AiroNet 1130AG and 802.11b devices

I cannot seem to get this darn AiroNet 1130AG AP to allow 'b' devices. All of the examples I have found are not the same GUI interface as what this one has. I just upgraded the IOS to the lastest as of 5/6/2009. How do I get this to work.

can you post the config ..
Also are you allowing all the data rates 1,2,5,11 etc ?
Also did you check your client, can it attach to other access points using B

Similar Messages

  • MSI\'s Bluetooth and 802.11b combo module

    From CSR's e-news service I know about MSI's Bluetooth and 802.11b combo module:
    "MSI's Bluetooth and 802.11b combo module using CSR's BlueCore Cambridge, UK - November 4, 2002 - CSR (Cambridge Silicon Radio) has announced
    that Taiwanese motherboard manufacturer Micro-Star International (MSI(TM)) has launched a wireless module combining both Bluetooth and Wireless LAN protocol
    802.11b. The module is being supplied with the company's mainboard 845PE Max2 and is available now in all major markets around the world".
    Where I can receive the detailed information concerning to this module?

    Quote
    Originally posted by wonkanoby
    http://www.msi.com.tw/program/products/per/per/pro_per_list.php?kind=7&CHIP=39&NAME=Bluetooth
    This address (http://www.msi.com.tw/program/products/p. *NAME=Bluetooth)
    describes two PC2PC BlueTooth the device (Bluetooth Transceiving Key (MS-6967) and
     Bluetooth Transceiving Module (MS-6968)).
    Me interests " wireless module combining both Bluetooth and Wireless LAN protocol
    802.11b ". That it is?

  • WLSE and 802.11b/g Interference Detected

    Hello there!
    I have 60 AP-1231G units over 8 sites running WDS in conjunction with a WLSE on 2.12FC firmware. A week ago, every AP on every site went into fault mode reporting "802.11b/g Interference Detected". Not matter what I try (rebooting APs, WLSE, clearing fault, upgrade to v2.13, so on) I can't get rid of this issue... Apparently every single AP over 8 sites (located in a radius of 60 miles) detected Interference all at the same time.... ???????
    Has any one seen this before and know how to deal with this?
    Best Regards,
    Richard

    Hi Richard,
    maybe you are facing a problem with CSCsd63242:
    Symptom:
    If the 'Fault Severity' of the "Interference Detection" settings under Network Wide IDS settings, is modified, and later if APs are moved from the 'Default IDS profile' to any other newly created IDS profile, the interference faults that are raised
    on those APs, are not raised with the correct severity that the user modified. For example, if one enables this setting and changes the fault severity to P3, and if some APs are moved from the 'Default IDS profile' to a new IDS profile, when the faul
    ts are raised on these APs, the severity wouldn't be P3, but would be P1- the original severity of the fault.
    Whereas, had the APs not been moved from the 'Default IDS profile' to any other profile, the faults raised would have been with correct severity - P3.
    Conditions:
    This will happen in all pre 2.13.1 releases of WLSE, and only when the APs are moved to IDS profiles which are created new, or (are moved) to copies of IDS profiles which are created new. This will not happen when all the APs either belong to
    the 'Default IDS profile' or are moved to copies of the 'Default IDS profile'.
    Workaround:
    Modify the fault severity first. Then copy the the 'Default IDS Profile' to new ones and modify them in whatever way. Now, even if APs are assigned to these profiles, the correct severity will be used when the fault will be raised. Now, once the co
    pies are created, don't modify the severity ever again! If you do, the new severity will be used only for the faults raised on APs belonging to the 'Default IDS profile', but the old severity will be used for the faults raised on APs belonging to the
    copied IDS profiles.
    Also, don't create new IDS profiles and assign devices to them, always create copies from the 'Default IDS profile'.
    Further Problem Description:
    The 'Network wide IDS settings' are supposed to be independent of any IDS profile. But, they are not behaving in this way. For more details, see workaround section above.
    The problem is resolved in release 2.13.1 and wouldn't occurr even if the APs are assigned to newly created profiles (they don't have to be copies of the 'Default IDS Profile'). The upgrade scenarion is also taken care of - If this problem was faced
    in releases prev to 2.13.1, when WLSE is upgraded from rel 2.13 to 2.13.1, this defect wouldn't occurr again.
    Hope that helps.
    Best regards,
    Frank

