Airport Extreme ver. g Failed security check for my credit card processing!

Hope this hasn't just been addressed here but I signed up for a new credit card processing service and they have a company called securitymetrics that checks the level of safety for your cc processing setup.
I failed the check due to Airport Extreme settings and don't know how to fix it.
Short version:
failure 1:Your computer is answering ping requests. Hackers use Ping to scan the Internet to see if computers will answer. If your computer answers then a hacker will know your computer exists and your computer could become a hacker target. You should install a firewall or turn off Ping requests.
failure 2:It is possible to gather information about the remote base station (such as its connection type or connection time) by sending packets to UDP port 192. An attacker connected to this network may also use this protocol to force the base station to disconnect from the network if it is using PPPoE, thus causing a denial of service for the other users. Solution: Filter incoming traffic to this port and make sure only authorized hosts can connect to the wireless network this base station listens on.
Anyone know how to address these? I looked at the settings on Airport Utility and couldn't find anything.

You would enter 192 in both the Public & Private UDP/TCP entries. The Private IP Address would be an address of a non-existent device. For example, if the DHCP range is 10.0.1.2 - 10.0.1.200, enter 10.0.1.201 for this entry. (This, of course, would mean you do not have a client assigned this IP.)

Similar Messages

  • I am trying to update some apps but my ipad wont let me because it wants me to enter the security code for my credit card and I dont want to do that so how do i fix this?

    I am trying to update some apps but my ipad wont let me because it wants me to enter the security code for my credit card and I dont want to do that how can i fix this?

    Try temporarily disabling your firewall and antivirus.

  • How do i set a security code for my credit card

    How do i set a new security code for my credit card?  My daughter is going over her set limit & i need to change the code again. I paid 19.99 last time to get her old i pod setup that is no longer working.  Do i have to pay apple support again or is there some steps i can go through to set a new security code?

    Log into yur account and change/add the necessary information
    iTunes Store: Changing Account Information

  • ITunes keeps prompting me to reenter the security code for my credit card each time I make a purchase

    ITunes keeps prompting me to reenter the security code for my credit card each time I make a purchase, saying my Windows 7 PC is a new device. However, the PC is on iTune's list of authorized devices for downloads. What's causing this? I do block cookies etc on browsers.

    I don't know. No, it doesn't use your browser. Perhaps you should call and find out what the problem is.
    Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
    To contact product and tech support: Contacting Apple for support and service - this includes
    international calling numbers..
    For Mac App Store: Apple - Support - Mac App Store.
    For iTunes: Apple - Support - iTunes.

  • Anyone else having trouble with Itunes store? My account says I have entered the wrong security code for my credit card

    Anyone else having trouble with Itunes store? My account says I have entered the wrong security code for my credit card

    Yes, it happens to me all the time. I deleted an app because it froze the. Tried to redownloading it but it wouldn't let me ivd tried all of my cards and nothing works. I thought it was because I had a negative balance but I have a to of money all accounts. It'd be very helpful if someone could help us out.

  • HT1918 When I go to use my account, it tell me my security code for my credit card is wrong? I just update this a few weeks ago, and was working fine till last night.

    Can not use my account, telling me the security code on my credit card is wrong, just update this a few weeks ago, was working fine until last night.

    Take a look here:
    http://support.apple.com/kb/TS1646
    If that doesn't help, go here:
    http://www.apple.com/support/itunes/contact/
    and follow the instructions to report the issue to the iTunes Store.
    Regards.

  • HT1311 when I try to enter the security code for my credit card then I click the "done" icon in the top right corner of the phone my security code does not save

    title says it all...

    If all your creditcard details are correct, you should be able to login and make purchases.
    Please note however, that the security code (CVC code) can be asked by apple on several occassions (f.e. when you're using a device for the first time) to confirm you're the credit card owner.
    Hopefully my post helps you out. Please click the "This solved my question" or "This helped me" button if appropriate.
    Cheers,
    Wouter

  • When I tried updating my apps it says invalid security code for my credit card.

    Basically when I try updating an app it says to login. Ok say once I log in it makes me update billing info. When I put my cc info in (which has a 0$ balance) it says invalid security code. This is complete ********, I can't even download FREE apps OR update the ones I have. Im considering going back to android. This is ridiculous.

    you cannot place a card on the account that has no balance to it...
    you can hit the "None" option if you owe nothing to the itunes store
    iTunes Store: My credit card's security code or zip code does not ...

  • HT1657 hi i have a 25 doller credit in my itunes but i want to rent a movie on my apple tv and it wants my security coad for my credit card,i dont want to use my credit card to rent one

    how can i use my itunes credit on my apple tv

    Try redeeminging an iTunes gift card into the account.
    Next
    Create a NEW account using these instructions. Make sure you follow the instructions. Many do not and if you do not you will not get the None option. You must use an email address that you have not used with Apple before.
      Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card

  • HT3546 I have been unsuccessfully trying to extend the wifi of my Time 2T Capsule with an Airport Extreme 2nd Gen. It works for a while and then loses configuration. I have done everything possible, disconnected it, reset it but it keeps failing, what to

    I have been unsuccessfully trying to extend the wifi of my Time 2T Capsule with an Airport Extreme 2nd Gen. It works for a while and then loses configuration. I have done everything possible, disconnected it, reset it but it keeps failing, what to do?

