanks.

Hi Shankar,
I also suggest you to have look at my reply to the post in the thread below.....
SOAP call failed error
Regards,
Abhy

Check Point VPN-1 Securemote service causes Error 1075: The dependency service does not exist or has been marked for deletion

Has anyone ever managed to solve this one?
We have a problem on Windows 7 SP1 32bit systems.
when we try to start the Check Point VPN-1 Securemote service we get this message:
Error 1075: The dependency service does not exist or has been marked for deletion
When we install a clean Windows 7 from an ISO the checkpoint client without any issues
when we use the same Windows Setup source and install it from SCCM TS - the CheckPoint client doesn't start
the client we're installing is : CP_SeucRemoteSecureClient_NGX_R30_HFA3
which is supported for Win7 x86
other than that there are no special prerequisites for the CheckPoint client. therefore we know the problem is local :/
we tried to isolate and minimize the cause of the issues by trying to see the differences between a clean installation from ISO and a clean installation from SCCM
We know for sure the problem is not from SCCM Client, Programs and Features, Updates, Group Policy
it seems like the configuration is the same but we can't seem to find any online solution about this issue
any suggestions?
thanks
Tamir Levy
Tamir Levy

Hi,
Please check if all the dependencies services are running, if not, please start them:
DNS Server
Remote Procedure Call (RPC)
Netlogon
Server
Workstation
Any error message, please post back.
You can also check solution in this article:
http://support.microsoft.com/kb/269375
Hope these could be helpful.
Kate Li
TechNet Community Support

Adobe updates: I've gotten error messages when trying to download pdfs (very annoying). Read somewhere that mac os has problems with the adobe extensions, thus, causing error messages from adobe. I ignore the updates. Should I?

Hi All,
I have stopped updating adobe software b/c I read that the adobe update software inserts extensions into the mac software system, causing annoying/time consuming error messages when downloading new pdfs. I get adobe update notices 2-3x/week. What do you recommend? I use an iMac OS 10.94.
thanks for your help.

Preview will do all that and is part of the OS.
Mac Basics: Preview app views and edits PDFs and images
With Adobe, if it's working, then it should be fine. See here
http://www.adobe.com/support/downloads/product.jsp?product=10&platform=Macintosh

PHP Form causing error message

Hi,
I am trying to create a page whereby users can fill in their details so I can transfer them into a business card. It's basically just a slightly modified version of my Contact form, which works fine. Yet for some reason it's spitting out this error message:
"Warning: Invalid argument supplied for foreach() in /home/reasona2/public_html/business_cards/pages/businesscard.php on line 17
Warning: Cannot modify header information - headers already sent by (output started at /home/reasona2/public_html/business_cards/pages/businesscard.php:17) in /home/reasona2/public_html/business_cards/pages/businesscard.php on line 29"
I'm using the following HTML:
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8" />
<title>Business Cards</title>
<link href="rpw1.css" rel="stylesheet" type="text/css" />
<script type="text/javascript">