  • Broadcasting in 802.11n (a compatible) AND 802.11b/g

    I have a Time Capsule and an Airport Express and I'm wondering if I could do the following (but not sure if/how)...
    1. Broadcast my cable broadband connection in 802.11n (a compatible) from the Time Capsule.
    2. Extend the network using my Airport Express but in 802.11b/g.
    I want to do this because my xBox works far better on n/a, but of course my iPhone doesn't work at all unless it's on b/g (which is quite annoying).
    Is this possible? And if so, is there any issue about the respective devices differentiate between the n/a and b/g?s

    This is the exact command that you need to use.
    The throughput with the aggregation is a bit higher than that without aggregation.
    HTH
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Having both 802.11g and 802.11n devices on a new dual-band AEBS

    Although I don't own a dual-band AEBS yet, I'm thinking I might be in the market for one. I just moved into a new apartment complex where the 2.4GHz frequency is saturated with over 30 wireless networks in range of my unit. I'm thinking that the 5GHz frequency would be much less crowded, and am thus considering getting a dual-band AEBS.
    I have the following equipment on my home network:
    1 Power Mac G5 (uses wired ethernet)
    2 MacBooks (use 802.11n)
    1 iPhone (uses 802.11g)
    1 PlayStation 3 (uses 802.11g)
    My question is (and I keep finding conflicting information on this topic) will the iPhone and the PS3 slow down the MacBooks from 802.11n speed to 802.11g speed when they are connected to the dual-band AEBS? If so, can this be avoided by running 2 routers with two separate SSIDs (one in 802.11n only mode, and the other in 802.11g only mode)?
    Sorry if this is a repeat question, but the fine print on Apple's product page says that the dual-band AEBS will be slowed down when a 802.11g device joins, but I have heard people say otherwise elsewhere.
    Thanks.

    So with the new dual-band AEBS, it is possible to create two different SSIDs (one 5GHz 802.11n and one 2.4GHz 802.11g) and have those two networks seamlessly joined for file/printer sharing as well as both run at their maximum speeds.
    To the best of my knowledge, being that I just got one a few days ago and haven't "experimented" fully yet, I believe the answer is yes to all counts. I'm sure if others have had the opportunity to check out all of the features that this new model has to offer, they will certainly chime in.

  • How to extend new TC - 802.11n with AEBSn's  and 802.11b/g with AEBS's

    Regrets if this has already been answered, but I cannot seem to find it.
    Just purchase a new 1TB TC - have set it up OK and it seems to be running fine. I am trying to extend both networks, n and b/g, with different devices - newer AEBSn's and regular older AEBS's.
    I can see from the instructions the AEBSn's are set up with "Extending the network", but how are the b/g AEBS's set up?
    In my old pre-TC set up, I had dual band networks set up using an AEBSn, and the AEBS's were set up to extend the b/g network using WDS. I cannot figure out how to set them up with this new dual band Time Capsule.
    And BTW, I laso have old b/g AEX's set up to stream music, and have set them up as "Join a wireless network" - I think this is correct.
    TIA.

    I may need to be offline for awhile, so I will go ahead and post the "how to" for the 4 AEBS devices that will be configured to "extend a wireless network".
    Each “n” AEBS will be setup exactly the same, except that you will probably want to give each AEBS a separate name and/or number to keep things straight.
    Rather than using wireless to configure the devices, I find that it will usually help to temporarily connect an ethernet cable from your computer to one of the LAN <-> ports on the AEBS to help with the configuration with AirPort Utility. You can disconnect the ethernet cable when you have the AEBS configured and updated.
    I suggest that you configure each device and then place it in a temporary position to test to make sure it is "extending" and working correctly. If you turn off the wireless on your computer and plug your computer into one of the ethernet ports on the AEBS and get an internet connection, then you know that it’s “extending” and working correctly.
    Or, if you have wireless active on your computer, you can also hold down the "option" key on your computer and click on the AirPort icon at the top of the screen. You will see the AirPort ID of the device that the computer is connected to, which should be the AEBS you are testing if the computer is close to the device.
    Configure all 4 “n” AEBS devices and test them, then you can locate them where they are needed. Try to use the hub and wheel model as much as possible for best results. Unfortunately, the "extend" setup may not work well if you have the Time Capsule at one end of the house rather than a reasonably central location.
    AirPort Utility > Manual Setup
    Click the Base Station tab to name the device, etc
    Click the Wireless tab
    Wireless Mode = Extend a wireless network
    Wireless Network Name=The name of the Time Capsule network should appear as a choice to extend
    Put a check mark next to Allow wireless clients
    Wireless Security = Exact setting as the Time Capsule
    Wireless Password = Exact setting as the Time Capsule
    Update to save changes
    I think that you can probably get the 3 AirPort Express devices configured to “join” the Time Capsule wireless network, so that should take care of AirTunes streaming on those devices.
    The older AirPort Base Stations and AirPort Extreme(s) will need to connect using ethernet if you want to use them since they cannot be configured to “extend” a wireless network like the “n” AEBS devices.
    Message was edited by: Bob Timmons

  • J2ME and 802.11b?