    What model and firmware is the 2TB TC?
    What firmware is the AE?
    Does the AE get good signal from the TC in its current location?
    Signal can only be extended that is received intact.
    Is it extending on 5ghz? As I remember it a Gen2 AE is only single band, although you can choose either 2.4ghz or 5ghz.
    I am fairly sure you are going to tell me your TC is AC model..
    I would do a couple of things..
    1. Fix the wireless name, make it short, no spaces and pure alphanumeric.
    2. Fix the wireless channel for 2.4ghz so it is not going to jump around.
    3. Get real results from the AE in its current location for signal strength.. this is really only possible on v5 utility. And that is a double pain with Mavericks because you cannot use it.
    Apple have removed all the useful diagnostics from the airport utility. There is next to nothing left. So you need to use the computer and its diagnostics to find signal levels in the location.
    http://support.apple.com/kb/HT5606

  • How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

    How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
    When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro.  What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
    WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
    NOTE:  If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
    Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did.  He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
    Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse. 
    THIS IS WHAT YOU WILL NEED TO DO:
    First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
    down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up.  If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it.  Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

    I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
    I have a Linksys WRT320N I used for the initial Charter setup.
    I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
    Hasn't caused any issues so far but one thing I did notice.
    On the Linksys there were 3 DNS servers listed.
    The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
    I tried everything above, but light on modem still flashes yellow.
    I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
    I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

  • I have a time capsule and airport express one floor lower, the signal keeps dropping. Would an airport extreme give me a longer range for wifi?

    I have several computers. My equipment is upstairs in a house, apple time capsule and downstairs airport express. Lately the downstairs computer keeps disconnecting from the internet. Would replacing the airport express with and airport extreme give me a greater range for my wifi connections?

    Yes.  Question is... would the difference be enough.
    The extreme has a bigger & more powerful antena array. But if that alone still doesn't suffice, you also have the option to use the express to EXTEND from the Extreme.

  • Mac OS X 10.6.8, receiving error message "Failed to check for updates. The operation couldn't be completed. Operation not permitted." How to fix?

    When I try to update my software, I'm receiving the error message "Failed to check for updates. The operation couldn't be completed. Operation not permitted."
    I'm using Safari 4.0.3. Yes, I know this is an old version of Safari - I can't update it, or any other software on my MacBook. Should I just wait for the Lion OS, or is there any kind of fix a non-technical Mac user like me can attempt without screwing up her laptop?
    I've tried clearing my cache and resetting Safari already - doesn't help. I've also tried to update after disabling my (Norton) antivirus software, thinking that might be interfering. None of these help.
    I don't know if it's a related problem, but also I can't download .pdf files from the internet, although I used to be able to.

    You should use the NortonAV uninstaller to uninstall it. Disabling the dreadful thing in the past hasn't always been sufficient for it to cease creating system havoc. The Mac NortonAV version has a long and well-earned reputation for doing truly seriously nasty things to OS X. Shame on Comcast for inflicting NortonAV on its Mac customers. It's not a matter of if NortonAV will mess up OS X but when and how badly. I can't help but wondering if some setting in your Norton AV has decided that NortonAV, rather than you, will be making executive decisions about what you are allowed to install on your computer and is keeping that fact a secret.
    After you are done uninstalling Norton use the finder to search for any Norton files that the uninstaller might have missed. Add the option to search for invisible files.
    After you have removed all the Norton bits and pieces restart in safe mode by holding down the shift key right after the startup chime. Keep holding down the shift key until you see the Apple logo and spinning gear. Safe mode does some maintenance tasks which means a much longer than normal startup time. Use Disk Utility to repair permission
    If your Mac works normally in safe mode restart. If things still aren't fixed you might want to give another shot at reinstalling Snow Leopard from the install DVD and applying the Mac OS X 10.6.8 Update Combo before taking your Mac to the Apple Store.
    If you feel the need to run AV software on your Mac use ClamXav in manual mode. It's donationware and doesn't seem to cause the litany of weird problems that are associated with other AV software.

  • I have clicked the Apple  Software Update,a window pops up with Failed to check for updates.The operation couldn t be completed. Operation not permitted.This only occurring now did not happen previously.I am using 10.7.4,on a Mbp Pro.

    I have clicked the Apple > Software Update,a window pops up with >Failed to check for updates.
    The operation could not completed. >Operation not permitted. This is only occuring now.It did not happen
    before.The Apple store in Sydney NSW Australia only reinstalled 10.7.4 Lion yesterday.I have downloaded my
    Itunes song and reinstalled Intego antivirus.Will somebody please advise me what to do.It is 4:03 PM Saturday
    here in Koolewong.
                        richard.

    Uninstall Intego...you don't need it.

  • Is it possible to use time capsule or airport extreme as a wireless hard drive for iphone?

    Is it possible to use time capsule or airport extreme as a wireless hard drive for iphone.
    I would like to strem movies from the hard drive to iphone.
    I have already seen the Goflex Stellite, which works this way.
    Is there any other device that could do this?

    I did a typo. My current computer is a 2010 1/2 iMac.  The stand alone monitors are still out of my price range so I'm looking for other options. By buying an external hard drive and a broken iMac, I'm still ahead. Still, if I understand you right, the 27" 2010 and earlier iMacs  would be possiblities.
    Are there adapters that would allow me to run a 2011 and newer iMac as an external monitor from my 2010 1/2. There are so many adapters out there these days.

Maybe you are looking for