</script>
<form action="businesscard.php" method="post">
</head>
<body onload="MM_preloadImages('buttons/home2.png','buttons/services2.png','buttons/prices2.png ','buttons/examples2.png','buttons/contact2.png','business_cards/classic_contemporary_whit e.jpg','business_cards/classic_contemporary_black.jpg','business_cards/classic_contemporar y_cream.jpg')">
<div id="header"><img src="header_background.png" width="850" height="27" /></div>
<div id="wrapper">
<div id="banner">
    <div id="phone">
      <p class="bold_centre">Call us now on:</p>
      <p><img src="phone.png" width="16" height="13" /> 0845 567 413</p>
    </div>
</div>
<div id="menu"><a href="home.html" onmouseout="MM_swapImgRestore()" onmouseover="MM_swapImage('Home','','buttons/home2.png',1)"><img src="buttons/home.png" name="Home" width="116" height="40" border="0" id="Home" /></a><a href="services.html" onmouseout="MM_swapImgRestore()" onmouseover="MM_swapImage('Services','','buttons/services2.png',1)"><img src="buttons/services.png" name="Services" width="116" height="40" border="0" id="Services" /></a><a href="prices.html" onmouseout="MM_swapImgRestore()" onmouseover="MM_swapImage('Prices','','buttons/prices2.png',1)"><img src="buttons/prices.png" name="Prices" width="116" height="40" border="0" id="Prices" /></a><a href="examples.html" onmouseout="MM_swapImgRestore()" onmouseover="MM_swapImage('Examples','','buttons/examples2.png',1)"><img src="buttons/examples.png" name="Examples" width="116" height="40" border="0" id="Examples" /></a><a href="jobs.html" onmouseout="MM_swapImgRestore()" onmouseover="MM_swapImage('Jobs','','buttons/jobs2.png',0)"><img src="buttons/jobs.png" name="Jobs" width="116" height="40" border="0" id="Jobs" /></a><a href="contact.html" onmouseout="MM_swapImgRestore()" onmouseover="MM_swapImage('Contact','','buttons/contact2.png',1)"><img src="buttons/contact.png" name="Contact" width="116" height="40" border="0" id="Contact" /></a>
<p> </p>
</div>
<div id="main">
    <div id="page_header">
    <h2>Classic: Contemporary</h2>
    </div>
    <div id="card_gallery_div">
      <div id="card_main"><img src="business_cards/classic_contemporary_white.jpg" name="card_large" width="378" height="529" id="card_large" /></div>
      <div id="card_description">
        <p>Description of card to go here</p>
      </div>
      <div id="card_choices">
        <form action="" method="post" enctype="multipart/form-data" name="form2" id="form2">
          <p>Please choose from the following colour options:
            <br />
          </p>
          <p> </p>
          <p><img src="business_cards/colour_blocks/white.jpg" alt="" name="block1" width="40" height="40" id="block1" />
            <input name="radio" type="radio" id="white" onclick="MM_swapImage('card_large','','business_cards/classic_contemporary_white.jpg',1)" value="white" checked="checked" />
            White <img src="business_cards/colour_blocks/black.jpg" alt="" name="block2" width="40" height="40" id="block2" />
            <input name="radio" type="radio" id="black" onclick="MM_swapImage('card_large','','business_cards/classic_contemporary_black.jpg',1)" value="black" />
            Black <img src="business_cards/colour_blocks/cream.jpg" alt="" name="block3" width="40" height="40" id="block3" />
            <input name="radio" type="radio" id="cream" onclick="MM_swapImage('card_large','','business_cards/classic_contemporary_cream.jpg',1)" value="cream" />
          Cream</p>
          <p> </p>
<p>Please provide the following information as you would like it to appear on your new Business Cards:</p>
          <p> </p>
          <p>Name:</p>
          <p>
            <input name="name" type="text" id="name" size="45" />
          </p>
          <p> </p>
          <p>Job Title:</p>
          <p>
            <input name="job" type="text" id="job" size="45" />
          </p>
          <p> </p>
          <p>Tel No:</p>
          <p>
            <input name="phone" type="text" id="phone2" size="45" />
          </p>
          <p> </p>
          <p>Mobile No:</p>
          <p>
            <input name="mobile" type="text" id="mobile" size="45" />
          </p>
          <p> </p>
          <p>Email:</p>
          <p>
            <input name="email" type="text" id="email" size="45" />
          </p>
          <p> </p>
          <p>Website:</p>
          <p>
            <input name="website" type="text" id="website" size="45" />
          </p>
          <p> </p>
          <p>Upload Logo: </p>
          <p>(Please ensure all files are minimum 150dpi)</p>
          <p>
            <input name="file" type="file" id="file" />
          </p>
          <p>           </p>
          <p>
            <input type="submit" name="submit" id="submit" value="Submit" />
          </p>
        </form>
With the following PHP script:
<?php
if(isset($_POST['submit'])) {
$to = "[email protected]";
$subject = "Business Card Order";
$method = $_POST['radio'];
$name_field = $_POST['name'];
$job_field = $_POST['job'];
$phone_field = $_POST['phone'];
$mob_field = $_POST['mobile'];
$email_field = $_POST['email'];
$web_field = $_POST['website'];
$address_field = $_POST['address'];
foreach($_POST['check'] as $value) {
$check_msg .= "\n$value\n";
$body = "Business Card Colour: $method\n\n Name: $name_field\n\n Job Title: $job_field\n\n Phone: $phone_field\n\n Mobile: $mob_field\n\n E-Mail: $email_field\n\n Website: $web_field\n\n Address: $address_field ";
$header="From: $email_field\r\n";
mail($to, $subject, $body,$header);
header("Location: businesscard_thanks.html");
} else {
echo "blarg!";
?>
Can anyone help fix the PHP so the error message goes away?
I'd also like to include an option for users to upload a file so they can supply a logo if they want to. I've already got the HTML side of that sorted, but can anybody advise what to do with the PHP?
Thanks very much in advance!
Oli Corse