    I'm planning to make wireless P2P between PDAs and PC using WiFi and J2ME.
    Are there any issues between J2ME and WiFi that I should know about?
    How difficult is it to make such a network?
    Is J2ME compatible to most PDAs?
    Can J2ME be used for an app on a PC?
    I need all the help I can get. I am at your mercy. =)

    Are there any issues between J2ME and WiFi that I
    should know about?I'm guessing you will be using Sockets, Nokia phones, and sockets don't get on.
    Is J2ME compatible to most PDAs?Sun have a PalmOS J2ME JRE, Symbian/Psion have a J2ME JRE and I've seen a MS Windows CE/PocketPC J2ME JRE about, Google knows all.
    Can J2ME be used for an app on a PC?You would be better off writing a generic back end, then a J2ME LCDUI interface and a Swing/AWT/SWT interface, but I've seen the javax.mobileedition packages about for J2SE, or you could use a phone emulator.
    I need all the help I can get. I am at your mercy.
    =)I think one of the optional packages does P2P, I can't remember which thou.

  • Photosmart C7250 wireless 802.11b fails

    My new C7250 works well with USB and wired ethernet, but fails miserably (prints slowly, if at all) on my wireless 802.11b network.  All other devices work well on my wireless network.  I've spent many hours with HP and exhausted their first line support.  They supposedly have opened a case but I have heard nothing in a week.  Meanwhile, I took a network trace using WireShark and it shows a large number of retransmissions.  (I'm expert with application/network performance profiling.)  All you have to do is browse to http://192.168.1.xxx/ to test transmission -- don't even need to install drivers or printers to see the errors.  This problem appears to be with wireless support on the C7250.
    Has anyone experienced problems or success with 802.11b on this device?  How about 802.11g?  I would be willing to upgrade my wireless if I knew that it would resolve the problem.
    What does it take to escalate a probem with HP for resolution?

    All 2004 and newer wireless HP Inkjet printers are compatible with 802.11g and 802.11b networks (otherwise we couldn't get 802.11g Wi-Fi certification).  Besides testing for interoperability, we test for a minimum wireless throughput at the TCP layer.
    I'd like to see the internal connectivity report that you can generate by pressing the <setup> and <#> buttons simultaneously.  Scan the report to a memory card, copy it to your PC and post the image here.
    It will tell me information about your wireless network and other networks in the area.
    I have a couple of other questions:
    Does the slow printing go away after a power cycling the printer and then does it return later?
    Does the slow printing go away after a power cycling the wireless-router and then does it return later?
    Are you seeing retransmissions of TCP, 802.3 (ethernet) frames or 802.11 frames?  I wasn't sure at what layer you are sniffing the data at?
    What make and model 802.11b wireless-router are you using?
    Do you have encryption enabled?  Does disabling encryption change the speed of printing?
    How many wireless PC's (Macs?) to you have on your network?  Do they all exhibit slow printing?
    Have you changed the default fragmentation settings of your wireless-router?
    At home, I routinely get 1.5 Mbytes/sec transfer rates between my 802.11g wireless-routers and my HP printers and about 700 Kbytes/sec in 802.11b mode.
    One other thing you can try is to go to the printers internal web page, browse over to the Networking, Wireless, Advanced page and enable the configuration "In an infrastructure network use 802.11b behavior".
    Regards / Jim B
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • Apple TV Seems to be Synching at 802.11b speeds

    Hi folks. I've been kinda frustrated with my Apple TV synching speeds (likes lots of other people apparently) and I thought I'd add my two cents.
    I have a Linksys WRT54G wireless router. All of the devices on my network operate at 802.11g speeds except for my Apple TV. The Activity Monitor on my Mac Mini reports that movies are copying across to the Apple TV at a pretty consistent 1.6 MBPS. So an average 2gb movie is copying in around 20 minutes. If my math is right that 1.6 mega Bytes per second is approximately 11 mega Bits per second, which is just what the max for 802.11b is/was.
    Any clues as to why by Apple TV would seem to think it's a 802.11b device rather than 802.11g. This of course is a bit speculative and yes I have ruled out interference or other weird problems. To reiterate, all of the other devices on my network, including our iPhones are operating at 802.11g speeds of 54 mbps.

