Airport Extreme Base Station and Airport Express network
Should I be configuring my Airport Express to extend the network of the Airport Extreme Base station or to be joining that network?
"Extend" if you want the Express to provide more wireless coverage in the area where it is located. This is a good choice for most users.
"Join" if you you don't need any additional wireless coverage in that area.
In both configurations above.....AirTunes is enabled and the USB port is active use with a "remote" printer.
Similar Messages
-
Bridging network with AP Extreme base station and AP Express
OK, here's the deal. I have an Airport Extreme Base Station on a WPA2 Personal network. Works great except that I want to boost the signal to the rest of the house. So, I bought an Airport Express. Airport Utility picks up both devices; but when I select the new Express to configure it, I get a msg asking to confirm that I want to switch networks. Well, I don't. I want to expand the network I have. Last night I did click "yes" and it was a disaster as I lost the Extreme altogether and the Express couldn't pick up a signal because - obviously - it wasn't connected to the ethernet cable as the base station, and also because (I think) the base station is configured to hide my SSID. I ended up working backwards and got the Extreme back to normal and put the Express back in its box until someone can tell me how to do this. I know Apple says it's easy; but it's a challenge for me. HELP!
A few things:
1. Please don't configure your base station to "hide its SSID". Doing this is absolutely useless as a security method. It will on the other hand complicate setup of your network, as well as the diagnosis of problems when they arise.
2. You must allow the Airport Utility to switch networks during the process. What is happening is that the Airport Utility must temporarily switch your Mac's wireless network connection from your existing base station to the wireless network created by your unconfigured Airport Express in order to communicate with and configure that Airport Express. After the Airport Express configuration is complete - if your Mac doesn't automatically switch your Mac's wireless network connection back again then just do so manually from the MacOS Airport menu.
3. To get a better understanding of what you are doing, start reading at page 42 of Apple's manual "Designing Airport Networks" found at:
http://manuals.info.apple.com/en/DesigningAirPort_Networks_Using_AirPortUtility.pdf -
How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet
This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network" -
I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.
Which version of the AirPort Utility are you using?
-
Difference between AirPort Extreme base station and airport express
What is the difference between AirPort Extreme base station and airport express
Please see this Apple comparision document for details. Post back on any specific questions including your specific requirements.
http://www.apple.com/compare-wifi-models/ -
I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?
apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together. -
HOW do I get my Extreme base station and Express to join a Linksys network?
OK... so I have FINALLY enabled my SLINGBOX to view remotely by totally removing my Airport Extreme & Express from the network look. I was told they are both routers and I have to pick one. The Linksys network works fine for all networking purposes... what it WON'T DO is connect my USB printer or stream iTunes to remote speakers. NOW, I have been told by using the Extreme & Express in "client mode" I can do this.
Basically HOW do I get my Extreme base station and Express to join the exsiting Linksys network?Sorry but the AirPort Extreme base station (AEBS) does NOT have a client mode.
The AirPort Express (AX) does have a client mode. The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode. -
I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
ThanksThe netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you. -
Vonage, AirPort Extreme Base Station, and Comcast
I just picked up an Airport Extreme Base Station, and wanted to use it to get my MacBook Pro on my home network. However, I can't get it to actually provide an network connection to the MacBook. In the Network pane of System Preferences, under the Network Status, AirPort has a yellow icon, and the following message: "AirPort is connected to the network HulkNet. AirPort has a self-assigned IP address and may not be able to connect to the Internet."
Here's my current setup:
Comcast > Cable Modem > LinkSys RTP300 > PowerMac, PC, AEBS
I have the "Distribute IP addresses" disabled on the AirPort, and the internet for the PowerMac & the PC work fine. In the network status of the RTP300, the AEBS is listed as having an IP address of it's own.
Any gurus out there that can help me figure this out? I just want to be able to access my home network from anywhere in the house!All,
I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes? -
Airport Extreme Base Station and 2wire Modem / Router
I have Yahoo DSL with a 2wire modem / wireless router combo. I have an iMac and a MacBook both running Leopard. I can't seem to get the Back to my Mac feature to work. I'm currently running the trial version of .Mac. I'd like to get a full .Mac account but I want to be sure I can utilize the Back to my Mac feature. If I were to bridge an Airport Extreme Base Station to the 2wire would that solve my issue with Back to my Mac. Additionally I like the idea of being able to plug a printer of external hard drive into the Airport Extreme.
Any advice is greatly appreciated.I got it to work. I purchased the Airport Extreme Base Station and took the following steps which I found here http://forums.macosxhints.com/archive/index.php/t-68141.html
First connect directly to the 2Wire with the Ethernet cable.