The error message is pretty clear:
Warning: Invalid argument supplied for foreach() in /home/reasona2/public_html/business_cards/pages/businesscard.php on line 17
It refers to this section of code:
foreach($_POST['check'] as $value) {
$check_msg .= "\n$value\n";
I can find no form elements with the name check[]. To use foreach, it must be an a valid array.
It's difficult for others to pick through such a morass of code, but one thing I noticed is that you have an opening form tag inside the head of the page. Before asking for help in a forum, it's always a good idea to validate your code.
I'd also like to include an option for users to upload a file so they can supply a logo if they want to. I've already got the HTML side of that sorted, but can anybody advise what to do with the PHP?
There are instructions on how to upload images to a website in the Dreamweaver Cookbook here: http://cookbooks.adobe.com/post_Upload_image_to_website__PHP_-16389.html. The article doesn't cover how to attach the image to an email. The standard PHP mail() function doesn't handle attachments.

Facing the user profile service service failed error message

Hi,
This is prasad, and am facing the below error message while i try to logon to the system with administrative password.
The User Profile Service service failed the logon.
User Profile cannot be loaded.
Can you please help me out how to resolve the above issue as the earliest?
Thanks in advance.
With regards,
Prasad V

This is probablly caused by a virus.. When this happened to me it did work in safe mode. You should disable all start up programs except for the programs needed to start up. TRy unninstalling all of the programs. Do you have more than one user account? I`m guessing you have vista. What I did was reinstall the vista. I had a backup on one partion of the disk and transfered that but it did fail. INStead I ended up with not being able to start it up. I called aacer and they gave me a new bsckup disk. IF you have more than one account then you can easly transfer all the doccuments and redo everything. You may have to get office and all thoose other programs again. I found a lot of extrtra viruses and spyware when I did the scan. So, it may be hard to get back in. JUSt log into safe mode, make an extra account if possile. Good luck!

NI-PAL Service Manager Error Message

Hello Fellow LabVIEW users
I am getting error message everytime I switch on my computer as shown in the attached image file.
1) what is the NI-PAL? I could not find any help topics related to it.
2) Why is this error message shown? Could it be because I changed the PCI port for my GPIB card?
3) How do I overcome this issue? Is it a major problem?
Thanks
mhaque
Attachments:
error message.JPG ‏44 KB

Mhaque,
May be the following link help for u..
http://forums.ni.com/t5/LabVIEW/NI-PAL-service-manager-generate-an-error-at-the-startup-of-the/td-p/...
Siva
Sivaraj M.S
CLD

Activation of Webservices with error message

Hello Experts,
when I try to activate a web service in tr. SE80 I get the error message "No vendor specified". There is no further information to this message and I don't have any idea because in my webservice is no vendor field available. I created the webservice for a remote function module. This function module has only one tables parameter with structure of table MARA and no further coding.
We have SAP ECC 6.0 with SAP_BASIS 700 and patch level 15. I also implemented OSS hints 1166013, 1319014 and 1139107.
Has anybody an idea regarding this error message?
Best regards
Christian

Problem solved... the service must be created via tr. SICF than the activation will be successful without error message.

BT Speedtester: HTTP Status 404 error message

This is a problem extracted from the thread below as it is a separate issue
http://community.bt.com/t5/BT-Infinity/Bt-s-speed-tester/td-p/405819
When trying to use the new Speedtester I get the message below in the banner line.
HTTP Status 404 - /PerformanceTester/applet/progressbar/progressbar.html
If I ignore the message and carry on I get a TEST Error message before any meaningful data is displayed.
The following is general information about the problem.
1.The PC involved is running Windows XP and Internet Explorer 8
2. The problem did not occur with the previous version of the speed tester.
3. Java does not start as it used to.
4. The Speedtester works OK using Firefox on the same PC.
5. When running the Speedtester on a different PC with IE 7 I get the following screen
6. Based on the above it looks as if this check is failing with IE 8 on the original PC but other than the 404 message there is no other indication of this including in the event logs in the PC.
7. At least one other contributor is having this problem.
8. It is not a JAVA problem otherwise Firefox would not work.
9. IE 8 is OK for most other activities so it appears to be an IE8 / New Speedtester problem.
Three final questions
a) Is anyone else having this problem ?
b) Has anyone got a suggestion for the cause?
c) Has anyone got a cure that involves XP and IE8 ? (I already have a work around)
Solved!
Go to Solution.