    Frank,
    Not an attempt to debate your knowledge, and I don't even have my Apple TV yet but I have had (and currently have) different streaming boxes (Xbox 360, media player set top box [still gives me shivers], etc.) and sometimes network congestion is just a pain...
    Even though everything else operates at "g" speeds, try using just the Apple TV to sync after a fresh restart with all other devices off the network...

  • Does Airport Extreme still function at 802.11ac if an 802.11n device is connected to network?

    I have an Airport Extreme and iPhone 6 which both operate on 802.11ac. I have noticed when an 802.11n device (DVD player) is also connected to my network my connection rate on my iPhone 6 drops to 802.11n rather than the faster 802.11ac. All of the literature I have read states that Airport Extreme is capable of transmitting at both 2.4ghz and 5ghz simultaneously (I have no questions about that), however is Airport Extreme incapable of transmitting to both 802.11ac and 802.11n devices simultaneously? If so, why did I spend all that money on a router that boasts 802.11ac technology but slows to 802.11n if an 802.11n device is connected?

    It should do both at once.. AC is only on 5ghz and I highly doubt the DVD player is using 5ghz.. however you might need to force the phone to connect to 5ghz.. as it will always join the strongest signal not the best or fastest wireless..
    So simply set two wireless names.. eg AE24ghz for the 2.4ghz and AE5ghz for the 5ghz band.. whatever you name it include the freq as it makes it easier to know what is going on.
    Then force the phone to join the 5ghz and it should work just fine at AC speed. Even as the DVD is running on 2.4ghz. Of course if bandwidth is consumed by both and your internet is limited it may reduce your speed to well below N wireless even.

  • Aironet 1140N in mixed mode not working with 802.11b/g Clients

    I have a new Aironet 1140N Access point , the model is number AIR-AP1142N-A-K9, my main problem in that i have Nokia E71 smartphones on the network, but they cannot connect to the Network, the Access Point SSID is not showing on the List of Available Devices if i Scan using the Phone,
    All Laptops are runing Win 7 Pro and they connect quite ok, The phones (8 of them) at HotSpots connects without problems, the Spec says they are compatible with 802.11b/g and the Aironet Access point provides 802.11a/g/n.
    Since the phone has the 802.11g which is compatible with the Access Point, why cant it Pick it? the Access Point is Operating in Mixed Mode.
    Bonnie

    There are basically two "flavors" of WDS that the AirPorts support: static & dynamic.
    o A static WDS allows for a main, relay, and remote base stations in the configuration. This only operates in the 802.11g radio mode. Its advantage is it is well suited when you are trying to cover a considerable linear range ... like a rectangular house where the Internet connection comes in at one of the shorter sides and you want wireless at the other end. The biggest disadvantage of this type of WDS is that for every base station added, you lose half the overall bandwidth.
    o A dynamic WDS allows for only a single main and multiple remotes. Think of a wheel with the main at the center and the remotes as spokes of the wheel. The advantage of this type of WDS is it operates in the 802.11n radio mode and doesn't suffer a significant bandwidth loss like the static version.
    As a minimum, a dynamic WDS requires two 802.11n AirPorts (or Time Capsules). You can create a static WDS with either all 802.11g AirPorts or a mix of 802.11n & 802.11g AirPorts. Note; however, you cannot create a dynamic WDS with mixed mode base stations.

  • Connecting 802.11b/g devices to an 802.11n AirPort network

    I have a Time Capsule with an iMac and a MacBook connected to it. I want to add a Windows laptop to the setup, but it only has 802.11 b/g networking built in. As I understand it, adding an 802.11b or g device to an 802.11n network will slow the network down to the speed of the slower b or g device. What kind of 802.11n device, that is compatible with the AirPort (Broadcom?) chipset, should I get to connect this computer to the network? (The PC does not have a card slot.)
    Would an AirPort Express work in WDS mode, with its Ethernet port connected to the laptop's Ethernet port?