Instructions from 2Wire:
1. Clear the HomePortal to Factory State –can be accomplished two ways
2. Go to http://homeportal/management
3. Click on Resets
4. Click on Reset to Factory State
5. Click Continue
6. Have customer press Hardware Reset button with paperclip (HG products only and BellSouth HWs)
7. Have customer unbend a paperclip
8. Have customer insert paperclip into recess for Hardware Reset button (outlined with Red circle) on back of HomePortal.
9. Hold paper clip in for ten (10) full seconds
Next steps:
1. Go to http://homeportal/management again
2. Click on Configure under Broadband Link
3. Enter VPI 0 and VCI 35
4. Click on Disable PVC Search
5. Set Connection Type to Direct IP
6. Click Submit/Save
7. Have cu go to http://homeportal/management
8. Click on Configure Services
9. Have cu Uncheck Enable Routing
10. Click Submit
Airport configuration:
1. Open the AirPort Admin Utility and select your Base Station.
2. Click Configure and enter your password.
3. Click the Internet tab.
4. Choose PPP over Ethernet (PPPoE) from the Connect using pop-up menu.
5. If required by your ISP, enter your user name, password and service name in the appropriate fields. ( Your name and password is you full email including the @sbcglobal.net part and your email password)
6. Click Update.
7. After the base station restarts itself, quit the AirPort Admin Utility.
If that doesn’t work call apple and they should be able to help with the airport configuration.
Back to My Mac now works. Hope this helps someone else.
Message was edited by: WalrusBoy -
Hi I'm from Australia.
If I buy an Apple Airport Extreme Base Station and I have an Optus Cable internet. Do I really need an Apple Care Protection? or I don't have to?Any specific recommendations for a standalone ADSL modem though?
Always a good idea to use the modem that your service provider supplies or recommends....often free....since you know that it will be supported in the event of connection difficulties.
I have made the mistake of choosing the "best" modem based on test reports....only to find out later that the ISP would not offer any support when I was having connection difficulties.
The ISP blamed the modem. The modem support folks blamed the ISP. -
i have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it
Read the user guide:
http://support.apple.com/manuals/#airport -
my cable modem works fine, but when I hook it up to my extreme base station and run through the prompts and set up my wireless network it doesnt work and neither does my apple tv by default. I am unsure how to correct this problem. It will come up saying that I dont have an IP address when I have it set to DCHP so I dont know what the problem is.
Push the reset button on the modem and power the modem off
Power off everything else....all devices....order is not important
Wait 15-20 minutes or longer
Connect the Ethernet cable from the modem to the WAN port (circle of dots icon) on the AirPort Extreme
Power up the modem and let it run for 5 minutes by itself
Power up the AirPort Extreme and let it run for 5 minutes
Power up each other device one at a time a few minutes apart
Check the network -
I have an aiport extreme base station in my living room and an airport express in my bedroom extending the network. For some reason my xbox along with some other devices always connects to the extreme base station in the living room which has a very low signal. Is there a way to setup a seperate network for my express extender so that I can connect only certain devices? HELP
You would probably want your Express to join the network if an extender isn't required. Reset to factory settings and join the network.
If you do want your Express as an extender run an Ethernet cable between the Express and the Verizon router and set the Express up to be in bridge mode, with the same WiFi network name and password as your Verizon router. -
Airport extreme base station and expresses
Does anyone know how many airport expresses can work off of one base station? I have a airport extreme base station 802n about 2 years old. I currentoy have two expresses linked and would liek to add a third.
Also, is there any value in buying a current model base station --- in terms of wifi capability? It seems our movie download performance has signeificantly slowed in the last year as we hae more devices in our home that use wifi. ThanksYou might try asking this question in the Airport forum.
Here's a link for you:
https://discussions.apple.com/community/wireless/airport
Maybe you are looking for
-
Goods and delivery cost processing at one instance through MIRO
Hello, Is there any possibility of doing bill wise MIRO for both goods and planned delivery cost in a single screen apart from refering PO and option goods+planned delivery cost? The scenario is; vendor is common for both goods and delivery cost,orga
-
I can't fathom the reasoning behind ID CS5 tables. Can you help?
I can make ID CS5 tables work, but I don't understand how they work. I should mention that I'm a heavy FrameMaker user, so I'm sure I've got some faulty preconceptions. In FrameMaker, I'm accustomed to using table styles to automate table formatting.
-
Hi All, We are facing a strange problem. We have created a PO with 12 line items. All these line items are having a same Tax Code. The tax so calculated has to be inventorised. Accordingly in tax procedure we have assigned an account key for this con
-
Reboot the iphone to install a program and has been left all the time with the apple on the screen
reboot the iphone to install a program and has been left all the time with the apple on the screen. takes so hours without turning away. I can do?
-
Default Calendar Option being ignored in iOS7
I seem to be having an issue with the Calendar, after upgrading to iOS7. (7.0.2) I have multiple calendars synced to my Exchange email account. In previous versions (iOS6 for example), I have been able to change the default Calendar that all new appo