I have just discovered this thread
http://community.bt.com/t5/BB-Speed-Connection-Issues/bt-speedtest/td-p/409019
Based on the information there I have created a new favorite
http://www.speedtester.bt.com/ that as far as I can see is identical to my previous favorite.
The new one works !!!
The old one still gives the previous 404 error !!!

Drive restriction group policy causes error message when accessing Open and Save As Dialog Boxes on Windows 8.1

We are running Windows 8.1 Pro x86
I am really curious as to why the drive restriction group policy causes the error message to pop up:
"This operation has been cancelled due to restrictions in effect on this computer. Please contact your system administrator."
It does not prevent from actual saving so functionality is not lost but it really annoys our end users and we're getting a lot of complaints. We cannot use the workaround of hiding drives instead of restricting as this still presents security issues. This
is happens when saving (or clicking on a button like "Browse" that opens the 'Open' dialogue box) in all Office 2013 applications, Internet Explorer, Paint, Notepad, and probably most others. I've looked at many forums and no suggestions for workarounds
have succeeded for us to get rid of this error message and in fact, I read a post that stated that someone contacted Microsoft and they said this was by design and there is no workaround. I find this very unfortunate that we either have the choice of compromising
security or annoying our end users. It seems to me like the new dialogue box in Windows 8.1 (and maybe 8?) attempts to access the local drive under the logged in user's account before it actually opens up the dialogue box which conflicts with the group policy
that restricts access to the drive.
Has anyone at all had any luck getting this to go away without removing the restrictions? It seems like the answer is either buried in the Windows code or somewhere in the registry.
Thank you in advance for your time!

Thank you for your time and response! Unfortunately, we have the machine locked down pretty tight (they are public use computers that require heavy restriction) and it is set to restrict all drives so access is limited to the local profile. We did try
testing your method, however, by adding the Desktop as an allowed location in the Office policy (which would not solve the issue for the other applications but was good for a test) using the path %userprofile%\desktop. When choosing that location, it does
not throw the error but unfortunately, it does not remember like it did for your with the E: drive so it still always throws the error when first loading the dialogue box no matter what I do. If you're able to confirm that this is simply by design and we're
just expected to inform our users to click through the errors, then I guess that's the accepted answer. Although, do you think that there might be a registry key value that is set after you save to the E: drive for the first time? Maybe we could set that value
to %userprofile%\desktop if it's doing the redirection after the first save through registry. Thanks again!

Time machine causes error message " Disk not properly ejected" with USB backup drive

I am using iMac OS X Lion and Time Machine causes the error message with a WD 1.5 TB drive in aThermaltake dock, USB. every time I wake up the computer.... Ejection of Time Machine and shut it down and turn opp power to drive causes the error message problem to disappear. What is the solutin?

If it were mine I would replace the drive with another brand. WD drives EHD's tend to have more issues than any other EHD. If you want to continue using it you can try resetting the SMC (may take 2-3 tries) and/or restarting in Safe Mode to reset some caches, it's possible one or more has become corrupt.
SMC RESET
Shut down the computer.
Unplug the computer's power cord and all peripherals.
Press and hold the power button for 5 seconds.
Release the power button.
Attach the computers power cable.
Press the power button to turn on the computer.
PRAM RESET
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

"HP34970A Conf Resistance.vi" causes error message -113

I'm using Labview 6.1 to read voltage, frequency, resistance and temperature readings from an HP34970A (with 34902A 16-channel multiplexer).
Every time the "HP34970A Conf Resistance.vi" is completed it causes the HP34970A to display error -113: "Undefined header. A command was received that is not valid for this instrument. You may have misspelled the command or it may not be a valid command. If you are using the shortened form of this command, remember that it may contain up to four letters. Or you may have inserted an extra colon where one is not required.".
The only thing the vi is supposed to do, is to enable the offset compensation, which it is doing (I tested that with a separate program).
Although t
here is no help file with the NI drivers for the instrument and I'm new to Labview, I would like to know if someone found a workaround for this. It is kind of annoying because the error message is accompanied with a beep of the instrument every 3s.
Thanks.