    As I understand it, adding an 802.11b or g device to an 802.11n network will slow the network down to the speed of the slower b or g device.
    Not quite all the way down to 802.11b or g, but there will be a bandwidth degradation for 802.11n clients.
    What kind of 802.11n device, that is compatible with the AirPort (Broadcom?) chipset, should I get to connect this computer to the network?
    A number of vendors, specializing in networking equipment, offer 802.11n USB wireless adapters. I have used a number of Cisco/Linksys products that work just fine with AirPort networking.
    Would an AirPort Express work in WDS mode, with its Ethernet port connected to the laptop's Ethernet port?
    If this AirPort Express Base Station (AX) is a 802.11b/g version, then it would have the same affect as any other 802.11b/g client. In fact, in a WDS, the network will only operate in the 802.11g mode, so you really don't to go that route either. Another option, would be to use a newer 802.11n AX; reconfigure it as a ProxySTA, and use its Ethernet port for the connection to the PC.

  • ISE and non-802.1x devices

    Hi,
    I am looking for some input about how to profile and authorize non-802.1x devices. These devices are mostly barcode scanners connecting wireless with WPA/2. I am not sure how to authenticate them in ISE.
    We have two scenarios.
    1) LAP/WLC with several SSID/VLAN where the devices authenticate with WPA/2.
    2) Autonomous AP with several SSID/VLAN where the devices authenticate with WPA/2.
    There is a posibility to authenticate them on OUI, but I would like to have atleast another condition. Is it possible to use the WPA PSK?
    For the second scenario; is it possible to use autonomus AP and ISE? Barcode scaners need to go to one VLAN and other non802.1x devices to another. My guess is that the config should be somewhat similar to a switch, regarding AAA/RADIUS.
    Have anyone set up ISE with non802.1x devices? What/How did you do?
    Regards
    Philip

    I've quickly tried to authenticate against ISE with Autonomous AP
    No luck, maybe there is a work around but haven't tried as hard or there might not be:
    Failure Reason > Authentication Failure Code Lookup
    Failure Reason :
    11036 The Message-Authenticator RADIUS attribute is invalid
    Generated on:November 14, 2012 11:11:46 AM CST
    Description
    The Message-Authenticator RADIUS attribute is invalid. This maybe because of mismatched Shared Secrets.
    Resolution Steps
    Check whether the Shared Secrets on the AAA Client and ISE Server, match. Ensure that the AAA Client and the network device, have no hardware problems or problems with RADIUS compatibility. Also ensure that the network that connects the device to the ISE, has no hardware problems.

  • Cisco Aironet 1210 AP w/ 802.11b module & WPA2

    Hi
    Currently,I have deployed 1210 AP w/ 802.11b module, are my equipments consider WPA2 compliance ? Or it must be through firmware upgrade for my AP and module, or to re-purchase new AP and/or modules ?

    that's correct. You also need to upgrade the software on the AP. I assume that you have a contract to download the next AP software release from http://www.cisco.com

  • AX Test using PB G4,  MacBook and MBP - is it the AX or 802.11b?

    I recently bought an Airport Express so I could stream iTunes to the main stereo. iTunes keeps cutting out. I'm using a NetGear MR314 802.11b - also tried a linksys 802.11b and same results.
    At first I thought it might be the distance of the AX from the wifi router...so I now I have all 3 laptops and the AX within 5-7 feet of the wifi router and still iTunes cuts out.
    I'm completely baffled.
    I confirmed AX has the latest FW v6.3. I tried turning interference robustness on and off.
    There isn't much to change config wise on the AX or the Netgear.
    I find it hard to believe that streaming iTunes over 802.11b is more than it can handle. No other traffic is occurring over the wireless during my test.
    Thoughts on additional testing?

    Additional testing...
    From each laptop I'm pinging the router and www.google.com.
    The G4 has a consistent response of 3-5ms (router) and 75-80ms (google) where the other two (MB and MBP) have responses all over the field. 4ms to 1000ms to router and 70-1800ms responses to google. So something is clearly different between the airport cards of the G4 and the MB/MBP and the way they interact with the Netgear.
    So I would only assume the AX would have similar responses like the MB/MBP since it is probably the same type of airport technology and not the older type in the G4 (just speculation)
    The above is not even streaming iTunes.
    When I stream iTunes even the G4 response times go up - 90ms to the router (vs 3-5ms w/out iTunes streaming) and 138 ms to google (vs 75-80ms w/out iTunes streaming).
    So what conclusions to draw?
    1) Airport cards in the MB & MBP have an issue communicating with the Netgear yet the G4 doesn't
    So what about the AX?
    If I'm directly connected (ethernet) to the Netgear my response times don't change and they are 1ms to the router and 67ms to google - so the Netgear itself isn't having issues...only the wifi between it and the laptops.

Maybe you are looking for