Thanks for your fast response.
I'm using the latest version of the drivers (I installed everything in the begining of Mai).
I wrote a small vi for NI Spy, just a simple 4 wire resistor measurement with "Conf Resistance.vi" at the beginning.
Unfortunately it is my first time working with LabVIEW and the VISA language, and the syntax looks correct for me. ( But I still get the -113 error.)
Here the processed commands (1 loop):
1. viGetAttribute (0x0015B920,0x3FFF018F,VI_FALSE)
Process ID: 0x0000033C Thread ID: 0x0000041C
Start Time: 14:52:09.127 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
2. viGetAttribute (0x0015B920,0x3FFF018F,VI_FALSE)
Process ID: 0x0000033C Thread ID: 0x0000041C
Start Time: 14:52:09.127 Call Duration: 00:00:00.010
Status: 0 (VI_SUCCESS)
3. viGetAttribute (0x0015B920,0x3FFF018F,VI_FALSE)
Process ID: 0x0000033C Thread ID: 0x0000041C
Start Time: 14:52:09.157 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
4. viGetAttribute (0x0015B920,0x3FFF018F,VI_FALSE)
Process ID: 0x0000033C Thread ID: 0x0000041C
Start Time: 14:52:09.157 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
5. viOpen (0x0015B920,"COM1",0 (0x0),0 (0x0),0x0017CC30)
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.469 Call Duration: 00:00:00.010
Status: 0 (VI_SUCCESS)
6. viGetAttribute (0x0017CC30,0x3FFF0171,4 (0x4))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.479 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
7. viGetAttribute (0x0017CC30,0x3FFF0171,4 (0x4))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.479 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
8. viSetAttribute (0x0017CC30,0x3FFF001A,10000 (0x2710))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.479 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
9. viSetAttribute (0x0017CC30,0x3FFF0021,57600 (0xE100))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.479 Call Duration: 00:00:00.010
Status: 0 (VI_SUCCESS)
10. viSetAttribute (0x0017CC30,0x3FFF0025,1 (0x1))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.489 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
11. viWrite (0x0017CC30,"*RST.",5 (0x5),5 (0x5))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.489 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
12. viWrite (0x0017CC30,"SYSTRES.",10 (0xA),10 (0xA))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.489 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
13. viWrite (0x0017CC30,"*IDN?.",6 (0x6),6 (0x6))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.489 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
14. viRead (0x0017CC30,"HEWLETT-PACKARD,34970...",50 (0x32),32 (0x20))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.489 Call Duration: 00:00:00.370
Status: 0 (VI_SUCCESS)
15. viWrite (0x0017CC30,"*RST.",5 (0x5),5 (0x5))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.859 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
16. viWrite (0x0017CC30,"SYSTRES.",10 (0xA),10 (0xA))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:17.859 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
17. viWrite (0x0017CC30,"FUNC "RES", (@);EN...",122 (0x7A),122 (0x7A))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:18.781 Call Duration: 00:00:00.020
Status: 0 (VI_SUCCESS)
18. viWrite (0x0017CC30,"MEAS:FRES? AUTO, (@101).",24 (0x18),24 (0x18))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:19.742 Call Duration: 00:00:00.010
Status: 0 (VI_SUCCESS)
19. viSetAttribute (0x0017CC30,0x3FFF001A,320000 (0x4E200))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:19.752 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
20. viRead (0x0017CC30,"+1.08185990E+02..",500 (0x1F4),17 (0x11))
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:19.752 Call Duration: 00:00:00.130
Status: 0 (VI_SUCCESS)
21. viClose (0x0017CC30)
Process ID: 0x0000033C Thread ID: 0x0000042C
Start Time: 14:52:21.214 Call Duration: 00:00:00.000
Status: 0 (VI_SUCCESS)
Thanks,
Dirk

Activating HTTPS services causes Error message

Similar Messages

Maybe you are looking for